Study on the determination of trace methyl mercury in seawater by gas chromatography

Sample seawater containing trace methyl mercury was acidified and adsorbed on hydrosulfo-cotton, washed with hydrochloric acid, extracted by benzene and dried, and then determined by a gas chromatograph with electron capture detector. This method, which can detect a minimum concentration of 0.1×10⁻¹⁰%, can be used to monitor the 10⁻¹⁰% content of methyl mercury in seawater.     

The apparent copper complexing capacity of seawater and the interaction of copper with humic matter

The anodic stripping voltammetry with physically-coating mercury film electrode was used to investigate the complexing action of trace heavy metals in seawater with organic ligands. The apparent copper complexing capacity of seawater was determined by titrating the organic ligands in natural seawater with standard ionic copper solution. The complexing actions of copper in seawater with humic acid (HA) or fulvic acid (FA) were investigated by titrating copper in seawater with HA or FA solution. The equilibrium time, electrodeposition potential, and effect of pH etc. were investigated respectively. The results show that the interaction of copper in seawater with organic matter is a fast process. At natural pH, HA or FA tend to act with copper in seawater to form nonlabile complexes. During experimental electrode process, these complexes did not significantly dissociate. The experimental results were calculated according to 1∶1 complex formation.     

Effect of Carbonation and Drying-Wetting Cycles on Chloride Diffusion Behavior of Coral Aggregate Seawater Concrete

Based on seawater immersion,drying-wetting cycles,carbonation and drying-wetting cycles for coral aggregate sea-water concrete(CASC)with different strength grades,the effect of carbonation and drying-wetting cycles on chloride diffusion be-havior of CASC is studied.The results show that the free surface chloride concentration(Cs),free chloride diffusion coefficient(Df)and time-dependent index(m)of CASC in the drying-wetting cycles is obviously higher than that in seawater immersion.The Df and m of CASC of carbonation and drying-wetting cycles is higher than that in the drying-wetting cycles.Carbonation increases the Df and m of CASC,which is against CASC to resist chloride corrosion.The corrosion possibility of CASC structures in different ex-posed areas is as follows:splash zone(carbonation and drying-wetting cycles)>tidal zone(drying-wetting cycles)>underwater zone(seawater immersion).Besides,the chloride diffusion rate of C65-CASC is 17.8%-63.4%higher than that of C65-ordinary aggre-gate concrete(OAC)in seawater immersion(underwater zone).Therefore,anti-corrosion measures should be adopted to improve the service life of CASC structure in the oceanic environment.     

Application of transition metal isotope tracers in global change research

High-precision isotope composition determinations using multicollector, magnetic-sector inductively coupled plasma mass spectrometry (MC-ICPMS) have recently revealed that some transition metal isotopes such as those of Mo, Fe, Cu, Zn etc. can be used as biogeochemical tracers in global change research.The Mo isotope system may be useful in paleoredox investigations indicating that δ^97 ^95Mo in seawater may co-vary with changes in the relative proportions of anoxic and oxic sedimentation in the ocean, and that this variation may be recorded in δ^97 ^95Mo of anoxic sediments. The Mo continental flux into the oceans and the global Mo isotope budget can be estimated from δ^97 ^95M0 values. The Fe isotope composition in seawater is an important issue because Fe plays a controlling role in biological productivity in the oceans and its abundance in seawater may have substantial effect on climate changes. Iron isotope fractionations could result from bio- and abio-processes and have about 0.1% variation ( δ^56 ^54Fe), so Fe isotopes considered alone cannot be used to distinguish the products of abiotic and biotic Fe processing in geological records. Cu and Zn isotopes are also used as biogeochemical tracers, but the researches are relatively less. This review mainly focuses on the methods for preparation, purification and determination of new isotope tracer samples, and on isotope applications in marine environmental changes.     

A NEW BIOGENIC SULFIDE CHEMICAL SENSOR FOR MARINE ENVIRONMENTAL MONITORING AND SURVEY

ＩＮＴＲＯＤＵＣＴＩＯＮＢｉｏｇｅｎｉｃｓｕｌｆｉｄｅｐｒｏｄｕｃｅｄｂｙｂａｃｔｅｒｉａｌｓｕｌｆａｔｅｒｅｄｕｃｔｉｏｎｉｓｏｎｅｏｆｔｈｅｍｏｓｔｉｍｐｏｒｔａｎｔｉｎｄｉｃａｔｏｒｓｉｎａｎｏｘｉｃｍａｒｉｎｅｅｎｖｉｒｏｎｍｅｎｔｓ,ｐａｒｔｉｃｕｌａｒｌｙｉｎｃｏｎｆｉｎｉｎｇｂａｙｓ,ｐｏｌｌｕｔｅｄｅｓｔｕａｒｉｅｓａｎｄａｑｕａｃｕｌｔｕｒｅａｒ ｅａｓ.Ｔｈｅｉｎｃｒｅａｓｅｏｆｉｔｓｃｏｎｃｅｎｔｒａｔｉｏｎｕｓｕａｌｌｙｉｎｄｉｃａｔｅｓｗｏｒｓｅｎｅｄｃｏｎｄｉｔｉｏｎｓ.…     

POTENTIOMETRIC TITRATION OF CALCIUM IN SEAWATER

Atpasent,thestandardmethodfordetendningcalciuminseawateriscomPlexometrictitrationusingEGTA[ethyleneglycol-bis(2-adrinoethylether)-N,N,N',N'-tetraaceticacid]andGHAtelyoxal-bis(2-hydroxyanil)].ThisInethodwasfirStdeveopedbyTSunogaietal.(l968),sumrnarindbyKremling,andeditalinMethodsofSeawaterAnalySisbyGrasshoff(l983).AlthoughtheendpointreadingsinthismethodarenotquitCsharp,andrnaybeaffCCtedbyoveanstweather,withtheuseofcalctumISEasindicatingeledrode,SCEasreferenceeledrodeanddigitalvoltme…     

一种新型光纤光栅锈蚀传感器及其对混凝土结构钢筋锈蚀监测实验研究

设计一种新型光纤光栅锈蚀传感器,主要由锈蚀体、不锈钢体和2段串联的光纤布拉格光栅（FBG）组成。缠绕于锈蚀体表面的FBG监测钢筋的锈胀应变,缠绕于不锈钢体表面的FBG用作温度补偿器,消除温度变化对锈胀应变监测的影响。此外,设计电化学加速腐蚀实验,探究该传感器在不同强度等级混凝土中的工作性能。结果表明,该传感器监测质量腐蚀率的灵敏度为0.02%,监测范围大于1%,可实时监测混凝土中钢筋的锈蚀过程及特征,为预警钢筋锈蚀引起的钢筋混凝土结构耐久性损失提供阈值,在结构健康监测领域具有较大的应用价值。     

Chemical and spectroscopic characterization of dissolved humic substances in a mangrove-fringed estuary in the eastern coast of Hainan Island, China

Mangrove-derived dissolved organic matter(DOM) has an important effect on estuarine and coastal area on a large scale.In order to improve the understanding of origin,composition,and fate of DOM in mangrove-fringed estuarine and coastal areas,dissolved humic substances(DHS) were isolated from one mangrove pore-water sample and one near-shore seawater sample downstream the mangrove pore-water site in the eastern coast of Hainan Island,South China.Fulvic acids,humic acids and XAD-4 fractions were obtained from the two water samples by using a two-column array of XAD-8 and XAD-4 resins.Chemical and spectroscopic methods were used to analyze the features of these DHS.Compared to the mangrove pore-water DHS,the near-shore seawater DHS were found rich in 13 C with lower C/N ratios and more aliphatic compounds and carbohydrates,but less aromatic structures and carboxyl groups.As for the three fractions of the two DHS,XAD-4 fractions contain more aliphatics,carbohydrates,carboxyl groups,and enrich in 13 C with respect to both fulvic and humic acids.Photo-oxidation transformation and contribution from marine-derived DOM were considered as the main reasons resulted in the difference in compositional features for these DHS in this study.     

SEAWATER FLUX OF THE SOUTH CHINA SEA

The South China Sea water can be divided according to depth into three boxes by the pycnoclineand a sill.Using a box model with matter balance,the net seawater fluxes were calculated to be317.9×10~4 m~3/s in box Ⅰ for the upper homogeneous layer outflowing to the adjoining oceans;67×10~4 m~3/s in box Ⅲ for the water entering the basin;240×10~4 m~3/s in box Ⅱ for water entering theSouth China Sea.The upward speed of basin water was calculated to be 8.4×10~(-5) cm/s and that ofseawater flowing up along the pycnocline was calculated to be 8.9×10~(-5) cm/s.     

Electrochemical evaluation of dissolution characteristics of Al-based sacrificial anodes in seawater

The surface dissolution characteristics of Al-based sacrificial anodes in seawater have never been expressed numerically except in words such as uniform dissolution, non-uniform dissolution, serious localized dissolution, etc. An electrochemical method was developed in our laboratory to evaluate the above mentioned characteristics quantitatively. The Al anode samples are polarized to −1000 mv (vs. Ag/AgCl reference electrode) in seawater at 25±1°C, and anodic current-time curves are recorded simultaneously. Then the coulometric density was calculated with the aid of a planimeter. By comparing the coulometric densities of these samples, the surface dissolution characteristics of anodes can be evaluated quantitatively. Contribution No. 1447 from Institute of Oceanology, Academia Sinica     

Seawater flux through Taiwan strait

After the winter and summer current structures on two or three latitudinal sections in Taiwan Strait were obtained from the measured current data, the seawater fluxs through the sections were calculated. In summer, the currents in the central and northern part of Taiwan Strait normally flow northward at a net flux of 3.32×10⁶m³/s. In winter, the high temperature and salinity Kuroshio and South China Sea water enter Taiwan Strait from the southem section at 1.69×10⁶m³/s and 0.59×10⁶ m³/s respectively, while the East China Sea water enters Taiwan Strait from the northern section at 1.02×10⁶m³/s. About 0.40×10⁶ m³/s of the seawater enters the South China Sea along the coast of Fujian and Guangdong; the other 0.62×10⁶ m³/s of the seawater is mixed with the Kuroshio water and the South China Sea water in the northern sea areas. The net northward flux is 1.74×10⁶m³/s in winter.     

Induction of acrosome reaction of spermatozoa in the decapodaEriocheir sinensis

Acrosome reaction in Chinese mitten-handed crab (Eriocheir sinensis) can be induced artificially by adding egg-water, seawater, or CaCl₂ solution. The results show that conditions such as physiological maturity, presence of self-species egg or Ca⁺⁺, alkalinity, or contact, are necessary for the initiation of acrosome reaction. But Ca⁺⁺ may not be an independent agent and the degree of maturity can also affect the induced rate of acrosome reaction. Higher induced rates can be obtained from September to mext April, the highest being in March.     

Effect of Ca(OH)2, NaCl,and Na2SO4 on the corrosion and electrochemical behavior of rebar

The corrosion of rebar in reinforced concrete in marine environments causes significant damage to structures built in ocean environments. Studies on the process and mechanism of corrosion of rebar in the presence of multiple ions may help to control damage and predict the service life of reinforced concrete structures in such environments. The effect of interactions between sulfate and chloride ions and calcium hydroxide on the electrochemical behavior of rebar are also important for evaluation of structure durability. In this work, electrochemical impedance spectroscopy(EIS) plots of rebar in Ca(OH)_2 solution and cement grout, including NaCl and Na_2SO_4 as aggressive salts, were measured for different immersion times. The results show that corrosion of rebar was controlled by the rate of charge transfer as the rebar was exposed to chloride solution. In the presence of high concentrations of sulfate ions in the electrolyte, generation and dissolution of the passive film proceeded simultaneously and corrosion was mainly controlled by the diffusion rate. When Na_2SO_4 and NaCl were added to Ca(OH)_2 solution, the instantaneous corrosion rate decreased by a factor of 10 to 20 as a result of the higher p H of the corroding solution.     

Transfeer of organic pollutants during sewage-seawater mixing

The transfer processes of organic pollutants during sewage-seawater mixing were simulated in three different mixing systems. The release rate of organic matter from sewage particles to seawater was found to be about 0.02–0.04 d⁻¹. The release processes can be simulated by an exchange-equilibrium kinetic model. Degradation of COD was observed in all three mixing systems and can be described by a first order kinetic equation. The degradation rate constantk ranged between 0.04 and 0.07 d⁻¹. These results have provided important parameters for estimation of environmental capacity.     

Photochemical oxidation of benzothiophene in seawater

ＩＮＴＲＯＤＵＣＴＩＯＮｐｈｏｔｏｃｈｅｍｉｃａｌｏｘｉｄａｔｉｏｎｏｆｂｅｎｚｏｔｈｉｏｐｈｅｎｅｉｎｓｅａｗａｔｅｒｉｎｏｒｄｅｒｔｏｌｅａｒｎｍｏｒｅａｂｏｕｔｔｈｅｒｅｍｏｖａｌｐａｔｔｅｒｎｏｆｔｈｉｓｐｏｌｌｕｔａｎｔｉｎｍａｒｉｎｅｅｎｖｉｒｏｎｍｅｎｔｓ.Ｂｅｎｚｏｔｈｉｏｐｈｅｎｅｗａｓｃｈｏｓｅｎｆｏｒｔｈｉｓｓｔｕｄｙｓｉｎｃｅｉｔｉｓｔｈｅｓｉｍｐｌｅｓｔ　　Ｔｈｅｈｉｇｈ -ｐｒｅｓｓｕｒｅｍｅｒｃｕｒｙｌａｍｐｕｓｅｄｉｎｔｈｉｓｓｔｕｄｙｃｏｕｌｄｐｒｏｄｕｃｅｌｉｇ…     

The Influences of Mg^2 ,Ca^2 ,and Mg^2 /Ca^2 Ratio in Mixed Seawater on the Emergence Rate of Penaeus Japonicus Postlarva

This paper reports the approprite ranges of Mg^2 ,Ca^2 and their ratio Mg^2 /Ca^2 in mixed seawater for rearing of Penaeus japonicus larvae,The ranges for the above three indices are 1150-1450mg/L,360-440mg/L and 2.8-3.4,respectively,the proper salinity range of mixed seawater is 22.1-33.9 obtained by mixing estuarine water and concentrated seawater.     

Effect of NH4-non the pigment content ofLaminaria japonica

Experiments withLaminaria japonica were conducted in Meidao Bay and Pier Bay, Qingdao, China, Nitrogen-starved plants were fertilized intermittently with 7.1 mM NH₄−N solution for 1 hour at 3 day intervals, after which chlorophyll a, fucoxanthin, chlorophyll c and β-carotene contents were analyzed. Photosynthetic and growth rates of plants and nitrogen content of seawater were determined. their contents of chlorophyll a, fucoxanthin, chlorophyll c and β-carotene were 1.65, 0.67, 0.33 and 0.06 mg.dm⁻² respectively, or 2.46, 2.03, 1.86 and 1.81 times those of the controls. The ratio of fucoxanthin to chlorophyll a in nitrogen-enriched plants was lower than that of the controls. Normal growth rate of the plants (2 cm·day⁻¹ in length) were reached when the chlorophyll a content exceeded 0.1 mg·g⁻¹ fresh wt., indicating that chlorophyll a content can serve as an indicator of normal growth. Experimental results show that seawater is regarded as fertile for the normal growth ofLaminaria if the total inorganic nitrogen (including ammonium salt, nitrate and nitrite) content in seawater is about 2 μm, and infertile if less than 1 μm, in which case fertilizer should be applied. Contribution No. 1703 from the Institute of Oceanology, Academia Sinica     

Quantitative determination of the salinity of seawater droplet in 10−6 to 10−10 gram

The rate of evaporation of seawater droplets in the air-sea boundary layer can be estimated by its salinity change compared to the sea surface salinity. A micro-chemical method based on Farlow (1954) is developed for quantitative determination of the salinity of an individual droplet without the error due to further evaporation after sampling. A halide ion-sensitive sampling surface is prepared by colloidally dispersing brown silver dichromate into the gelatin layer of a commercially available film. The reaction of soluble chlorides with the silver salt leaves a clear white halo with diametera on the brown film to reveal the volume of the droplet. After the film is developed in a water vapor saturated atmosphere, the halo grows to diameterd with the original as the embryo to indicate the quantity of chloride ion involved in the action. The ratio ofd/(a^1.5) is a function of the salinity of the droplet. The method can be used to determine the salinity of seawater droplet of 10⁻⁶ to 10⁻¹⁰ gram. Details of the principle and preparation, and calibration of the reagent film, are presented. Contribution No. 1708 from the Institute of Oceanology, Academia Sinica. The research was supported by the Chinese National Natural Science Foundation. The paper was prepared while the author was a visiting scholar at the Department of Atmospheric Sciences, AK-40, University of Washington, Seattle, Washington 98195, USA (from May to July, 1989), and Scripps Institution of Oceanography, A-030, University of California, La Jolla, California 92093, USA (from September, 1989 to February, 1990).     

山东烟台大季家地区海水入侵界面划分的意义

在沿海地区划分海水入侵界线具有重大意义,在海水入侵范围内,地下水由于含盐量高,虽然工业生产、人畜生活不能利(饮)用,但深部海水可为海产品养殖业带来较高的利用价值。利用高密度电法和可控源音频大地电磁2种方法准确划分了浅、深部海水入侵界线,并根据电性特征分析探讨了海水入侵区域的由浅至深的侵入特点,推测了不同深度上岩石破碎及富水规律,为探讨沿海养殖业利用温度相对稳定或较高的深部入侵海水进行了积极、有益的探讨。     

Electrochemical behavior of Al—basic sacrificial anode at estuary

The Al—basic sacrificial anode is widely used to protect steel construction from corrosion in seawater, but is not suitable for protecting steel in freshwater. In the estuary area, seawater and freshwater mix and different seawater salinity can be formed in different mixing sites between freshwater and seawater. Based on the requirements of the Shengli Petroleum Administrative Bureau of China, the effect of seawater salinity on electrochemical properties of Al—basic anode was studied under laboratory conditions by the method given in National Standard GB 4948-85 (China Starndard Bureau, 1985). No obvious effect was found when seawater salinity was 30 to 10, but obvious effect on anodic open circuit potential, closed circuit potential and current efficiency was found when seawater salinity was 5. These values are lower than those given in the National Standard. Contribution No. 2681 from the Institute of Oceanology, Chinese Academy of Sciences. This study is a major project (Ky85-11-5) and a key project (A14920416) of the Chinese Academy of Sciences, and also received support from the Shengli Oil Field.