A bounding surface model for anisotropically overconsolidated clay incorporating thermodynamics admissible rotational hardening rule

A bounding surface model is formulated to simulate the behavior of clays that are subject to an anisotropic consolidation stress history. Conventional rotational hardening is revisited from the perspective of thermodynamics. As the free energy cannot be accumulated infinitely upon critical state failure, the deviatoric back stress must vanish. This requires the rotated yield surface to be turned back to eventually align on the hydrostatic axis in the stress plane. Noting that most of the previous propositions violate this restriction, an innovative rotational hardening rule is formulated that is thermodynamically admissible. The bounding surface framework that employs the modified yield surface is applied to simulate elastoplastic deformations for overconsolidated clays, with which the overprediction of strength on the “dry” side can be greatly improved with reasonable results. Other important features, including contractive or dilative response and hardening or softening behavior, can also be well-captured. It has been shown that the model can simulate three types of reconstituted clays that are sheared with initial conditions over a wide range of anisotropic consolidation stress ratios and overconsolidation ratios under both triaxial undrained and drained conditions. Limitations and potential improvement of the model regarding the fabric anisotropy at critical state have been discussed.     

An anisotropic elastoplastic model for soft clays based on logarithmic contractancy

A new constitutive model for soft structured clays is developed based on an existing model called S‐CLAY1S, which is a Cam clay type model that accounts for anisotropy and destructuration. The new model (E‐SCLAY1S) uses the framework of logarithmic contractancy to introduce a new parameter that controls the shape of the yield surface as well as the plastic potential (as an assumed associated flow rule is applied). This new parameter can be used to fit the coefficient of earth pressure at rest, the undrained shear strength or the stiffness under shearing stress paths predicted by the model. The improvement to previous constitutive models that account for soil fabric and bonding is formulated within the contractancy framework such that the model predicts the uniqueness of the critical state line and its slope is independent of the contractancy parameter. Good agreement has been found between the model predictions and published laboratory results for triaxial compression tests. An important finding is that the contractancy parameter, and consequently the shape of the yield surface, seems to change with the degree of anisotropy; however, further study is required to investigate this response. From published data, the yield surface for isotropically consolidated clays seems ‘bullet’ or ‘almond’ shaped, similar to that of the Cam clay model; while for anisotropically consolidated clays, the yield surface is more elliptical, like a rotated and distorted modified Cam clay yield surface. © 2015 The Authors. International Journal for Numerical and Analytical Methods in Geomechanics published by John Wiley & Sons Ltd.     

Simulation of yielding and stress–stain behavior of shanghai soft clay

In this paper, a simple bounding surface plasticity model is used to reproduce the yielding and stress–strain behavior of the structured soft clay found at Shanghai of China. A series of undrained triaxial tests and drained stress probe tests under isotropic and anisotropic consolidation modes were performed on undisturbed samples of Shanghai soft clay to study the yielding characteristics. The degradation of the clay structure is modeled with an internal variable that allows the size of the bounding surface to decay with accumulated plastic strain. An anisotropic tensor and rotational hardening law are introduced to reflect the initial anisotropy and the evolution of anisotropy. Combined with the isotropic hardening rule, the rotational hardening rule and the degradation law are incorporated into the bounding surface formulation with an associated flow rule. Validity of the model is verified by the undrained isotropic and anisotropic triaxial test and drained stress probe test results for Shanghai soft clay. The effects of stress anisotropy and loss of structure are well captured by the model.     

A destructuration theory and its application to SANICLAY model

Many natural clays have an undisturbed shear strength in excess of the remoulded strength. Destructuration modeling provides a means to account for such sensitivity in a constitutive model. This paper extends the SANICLAY model to include destructuration. Two distinct types of destructuration are considered: isotropic and frictional. The former is a concept already presented in relation to other models and in essence constitutes a mechanism of isotropic softening of the yield surface with destructuration. The latter refers to the reduction of the critical stress ratio reflecting the effect of destructuration on the friction angle, and is believed to be a novel proposition. Both the types depend on a measure of destructuration rate expressed in terms of combined plastic volumetric and deviatoric strain rates. The SANICLAY model itself is generalized from its previous form by additional dependence of the yield surface on the third isotropic stress invariant. Such a generalization allows to obtain as particular cases simplified model versions of lower complexity including one with a single surface and associative flow rule, by simply setting accordingly parameters of the generalized version. A detailed calibration procedure of the relatively few model constants is presented, and the performance of three versions of the model, in descending order of complexity, is validated by comparison of simulations to various data for oedometric consolidation followed by triaxial undrained compression and extension tests on two structured clays. Copyright © 2009 John Wiley & Sons, Ltd.     

考虑饱和黏土初始各向异性的循环边界面塑性模型

天然土体的初始各向异性通常可对其后继循环特性产生显著影响。现有考虑循环载荷作用的土体弹塑性模型,往往采用类似修正剑桥模型的椭圆形屈服面,已有研究表明,该椭圆形屈服面因其拉伸弹性区域偏大,针对天然K0固结状态的土体,其计算精度较差。基于新近提出的广义各向同性硬化准则,在边界面方程中引入初始各向异性张量,并采用空间滑动面破坏准则（SMP）的变换应力法,建立了能考虑饱和黏土初始各向异性的循环边界面塑性模型。分别针对等压和偏压固结的饱和黏土静、动三轴试验进行模拟,结果表明,该模型能合理反映土体的初始各向异性及其后继循环动力特性。     

Numerical modeling of changes in anisotropy during liquefaction using a generalized constitutive model

A constitutive model with rotation hardening was generalized from the triaxial compression state to a general stress state. With the generalized model, numerical simulations of cyclic and monotonic undrained triaxial tests were conducted to reproduce the phenomenon of continuous, orderly and rapid changes in anisotropy during liquefaction. The simulated results demonstrated that when sand enters the liquefaction stage, the yield surface in the stress space rotates quickly, causing continuous and rapid changes in anisotropy. Through comparison of the simulated and experimental results, the generalized constitutive model was shown to be able to capture the fundamental behaviors of sand demonstrated by the experimental data, and the rotational hardening rule adopted in the generalized model was proven suitable for describing the continuous, orderly and rapid changes in anisotropy that occur during liquefaction.     

各向异性弹黏塑性模型在ABAQUS中的研发

通过将Perzyna过应力理论与临界状态理论相结合,并引入Wheeler旋转硬化法则,提出一个能描述土体初始各向异性及应力诱发各向异性的三维弹黏塑性本构模型。模型考虑流变发生的下限,在三维应力空间,模型存在形状相似的静屈服面及动态加载面。采用缩放形式的幂函数。本构模型数值算法采用回映算法,借助ABAQUS软件UMAT子程序接口实现。并通过对三轴不排水蠕变试验的模拟,确定合适的积分步长。此后,分别对三轴不排水蠕变试验及常应变率三轴不排水剪切试验进行了模拟。模拟中通过设置不同参数值,可将模型退化为各向同性模型,并对这两种模拟结果进行了比较。模拟结果表明：(1) 对于三轴不排水蠕变,在低剪应力水平下,各向同性模型和各向异性模型模拟的结果相差不大,而在高剪应力水平下,各向异性模型模拟结果更接近试验结果;(2) 对于常应变率加载试验的模拟,模型合理反映了土体不排水强度随着加载速率的增大而增大现象。     

Undrained cavity expansion in anisotropic soils with isotropic and frictional destructuration

This paper proposes a semi-analytical solution of undrained cylindrical cavity expansion in anisotropic soils with both isotropic and frictional destructuration. The rigorous derivation based on the general form of the SANICLAY model with destructuration is provided following a standardized solving procedure, and the features of anisotropy and structuration are then invoked in the cavity expansion solution by adopting the non-associated hierarchical model. Cavity expansion tests in both structured and unstructured clays with various overconsolidation ratio are conducted to investigate the evolutions of effective stresses, excess pore pressure, anisotropic parameters and structuration factors during cylindrical expansion. The results show that the effective stresses at the cavity wall are lower after expansion and the cavity excess pore pressure is oppositely higher in structured clays with slightly smaller plastic regions. The evolutions of anisotropy for structured clays appear to follow similar patterns to unstructured cases, whereas the degree of anisotropy is further developed with gradual loss of inter-particle bonds. Finally, the proposed solution is applied to predict the limit pressure of pressuremeter tests in Bothkennar clay, showing its ability for interpretation of in situ testing data in natural structured clays.

     

Delayed plastic model for time‐dependent behaviour of materials

A delayed plastic model, based on the theory of plasticity, is proposed to represent the time‐dependent behaviour of materials. It is assumed in this model that the stress can lie outside the yield surface and the conjugate stress called static stress is defined on the yield surface. The stress–strain relation is calculated based on the plastic theory embedding the static stress. Thus, the stress–strain relation of the model practically corresponds to that of the inviscid elastoplastic model under fairly low rate deformation. The delayed plastic model is coupled with the Cam‐clay model for normally consolidated clays. The performance of the model is then examined by comparing the model predictions with reported time‐dependent behaviour of clays under undrained triaxial conditions. It is shown that the model is capable of predicting the effect of strain rate during undrained shear and the undrained creep behaviour including creep rupture. Copyright © 2001 John Wiley & Sons, Ltd.     

Kinematic hardening plasticity formulation of small strain behaviour of soils

An objective of this paper is to demonstrate that the small strain model developed by the authors can be incorporated into the conventional kinematic hardening plasticity framework to predict pre‐failure defor mations. The constitutive model described in this paper is constituted by three elliptical yield surfaces in triaxial stress space. Two inner surfaces are rotated ellipses of the same shape, representing the boundaries of the linear elastic and small strain regions, while the third surface is the modified Cam clay large‐scale yield surface. Within the linear elastic region, the soil behaviour is elastic with cross‐coupling between the shear and volumetric stress–strain components. Within the small strain region, the soil behaviour is elasto‐plastic, described by the kinematic hardening rule with an infinite number of loading surfaces defined by the incremental energy criterion. Within the large‐scale yield surface, the soil behaviour is elasto‐plastic, described by kinematic and isotropic hardening of the small strain region boundary. Since the yield surfaces have different shapes, the uniqueness of the plastic loading condition imposes a restriction on the ratio between their semi‐diameters. The model requires 12 parameters, which can be determined from a single consolidated undrained triaxial compression test. Copyright © 2000 John Wiley & Sons, Ltd.     

A critical state model for overconsolidated structured clays

This paper presents a generalised critical state model with the bounding surface theory for simulating the stress–strain behaviour of overconsolidated structured clays. The model is formulated based on the framework of the Structured Cam Clay (SCC) model and is designated as the Modified Structured Cam Clay with Bounding Surface Theory (MSCC-B) model. The hardening and destructuring processes for structured clays in the overconsolidated state can be described by the proposed model. The image stress point defined by the radial mapping rule is used to determine the plastic hardening modulus, which varies along loading paths. A new proposed parameter h, which depends on the material characteristics, is introduced into the plastic hardening modulus equation to take the soil behaviour into account in the overconsolidated state. The MSCC-B model is finally evaluated in light of the model performance by comparisons with the measured data of both naturally and artificially structured clays under compression and shearing tests. From the comparisons, it is found that the MSCC-B model gives reasonable good simulations of mechanical response of structured clays in both drained and undrained conditions. With its simplicity and performance, the MSCC-B model is regarded as a practical geotechnical model for implementation in numerical analysis.     

Evaluation of an anisotropic elastoplastic–viscoplastic bounding surface model for clays

An anisotropic time-dependent bounding surface model for clays is developed by generalizing a previous time-independent model that adopts a flexible bounding surface. It is based on the framework for coupled elastoplasticity–viscoplasticity for clays and Perzyna’s overstress theory. Three viscoplastic parameters were introduced and explained in detail. The model was validated against undrained creep tests for both isotropically and anisotropically consolidated clays, undrained and drained stress relaxation tests on some undisturbed clays, and undrained triaxial tests with varying strain rates on natural Hong Kong marine deposit clay. The general agreement between the model simulations and test results was satisfactory. The varying effects of lower-level parameters were discussed on the undrained multistage stress relaxation response for normally consolidated soils which had been ignored in literature. The flexibility of the model in capturing the shear strengths, which is the unique feature of the current model, was shown in the simulations of time-dependent triaxial tests on Taipei silty clay. All the simulations show that the proposed model is a relatively practical model considering both anisotropy and time dependency of clays.     

CASM: a unified state parameter model for clay and sand

The purpose of this paper is to present a simple, unified critical state constitutive model for both clay and sand. The model, called CASM (Clay And Sand Model), is formulated in terms of the state parameter that is defined as the vertical distance between current state (v, p′) and the critical state line in v–ln p′ space. The paper first shows that the standard Cam-clay models (i.e. the original and modified Cam-clay models) can be reformulated in terms of the state parameter. Although the standard Cam-clay models prove to be successful in modelling normally consolidated clays, it is well known that they cannot predict many important features of the behavior of sands and overconsolidated clays. By adopting a general stress ratio-state parameter relation to describe the state boundary surface of soils, it is shown that a simple, unified constitutive model (CASM) can be developed for both clay and sand. It is also demonstrated that the standard Cam-clay yield surfaces can be either recovered or approximated as special cases of the yield locus assumed in CASM. The main feature of the proposed model is that a single set of yield and plastic potential functions has been used to model the behaviour of clay and sand under both drained and undrained loading conditions. In addition, it is shown that the behaviour of overconsolidated clays can also be satisfactorily modelled. Simplicity is a major advantage of the present state parameter model, as only two new material constants need to be introduced when compared with the standard Cam-clay models. © 1998 John Wiley & Sons, Ltd.     

一种适用于饱和黏土循环动力分析边界面塑性模型的隐式积分算法

修正了传统隐式回映算法,建立了适用于饱和黏土循环动力分析的边界面塑性模型的完全隐式积分格式。该模型基于无弹性域概念和临界状态理论,采用各向同性、运动硬化准则、旋转的边界面,并引入表征土体结构损伤和重塑程度的损伤变量以反映循环载荷作用下饱和黏土的各向异性、刚度、强度软化及塑性变形累积等特征。针对等压固结 和偏压固结 的饱和高岭黏土的不排水三轴试验进行模拟,采用不同的应变增量步长进行计算,并与试验数据对比,结果表明,修正隐式回映算法应用于该类边界面模型的合理性、积分格式的精确性和稳定性;另外,结合有限元软件自动时间步长的增量迭代解法,对饱和黏土应力控制的不排水动三轴试验进行预测,结果表明,修正的适用于该边界面的塑性模型隐式回映算法可以得到比较合理的数值分析结果,能够反映饱和黏土的循环刚度的退化和强度的弱化等动力特性。     

Kinematic hardening of soft clay in simple shear

In a separate paper, the authors have proposed a normalized, non-degrading form of the shear stress–shear strain relationship for undrained, cyclic simple shear of soft clay. This relationship is described in the present paper, and it is seen to include a single fatigue parameter—the mean effective stress. Application of the relationship therefore requires knowledge of the history of the mean effective stress during any loading history. The present paper proposes an effective stress path model which may be used for prediction of this history. The model is developed within the framework of bounding surface kinematic and isotropic hardening plasticity. It incorporates an isotropic hardening bounding surface, and a kinematic hardening yield surface, in which the elastic region vanishes, and so the yield surface reduces to the stress point. The normalized shear stress–shear strain relationship, developed on the basis of Iwan's model, is used to establish the shape of the cap of the bounding surface. A new translation rule is also incorporated in the model, allowing improved prediction of stress path development within the bounding surface during regular or irregular cyclic loading. Use of the proposed model to simulate the behaviour of soft clay in laboratory undrained cyclic simple shear tests shows excellent qualitative agreement, with most of the major features of the actual behaviour being predicted.     

循环荷载下非饱和结构性黏土的弹塑性双面模型

非饱和黏土的结构性能够显著影响其力学特性。基于非饱和土经典模型BBM（Barcelona basic model）和一种可描述循环塑性的硬化法则,引入体积破损率的作为标准土体结构破损的参数,建立了一个描述常吸力下非饱和结构性黏土静态及动态力学特性的弹塑性双面模型。模型在应力空间中包含与重塑非饱和土屈服面几何相似的结构性边界面和加载面,采用径向映射法则和可移动的记忆中心原理,通过结构性边界面和加载面在应力空间中的演化来反映循环加载过程中非饱和结构性黏土的循环塑性特征和结构损伤过程。通过与相关非饱和黏土控制吸力试验数据的比较,表明该模型能够较好地反映静态加载下非饱和结构性黏土的力学特性,而模型预测的循环荷载下的应力?应变特征也具有一定的合理性。     

循环荷载作用下饱和软土的各向异性边界面模型

在临界状态弹塑性力学的框架内,建立了可以考虑循环荷载作用下各向异性对饱和软土力学特性影响的边界面塑性模型。该模型采用非关联的流动法则,引入了反映土体各向异性的内变量,利用该内变量的初始值描述初始各向异性,采用一种理论更为严谨、模型参数确定更为恰当的旋转硬化法则描述循环加载过程中各向异性的演化,利用更新映射中心的径向映射法则和与塑性偏应变路径长度有关的塑性模量插值规律,保证模型能够模拟循环加载时应力-应变响应的非线性、滞回性、应变累积性等基本特性,解释了模型参数的物理意义和确定方法,特别是给出了一种合理确定描述土体初始各向异性状态变量方法。通过文献中等压固结和偏压固结饱和黏土的循环三轴试验结果与模型预测结果的对比验证了模型的合理性。