斜坡地基刚性桩水平承载力上限分析

为探讨斜坡地基刚性桩水平极限承载力的计算方法，介绍柔性桩的等效刚性桩有效嵌入深度并引入极限水平地基反力分布形式。根据荷载指向坡外及坡内两种情况，提出适用于斜坡地基桩前土体的两种极限破坏模式。然后，基于极限分析上限定理，推导出两种荷载方向下的刚性桩极限承载力，并引入多组现场试验，验证了理论方法的合理性。探讨了边坡坡角、内摩擦角、黏聚力及荷载方向对极限承载力的影响，得出了一些规律性结论，并基于以上分析结果，提出斜坡地基刚性桩水平极限承载力随坡角变化的拟合公式。这些分析为斜坡地基上基桩设计提供了一定的参考，具有理论及工程应用价值。     

临近边坡的条形基础地基极限承载力数值分析

建筑物或构筑物基础临近边坡置放的情况在实际工程中十分普遍,但目前对于临近边坡基础的地基承载力及破坏模式尚缺乏深入研究。采用不连续布局优化（DLO）极限分析法建立数值模型,分析边坡几何尺寸、土体参数和基础位置对临坡条形基础的极限承载力和边坡破坏模式的影响,并对国内外现行规范推荐的计算方法进行评价。结果表明：极限承载力随边坡高度和边坡倾斜角的增大而减小,当坡高超过临界高度后,极限承载力将不受其影响;极限承载力随土体黏聚力和内摩擦角的增大而提高,滑动面随黏聚力的增大而变浅,随内摩擦角的增大而变深;极限承载力随基础与坡肩相对距离的增大而提高,当基础置放位置超过某临界距离后极限承载力不受边坡影响。在土体强度高、坡角较大时,《建筑地基基础设计规范》规定的临坡基础最小置放距离偏于危险,设计时仍需考虑边坡对承载力的减损作用;在土体强度较低、坡角较小时,规范规定值偏于保守。美国AASHTO规范对边坡地基极限承载力的取值在砂土边坡时较为可靠,但其仅适用于坡面破坏模式的情况;饱和黏土边坡的承载力曲线有悖于理论解,对临界距离的规定同样存在低估。     

Bearing Capacity of Embedded Strip Footings on Cohesionless Soil Under Vertical and Horizontal Loads

In the last decades a few attention was given to the evaluation of the bearing capacity of embedded footing under inclined loads on a frictional soil. This paper focuses on a numerical study using the finite-difference code Fast Lagrangian Analysis of Continua (FLAC), to evaluate the bearing capacity of embedded strip footing on a frictional soil. The soil is modeled by an elasto-plastic model with a Mohr–Coulomb yield criterion and associative flow rule; the effect of non-associativity of the soil on the bearing capacity is also investigated. The effect of the embedment is estimated though a depth factor, defined as a ratio of the bearing capacity of a strip footing at a depth D to that of a strip footing at the ground surface. The inclination effect is estimated by inclination factors, defined as the ratio of the limit vertical load for a footing under inclined loading to that of the vertically loaded footing. Both swipe and probe analyses were carried out to identify the vertical force–horizontal force (V–H) failure envelope. The results have been compared with those available in the literature.     

Effect of Edge Distance from the Slope Crest on the Response of a Laterally Loaded Pile in Sloping Ground

Compared to the field tests, the numerical modelling is an economical way to analyze the response of laterally loaded piles in sloping grounds. This paper presents a three-dimensional finite element analysis to investigate the effect of edge distance from the slope crest of a laterally loaded pile embedded in the sloping ground for different slope angles and pile lengths. The results show that the pile top displacement and the bending moment in the pile decrease with an increase in the edge distance, whereas they increase as the slope angle is increased. The response of the pile in sloping ground is compared with its response in the level ground. The comparison is used to develop a simple methodology for estimating the pile top displacement and the maximum bending moment for any edge distance from the slope crest considering their values for level ground.     

上拔扩底基础与地基土体承载特性差异性分析

工程中多采用基础上拔静载试验中基础顶部荷载-位移曲线获取基础的承载力,忽略了基础周围土体的变形破坏过程,而实际工程中均是基础周围地基土体发生破坏。为研究扩底基础与其周围土体在抗拔承载特性方面的差异,以黄土地基中的9个扩底基础为研究对象,通过现场全尺寸基础的上拔静载试验,分别获得基础顶部与地表的上拔荷载-位移曲线,并进一步对基顶与地表处的荷载-位移曲线变化特征、抗拔承载力取值进行对比分析。结果表明,两处的荷载-位移曲线变化特征相似,相同上拔荷载作用下地表处的位移量均小于基础处位移量,差异以初始弹性阶段变形最为突出;两者在弹性极限荷载QL1取值方面,相差较大,但随着地基基础由弹性向塑性发展,差异逐渐减小,两者塑性极限荷载QL2取值基本相同。结合上拔扩底基础的破坏模式,分析出上述差异主要由于基础与周围土体之间变形不协调所致,加载初期基础顶部的上拔位移包括基础拔出量和上部土体压缩量,当上部土体压密后压缩变形消失,地基基础成为一个整体,上拔基础与周围土体的变形趋于协调。     

Bearing capacity of foundations on slopes

By applying the lower bound finite element limit analysis in conjunction with non-linear optimisation, the bearing capacity factors, N_c, N_q and N_γ, due to the components of cohesion, surcharge and unit weight, respectively, have been estimated for a horizontal strip footing placed along a sloping ground surface. The variation of N_c, N_q and N_γ with changes in slope angle (β) for different soil friction angle (φ) have been computed for smooth as well as rough strip footings. The analysis reveals that along a sloping ground surface, in addition to N_γ, the factors N_c and N_q also vary considerably with changes in footing roughness. Compared to the smooth footing, the extent of the plastic zone around the footing becomes greater for the rough footing. The results obtained from the analysis are found to compare well with those previously reported in literature.     

Pseudo-static Seismic Bearing Capacity of Shallow Foundations in Unsaturated Soils Employing Limit Equilibrium Method

There exist many structures founded on unsaturated soil deposits. Shear strength augmentation due to the evolution of the matric suction within the unsaturated porous media enhances the bearing capacity of the overlying foundation. This paper presents the evaluation of the pseudo-static seismic bearing capacity of the shallow foundations resting on unsaturated soil deposits using limit equilibrium method. Adopting the Coulomb failure mechanism and Bishop effective stress concept, the bearing capacity equations are solved. The distribution of the matric suction beneath the footing is assumed to be linear. The results of the bearing capacity evaluation are validated against some experimental data found in literature for the static condition. For the seismic loading consideration, the pseudo-static method is utilized. The dual effect of the earthquake acceleration vertical component is thoroughly discussed and a suction transition point is introduced in which the minimum bearing capacity is observed to bear the same value for both upward and downward directions. The increase in the matric suction throughout the soil deposit leads to the increase in the soil shear strength, thus posing more resisting forces as well as higher ultimate bearing capacity. The offered solution is deemed a consistent and useful tool for the accurate prediction of the seismic bearing capacity of shallow footings resting on unsaturated soil deposits.

     

Stability of eccentrically loaded footings on slopes

The stability of eccentrically loaded strip footings on slopes was investigated using the method of finite element analysis based on the theory of elasto-plasticity. The analysis was done for two different soils involving three levels of slope angle, six footing locations, and two levels of load eccentricity plus central vertical loading. The strip footing analysed was a 3-ft (0.9 m) wide reinforced concrete footing embedded to a depth of 3 ft (0.9 m). The analysis focused on footing settlement, plastic yielding of soil, and ultimate bearing capacity. The results of analysis show that the influence of load eccentricity on footing pressure vs. footing centre settlement is negligibly small. However, the progressive soil yielding and ultimate bearing capacity are greatly affected by load eccentricity. Furthermore, the effect of load eccentricity differs considerably with the load location relative to the footing centre and slope crest. The ultimate bearing capacity for the eccentric load located on the slope side is significantly greater than that for the load located on the other side of the footing centre. For a 2(H): 1(V) slope in silty clay, the effect of slope on footing stability decreases with increasing footing location from slope crest as would be expected, and diminishes when the footing is located from the crest at about 5-times the footing width.     

Seismic Bearing Capacity of Strip Footings Located Close to the Crest of Geosynthetic Reinforced Soil Structures

This paper investigates the performance of geo-reinforced soil structures subjected to loading applied to strip footings positioned close to a slope crest. The kinematic theorem of limit analysis, which is based on the upper bound theory of plasticity, is applied for evaluating the ultimate bearing capacity within the framework of pseudo-static approach to account for earthquake effects. The mechanism considered in this analysis is a logarithmic spiral failure surface, which is assumed to start at the edge of the loaded area far from the slope, consistent with the observed failure mechanisms shown in the experimental tests reported in the literature. A parametric study is then carried out to investigate the influence of various parameters including the geosynthetic configuration, backfill soil friction angle, footing distances from the crest of the slope, slope angles and horizontal seismic coefficients. Attention is paid to the failure mechanism because its maximum depth is the depth at least to which the reinforcements must be placed. Results of the analyses are presented in the form of non-dimensional design charts for practical use. Finally, a simple procedure based on the assessment of earthquake-induced permanent displacements is shown for the design of footing resting on reinforced slopes subjected to earthquake.     

土钉加固黏性土坡加载的离心模型试验研究

进行了不同坡度土钉加固边坡坡顶加载的离心模型试验,观测了土坡的破坏过程并测量土坡的位移场,研究了土钉加固黏性土坡的承载力、变形和破坏规律以及坡角对其破坏规律的影响。试验结果表明,坡顶荷载的增加引起土坡变形的增加,变形的集中产生和发展导致滑裂面的形成并使土坡发生破坏。土钉变形规律受加载阶段和加载底板的综合影响,坡顶荷载越大,接近坡顶的土钉弯曲挠度越大,钉土间的相互作用越强。土坡的坡角越大,承载力越低,土体呈现出更显著的向坡面位移的趋势。     

基于非对称双侧破坏模式的临坡地基承载力上限分析

临坡地基已成为一种广泛的地基形式。针对临坡条形基础地基破坏模式的非对称性特点,首先引进双侧破坏模式的研究思路,重点考虑临坡地基基础两侧滑块大小和同一滑块几何形状的双重非对称性特征,构建了临坡条形基础地基非对称双侧破坏模式,为临坡地基承载力分析奠定了坚实基础;然后在此基础上,引进极限上限分析和优化理论,建立了临坡条形基础地基承载力分析的模型与方法,该方法不仅可考虑地基破坏模式,还可考虑基础与坡顶距离对临坡地基承载力的影响,而且还可较好地蜕化为平地地基承载力的分析;最后通过工程实例计算,并与现有相关分析方法进行对比分析,表明该方法的可行性与合理性以及普遍适用性。     

Elasto-viscoplastic finite element study of the effect of degradation on bearing capacity of footing on clay ground

The bearing capacity of footing has been studied by both conventional and numerical methods by many researchers. However, degradation of the microstructure of material, that is, a change in the microstructure of the soil, has not been adequately taken into account. Degradation of microstructure causes strain softening of materials and it leads to strain localization such as shear bands and slip bands. From an engineering point of view the strain localization is crucial because it is a precursor of failure. In the present study, finite element analyses of the bearing capacity of a shallow foundation on homogeneous and inhomogeneous saturated clay strata have been conducted using an elasto-viscoplastic soil constitutive model of microstructure change. A series of analyses of footing on clay deposit with different microstructure parameters have been carried out. Numerical results show that strain localization can be predicted during the loading of rigid footing on highly structured soil and strain localization affects the footing–soil interaction. The effects of footing roughness on the failure mechanism are also discussed in the study.     

Seismic bearing capacity of shallow foundations near rock slopes using the generalized Hoek–Brown criterion

The seismic bearing capacity of shallow foundations resting on a modified Hoek–Brown rock mass is investigated within the framework of the kinematic approach of limit analysis theory. The analysis focuses on evaluating the reduction in bearing capacity induced by seismic loading and by the proximity of a rock slope. A pseudo‐static approach is adopted to account for the earthquake effects for the seismic bearing capacity evaluations. At the rock material level, the closed‐form expressions previously obtained for the support functions of the rock failure criterion allow the implementation of different failure mechanisms families, and thus to derive rigorous upper bounds estimates of the load‐bearing capacity in both static and seismic conditions. The effects of geometrical, strength and loading parameters are assessed through a large number of parametric computations. Finally, design tables are presented for practical use in rock engineering. Copyright © 2010 John Wiley & Sons, Ltd.     

无厚度界面单元边坡浅基础极限承载力上限值的数值分析

采用研发的有限单元分析程序,并同时考虑以库仑摩擦界面为组成模式的多段式无厚度界面单元,藉以探讨边坡坡角与坡缘距离对边坡坡顶浅基础极限承载力的影响,并应用于不同几何破坏机制条件,计算边坡基础在凝聚性土体的最小荷载上限值,模拟土体间的滑动破坏趋势与渐进式破坏行为。研究分析内容包含：（1）浅基础位于半无限空间;（2）在不同边坡坡角条件下,浅基础位于坡顶边缘处;（3）在不同边坡坡角条件下,浅基础位于不同坡缘距离等。经由数值计算分析结果显示,坡缘距离值愈小或边坡坡角愈陡峭时,边坡浅基础极限承载力值则愈小。换言之,当浅基础位于坡顶边缘处且坡角为垂直开挖情况时,则导致浅基础极限承载力降低约50 %。     

统一强度理论在地基承载力确定中的应用研究

基于统一强度理论,考虑中间主应力对地基承载力的影响,给出了静止侧压力系数 条件下的地基临塑与临界荷载公式。结合实例,对基于统一强度理论和Mohr-Coulomb准则的地基承载力计算结果进行了对比分析。新的理论公式更为确切地反映了地基承载力的实质,有利于地基土体强度的充分发挥。基于河北境内177组不同土质地基的土性指标及载荷试验资料的统计分析,对中间主应力系数b的取值进行了深入细致的探讨,研究表明,对于粉土及黏性土地基,b的取值范围在0～0.5之间变化,理论计算所得地基承载力特征值与载荷试验实测值间的相对误差一般不超过5%     

Bearing capacity of sandy soil treated by Kenaf fibre geotextile

Bio-based materials are widely used recently in order to introduce a more sustainable construction material. Kenaf is a type of bio-based material that can be easily obtained in a tropical country, which could be a potential material to be utilised as a geotextile material because it has good tensile strength. The geotextile could be used to improve the bearing capacity of a loose soil. This paper presents a series of small-scale physical modelling tests to investigate the bearing capacity performance of Kenaf fibre geotextile laid on and inside the sand layer. A rigid footing was used to replicate a strip footing during the loading test, and sand was prepared based on 50% of relative density in a rigid testing chamber for ground model preparation. In order to treat the soil, Kenaf fibre geotextile was laid at four difference locations which are on the soil surface and underneath the ground model surface at 50, 75 and 100 mm deep. It was found that the usage of the Kenaf fibre geotextile has improved the bearing capacity of the sandy soil up to 414.9% as compared to untreated soil. It was also found that the depth of the Kenaf fibre geotextile treated into the soil also affects the soil performance.     

Seismic Bearing Capacity of Shallow Strip Footing with Coulomb Failure Mechanism using Limit Equilibrium Method

In this paper, an effort is made to evaluate the seismic bearing capacity of shallow strip footing resting on c–ф soil. The formulation is developed to get a single coefficient of bearing capacity for simultaneous resistance of weight, surcharge and cohesion. Limit equilibrium method in Pseudo-static approach with Coulomb mechanism is applied here to evaluate the seismic bearing capacity. The seismic bearing capacity of footing (q_uE) is expressed in terms of single coefficient N_γE. The effect of various parameters viz. angle of internal friction of soil (ф), angle of wall friction (δ), cohesion (c), ratio of depth to width of footing (d_f/B₀), seismic acceleration (k_h, k_v) are studied on the variation of seismic bearing capacity co-efficients.     

Experimental and numerical investigation of slope stabilization by stone columns

In this study, an investigation has been performed on a small-scaled laboratory model and its numerical model by the code of PLAXIS to see the effect of stone columns (SCs) placed vertically in a soft soil slope in terms of slope stability, bearing capacity, and settlements. Also, several hypothetical cases have been examined by the code. Effect of s/D ratios (distance between the vertical axes of SCs/diameter of SCs) was also investigated on slope stability, ultimate bearing capacity, and settlement of a footing rested on top of the slope on the laboratory model. Firstly, ultimate bearing capacity and settlement properties of soil were determined for unreinforced soil that is no SCs were considered. Then, some values of soil were determined after the installation of stone columns with various ratios of s/D. The ratios of s/D were 2, 3, 3.5, and 4. The tests carried out on the laboratory model were simulated and numerically analyzed in two dimensions under plain-strain conditions by Mohr?CCoulomb model. In the analyses, PLAXIS computer code, which is based on finite elements method, has been employed. Then, a parametric investigation was carried out to see the effect of SCs on the stability of the slope. In the parametric investigation, several hypothetical cases that were one layer of soil and two layers of soil with the presence of water in the reservoir side of the slopes were examined. The analyses in the investigation were performed by the PLAXIS code for various slope angles ??, ratios of c/(??H), and ratios of s/D. From the test results of the laboratory model, and the results obtained from the numerical analyses, it was observed that the bearing capacity of the footing constructed on the top of the slope in soft soil was increased; settlements were decreased after the improvement with SCs. From the analyses performed, it was found that the SCs increased the stability of slope 1.18- to 1.62-fold as a relative effect of different parameters.     

柔性荷载下粉喷桩复合地基承载特性试验研究

开展了粉喷桩复合地基承载性能试验,实测了柔性荷载下桩、土应力,探讨了复合地基中桩土应力比及其变化规律。研究表明,粉喷桩复合地基载荷-沉降曲线一般表现为缓变型;粉喷桩复合地基承载力宜按相对沉降法取相对沉降比为0.01所对应的压力。由于砂垫层的流动补偿作用,柔性荷载下桩土应力比随荷载的增加变化较为平缓,在复合地基承载力基本值附近桩土应力比变化范围为1.73～6.83,平均值为3.20。     

斜坡基桩水平极限承载力及影响因素模型试验和数值模拟

斜坡上的基桩具有承重和阻滑的双重功能,其受力变形性状远比平地上的情形复杂。采用模型试验和数值模拟相结合的方法研究了其水平承载特性及影响因素。模型试验结果表明：临坡距对基桩的水平承载变形性能有较大影响。同一级荷载下,临坡距较大的桩身水平位移小于临坡距较小的基桩;临坡距较大基桩的临界荷载和极限承载力也大于临坡距小的基桩。数值模拟研究结果表明：基桩水平极限承载力随着斜坡坡比的增大而减小,随着临坡距的增大而增大,与模型试验的结果基本一致。对比分析了斜坡和平地基桩水平承载变形性能的差别,得出了可考虑坡比和临坡距的斜坡基桩水平极限承载力简便计算方法,可为有关规范的修订以及工程设计提供参考。