Conceptual design and full‐scale experimentation of cladding panel connection systems of precast buildings

Despite the long series of European research projects that has led to the setting of fully reliable seismic design criteria for precast structures, recent earthquakes have shown that a weak point still exists in the proportioning of the connection systems of cladding wall panels. Following this finding, this paper outlines an organic setting of the design problem of precast concrete structures including cladding–structure interaction and describes three possible solutions, namely, the isostatic, integrated, and dissipative systems. The related fastening arrangements, with the use of existing and innovative connection devices, are also described. This paper comments on the results of the pseudo‐dynamic and cyclic tests performed at ELSA Laboratory of the European Joint Research Centre of Ispra (Italy) on a full‐scale prototype of precast structure. The conception and the experimental performance of the structure with nine different configurations of either vertical or horizontal wall panel claddings are presented. The analysis of the results highlights the effectiveness of the different solutions in a comparative way. Copyright © 2017 John Wiley & Sons, Ltd.     

Experimental tests on full‐scale RC unretrofitted frame and retrofitted with buckling‐restrained braces

The results of experimental tests carried out on reinforced concrete (RC) full‐scale 2‐storey 2‐bays framed buildings are presented. The unretrofitted frame was designed for gravity loads only and without seismic details; such frame was assumed as a benchmark system in this study. A similar RC frame was retrofitted with buckling‐restrained braces (BRBs). The earthquake structural performance of both prototypes was investigated experimentally using displacement‐controlled pushover static and cyclic lateral loads. Modal response properties of the prototypes were also determined before and after the occurrence of structural damage. The results of the dynamic response analyses were utilized to assess the existing design rules for the estimation of the elastic and inelastic period of vibrations. Similarly, the values of equivalent damping were compared with code‐base relationships. It was found that the existing formulations need major revisions when they are used to predict the structural response of as‐built RC framed buildings. The equivalent damping ratio ξ_eq was augmented by more than 50% when the BRBs was employed as bracing system. For the retrofitted frame, the overstrength Ω and the ductility µ are 1.6 and 4.1, respectively; the estimated R‐factor is 6.5. The use of BRBs is thus a viable means to enhance efficiently the lateral stiffness and strength, the energy absorption and dissipation capacity of the existing RC substandard frame buildings. The foundation systems and the existing members of the superstructure are generally not overstressed as the seismic demand imposed on them can be controlled by the axial stiffness and the yielding force of the BRBs. Copyright © 2011 John Wiley & Sons, Ltd.     

Interaction between cladding and structural frame observed in a full‐scale steel building test

Interaction between the external wall cladding and the seismic load resisting frame was examined in a full‐scale cyclic loading test of a three‐storey steel building structure. The building specimen had Autoclaved Lightweight Concrete (ALC, also designated as Autoclaved Aerated Concrete) panels installed and anchored to the structural frame as external wall cladding, using a standard Japanese method developed following the 1995 Kobe earthquake. ALC panelling is among the most widely used material for claddings in Japan. In the test, the ALC panel cladding contributed little to the stiffness and strength of the overall structure, even under a very large storey drift of 0.04 rad. No visible damage was noted in the ALC panels other than minor cracks and spalling of the bottom of the panels in the first storey. Consequently, in a Japanese steel building with properly installed ALC panel cladding, the structural frame is likely to be little affected by its cladding, and the ALC panels are capable of accommodating the maximum storey drift generally considered in structural design without sustaining discernible damage. Copyright © 2006 John Wiley & Sons, Ltd.     

Yield frequency spectra and seismic design of code‐compatible RC structures: an illustrative example

The seismic design of an eight‐story reinforced concrete space frame building is undertaken using a yield frequency spectra (YFS) performance‐based approach. YFS offer a visual representation of the entire range of a system's performance in terms of the mean annual frequency (MAF) of exceeding arbitrary global ductility or displacement levels versus the base shear strength. As such, the YFS framework can establish the required base shear and corresponding first‐mode period to satisfy arbitrary performance objectives for any structure that may be approximated by a single‐degree‐of‐freedom system with given yield displacement and capacity curve shape. For the eight‐story case study building, deformation checking is the governing limit state. A conventional code‐based design was performed using seismic intensities tied to the desired MAF for safety checking. Then, the YFS‐based approach was employed to redesign the resulting structure working backwards from the desired MAF of response (rather than intensity) to estimate an appropriate value of seismic intensity for use within a typical engineering design process. For this high‐seismicity and high‐importance midrise building, a stiffer system with higher base shear strength was thus derived. Moreover, performance assessment via incremental dynamic analysis showed that while the code‐design did not meet the required performance objective, the YFS‐based redesign needed only pushover analysis results to offer a near‐optimal design outcome. The rapid convergence of the method in a single design/analysis iteration emphasized its efficiency and practicability as a design aid for practical application. Copyright © 2017 John Wiley & Sons, Ltd.     

基于抗震承载力和改进能力谱法的钢筋混凝土结构耐久性设计

钢筋混凝土结构是一种广泛使用的结构形式,其耐久性设计是一个十分迫切需要解决的问题。在一般大气环境下,混凝土碳化和钢筋锈蚀是钢筋混凝土结构耐久性的重要影响因素,在其作用下结构的抗震承载力发生变化,因此可将结构抗震承载力因素引入结构的耐久性设计中。采用改进能力谱法,以罕遇地震下薄弱层的弹塑性层间位移作为结构承载力指标,研究了一般大气环境下钢筋锈蚀因素对钢筋混凝土结构抗震耐久性的影响,提出了基于抗震承载力和改进的能力谱法的钢筋混凝土结构耐久性设计方法。通过一个五层钢筋混凝土结构的算例说明了验算结构抗震性能耐久行的必要性。     

钢筋混凝土框架柱的变形能力及基于性能的抗震设计方法

框架柱的变形能力主要取决于轴压比和约束箍筋用量,本文建立了柱塑性铰区配箍特征值λcv,轴压比n及塑性铰极限转动量θplc^u之间的函数关系,即λcv-n-θplc^u关系式,并与柱试验数据进行了对比,计算公式与试验结果在平均意义上吻合很好。文中推导了柱截面λcv-n-μcφ关系式,建立了配箍特征值λcv、轴压比n、柱曲率延性μcφ之间的关系。在本文公式的基础上,讨论了按现行抗震设计规范最小配箍要求的RC框架柱所达到的最大变形能力,同时指出规范的构造要求并不总满足特定的变形要求。文中提出了框架柱的性能设计方程,给出了框架柱在指定性能目标DI下基于性能的抗震设计方法的基本过程。     

钢筋混凝土框架梁的变形能力及基于性能的抗震设计方法

本文以Priestley改进的Mander约束混凝土模型为基础推导了RC梁截面λbv-ξn-μbψ关系的一般计算公式和简化计算公式λbv-ξ-μbψ,建立了配箍特征值λbv、相对受压区高度ξn及曲率延性μbψ三者之间的量化关系式,用于梁截面在目标曲率延性下的变形能力设计,给出了梁截面在目标曲率延性下的设计流程图.对所设计的梁截面进行变形能力验算,均可达到设定的目标曲率延性.在简化的λbv-ξ-μbψ公式基础上建立了框架梁的性能设计方程,即λbv-ξ-θplb关系式,给出了RC框架梁基于性能的抗震设计方法的一般步骤.设计者可灵活地根据性能要求设定可接受的破损指标DI进行梁的性能设计.     

Multiobjective optimization for performance‐based seismic design of steel moment frame structures

The performance‐based seismic design of steel special moment‐resisting frame (SMRF) structures is formulated as a multiobjective optimization problem, in which conflicting design criteria that respectively reflect the present capital investment and the future seismic risk are treated simultaneously as separate objectives other than stringent constraints. Specifically, the initial construction expenses are accounted for by the steel material weight as well as by the number of different standard steel section types, the latter roughly quantifying the degree of design complexity related additional construction cost; the seismic risk is considered in terms of maximum interstory drift demands at two hazard levels with exceedance probabilities being 50% and 2% in 50 years, respectively. The present formulation allows structural engineers to find an optimized design solution by explicitly striving for a desirable compromise between the initial investment and seismic performance. Member sizing for code‐compliant design of a planar five‐story four‐bay SMRF is presented as an application example using the proposed procedure that is automated by a multiobjective genetic algorithm. Copyright © 2004 John Wiley & Sons, Ltd.     

Establishment of performance‐based seismic design factors for precast concrete floor diaphragms

This paper presents an analytical study used to establish design factors for a new seismic design methodology for precast concrete floor diaphragms. The design factors include diaphragm force amplification factors Ψ and diaphragm shear overstrength factors Ω_v. The Ψ factors are applied to the ASCE7‐05 diaphragm design forces to produce diaphragm design strengths aligned to different performance targets. These performance targets are based on diaphragm detailing choices, and include: (i) elastic diaphragm behavior or (ii) limiting inelastic deformation demand on the diaphragm reinforcement (connectors between precast units or reinforcing bars in a topping slab) to within their reliable deformation capacities. The Ω_v factors provide overstrength relative to the diaphragm bending strength for capacity protection against shear failure. The analytical study was performed by conducting nonlinear time history analyses of a simple evaluation structure, of which the dimensions and structural properties were varied. The analytical model used in the study is constructed and calibrated on the basis of extensive physical testing. The analytically obtained values of the diaphragm design factors are presented as functions of the geometric and structural properties of the building. The design factors presented here have been verified through evaluation of a set of realistic precast prototype structures. The diaphragm design methodology is currently in the codification process. Copyright © 2015 John Wiley & Sons, Ltd.     

Merging energy‐based design criteria and reliability‐based methods: exploring a new concept

This paper examines the potential development of a probabilistic design methodology, considering hysteretic energy demand, within the framework of performance‐based seismic design of buildings. This article does not propose specific energy‐based criteria for design guidelines, but explores how such criteria can be treated from a probabilistic design perspective. Uniform hazard spectra for normalized hysteretic energy are constructed to characterize seismic demand at a specific site. These spectra, in combination with an equivalent systems methodology, are used to estimate hysteretic energy demand on real building structures. A design checking equation for a (hypothetical) probabilistic energy‐based performance criterion is developed by accounting for the randomness of the earthquake phenomenon, the uncertainties associated with the equivalent system analysis technique, and with the site soil factor. The developed design checking equation itself is deterministic, and requires no probabilistic analysis for use. The application of the proposed equation is demonstrated by applying it to a trial design of a three‐storey steel moment frame. The design checking equation represents a first step toward the development of a performance‐based seismic design procedure based on energy criterion, and additional works needed to fully implement this are discussed in brief at the end of the paper. Copyright © 2006 John Wiley & Sons, Ltd.     

Use of the conditional spectrum to incorporate record‐to‐record variability in simplified seismic assessment of RC wall buildings

A procedure for incorporating record‐to‐record variability into the simplified seismic assessment of RC wall buildings is presented. The procedure relies on the use of the conditional spectrum to randomly sample spectral ordinates at relevant periods of vibration. For inelastic response, displacement reduction factors are then used to relate inelastic displacement demand to the spectral displacement at the effective period for single‐degree‐of‐freedom systems. Simple equations are used to convert back and forth between multi‐degree‐of‐freedom RC wall buildings and equivalent single‐degree‐of‐systems so that relevant engineering demand parameters can be obtained. Consideration is also given to higher‐mode effects by adapting existing modal combination rules. The proposed method is applied to several case study buildings, showing promising results in the examination of inter‐storey drift ratio and shear forces. The proposed method captures the variation in the distribution of structural response parameters that occurs with variations in structural configuration, intensity, engineering demand parameter of interest and site characteristics. Discussion is provided on possible ways to improve the accuracy of the procedure and suggestions for additional future work. Copyright © 2015 John Wiley & Sons, Ltd.     

Energy demands for seismic design against low‐cycle fatigue

A seismic design procedure that does not take into account the maximum and cumulative plastic deformation demands that a structure is likely to undergo during severe ground motion could lead to unsatisfactory performance. In spite of this, current design procedures do not take into account explicitly the effect of low‐cycle fatigue. Based on the high correlation that exists between the strength reduction factor and the energy demand in earthquake‐resistant structures, simple procedures can be formulated to estimate the cumulative plastic deformation demands for design purposes. Several issues should be addressed during the use of plastic energy within a practical performance‐based seismic design methodology. Copyright © 2006 John Wiley & Sons, Ltd.     

Uniform fragility spectra for the performance‐based seismic design of structures considering variabilities in structural properties

This paper presents a new methodology based on structural performance to determine uniform fragility design spectra, i.e., spectra with the same probability of exceedance of a performance level for a given seismic intensity. The design spectra calculated with this methodology provide directly the lateral strength, in terms of yield‐ pseudo‐accelerations, associated with the rate of exceedance of a specific ductility characterizing the performance level for which the structures will be designed. This procedure involves the assessment of the seismic hazard using a large enough number of seismic records of several magnitudes; these records are simulated with an improved empirical Green function method. The statistics of the performance of a single degree of freedom system are obtained using Monte Carlo simulation considering the seismic demand, the fundamental period, and the strength of the structure as uncertain variables. With these results, the conditional probability that a structure exceeds a specific performance level is obtained. The authors consider that the proposed procedure is a significant improvement to others considered in the literature and a useful research tool for the further development of uniform fragility spectra that can be used for the performance‐based seismic design and retrofit of structures.     

Direct design method based on seismic capacity redundancy for structures with metal yielding dampers

In this study, a direct static design method for structures with metal yielding dampers is proposed based on a new design target called the seismic capacity redundancy indicator (SCRI). The proposed method is applicable to the design of elastic‐plastic damped structures by considering the influence of damper on different structural performance indicators separately without the need for iteration or nonlinear dynamic analysis. The SCRI—a quantitative measure of the seismic capacity redundancy—is defined as the ratio of the seismic demand required by the target performance limit to the design seismic demand. Changes in the structural SCRI are correlated with the parameters of the supplemental dampers so that the dampers can be directly designed according to a given target SCRI. The proposed method is illustrated through application to a 12‐story reinforced‐concrete frame, and increment dynamic analysis is performed to verify the effectiveness of the proposed method. The seismic intensity corresponding to the target structural performance limit is regarded as a measure of the structural seismic capacity. The required seismic intensity increases after the structure is equipped with the designed metal yielding dampers according to the expected SCRI. It is concluded that the proposed method is easy to implement and feasible for performance‐based design of metal yielding dampers.     

RC剪力墙结构小震与中震设计对比及其抗震性能研究

近年来,国内学者强调对于复杂和超限结构需进行中震性能设计,即在小震弹性设计后进行中震下的承载力复核及调整,然而中震设计能否提高结构整体抗震性能仍存在争议.为探究中震设计与小震设计方法的差异,本文依据现行规范,以设防烈度、结构高度和场地类别为变化参数,建立了48个典型RC剪力墙模型,并分别以"小震"、"高规中震"、"广东...     

SOFIE project – 3D shaking table test on a seven‐storey full‐scale cross‐laminated timber building

Multi‐storey buildings made of cross‐laminated timber panels (X‐lam) are becoming a stronger and economically valid alternative in Europe compared with traditional masonry or concrete buildings. During the design process of these multi‐storey buildings, also their earthquake behaviour has to be addressed, especially in seismic‐prone areas such as Italy. However, limited knowledge on the seismic performance is available for this innovative massive timber product. On the basis of extensive testing series comprising monotonic and reversed cyclic tests on X‐lam panels, a pseudodynamic test on a one‐storey X‐lam specimen and 1D shaking table tests on a full‐scale three‐storey specimen, a full‐scale seven‐storey building was designed according to the European seismic standard Eurocode 8 and subjected to earthquake loading on a 3D shaking table. The building was designed with a preliminary action reduction factor of three that had been derived from the experimental results on the three‐storey building. The outcomes of this comprehensive research project called ‘SOFIE – Sistema Costruttivo Fiemme’ proved the suitability of multi‐storey X‐lam structures for earthquake‐prone regions. The buildings demonstrated self‐centring capabilities and high stiffness combined with sufficient ductility to avoid brittle failures. The tests provided useful information for the seismic design with force‐based methods as defined in Eurocode 8, that is, a preliminary experimentally based action reduction factor of three was confirmed. Valid, ductile joint assemblies were developed, and their importance for the energy dissipation in buildings with rigid X‐lam panels became evident. The seven‐storey building showed relatively high accelerations in the upper storeys, which could lead to secondary damage and which have to be addressed in future research. Copyright © 2013 John Wiley & Sons, Ltd.     

Single precast concrete rocking walls as earthquake force‐resisting elements

Precast concrete walls with unbonded post‐tensioning provide a simple self‐centering system. Yet, its application in seismic regions is not permitted as it is assumed to have no energy dissipation through a hysteretic mechanism. These walls, however, dissipate energy imparted to them because of the wall impacting the foundation during rocking and limited hysteretic action resulting from concrete nonlinearity. The energy dissipated due to rocking was ignored in previous experimental studies because they were conducted primarily using quasi‐static loading. Relying only on limited energy dissipation, a shake table study was conducted on four single rocking walls (SRWs) using multiple‐level earthquake input motions. All walls generally performed satisfactorily up to the design‐level earthquakes when their performance was assessed in terms of the maximum transient drift, maximum absolute acceleration, and residual drift. However, for the maximum considered earthquakes, the walls experienced peak lateral drifts greater than the permissible limits. Combining the experimental results with an analytical investigation, it is shown that SRWs can be designed as earthquake force‐resisting elements to produce satisfactory performance under design‐level and higher‐intensity earthquake motions. Copyright © 2016 John Wiley & Sons, Ltd.     

Probabilistic evaluation of seismic performance of 3‐story 3D one‐ and two‐way steel moment‐frame structures

This paper presents the results of a probabilistic evaluation of the seismic performance of 3D steel moment‐frame structures. Two types of framing system are considered: one‐way frames typical of construction in the United States and two‐way frames typical of construction in Japan. For each framing system, four types of beam–column connections are considered: pre‐Northridge welded‐flange bolted‐web, post‐Northridge welded‐flange welded‐web, reduced‐beam‐section, and bolted‐flange‐plate connections. A suite of earthquake ground motions is used to compute the annual probability of exceedence (APE) for a series of drift demand levels and for member plastic‐rotation capacity. Results are compared for the different framing systems and connection details. It is found that the two‐way frames, which have a larger initial stiffness and strength than the one‐way frames for the same beam and column volumes, have a smaller APE for small drift demands for which members exhibit no or minimal yielding, but have a larger APE for large drift demands for which members exhibit large plastic rotations. However, the one‐way frames, which typically comprise a few seismic frames with large‐sized members that have relatively small rotation capacities, may have a larger APE for member failure. The probabilistic approach presented in this study may be used to determine the most appropriate frame configuration to meet an owner's performance objectives. Copyright © 2008 John Wiley & Sons, Ltd.     

Hybrid experimental performance of a full‐scale two‐story buckling‐restrained braced RC frame

This paper proposes a novel implementation of buckling‐restrained braces (BRB) in new reinforced concrete (RC) frame construction. Seismic design and analysis methods for using a proposed steel cast‐in anchor bracket (CAB) to transfer normal and shear forces between the BRB and RC members are investigated. A full‐scale two‐story RC frame with BRBs (BRB‐RCF) is tested using hybrid and cyclic loading test procedures. The BRBs were arranged in a zigzag configuration and designed to resist 70% of the story shear. The gusset design incorporates the BRB axial and RCF actions, while the beam and column members comply with ACI 318‐14 seismic design provisions. Test results confirm that the BRBs enhanced the RCF stiffness, strength, and ductility. The hysteresis energy dissipation ratios in the four hybrid tests range from 60% to 94% in the two stories, indicating that BRBs can effectively dissipate seismic input energy. When the inter‐story drift ratio for both stories reached 3.5% in the cyclic loading test, the overall lateral force versus deformation response was still very stable. No failure of the proposed steel CABs and RC discontinuity regions was observed. This study demonstrates that the proposed design and construction methods for the CABs are effective and practical for real applications. Copyright © 2016 John Wiley & Sons, Ltd.     

Earthquake‐resistant structural design through energy demand and capacity

An energy‐based earthquake‐resistant structural design method is proposed. The proposed method uses specific input energy spectra, modal or time‐history analyses, and energy distribution among structural members. For a given member strength and stiffness, a relationship between the energy attributable to damage absorbed by a member and its cumulative ductility demand can be determined. Member strength, stiffness and energy capacity are design parameters which are simultaneously used in the design. The method can avoid soft‐storey design. The damage is measured based on a cumulative basis considering earthquake magnitude, frequency, and duration. Tests have been carried out to determine energy absorbing capacities of various structural components. More efforts are needed to make the energy‐based earthquake‐resistant structural design practical, but ssimple formulations for this method are possible. Copyright © 2007 John Wiley & Sons, Ltd.