考虑涡激运动下海洋柔性立管的疲劳损伤分析

基于ABAQUS/AQUA模块,当Spar平台发生涡激运动时,对与平台相连接的柔性立管进行时域动态响应分析,得到了不同折合速度下柔性立管的应力响应曲线.对立管触地区域和悬垂段进行了细化的分析,并利用S-N曲线和Miner线性累积损伤理论对平台涡激运动引起的柔性立管疲劳损伤进行了计算.研究结果表明:平台涡激运动对立管触地区域和悬垂段的影响较大,这两部分最容易在长时间的工作中产生疲劳损伤.特别是平台运动到近点时,立管触地区域受到的应力急剧增加,这个区域是立管工作的危险区域,应该特别注意.该研究结论可以作为立管结构设计和海底铺设时的参考,通过增加立管触地区域的结构强度和优化铺设方式,从而来提高立管的疲劳寿命和系统的安全性.     

大长细比柔性杆件涡激振动实验

涡激振动(vortex-induced vibration,VIV)是导致深海细长柔性立管发生疲劳破坏的重要因素。采用实验观测手段研究了长细比为1 750的柔性立管多模态涡激振动特性。实验中,通过采用拖车拖拉立管模型在水池中匀速行进来模拟均匀流作用下的涡激振动响应。利用光纤光栅传感器测量立管模型在横流向(cross-flow,CF)和顺流向(in-line,IL)的应变,进而通过模态分解的方法,获得立管模型涡激振动的位移。在此基础上,研究了CF以及IL方向的响应频率、位移标准差的平均值和最大值等随流速的变化规律,并分析了立管模型上测点的运动轨迹及其影响因素。     

Tension and Drag Forces of Flexible Risers Undergoing Vortex-Induced Vibration

This paper presents the results of an experimental investigation on the variation in the tension and the distribution of drag force coefficients along flexible risers under vortex-induced vibration (VIV) in a uniform flow for Reynolds numbers (Re) up to 2.2×10⁵. The results show that the mean tension is proportional to the square of the incoming current speed, and the tension coefficient of a flexible riser undergoing VIV can be up to 12. The mean drag force is uniformly and symmetrically distributed along the axes of the risers undergoing VIV. The corresponding drag coefficient can vary between 1.6 and 2.4 but is not a constant value of 1.2, as it is for a fixed cylinder in the absence of VIV. These experimental results are used to develop a new empirical prediction model to estimate the drag force coefficient for flexible risers undergoing VIV for Reynolds number on the order of 10⁵, which accounts for the effects of the incoming current speed, the VIV dominant modal number and the frequency.     

Experimental Study on Response Performance of VIV of A Flexible Riser with Helical Strakes

Laboratory tests were conducted on a flexible riser with and without helical strakes. The aim of the present work is to further understand the response performance of the vortex induced vibration(VIV) for a riser with helical strakes. The experiment was accomplished in the towing tank and the relative current was simulated by towing a flexible riser in one direction. Based on the modal analysis method, the displacement responses can be obtained by the measured strain. The strakes with different heights are analyzed here, and the response parameters like strain response and displacement response are studied. The experimental results show that the in-line(IL) response is as important as the cross-flow(CF) response, however, many industrial analysis methods usually ignore the IL response due to VIV. The results also indicate that the response characteristics of a bare riser can be quite distinct from that of a riser with helical strakes, and the response performance depends on the geometry on the helical strakes closely. The fatigue damage is further discussed and the results show that the fatigue damage in the CF direction is of the same order as that in the IL direction for the bare riser. However, for the riser with helical strakes, the fatigue damage in the CF direction is much smaller than that in the IL direction.     

Experimental Study on Response Performance of VIV of A Flexible Riser with Helical Strakes

Laboratory tests were conducted on a flexible riser with and without helical strakes. The aim of the present work is to further understand the response performance of the vortex induced vibration (VIV) for a riser with helical strakes. The experiment was accomplished in the towing tank and the relative current was simulated by towing a flexible riser in one direction. Based on the modal analysis method, the displacement responses can be obtained by the measured strain. The strakes with different heights are analyzed here, and the response parameters like strain response and displacement response are studied. The experimental results show that the in-line (IL) response is as important as the cross-flow (CF) response, however, many industrial analysis methods usually ignore the IL response due to VIV. The results also indicate that the response characteristics of a bare riser can be quite distinct from that of a riser with helical strakes, and the response performance depends on the geometry on the helical strakes closely. The fatigue damage is further discussed and the results show that the fatigue damage in the CF direction is of the same order as that in the IL direction for the bare riser. However, for the riser with helical strakes, the fatigue damage in the CF direction is much smaller than that in the IL direction.     

Experimental Investigation on Vortex-Induced Vibration of Steel Catenary Riser

Steel catenary riser(SCR) is the transmission device between the seabed and the floating production facilities. As developments move into deeper water, the fatigue life of the riser can become critical to the whole production system, especially due to the vortex-induced vibration(VIV), which is the key factor to operational longevity. As a result, experimental investigation about VIV of the riser was performed in a large plane pool which is 60 m long, 36 m wide and 6.5 m deep. Experiments were developed to study the influence of current speed and seabed on VIV of SCR. The results show that amplitudes of strain and response frequencies increase with the current speed both in cross-flow(CF) and in-line(IL). When the current speed is high, multi-mode response is observed in the VIV motion. The amplitudes of strain in IL direction are not much smaller than those in CF direction. The seabed has influence on the response frequencies of riser and the positions of damage for riser.     

Simulating fundamental and higher harmonic VIV of slender structures

Vortex-induced vibrations (VIV) of slender marine structures are complicated response processes, where a number of distinct frequency components might be simultaneously active. These are categorized as fundamental and higher harmonics respectively, where the latter can have a tremendous impact on the fatigue life. The present work proposes a method for time domain simulation of such multi-frequency response, by introducing a higher harmonic load term to a pre-existing semi-empirical hydrodynamic force model. Forced motion tests of a circular cylinder were simulated to experimentally and qualitatively validate the fluid-structure energy transfer. Next, the model was used to predict the response of a tension dominated riser in uniform current, for 22 velocities in the range 0.3 m/s to 2.4 m/s. The empirical input was chosen to give an average best fit with respect to the cross-flow strain measurements, which allowed dominating frequencies, fatigue damage, higher harmonics and response variability to be predicted with a high level of realism. Same set of empirical coefficients was subsequently used to predict VIV of three additional flexible pipe experiments in uniform flow, with significant differences in structural properties. The results were satisfactory for all cases, but could be improved by moderate changes to the empirical input.     

Experimental Investigation on Vortex-Induced Vibration of Steel Catenary Riser

Steel catenary riser (SCR) is the transmission device between the seabed and the floating production facilities. As developments move into deeper water, the fatigue life of the riser can become critical to the whole production system, especially due to the vortex-induced vibration (VIV), which is the key factor to operational longevity. As a result, experimental investigation about VIV of the riser was performed in a large plane pool which is 60 m long, 36 m wide and 6.5 m deep. Experiments were developed to study the influence of current speed and seabed on VIV of SCR. The results show that amplitudes of strain and response frequencies increase with the current speed both in cross-flow (CF) and in-line (IL). When the current speed is high, multi-mode response is observed in the VIV motion. The amplitudes of strain in IL direction are not much smaller than those in CF direction. The seabed has influence on the response frequencies of riser and the positions of damage for riser.     

深海悬链线立管涡激疲劳损伤研究

讨论海洋平台钢质悬链线式立管SCR(Steel Catenary Riser)的涡激疲劳损伤问题。对于悬链线立管外的流体,给出涡脱落频率和升力对立管作用的计算方法。悬链线立管采用索结构模型,进行动力学分析并利用模态叠加法对其进行动力响应分析。根据Palmgren-Miner线性累积损伤准则并结合S-N曲线,分析在不同流速下立管的涡激疲劳损伤。以工程中实际使用的1 500 m Spar海洋平台悬链线立管为例,对立管的涡激疲劳损伤进行了预报。并通过立管的参数研究,分别就立管外不同来流速度、立管壁厚、内部流体密度和柔性接头刚度对其疲劳损伤的影响进行了分析,得到了一些有意义的研究结果。     

硬悬挂钻井隔水管涡激振动特性研究

针对深水钻井过程中遭遇强台风,基于安全性考虑要求钻井平台悬挂隔水管提前撤离的问题,采用软件SHEAR7针对HYSY981钻井平台硬悬挂隔水管系统避台风撤离作业过程中,受南海一年一遇海流作用时诱发涡激振动(VIV)的情况,研究航速与悬挂长度对VIV特性的影响。研究表明,浮力块覆盖率越高,隔水管系统张力越小;浮力块分布对隔水管系统VIV响应影响较大,25%交错布置方案VIV响应最弱。隔水管并非越短越好,要综合考虑洋流剖面、隔水管配置和平台航行的影响;在不同悬挂长度及航行条件下的VIV响应,在撤离作业前应尽量避免在高流速区布置浮力单根,撤离作业时应尽量采用顺流而避免平台逆流航向。     

均匀来流下尾翼型抑振装置效果试验研究

基于控制尾流,阻止立管尾流漩涡脱落转换路径的涡激振动抑制机理,设计三角形尾翼、片状尾翼及交错尾翼等三种抑振装置。三种抑振装置分别安装于立管模型表面,立管模型采用外径为18 mm的透明有机玻璃管。通过在均匀流场中进行安装有该抑振装置的立管模型涡激振动试验,研究三种抑振装置对立管涡激振动的抑制效率,并通过与配重裸管的涡激振动数据对比,分析抑振装置对立管动力响应的影响规律。研究结果表明,三种抑振装置均取得了明显的抑振效果,与配重裸管相比,安装片状尾翼及交错尾翼的立管模型抑制效率可达90%以上,安装三角形尾翼后立管模型振动频率略有减小,而安装片状尾翼及交错尾翼的立管模型没有明显的主导频率。     

VIV response of a long flexible riser fitted with strakes in uniform and linearly sheared currents

An experimental investigation was conducted on a flexible riser with and without various strake arrangements. The aim of the present work was to further improve the understanding of the response performance of the vortex-induced vibration (VIV) of a riser with helical strakes. Two current profiles, including uniform and linearly sheared flows, were simulated. The uniform current was simulated by towing the riser model in one direction using the towing carriage, and the linearly sheared current was simulated by fixing one end of the riser and using a driven cantilever to traverse a circular arc. Based on the modal superposition method, the displacement responses were obtained from the measured strain. Strakes with different heights and pitches were analysed, and response parameters such as the displacement response and fatigue damage were studied. The results of the bare model test show that the lock-in phenomenon displays multi-order characteristics, and the VIV displacement decreases with an increased order of the lock-in regime. The results of the straked model test indicate that the response characteristics of a bare riser can be quite distinct from those of a riser with helical strakes, and the response performance depends closely on the geometry of the strake configuration.     

Time domain prediction approach for cross-flow VIV induced fatigue damage of steel catenary riser near touchdown point

Previous steel catenary riser (SCR) models targeted for VIV prediction are truncated at touchdown point (TDP) where simple constrain and rotation stiffness are generally applied. In this study, a time domain approach accounting for the SCR–soil interaction is proposed to predict the cross-flow (CF) VIV induced fatigue damage of a SCR near TDP. The hydrodynamic force is simulated based on the forced vibration test data as a function of the non-dimensional amplitude and frequency, and an empirical damping model. When the non-dimensional frequency associated with the calculated frequency falls in the excitation region, the natural frequency closer to the frequency corresponding to the maximum excitation force is taken to be the dominant frequency, and applied to obtain the excitation force. The SCR–soil interaction model takes into account the trench shape, and the mobilization and release of the soil suction. Fatigue damage is linearly accumulated by using the rain-flow counting methodology. To validate the proposed models, simulation for a riser model test is carried out, and the envelopes of RMS displacement, curvature, and fatigue damage are compared. Further works focus on the sensitivity of VIV induced fatigue damage near TDP to the seabed parameters, such as mudline shear strength, shear strength gradient and soil suction, and some conclusions are obtained.     

Simplified Prediction Model for Vortex-Induced Vibrations of Top Tensioned Risers

According to the characteristics of deepwater top tensioned risers, a simplified model is presented to predict the multi-modal response of vortex-induced vibration （VIV） in non-uniform flow based on energy equilibrium theory and the exporimental data from VIV self-excited and forced oscillations of rigid cylinders. The response amplitude of each mode is determined by a balance between the energy fed into the riser over the lock-in regions and the energy dissipated by the fluid damping over the remainders. Compared with the previous prediction models, this method can take fully account of the intrinsic nature of VIV for low mass ratio structures on lock-in regions, added mass and nonlinear fluid damping effect, etc. Moreover, it is the first time to propose the accurate calculating procedure for VIV amplitude correction factor by solving energy equilibrium equation and a closed form solution is presented for the case of a riser of uniform mass and cross-section oscillating in a uniform flow. The predicted values show a reasonable agreement with VIV experiments of riser models in stepped and sheared currents.     

Experimental investigation of the effects of the coverage of helical strakes on the vortex-induced vibration response of a flexible riser

The effects of different helical strake coverage on the vortex-induced vibration (VIV) of a model flexible riser were studied experimentally, with the aim of further improving the understanding of VIV responses. Uniform and linearly sheared currents were simulated to study response parameters such as non-dimensional displacement, fatigue damage, suppression efficiency, and the comprehensive evaluation is further studied. Test results of the bare model for a uniform current showed that the behavior of both the standing wave and traveling wave dominated VIV displacement. However, for a linearly sheared current, traveling wave behavior dominated VIV displacement in the high-velocity range. The results of the straked model tests indicated that the response was strongly dependent upon the amount of coverage of helical strakes. The flexible riser with 75% strake coverage gave the best comprehensive evaluation in a uniform current, and 50% strake coverage gave the best comprehensive evaluation in a linearly sheared current.     

An Experimental Study on Dynamics Features of Three Side-by-Side Flexible Risers Undergoing Vortex-Induced Vibrations in A Uniform Flow

A vortex-induced vibration(VIV) experiment on three side-by-side risers subjected to a uniform flow was carried out in a combined wave-current flume. The dynamic features of interference effect on three side-by-side risers were investigated by varying fluid velocity and inter-riser spacing. The distributions of dimensionless displacement,dominant frequency, and displacement trajectory of the model risers were measured using mode decomposition and wavelet transform techniques. The coupled interference of inter-riser fluid to adjacent risers at different spacings was disclosed by introducing the "interference ratio" concept. The results show that at spacings smaller than 6.0 D, the three model risers display appreciable deviations in their displacement responses in cross-flow or in-line direction,attributable to the strong proximity disturbance and wake interference between the risers. When the spacing is increased to 8.0 D, wake interference still makes great difference to the dynamic response of the risers in both directions. As reduced velocity increases, the three risers show higher agreement with an isolated riser in overall dominant vibration frequency in CF direction than that in IL direction at all spacings and the side risers, although symmetrically placed, do not vibrate symmetrically, as a result of the steady deflection of clearance flow within the riser group. Interference effect results in a remarkable unsteady mode competition within the risers; quantitation of the interference levels for the three risers at different spacings with interference ratio revealed that under low flow velocities and large spacing ratios, clearance flow constitutes a non-neglectable interferer for three side-by-side risers.     

基于可靠性的海洋立管疲劳安全系数研究

综合考虑了立管疲劳安全系数取值的相关因素——立管的安全等级、设计寿命、检验周期、载荷和损伤计算方法等的不确定性,提出了基于可靠度的疲劳安全系数确定方法,筛选了用于计算波致疲劳和VIV(涡激振动)疲劳的随机变量,给出了立管波致疲劳与VIV疲劳安全系数的计算流程,并以某SCR(钢悬链线立管)为例进行了安全系数计算。结果表明,该方法的计算结果优于传统的安全系数确定方法,尤其适合于特殊工程方案或新颖设计的立管疲劳校核。     

Cross-Flow VIV-Induced Fatigue Damage of Deepwater Steel Catenary Riser at Touch-Down Point简

A prediction model of the deepwater steel catenary riser VIV is proposed based on the forced oscillation test data, taking into account the riser-seafloor interaction for the cross-flow VIV-induced fatigue damage at touch-down point （TDP）. The model will give more reasonable simulation of SCR response near TDP than the previous pinned truncation model. In the present model, the hysteretic riser-soil interaction model is simplified as the linear spring and damper to simulate the seafloor, and the damping is obtained according to the dissipative power during one periodic riser-soil interaction. In order to validate the model, the comparison with the field measurement and the results predicted by Shear 7 program of a full-scale steel catenary riser is carried out. The main induced modes, mode frequencies and response amplitude are in a good agreement. Furthermore, the parametric studies are carried out to broaden the understanding of the fatigue damage sensitivity to the upper end in-plane offset and seabed characteristics. In addition, the fatigue stress comparison at TDP between the truncation riser model and the present full riser model shows that the existence of touch-down zones is very important for the fatigue damage assessment of steel catenary riser at TDP.     

Centrifuge modelling of SCR vertical motion at touchdown zone

Steel catenary risers (SCR) connect seabed pipelines and flow lines to floating structures used for oil and gas production in deep waters. Waves and currents induce motions of the structure and the risers. The repeated motions of the risers at the touchdown zone in turn induce loads on the seabed soil and might eventually cause fatigue damage to the risers. The analysis of riser fatigue damage is heavily dependent on the soil model. Soil behaviour at touchdown zone such as soil remoulding, stiffness degradation and deformation of the seabed at the touchdown zone further complicate the accurate assessment of riser fatigue damage, which is currently not appropriately quantified in existing design methods. This paper presents centrifuge model tests simulating the repeated vertical movement of a length of riser on clay seabed with increasing undrained shear strength with depth. During the tests, the pipe was subject to cyclic motion over fixed vertical displacement amplitude from an invert embedment of 0.5-3.5 pipe diameters into the soil. The test results show a significant progressive degradation of soil strength and diminution of excess pore water pressure with increasing number of riser penetration/uplift cycle. In view of the different types of environment loadings experienced by floating platforms and various soil conditions, tests were also conducted to investigate the effect of soil strength, riser displacement rate and loading mode on riser-soil interaction during repetitive penetration/uplift motion of the riser.     

Laboratory Measurements of Vortex- and Wake-Induced Vibrations of A Tandem Arrangement of Two Flexible Risers

The dynamic response of two flexible model risers in tandem arrangement immersed in a stepped current was analyzed. The risers, with an external diameter of 20 mm and a total length of 6200 mm, had an aspect ratio of 310. They were hinged to the support structure at the center-to-center distances away 3?12 times the external diameter. The top 1200 mm was exposed to a uniform current at a speed which was up to 0.9 m/s (the Reynolds number was 18000) and the rest in still water. The dynamic responses, which were obtained through the Fiber Bragg Grating strain gauges mounted on the surface, were analyzed by studying the cross-flow amplitudes and modal weights. The cross-flow vibration were observed up to the third mode, and the modal transformation from the second mode to the third mode was clearly observed. The experiment confirmed that the typical vortex-induced vibration (VIV) had occurred on the up-stream riser. But for the down-stream riser, the main excitation mechanism was wake-induced vibration (WIV). The modal transformation of WIV was more complex than that of VIV, which might be helpful for other researchers to study the interference effect.