Stochastic control of wave energy converters for optimal power absorption with constrained control force

This paper presents an analytical solution derived for optimal control of the power take-off of a single-degree of freedom heave point absorber with constraints on the control force. The optimal control law turns out to be noncausal with a functional dependence on future velocities. To handle this problem, an algorithm for predicting future velocities is derived. Based on the solution the mean (time-averaged) absorbed power in a given sea-state is calculated. The performance of the indicated controller in terms of the mean absorbed power is close to the optimal value obtained by nonlinear programming and better than a controller with feedback from the present displacement, velocity and acceleration, and with optimized gain factors.     

Phase control through load control of oscillating-body wave energy converters with hydraulic PTO system

Oscillating bodies constitute an important class of wave energy converters, especially for offshore deployment. Phase control by latching has been proposed in the 1970s to enhance the wave energy absorption by oscillating bodies (especially the so-called point absorbers). Although this has been shown to be potentially capable of substantially increasing the amount of absorbed energy, the practical implementation in real irregular waves of optimum phase control has met with theoretical and practical difficulties that have not been satisfactorily overcome. The present paper addresses the case of oscillating-body converters equipped with a high-pressure hydraulic power take-off mechanism (PTO) that provides a natural way of achieving latching: the body remains stationary for as long as the hydrodynamic forces on its wetted surface are unable to overcome the resisting force (gas pressure difference times cross-sectional area of the ram) introduced by the hydraulic PTO system. A method of achieving sub-optimal phase-control is developed, based on the theoretical time-domain modelling of a single-degree of freedom oscillating body in regular and irregular waves, by adequately delaying the release of the body in order to approximately bring into phase the body velocity and the diffraction (or excitation) force on the body, and in this way get closer to the well-known optimal condition derived from frequency-domain analysis for an oscillating body in regular waves.     

双浮子点吸收式波能转换装置参数研究

点吸收式波能转换装置是具有较好应用前景的一种波浪能开发利用装置,其参数设计直接影响到波浪能开发利用的可行性与有效性.作者针对青岛斋堂岛目标海域海况,通过数值模拟首先应用单因素敏感性分析法分析了双浮子点吸收式波能转换装置的结构尺寸、锚固形式、波流夹角、PTO阻尼、PTO刚度等参数对装置俘能功率的独立影响规律.之后考虑多参...     

An efficient hybrid integral-equation method for point-absorber wave energy converters with a vertical axis of symmetry

To assist in the prototyping and controller design of point-absorber wave energy converters (WECs), an easy-to-implement hybrid integral-equation method is presented for computing the frequency-domain hydrodynamic properties of bodies with a vertical axis of symmetry in waves. The current hybrid method decomposes the flow domain into two parts: an inner domain containing the body and an outer domain extending to infinity. The solution in the inner domain is computed using the boundary-element method, and the outer-domain solution is expressed using eigenfunctions. Proper matching at the domain boundary is achieved by enforcing continuity of velocity potential and its normal derivative. Body symmetry allows efficient computation using ring sources in the inner domain. The current method is successfully applied to three different body geometries including a vertical truncated floating cylinder, the McIver toroid, and the coaxial-cylinder WEC being developed in the authors’ laboratory. In particular, the current results indicate that, by replacing the flat bottom of the coaxial-cylinder WEC with the Berkeley-Wedge (BW) shape, viscous effect can be significantly reduced with only minor negative impact on wave-exciting force, thus increasing WEC efficiency. Finally, by comparing to experimental measurements, the current method is demonstrated to accurately predict the heave added mass and wave-exciting force on the coaxial-cylinder WEC with BW geometry. If a viscous damping correction factor is used, the heave motion amplitude can also be accurately computed.     

Modelling of a wave energy converter array with a nonlinear power take-off system in the frequency domain

This paper presents a nonlinear frequency domain model and uses this to assess the performance of a wave energy converter (WEC) array with a nonlinear power take-off (PTO). In this model, the nonlinear PTO forces are approximated by a truncated Fourier series, while the dynamics of the WEC array are described by a set of linear motion equations in the frequency domain, and the hydrodynamic coefficients are obtained with the boundary element method. A single heave absorber is firstly investigated to establish the accuracy of the new model in capturing the nonlinear behaviour of the pumping system. Subsequently, simulations of a 2D array with 18 WECs and a pillar in the centre (representing the tower of a wind turbine) are carried out to understand wave interference effects. Several optimisation strategies are proposed to improve the overall performance of the WEC array. These results demonstrate a computationally effective method for accounting for nonlinear effects in large WEC arrays. The proposed approach may potentially be applied for developing control algorithms for the adaptability of a 2D array to incoming wave excitation.     

Spectral modelling of wave energy converters

A spectral model suitable for the representation of wave energy converters is developed. A spectral model is an extension of a frequency-domain model that allows inclusion of non-linear forces and thereby provides improved estimates of wave energy converter performance, without the high computational cost of a time-domain model. The suitability and accuracy of a spectral model representation is demonstrated for a flap-type wave energy converter, by modelling the effect of vortex shedding and large amplitudes of motion. The development of a spectral model of wave energy converters also means that they can be represented in spectral wave models and included explicitly in software tools such as SWAN or Mike21 SW. This means that tools familiar to the industry could be used to determine the environmental impact and energy yield of wave farms efficiently.     

Performance investigation of a two-raft-type wave energy converter with hydraulic power take-off unit

Raft-type wave energy converter (WEC) is a multi-mode wave energy conversion device, using the relative pitch motion to drive its hydraulic power take-off (PTO) units for capturing energy from the ocean waves. The hydraulic PTO unit as its energy conversion module plays a significant role in storing large qualities of energy and making the output power smooth. However, most of the previous investigations on the raft-type WECs treat the hydraulic PTO unit as a linear PTO unit and do not consider the dynamics of the hydraulic circuit and components in their investigations. This paper is related to a two-raft-type WEC consisting of two hinged rafts and a hydraulic PTO unit. The aim of this paper is to make an understanding of the dynamics of the hydraulic PTO unit and how these affect the performance of the two-raft-type WEC. Therefore, a combined hydrodynamic and hydraulic PTO unit model is proposed to investigate and optimize the performance of the two-raft-type WEC; and based on the simulation of the combined model, the relationships between the optimal power capture ability, the optimal magnitude of the hydraulic PTO force and the wave states are numerically revealed. Results show that an approximately square wave type hydraulic PTO force is produced by the hydraulic PTO unit, which causes the performance of the two-raft-type WEC not to be sinusoidal and the energy capturing manner different from that of the device using a linear PTO unit; moreover, there is an optimal magnitude of the hydraulic PTO force for obtaining an optimal power capture ability, which can be achieved by adjusting the parameters of the hydraulic PTO unit; in regular waves, the optimal power capture ability as well as the optimal magnitude of the hydraulic PTO force normalized by the wave height presents little relationship with the wave height, mainly depends on the wave period; in irregular waves, the trends of the optimal power capture ability and the normalized optimal magnitude of the hydraulic PTO force against the peak wave periods at different significant wave heights are generally identical and show a good correlation. All means that the hydraulic PTO unit of the two-raft-type WEC can be tuned to the wave states, and these would provide a valuable guidance for the optimal design of its hydraulic PTO unit.     

Wave groupiness and spectral bandwidth as relevant parameters for the performance assessment of wave energy converters

To date the estimation of long-term wave energy production at a given deployment site has commonly been limited to a consideration of the significant wave height H_s and mean energy period T_e. This paper addresses the sensitivity of power production from wave energy converters to the wave groupiness and spectral bandwidth of sea states. Linear and non-linear systems are implemented to simulate the response of converters equipped with realistic power take-off devices in real sea states. It is shown in particular that, when the converters are not much sensitive to wave directionality, the bandwidth characteristic is appropriate to complete the set of overall wave parameters describing the sea state for the purpose of estimating wave energy production.     

Wave energy conversion under constrained wave-by-wave impedance matching with amplitude and phase-match limits

This paper investigates an approach to limit the fullness of ‘tuning’ provided by wave-by-wave impedance matching control of wave energy devices in irregular waves. A single analytical formulation based on the Lagrange multiplier approach of Evans [1] is used to limit the velocity amplitude while also limiting the closeness of the phase match between velocity and exciting force. The paper studies the effect of the present technique in concurrently limiting the device velocity and the required control/actuation force. Time domain application requires wave-profile prediction, which here is based on a deterministic propagation model. Also examined in the time domain is the effect of possible violation of the displacement constraint, which for many designs implies impacts at hard stops within the power take-off mechanism. Time domain simulations are carried out for a 2-body axisymmetric converter (with physical end-stops) in sea states reported for a site off the US east coast. It is found that the approach leads to effective power conversion in the less energetic sea states, while as desired, considerable muting of the optimal response is found in the larger sea states. Under the assumptions of this work, the end-stop collisions are found to have a minor effect on the power conversion. The present approach could be used to guide the design of power take-off systems so that their displacement stroke, maximum force, and resistive and reactive power limits are well-matched to the achievable performance of a given controlled primary energy converter.     

Design of a hydraulic power take-off system for the wave energy device with an inverse pendulum

This paper describes a dual-stroke acting hydraulic power take-off （PTO） system employed in the wave energy converter （WEC） with an inverse pendulum. The hydraulic PTO converts slow irregular reciprocating wave motions to relatively smooth, fast rotation of an electrical generator. The design of the hydraulic PTO system and its control are critical to maximize the generated power. A time domain simulation study and the laboratory experiment of the full-scale beach test are presented. The results of the simulation and laboratory experiments including their comparison at full-scale are also presented, which have validated the rationality of the design and the reliability of some key components of the prototype of the WEC with an inverse pendulum with the dual-stroke acting hydraulic PTO system.     

Farm size comparison with analytical model of linear generator wave energy converters

Ocean wave energy is an emerging kind of renewable energy, and several energy conversion methods are available today. One solution is to connect a buoy to a linear generator. Such units are quite small (10–100 kW), and farm solutions are suggested to increase power production. This paper shows the results from small farm simulations where the translator motion is varied for the generators in the farm.Simulations with five and 10 units show that power fluctuations decrease with an increasing number of generators.     

Dynamic analysis of wave energy converter by incorporating the effect of hydraulic transmission lines

A heaving-buoy wave energy converter equipped with hydraulic power take-off is studied in this paper. This wave energy converter system is divided into five subsystems: a heaving buoy, hydraulic pump, pipelines, non-return check valves and a hydraulic motor combined with an electric generator. A dynamic model was developed by considering the interactions between the subsystems in a state space form. The transient pressures caused by starting/stopping the buoy or closing/opening the check valves were predicted numerically using the established model. The simulation results show that transmission line dynamics play a dominant role in the studied wave energy converter system. The length of the pipeline will not only affect the amplitude of the transient pressures but also affect the converted power. The variation of the time-averaged converted electric power with the pipeline length is estimated using the simulation method for the buoy exposed to one irregular sea state. Finally, it is suggested how reduced power efficiency due to the pipelines may be ameliorated.     

The effect of water depth on the performance of a small surging wave energy converter

The effect of water depth on the performance of a small surging wave energy converter (WEC) is investigated analytically, numerically and experimentally. It is shown that although the average annual incident wave power is significantly reduced by water depth, a large proportion of this reduction is due to the dissipation of highly energetic, but largely unexploitable seas. It is also shown that the power capture is related more closely to incident wave force than incident wave power. Experimental results demonstrate that both the surge wave force and power capture of a flap-type WEC increase in shallow water.     

OWC wave energy devices with air flow control

A theoretical model is developed to simulate the energy conversion, from wave to turbine shaft, of an oscillating-water-column (OWC) plant equipped with a Wells air-turbine and with a valve (in series or in parallel with the turbine) for air-flow control. Numerical simulations show that the use of a control valve, by preventing or reducing the aerodynamic stall losses at the turbine rotor blades, may provide a way of substantially increasing the amount of energy produced by the plant, particularly at the higher incident wave power levels. From the hydrodynamic point of view, a by-pass valve or a throttle valve should be used depending on whether the wave energy absorbing system is over-damped or under-damped by the turbine.     

Investigation on the energy absorption performance of a fixed-bottom pressure-differential wave energy converter

In this article, we investigate the energy absorption performance of a fixed-bottom pressure-differential wave energy converter. Two versions of the technology are considered: one has the moving surfaces on the bottom of the air chambers whereas the other has the moving surfaces on the top. We developed numerical models in the frequency domain, thereby enabling the power absorption of the two versions of the device to be assessed. It is observed that the moving surfaces on the top allow for easier tuning of the natural period of the system. Taking into account stroke limitations, the design is optimized. Results indicate that the pressure-differential wave energy converter is a highly efficient technology both with respect to energy absorption and selected economic performance indicators.     

垂荡式波浪能装置运动模型数值分析

垂荡式波浪能装置在海洋可再生能源开发中被广泛应用,通过浮子与摇杆在垂荡方向的相对运动吸收波浪能。在以往相关的运动预报数值分析中,通常基于微幅波假设,仅考虑浮子与摇杆在垂荡方向的运动,忽略摇杆其他自由度运动。建立并求解了垂荡式波浪能装置的非线性联合运动方程组,分析垂荡式波浪能装置的波浪载荷、浮子与平台连接处的受力情况。数值计算系统的运动响应,并将计算结果与已有的试验数据进行比较验证,结果表明数值模拟的垂荡式波能装置的运动响应与试验结果相符合。最后,应用本计算方法分析PTO(power take-off)参数对波能装置发电性能的影响。     

Wave tank and bench-top control testing of a wave energy converter

An increasing number of experiments are being conducted to study the design and performance of wave energy converters. Often in these tests, a real-time realization of prospective control algorithms is applied in order to assess and optimize energy absorption as well as other factors. This paper details the design and execution of an experiment for evaluating the capability of a model-scale WEC to execute basic control algorithms. Model-scale hardware, system, and experimental design are considered, with a focus on providing an experimental setup capable of meeting the dynamic requirements of a control system. To more efficiently execute such tests, a dry bench testing method is proposed and utilized to allow for controller tuning and to give an initial assessment of controller performance; this is followed by wave tank testing. The trends from the dry bench test and wave tank test results show good agreement with theory and confirm the ability of a relatively simple feedback controller to substantially improve energy absorption. Additionally, the dry bench testing approach is shown to be an effective and efficient means of designing and testing both controllers and actuator systems for wave energy converters.     

Near-optimal control of a wave energy device in irregular waves with deterministic-model driven incident wave prediction

This paper investigates wave-by-wave control of a wave energy converter using incident wave prediction based on up-wave surface elevation measurement. The goal of control is to approach the hydrodynamically optimum velocity leading to optimum power absorption. This work aims to study the gains in energy conversion from a deterministic wave propagation model that accounts for a range of group velocities in deriving the prediction. The up-wave measurement distance is assumed to be small enough to allow a deterministic propagation model, and further, both wave propagation and device response are assumed to be linear. For deep water conditions and long-crested waves, the propagation process is also described using an impulse response function (e.g. [1]). Approximate low and high frequency limits for realistic band-limited spectra are used to compute the corresponding group velocity limits. The prediction time into the future is based on the device impulse response function needed for the evaluation of the control force. The up-wave distance and the duration of measurement are then determined using the group velocity limits above.A 2-body axisymmetric heaving device is considered, for which power capture is through the relative heave oscillation between the two co-axial bodies. The power take-off is assumed to be linear and ideal as well as capable of applying the necessary resistive and reactive load components on the relative heave oscillation. The predicted wave profile is used along with device impulse response functions to compute the actuator force components at each instant. Calculations are carried out in irregular waves generated using a number of uni-modal wave spectra over a range of energy periods and significant wave heights. Results are compared with previous studies based on the use of instantaneous up-wave wave-profile measurements, both without and with oscillation constraints imposed. Considerable improvements in power capture are observed with the present approach over the range of wave conditions studied.     

Constrained near-optimal control of a wave energy converter in three oscillation modes

This paper investigates the performance of a small axisymmetric buoy under wave-by-wave near optimal control in surge, heave, and pitch modes in long-crested irregular waves. Wave prediction is obtained using a deterministic propagation model. The paper describes the overall formulation leading up to the derivation of the feedforward control forces in surge and heave, and the control moment in pitch. The radiation coupling between surge and pitch modes is accounted for in the model. Actuation is relative to deeply submerged reaction masses. Heave oscillations are constrained by the swept-volume limit. Oscillation constraints are also applied on the surge and pitch oscillations. The paper discusses time-domain simulations for an irregular wave input with and without the present control. Also discussed are results obtained over a range of irregular wave conditions derived for energy periods from 7 s to 17 s, and a significant wave height of 1 m. It is found that, while the gains in power capture enabled by the present control are significant, the actuation forces are also very large, given the small size of the buoy. Further, due to the small size, heave is found to be the dominant contributor to power capture, with relatively modest contributions from surge and pitch.