Seismic isolation of cable‐stayed bridges for near‐field ground motions

This study examines the efficacy of using seismic isolation to favorably influence the seismic response of cable‐stayed bridges subjected to near‐field earthquake ground motions. In near‐field earthquake ground motions, large amplitude spectral accelerations can occur at long periods where many cable‐stayed bridges have significant structural response modes. This combination of factors can result in large tower accelerations and base shears. In this study, lead–rubber bearing seismic isolators were modeled for three cable‐stayed bridges, and three cases of isolation were examined for each bridge. The nine isolated bridge configurations, plus three non‐isolated configurations as references, were subjected to near‐field earthquake ground motions using three‐dimensional time‐history analyses. Introduction of a small amount of isolation is shown to be very beneficial in reducing seismic accelerations and forces while at the same time producing only a modest increase in the structural displacements. There is a low marginal benefit to continue to increase the amount of isolation by further lengthening the period of the structure because structural forces and accelerations reduce at a diminishing rate whereas structural displacements increase substantially. In virtually all cases the base shears in the isolated bridges were reduced by at least 50several instances by up to 80individual near‐field records showed large variability from one record to the next, with coefficients of variation about the mean as large as 50assessing the characteristics of near‐field ground motion for use in isolation design of cable‐stayed bridges. Copyright © 2003 John Wiley & Sons, Ltd.     

Evaluation of the measured seismic response of the Mexico City Cathedral

The seismic response of the Mexico City Cathedral built of very soft soil deposits is evaluated by using motions recorded in various parts of the structure during several moderate earthquakes. This unique set of records provides significant insight into the seismic response of this and other similar historic stone masonry structures. Free‐field ground motions are carefully compared in time and frequency domains with motions recorded at building basement. The dynamic characteristics of the structure are inferred from the earthquake records by using system identification techniques. Variation of seismic response for different seismic intensities is discussed. It is shown that, due to the soil–structure interaction, due to large differences between dominant frequencies of earthquake ground motions at the site and modal frequencies of vibration of the structure, and due to a particularly high viscous damping, seismic amplifications of ground motion in this and similar historic buildings erected on soft soil deposits are much smaller than that induced in most modern constructions. Nevertheless, earthquake records and analytical results show that several components of the structure such as its central dome and the bell towers may be subjected to local vibrations that significantly amplify ground motions. Overall, results indicate that in its present state the structure has an acceptable level of seismic safety. Copyright © 2008 John Wiley & Sons, Ltd.     

Ground motion characteristics of the Chi‐Chi earthquake of 21 September 1999

The purpose of this paper is to investigate the ground motion characteristics of the Chi‐Chi earthquake (21 September 1999) as well as the interpretation of structural damage due to this earthquake. Over 300 strong motion records were collected from the strong motion network of Taiwan for this earthquake. A lot of near‐field ground motion data were collected. They provide valuable information on the study of ground motion characteristics of pulse‐like near‐field ground motions as well as fault displacement. This study includes: attenuation of ground motion both in PGA and spectral amplitude, principal direction, elastic and inelastic response analysis of a SDOF system subjected to near‐field ground motion collected from this event. The distribution of spectral acceleration and spectral velocity along the Chelungpu fault is discussed. Based on the mode decomposition method the intrinsic mode function of ground acceleration of this earthquake is examined. A long‐period wave with large amplitude was observed in most of the near‐source ground acceleration. The seismic demand from the recorded near‐field ground motion is also investigated with an evaluation of seismic design criteria of Taiwan Building Code. Copyright © 2000 John Wiley & Sons, Ltd.     

Regional seismic responses of shallow basins incorporating site‐city interaction analyses on high‐rise building clusters

This study assesses the 3D amplification effects in shallow basins and quantifies the effects of site‐city interaction (SCI) on high‐rise buildings. A regional‐scale 3D spectral element simulation is conducted on the Tuen Mun‐Yuen Long basin, which contains multiple subbasins with heterogeneous and nonlinear soil profiles, while 3D city models with various building layouts are fully integrated into the basin model for our SCI study. We found a good correlation between spectral amplification factors and soil depths. Site response is significantly amplified at basin edges and centers due to surface waves generated at basin edges and the focusing effects stemming from 3D basin geometry. Transfer functions of 3D basins can be up to fourfold at fundamental frequencies as compared to 1D response, and further amplifications occur at high frequencies due to surface waves. In the SCI simulations, we observe wave trapping in the open space amid buildings resulting in energy concentration and up to twofold PGA amplifications. The wave trapping effect diminishes as the space between buildings increase beyond their range of influence (～100 m). The SCI analyses show that destructive kinetic energy in superstructures increases 28% in one horizontal direction but decreases 22% in the other. Our study concluded that, 1D site response analysis can significantly underestimate the seismic demand in shallow basins. Site‐city interaction of high‐rise buildings increases the short‐period spectra of ground motions, leading to an increase in their story accelerations by up to 50% and to a substantial decrease in the seismic safety of short structures in their vicinity.     

饱和土体-地下综合管廊结构地震响应分析

将土体视为固-液两相介质,基于饱和土体有效应力原理,建立饱和土体-地下综合管廊结构体系相互作用动力模型:在地应力平衡的静力状态下采用Duncan-Chang非线性弹性本构模型,在地震波作用的动力状态下采用Davidenkov非线性黏弹性本构模型;考虑饱和土体黏弹性动力人工边界条件,将地震动作用转化为作用在人工边界节点上的动力荷载。模型考察不同地震波时程、地震波加速度峰值、入射角度、孔隙率以及地应力场的影响,得出如下结论:(1)地震波的卓越周期与场地卓越周期相近时引起结构上的变形最大;随着地震波加速度峰值的增大结构变形增大;随着地震波入射角度的增加结构变形增大,地震波斜入射情况下产生的行波效应使得结构变形最大。(2)土体材料的孔隙水压力是影响地震中结构变形的主要因素之一。(3)将土体材料考虑为单相介质时结构上的变形要比考虑为固-液两相介质时大得多,直接将饱和土体场地中得到的地震波等效荷载施加到单相土介质-结构动力相互作用模型上,能够得到与完全基于有效应力法一致的结果。     

SOFIE project – 3D shaking table test on a seven‐storey full‐scale cross‐laminated timber building

Multi‐storey buildings made of cross‐laminated timber panels (X‐lam) are becoming a stronger and economically valid alternative in Europe compared with traditional masonry or concrete buildings. During the design process of these multi‐storey buildings, also their earthquake behaviour has to be addressed, especially in seismic‐prone areas such as Italy. However, limited knowledge on the seismic performance is available for this innovative massive timber product. On the basis of extensive testing series comprising monotonic and reversed cyclic tests on X‐lam panels, a pseudodynamic test on a one‐storey X‐lam specimen and 1D shaking table tests on a full‐scale three‐storey specimen, a full‐scale seven‐storey building was designed according to the European seismic standard Eurocode 8 and subjected to earthquake loading on a 3D shaking table. The building was designed with a preliminary action reduction factor of three that had been derived from the experimental results on the three‐storey building. The outcomes of this comprehensive research project called ‘SOFIE – Sistema Costruttivo Fiemme’ proved the suitability of multi‐storey X‐lam structures for earthquake‐prone regions. The buildings demonstrated self‐centring capabilities and high stiffness combined with sufficient ductility to avoid brittle failures. The tests provided useful information for the seismic design with force‐based methods as defined in Eurocode 8, that is, a preliminary experimentally based action reduction factor of three was confirmed. Valid, ductile joint assemblies were developed, and their importance for the energy dissipation in buildings with rigid X‐lam panels became evident. The seven‐storey building showed relatively high accelerations in the upper storeys, which could lead to secondary damage and which have to be addressed in future research. Copyright © 2013 John Wiley & Sons, Ltd.     

Ground‐shaking mapping for a scenario earthquake considering effects of geological conditions: a case study for the 1995 Hyogo‐ken Nanbu,Japan earthquake

In order to examine the applicability of ground‐shaking mapping techniques to a near‐field earthquake, a peak ground velocity map of the 1995 Hyogo‐ken Nanbu, Japan earthquake computed from seismic zoning methods that consider the effects of geological conditions is compared with the actual observed intensity map. When computing the ground‐shaking map, the site amplification at each site is calculated in terms of the average shear‐wave velocity of the ground estimated from the corresponding geomorphological conditions. This map shows a relatively good agreement with the observed intensity map. However, the computations provide smaller values for certain disastrous areas of the earthquake, where the effects on ground motion of a deep, irregular underground structure have been reported. The effect of such structures on site response is examined implementing 2D FEM analyses, thereby being also incorporated into the method. Results considering the effect of the irregular underground structure show better agreement with the observed intensity map. Copyright © 2002 John Wiley & Sons, Ltd.     

Development and validation of p‐y modeling approach for seismic response predictions of highway bridges

This study aims to realistically simulate the seismic responses of typical highway bridges in California with considerations of soil–structure interaction effects. The p‐y modeling approaches are developed and validated for embankments and pile foundations of bridges. The p‐y approach models the lateral and vertical foundation flexibility with distributed p‐y springs and associated t‐z and q‐z springs. Building upon the existing p‐y models for pile foundations, the study develops the nonlinear p‐y springs for embankments based on nonlinear 2D and 3D continuum finite element analysis under passive loading condition along both longitudinal and transverse directions. Closed‐form expressions are developed for two key parameters, the ultimate resistant force p_ult and the displacement y₅₀, where 0.5p_ult is reached, of embankment p‐y models as functions of abutment geometry (wall width and height, embankment fill height, etc.) and soil material properties (wall‐soil friction angle, soil friction angle, and cohesion). In order to account for the kinematic and site responses, depth‐varying ground motions are derived and applied at the free‐end of p‐y springs, which reflects the amplified embankment crest motion. The modeling approach is applied to simulate the seismic responses of the Painter Street Bridge and validated through comparisons with the recorded responses during the 1992 Petrolia earthquake. It is demonstrated that the flexibility and motion amplification at end abutments are the most crucial modeling aspects. The developed p‐y models and the modeling approach can effectively predict the seismic responses of highway bridges. Copyright © 2016 John Wiley & Sons, Ltd.     

Comprehensive numerical analysis of fault‐structure systems – Computation of the large‐scale seismic structural response to a given earthquake scenario –

The seismic structural response is affected by temporal and spatial variations in strong ground motion. It can be evaluated through the fault‐structure system: the fault mechanism, wave propagation through the crust, amplification near the surface, and soil‐structure interaction. To analyze this system at high resolution and accuracy, we previously proposed a new multiscale analysis method and numerically verified its validity. However, the problem of the extremely large computation cost of constructing a three‐dimensional numerical model and solving the discretized governing equations still remains. Here, we introduce a new method to resolve these difficulties. By combining this new method with our multiscale analysis, we developed a tool for fault‐structure system analysis. The accuracy of this tool is verified by comparing it to a Green's function solution. Finally, we demonstrate the potential utility of the method by estimating the seismic response of a large and complex underground highway junction in a given earthquake scenario. Copyright © 2011 John Wiley & Sons, Ltd.     

Solving the complex near‐surface problem using 3D data‐driven near‐surface layer replacement

In many land seismic situations, the complex seismic wave propagation effects in the near‐surface area, due to its unconsolidated character, deteriorate the image quality. Although several methods have been proposed to address this problem, the negative impact of 3D complex near‐surface structures is still unsolved to a large extent. This paper presents a complete 3D data‐driven solution for the near‐surface problem based on 3D one‐way traveltime operators, which extends our previous attempts that were limited to a 2D situation. Our solution is composed of four steps: 1) seismic wave propagation from the surface to a suitable datum reflector is described by parametrized one‐way propagation operators, with all the parameters estimated by a new genetic algorithm, the self‐adjustable input genetic algorithm, in an automatic and purely data‐driven way; 2) surface‐consistent residual static corrections are estimated to accommodate the fast variations in the near‐surface area; 3) a replacement velocity model based on the traveltime operators in the good data area (without the near‐surface problem) is estimated; 4) data interpolation and surface layer replacement based on the estimated traveltime operators and the replacement velocity model are carried out in an interweaved manner in order to both remove the near‐surface imprints in the original data and keep the valuable geological information above the datum. Our method is demonstrated on a subset of a 3D field data set from the Middle East yielding encouraging results.     

Input and system identification of the Hualien soil–structure interaction system using earthquake response data

This paper presents an input and system identification technique for a soil–structure interaction system using earthquake response data. Identification is carried out on the Hualien large‐scale seismic test structure, which was built in Taiwan for international joint research. The identified quantities are the input ground acceleration as well as the shear wave velocities of the near‐field soil regions and Young's moduli of the shell sections of the structure. The earthquake response analysis on the soil–structure interaction system is carried out using the finite element method incorporating the infinite element formulation for the unbounded layered soil medium and the substructured wave input technique. The criterion function for the parameter estimation is constructed using the frequency response amplitude ratios of the earthquake responses measured at several points of the structure, so that the information on the input motion may be excluded. The constrained steepest descent method is employed to obtain the revised parameters. The simulated earthquake responses using the identified parameters and input ground motion show excellent agreement with the measured responses. Copyright © 2003 John Wiley & Sons, Ltd.     

Earthquake ground motion modeling of induced seismicity in the Groningen gas field

A physics‐based numerical approach is used to characterize earthquake ground motion due to induced seismicity in the Groningen gas field and to improve empirical ground motion models for seismic hazard and risk assessment. To this end, a large‐scale (20 km × 20 km) heterogeneous 3D seismic wave propagation model for the Groningen area is constructed, based on the significant bulk of available geological, geophysical, geotechnical, and seismological data. Results of physics‐based numerical simulations are validated against the ground motion recordings of the January 8, 2018, M_L 3.4 Zeerijp earthquake. Taking advantage of suitable models of slip time functions at the seismic source and of the detailed geophysical model, the numerical simulations are found to reproduce accurately the observed features of ground motions at epicentral distances less than 10 km, in a broad frequency range, up to about 8 Hz. A sensitivity analysis is also addressed to discuss the impact of 3D underground geological features, the stochastic variability of seismic velocities and the frequency dependence of the quality factor. Amongst others, results point out some key features related to 3D seismic wave propagation, such as the magnitude and distance dependence of site amplification functions, that may be relevant to the improvement of the empirical models for earthquake ground motion prediction.     

The use of 3D modeling for the prediction of the seismic demands on the gravity dams

Seismic behavior of gravity dams has long been evaluated using a representative two‐dimensional (2D) system. Formulated for the gravity dams built in wide canyons, the assumption is nevertheless utilized extensively for almost all concrete dams due to the established procedures as well as the expected computational costs of a three‐dimensional model. However, a significant number of roller‐compacted concrete dams, characterized as such systems, do not conform to the basic assumptions of these methods by violating the conditions on canyon dimensions and joint‐spacing/details. Based on the premise that the 2D modeling assumption is overstretched for practical purposes in a variety of settings, the purpose of this study is to critically evaluate the use of 2D modeling for the prediction of the seismic demands on these systems. Using a rigorous soil–structure interaction approach, the difference between the two and three‐dimensional response for gravity dams was investigated first in the frequency domain for a range of canyon widths and foundation to dam moduli ratios. Then, the time domain differences between the crest displacements and the maximum principal stress were obtained using 70 different ground motions in order to show the possible bias introduced into the analysis results due to the modeling approach. The results of the study show that even for relatively wide canyons, the 2D analysis can lead to misleading predictions. Copyright © 2017 John Wiley & Sons, Ltd.     

Optimum lateral load pattern for seismic design of elastic shear‐buildings incorporating soil–structure interaction effects

Recently, several new optimum loading patterns have been proposed by researchers for fixed‐base systems while their adequacy for soil–structure systems has not been evaluated yet. Through intensive dynamic analyses of multistory shear‐building models with soil–structure interaction subjected to a group of 21 artificial earthquakes adjusted to soft soil design spectrum, the adequacy of these optimum patterns is investigated. It is concluded that using these patterns the structures generally achieve near optimum performance in some range of periods. However, their efficiency reduces as soil flexibility increases especially when soil–structure interaction effects are significant. In the present paper, using the uniform distribution of damage over the height of structures, as the criterion, an optimization algorithm for seismic design of elastic soil–structure systems is developed. The effects of fundamental period, number of stories, earthquake excitation, soil flexibility, building aspect ratio, damping ratio and damping model on optimum distribution pattern are investigated. On the basis of 30,240 optimum load patterns derived from numerical simulations and nonlinear statistical regression analyses, a new lateral load pattern for elastic soil–structure systems is proposed. It is a function of the fundamental period of the structure, soil flexibility and structural slenderness ratio. It is shown that the seismic performance of such a structure is superior to those designed by code‐compliant or recently proposed patterns by researchers for fixed‐base structures. Using the proposed load pattern in this study, the designed structures experience up to 40% less structural weight as compared with the code‐compliant or optimum patterns developed based on fixed‐base structures. Copyright © 2012 John Wiley & Sons, Ltd.     

A frequency‐dependent and intensity‐dependent macroelement for reduced order seismic analysis of soil‐structure interacting systems

The computational demand of the soil‐structure interaction analysis for the design and assessment of structures, as well as for the evaluation of their life‐cycle cost and risk exposure, has led the civil engineering community to the development of a variety of methods toward the model order reduction of the coupled soil‐structure dynamic system in earthquake regions. Different approaches have been proposed in the past as computationally efficient alternatives to the conventional finite element model simulation of the complete soil‐structure domain, such as the nonlinear lumped spring, the macroelement method, and the substructure partition method. Yet no approach was capable of capturing simultaneously the frequency‐dependent dynamic properties along with the nonlinear behavior of the condensed segment of the overall soil‐structure system under strong earthquake ground motion, thus generating an imbalance between the modeling refinement achieved for the soil and the structure. To this end, a dual frequency‐dependent and intensity‐dependent expansion of the lumped parameter modeling method is proposed in the current paper, materialized through a multiobjective algorithm, capable of closely approximating the behavior of the nonlinear dynamic system of the condensed segment. This is essentially the extension of an established methodology, also developed by the authors, in the inelastic domain. The efficiency of the proposed methodology is validated for the case of a bridge foundation system, wherein the seismic response is comparatively assessed for both the proposed method and the detailed finite element model. The above expansion is deemed a computationally efficient and reliable method for simultaneously considering the frequency and amplitude dependence of soil‐foundation systems in the framework of nonlinear seismic analysis of soil‐structure interaction systems.     

Validation of (not‐historical) large‐event near‐fault ground‐motion simulations for use in civil engineering applications

Ground‐motion simulations generated from physics‐based wave propagation models are gaining increasing interest in the engineering community for their potential to inform the performance‐based design and assessment of infrastructure residing in active seismic areas. A key prerequisite before the ground‐motion simulations can be used with confidence for application in engineering domains is their comprehensive and rigorous investigation and validation. This article provides a four‐step methodology and acceptance criteria to assess the reliability of simulated ground motions of not historical events, which includes (1) the selection of a population of real records consistent with the simulated scenarios, (2) the comparison of the distribution of Intensity Measures (IMs) from the simulated records, real records, and Ground‐Motion Prediction Equations (GMPEs), (3) the comparison of the distribution of simple proxies for building response, and (4) the comparison of the distribution of Engineering Demand Parameters (EDPs) for a realistic model of a structure. Specific focus is laid on near‐field ground motions (<10km) from large earthquakes (M_w7), for which the database of real records for potential use in engineering applications is severely limited. The methodology is demonstrated through comparison of (2490) near‐field synthetic records with 5 Hz resolution generated from the Pitarka et al (2019) kinematic rupture model with a population of (38) pulse‐like near‐field real records from multiple events and, when applicable, with NGA‐W2 GMPEs. The proposed procedure provides an effective method for informing and advancing the science needed to generate realistic ground‐motion simulations, and for building confidence in their use in engineering domains.     

Response of hybrid isolation system during a shake table experiment of a full‐scale isolated building

A full‐scale 5‐story steel moment frame building was subjected to a series of earthquake excitations using the E‐Defense shake table in August, 2011. For one of the test configurations, the building was seismically isolated by a hybrid system of lead‐rubber bearings and low friction roller bearings known as cross‐linear bearings, and was designed for a very rare 100 000‐year return period earthquake at a Central and Eastern US soil site. The building was subject to 15 trials including sinusoidal input, recorded motions and simulated earthquakes, 2D and 3D input, and a range of intensities including some beyond the design basis level. The experimental program was one of the first system‐level full‐scale validations of seismic isolation and the first known full‐scale experiment of a hybrid isolation system incorporating lead‐rubber and low friction bearings. Stable response of the hybrid isolation system was demonstrated at displacement demands up to 550 mm and shear strain in excess of 200%. Torsional amplifications were within the new factor stipulated by the code provisions. Axial force was observed to transfer from the lead‐rubber bearings to the cross‐linear bearings at large displacements, and the force transfer at large displacements exceeded that predicted by basic calculations. The force transfer occurred primarily because of the flexural rigidity of the base diaphragm and the larger vertical stiffness of the cross‐linear bearings relative to the lead‐rubber bearings.     

Effects of near-fault and far-fault ground motions on nonlinear dynamic response and seismic damage of concrete gravity dams

As the forward directivity and fling effect characteristics of the near-fault ground motions, seismic response of structures in the near field of a rupturing fault can be significantly different from those observed in the far field. The unique characteristics of the near-fault ground motions can cause considerable damage during an earthquake. This paper presents results of a study aimed at evaluating the near-fault and far-fault ground motion effects on nonlinear dynamic response and seismic damage of concrete gravity dams including dam-reservoir-foundation interaction. For this purpose, 10 as-recorded earthquake records which display ground motions with an apparent velocity pulse are selected to represent the near-fault ground motion characteristics. The earthquake ground motions recorded at the same site from other events that the epicenter far away from the site are employed as the far-fault ground motions. The Koyna gravity dam, which is selected as a numerical application, is subjected to a set of as-recorded near-fault and far-fault strong ground motion records. The Concrete Damaged Plasticity (CDP) model including the strain hardening or softening behavior is employed in nonlinear analysis. Nonlinear dynamic response and seismic damage analyses of the selected concrete dam subjected to both near-fault and far-fault ground motions are performed. Both local and global damage indices are established as the response parameters. The results obtained from the analyses of the dam subjected to each fault effect are compared with each other. It is seen from the analysis results that the near-fault ground motions, which have significant influence on the dynamic response of dam–reservoir–foundation systems, have the potential to cause more severe damage to the dam body than far-fault ground motions.     

Response of nonlinear soil‐MDOF structure systems subjected to distinct frequency‐content components of near‐fault ground motions

This paper is devoted to investigate the effects of near‐fault ground motions on the seismic responses of nonlinear MDOF structures considering soil‐structure interaction (SSI). Attempts are made to take into account the effects of different frequency‐content components of near‐fault records including pulse‐type (PT) and high‐frequency (HF) components via adopting an ensemble of 54 near‐fault ground motions. A deep sensitivity analysis is implemented based on the main parameters of the soil‐structure system. The soil is simulated based on the Cone model concept, and the superstructure is idealized as a nonlinear shear building. The results elucidate that SSI has approximately increasing and mitigating effects on structural responses to the PT and HF components, respectively. Also, a threshold period exists above which the HF component governs the structural responses. As the fundamental period of the structure becomes shorter and structural target ductility reduces, the contribution of the HF component to the structural responses increases, elaborately. Soil flexibility makes the threshold period increase, and the effect of the PT component becomes more significant than the HF one. In the case of soil‐structure system, slenderizing the structure also increases this threshold period and causes the PT component to be dominant. Copyright © 2013 John Wiley & Sons, Ltd.     

Earthquake response analysis of the Hualien soil–structure interaction system based on updated soil properties using forced vibration test data

This paper presents results of the earthquake response analysis on a large‐scale seismic test (LSST) structure which was built at Hualien in Taiwan for an international cooperative research project. The analysis is carried out using a computer program which has been developed based on axisymmetric finite element method incorporating dynamic infinite elements for far‐field soil region and a substructured wave input technique. The non‐linear behaviour of the soil medium is taken into account using an iterative equivalent linearization procedure. Two sets of the soil and structural properties, namely the unified and the FVT‐correlated models, are utilized as the initial linear values. The unified model was provided by a group of experts in charge of the geotechnical experiments, and the correlated model was obtained through a system identification procedure using the forced vibration test (FVT) results by the present authors. Three components of ground accelerations are artificially generated through an averaging process of the Fourier amplitude spectra of the ground accelerations measured near the test structure, and they are used as the control input motions for the earthquake analysis. It has been found that the earthquake responses predicted using the generated control motions and with the FVT‐correlated model as the initial linear properties in the equivalent linearization procedure compare very well with the observed responses. Copyright © 2001 John Wiley & Sons, Ltd.