近断层地震动作用下钢筋混凝土桥墩的抗震性能

通过对满足规范延性要求的12根典型钢筋混凝土桥墩试件的线性和非线性地震反应分析，指出在近断层地震动作用下满足延性需求与延性能力比小于1.0的桥墩仍可能发生严重破坏和倒塌，若考虑桥墩的地震损伤性能，允许的延性需求与延性能力比不宜超过0.6-0.8。讨论了桥墩延性抗震设计中强度折减系数Rμ和设计基底剪力系数BSC取值问题。     

MPA方法在不同高度桥墩地震响应分析中的适用性研究

桥梁通常是线路中的控制工程,其抗震性能显得尤为重要。作为梁桥重要组成部分的桥墩,往往是地震作用下容易受到损伤的构件。结合西部山区梁桥的典型桥墩结构形式,基于纤维模型的有限元方法建立桥墩的非线性数值分析模型。采用MPA方法对不同高度桥墩的地震响应进行分析,以非线性时程分析方法的计算结果为基准研究MPA方法的适用性。计算表明MPA方法在分析高阶模态参与程度较高的高墩构件时适用性较差。     

Effects of structural characterizations on fragility functions of bridges subject to seismic shaking and lateral spreading

This paper evaluates the seismic vulnerability of different classes of typical bridges in California when subjected to seismic shaking or liquefaction-induced lateral spreading. The detailed structural configurations in terms of superstructure type, connection, continuity at support and foundation type, etc. render different damage resistant capability. Six classes of bridges are established based on their anticipated failure mechanisms under earthquake shaking. The numerical models that are capable of simulating the complex soil-structure interaction effects, nonlinear behavior of columns and connections are developed for each bridge class. The dynamic responses are obtained using nonlinear time history analyses for a suite of 250 earthquake motions with increasing intensity. An equivalent static analysis procedure is also implemented to evaluate the vulnerability of the bridges when subjected to liquefaction-induced lateral spreading. Fragility functions for each bridge class are derived and compared for both seismic shaking （based on nonlinear dynamic analyses） and lateral spreading （based on equivalent static analyses） for different performance states. The study finds that the fragility functions due to either ground shaking or lateral spreading show significant correlation with the structural characterizations, but differences emerge for ground shaking and lateral spreading conditions. Structural properties that will mostly affect the bridges＇ damage resistant capacity are also identified.     

基于损伤分析的旧曲线梁桥抗震性能评估

曲线桥梁在役期间可能面临地震灾害,导致结构损坏甚至坍塌,为了评估在役桥梁的抗震性能,提出基于损伤分析的曲线梁桥抗震性能评估方法.建立旧曲线梁桥有限元模型,基于损伤分析的原理,提出适合曲线梁桥地震响应特性的构件损伤模型,在全桥有限元模型中输入不同类型地震动,计算各构件的损伤指数,并结合旧桥检算系数,由各构件损伤指数综合得...     

灌浆波纹管装配式桥墩双向地震损伤评价方法

灌浆波纹管连接是装配式墩常用接头连接方式之一,但没有系统研究其受到双向往复荷载作用的整体抗震性能,地震损伤评价方法不够完善。通过双向拟静力试验,研究在双向往复荷载作用状态下灌浆波纹管连接装配式墩的滞回特性变化和破坏模式,讨论了损伤指标构建方法,依据易损性曲线损伤评估了灌浆波纹管装配式墩的抗震性能。结果发现:装配式墩的变形能力和承载能力因双向荷载的耦合效应而急剧下降,装配式墩双向受力损伤状态可以采用Park-Ang值综合反映。在所给加速度情况下,可通过易损性分析得到各装配式墩构件不同损伤状态的超越概率,在峰值加速度一样时,纵桥向损伤状态发生的最大超越概率要比横桥向高。研究结果可以为灌浆波纹管装配式墩双向地震损伤评价提供方法。     

斜交连续刚构桥桥墩地震易损性分析

以美国西部地区某斜交公路连续刚构桥为研究对象，研究其不等高墩易损性差异以及斜交角的改变对桥墩地震易损性的影响。考虑桥梁结构参数和地震动的不确定性，选取100条地震动，沿纵桥向输入，生成"结构-地震动"样本库，以地震动峰值加速度（PGA）为强度指标（IM），利用OpenSees软件对结构进行非线性时程分析得到桥墩动力响应，而后以桥墩曲率延性比衡量桥梁破坏状态，在确定桥墩损伤指标的基础上，采用可靠度理论得到各桥墩的地震易损性曲线，判断桥墩的损伤模式、损伤特点。在此基础上，改变桥梁斜交角度进行易损性分析，得到斜交角变化对桥墩地震易损性的影响。研究表明：该桥最矮墩发生损伤的概率大于其他桥墩，桥墩最先进入塑性的是墩顶和墩底区域；不同斜交角对桥墩的地震响应影响显著，各墩损伤破坏排序与斜交桥结构构造特点有关，同一排架墩的两侧墩柱易损性呈现与角度变化趋势相反的排列，损伤越严重，趋势越明显；对于此不等高的斜交刚构桥，最矮墩为其抗震薄弱环节，斜交角越大，越应该关注钝角处矮墩的损伤情况，并提高其设计标准，在进行斜交刚构桥抗震设计中应予以重视。     

A comparative study between China and U.S. on seismic design philosophy and practice of a long span arch bridge

This paper presents the first of a series of case studies on the seismic design of long span bridges （cable-stayed bridges, suspension bridges and arch bridges） under a cooperative research project on seismic behavior and design of highway bridges between the State Key Laboratory for Disaster Reduction in Civil Engineering, Tongji University and the Multidisciplinary Center for Earthquake Engineering Research, University at Buffalo. The objective of this series of case studies is to examine the differences and similarities on the seismic design practice of long span bridges in China and the U.S., to identify research needs and to develop design guidelines beneficial to bridge engineers in both countries. Unlike short to medium span bridges, long span bridges are not included in most seismic design specifications, mainly because they are location dependent and structurally unique. In this paper, an available model of a steel tied half through arch bridge with a main span of 550m in China is discussed. Analysis is focused on comparisons of the seismic responses due to different ground motions. Seismic design criteria and seismic performance requirements for long span bridges in both countries were first introduced and compared, and then three near field earthquake records with large vertical components were selected as the excitations to examine the seismic behavior and seismic vulnerability of the bridge. Results show that （1） the selected near field ground motions cause larger responses to key components （critical sections） of the bridge （such as arch rib ends） with a maximum increase of more than twice those caused by the site specific ground motions; （2） piers, longitudinal girders and arch crowns are more vulnerable to vertical motions, especially their axial forces; and （3） large vertical components of near field ground motions may not significantly affect the bridge＇s internal forces provided that their peak acceleration spectra ordinates only appear at periods of less than 0.2s. However, they may have more influence on the longitudinal displacements of sliding bearings due to their large displacement spectra ordinates at the fundamental period of the bridge.     

Seismic performance of an unreinforced masonry building: An experimental investigation

This paper presents the results of an experimental investigation carried out to investigate the seismic performance of a two storey brick masonry house with one room in each floor. A half‐scale building constructed using single wythe clay brick masonry laid in cement sand mortar and a conventional timber floor and timber roof clad with clay tiles was tested under earthquake ground motions on a shaking table, first in the longitudinal direction and then in the transverse direction. In each direction, the building was subjected to different ground motions with gradually increasing intensity. Dynamic properties of the system were assessed through white‐noise tests after each ground motion. The building suffered increasing levels of damage as the excitations became more severe. The damage ranged from cracking to global/local rocking of different piers and partial out‐of‐plane failure of the walls. Nevertheless, the building did not collapse under base excitations with peak ground acceleration up to 0.8g. General behaviour of the tested building model during the tests is discussed, and fragility curves are developed for unreinforced masonry buildings based on the experimental results. Copyright © 2009 John Wiley & Sons, Ltd.     

Evaluation of code criteria for bridges with unequal pier heights

One of the challenges associated with Eurocode 8 and AASHTO-LRFD is predicting the failure of irregular bridges supported by piers of unequal heights. EC8 currently uses “moment demand-to-moment capacity” ratios to somewhat guarantee simultaneous failure of piers on bridges, while AASHTO-LRFD relies on the relative effective stiffness of the piers. These conditions are not entirely valid, in particular for piers with a relative height of 0.5 or less, where a possible combination of flexure and shear failure mode may occur. In this case, the shorter piers often result in brittle shear failure, while the longer piers are most likely to fail due to flexure, creating a combination of different failure modes experienced by the bridge. To evaluate the adequacy of EC8 design procedures for regular seismic behavior, various irregular bridges are simulated through a non-linear pushover analysis using shear-critical fiber-based beam-column elements. The paper investigates the behavior of irregular monolithic and bearing-type bridges experiencing different failure modes, and proposes different methods for regularizing the bridge performance to balance damage. The ultimate aim is to obtain a simultaneous or near-simultaneous failure of all piers irrespective of the different heights and failure mode experienced.     

基于IDA的高墩大跨桥梁抗震性能评估

高墩桥梁的地震响应与传统的中低墩桥梁有很大差别,我国现行桥梁抗震规范对此没有规定。为了合理评估高墩大跨桥梁的抗震性能,以一座连续刚构桥为研究对象,采用OpenSees建立弹塑性有限元动力分析模型,从PEER地震数据库中选取了15条地震记录进行增量动力分析(Incre-mental dynamic analysis,IDA),利用Ramberg-Osgood函数对控制参数进行统计,从而得到了结构概率分位值为10%、50%和90%的IDA曲线,结合定义的损伤状态对结构的抗震性能进行了评估;根据墩身最大曲率分布得到了塑性区域长度,提出了根据最大曲率分布估算墩顶目标位移的方法。结果表明:利用R-O函数统计得到的IDA概率分位曲线能很好地体现桥梁抗震性能,并能给出满足相应性能水准的可靠等级。在强震作用下,高墩结构塑性区域长度与各国规范计算结果吻合,按墩身最大曲率分布估算墩顶位移与IDA分析结果吻合较好,弥补了规范的不足。     

强震下斜交桥地震反应与减隔震性能分析

针对斜交桥在破坏性地震中发生破坏和损伤的突出问题,采用铅芯橡胶支座(LRB)进行隔震和滞回耗能。基于OpenSees平台建立了不同斜度的传统非隔震和全桥采用LRB隔震的4跨斜交连续梁桥动力分析模型,沿2个水平方向输入远场地震动和具有向前方向性效应、滑冲效应以及无速度脉冲效应的近断层地震动,并进行非线性时程计算,研究桥墩和挡块的损伤状态、主梁旋转度、碰撞力与斜交桥斜度的关系以及LRB对斜交桥抗震性能的影响。结果表明:向前方向性效应和滑冲效应的脉冲型地震动作用下的斜交桥地震反应和损伤明显大于无速度脉冲近断层和远场地震动作用; 采用LRB隔震后,明显降低了固定墩的地震损伤,桥墩位移减震率可达到50%以上; LRB隔震桥主梁与挡块的间隙宜结合桥梁的地震风险和设计位移进行确定。     

Energy capacity and seismic performance of RC waffle-flat plate structures under two components of far-field ground motions: Shake table tests

The bidirectional response of a portion of a reinforced concrete (RC) waffle-flat plate (WFP) structure subjected to far-field ground motions is studied through shake table tests. The test specimen is a scaled portion of a prototype structure designed under current building codes and located in a region of moderate seismicity of the Mediterranean area. The specimen was subjected to a sequence of tests of increasing acceleration amplitude that respectively represented very frequent, frequent, design, and very rare earthquakes at the site. The test structure performed well (basically in the elastic domain) under very frequent and frequent earthquakes, approached the boundary between the performance levels of life safety and near collapse under the design earthquake, and collapsed under the very rare earthquake. Damage concentrated at column bases and at the transverse beams of the exterior plate-to-column connection. Columns dissipated about 10% of the total energy that contributes to damage, and the rest was dissipated by the exterior plate-column connection. The total energy input on the structure until collapse under the bidirectional seismic action was very close to the value obtained in previous studies on a similar specimen tested under unidirectional ground motions. The capacity curve estimated from the experimental base shear vs top displacement relationship suggests it is best to use a behavior factor of at most q = 2 when designing WFP structures with the reduced-spectrum force-based approach.     

Hybrid simulation of a multi‐span RC viaduct with plain bars and sliding bearings

This paper deals with the seismic response assessment of an old reinforced concrete viaduct and the effectiveness of friction‐based retrofitting systems. Emphasis was laid on an old bridge, not properly designed to resist seismic action, consisting of 12 portal piers that support a 13‐span bay deck for each independent roadway. On the basis of an OpenSEES finite element frame pier model, calibrated in a previous experimental campaign with cyclic displacement on three 1:4 scale frame piers, a more complex experimental activity using hybrid simulation has been devised. The aim of the simulation was twofold: (i) to increase knowledge of non‐linear behavior of reinforced concrete frame piers with plain steel rebars and detailing dating from the late 1950s; and (ii) to study the effectiveness of sliding bearings for seismic response mitigation. Hence, to explore the performance of the as built bridge layout and also of the viaduct retrofitted with friction‐based devices, at both serviceability and ultimate limit state conditions, hybrid simulation tests were carried out. In particular, two frame piers were experimentally controlled with eight‐actuator channels in the as built case while two frame piers and eight sliding bearings were controlled with 18‐actuator channels in the isolated case. The remaining frame piers were part of numerical substructures and were updated offline to accurately track damage evolution. Copyright © 2015 John Wiley & Sons, Ltd.     

Ductile steel plate external end diaphragms for steel tub girder straight highway bridges

The end diaphragm of bridges are normally designed to resist lateral seismic forces imposed on the superstructure in earthquake prone regions. Using ductile diaphragms with high deformation capacity could reduce the seismic demands on the substructure and prevent costly damage under strong ground motions. The end diaphragms of steel tub girder bridges with high lateral stiffness and dominant shear behavior have a potential to be used as ductile fuse elements. In this study, a steel plate shear diaphragm(SPSD) is introduced as an external end diaphragm of tub girder steel bridges to reduce the seismic demands imposed on the substructure. Quasi static nonlinear analyses were conducted to evaluate responses of sixteen SPSDs with different boundary conditions, aspect ratios and diaphragm plate thicknesses. Moreover, nonlinear time history analyses were performed using three different ground motions corresponding to DBE and MCE level spectrums. Cyclic and time history analyses proved the proper behavior of SPSD and its efficiency to reduce seismic demands by more than 25%.     

Shake table test and numerical study of self‐centering steel frame with SMA braces

Given their excellent self‐centering and energy‐dissipating capabilities, superelastic shape memory alloys (SMAs) become an emerging structural material in the field of earthquake engineering. This paper presents experimental and numerical studies on a scaled self‐centering steel frame with novel SMA braces (SMAB), which utilize superelastic Ni–Ti wires. The braces were fabricated and cyclically characterized before their installation in a two‐story one‐bay steel frame. The equivalent viscous damping ratio and ‘post‐yield’ stiffness ratio of the tested braces are around 5% and 0.15, respectively. In particular, the frame was seismically designed with nearly all pin connections, including the pinned column bases. To assess the seismic performance of the SMA braced frame (SMABF), a series of shake table tests were conducted, in which the SMABF was subjected to ground motions with incremental seismic intensity levels. No repair or replacement of structural members was performed during the entire series of tests. Experimental results showed that the SMAB could withstand several strong earthquakes with very limited capacity degradation. Thanks to the self‐centering capacity and pin‐connection design, the steel frame was subjected to limited damage and zero residual deformation even if the peak interstory drift ratio exceeded 2%. Good agreement was found between the experimental results and numerical simulations. The current study validates the prospect of using SMAB as a standalone seismic‐resisting component in critical building structures when high seismic performance or earthquake resilience is desirable under moderate and strong earthquakes. Copyright © 2016 John Wiley & Sons, Ltd.     

Convex model-based calculation of robust seismic fragility curves of isolated continuous girder bridge

The convex model approach is applied to derive the robust seismic fragility curves of a five-span isolated continuous girder bridge with lead rubber bearings (LRB) in China. The uncertainty of structure parameters (the yield force and the post-yield stiffness of LRB, the yield strength of steel bars, etc.) are considered in the convex model, and the uncertainty of earthquake ground motions is also taken into account by selecting 40 earthquake excitations of peak ground acceleration magnitudes ranging from 0.125 to 1.126 g. A 3-D finite element model is employed using the software package OpenSees by considering the nonlinearity in the bridge piers and the isolation bearings. Section ductility of piers and shearing strain isolation bearings are treated as damage indices. The cloud method and convex model approach are used to construct the seismic fragility curves of the bridge components (LRB and bridge piers) and the bridge system, respectively. The numerical results indicate that seismic fragility of the bridge system and bridge components will be underestimated without considering the uncertainty of structural parameters. Therefore, the failure probability P _f,max had better be served as the seismic fragility, especially, the fragility of the bridge system is largely dictated by the fragility of LRB. Finally, the probabilistic seismic performance evaluation of the bridge is carried out according to the structural seismic risk estimate method.     

Experimental testing and numerical modelling of a heavy timber moment‐resisting frame with ductile steel links

This paper presents the development, experimental testing, and numerical modelling of a new hybrid timber‐steel moment‐resisting connection that is designed to improve the seismic performance of mid‐rise heavy timber moment‐resisting frames (MRF). The connection detail incorporates specially designed replaceable steel links fastened to timber beams and columns using self‐tapping screws. Performance of the connection is verified through experimental testing of four 2/3 scale beam‐column connections. All 4 connection specimens met the acceptance criteria specified in the AISC 341‐10 provisions for steel moment frames and exhibit high strength, ductility, and energy dissipation capacity up to storey drifts exceeding 4%. All of the timber members and self‐tapping screw connections achieved their design objective, remaining entirely elastic throughout all tests and avoiding brittle modes of failure. To assess the global seismic performance of the newly developed connection in a mid‐rise building, a hybrid timber‐steel building using the proposed moment‐resisting connection is designed and modelled in OpenSees. To compare the seismic performance of the hybrid MRF with a conventional steel MRF, a prototype steel‐only building is also designed and modelled in OpenSees. The building models are subject to a suite of ground motions at design basis earthquake and maximum credible earthquake hazard levels using non‐linear time history analysis. Analytical results show that drifts and accelerations of the hybrid building are similar to a conventional steel building while the foundation forces are significantly reduced for the hybrid structure because of its lower seismic weight. The results of the experimental program and numerical analysis demonstrate the seismic performance of the proposed connection and the ability of the hybrid building to achieve comparable seismic performance to a conventional steel MRF.     

局部锈蚀矩形RC墩重度震损后加固试验研究

为探究局部锈蚀矩形截面钢筋混凝土（RC）桥墩重度震损加固后的抗震性能,本文对拟静力破坏后的6个矩形截面RC桥墩试件进行扩大截面加固。通过加载试验,对加固桥墩试件从破坏形态、滞回特性、水平承载力、位移延性、侧向刚度以及耗能等方面进行了系统分析。结果表明:相比于普通箍筋,横向施加预应力的改进扩大截面加固方式对破坏后桥墩试件的抗震性能修复成效更佳;在同等位移幅值下,锈蚀率不断增大,桥墩试件抗震性能呈现逐渐降低的趋势;钢筋锈蚀位置上移,加固后桥墩试件的抗震性能提升;轴压比加大,加固后桥墩试件承载力和侧向刚度增大,但延性降低。