Biosorption of Methylene Blue from Aqueous Solution Using a Bioenergy Forest Waste: Xanthoceras sorbifolia Seed Coat

Xanthoceras sorbifolia seed coat (XSSC), a bioenergy forest waste, was used for the adsorption of methylene blue (MB) from aqueous solutions. The effects of adsorbent dosage, pH, adsorbate concentration and contact time on MB biosorption were studied. The equilibrium adsorption data was analyzed by Langmuir and Freundlich isotherm models. The results indicated that the Langmuir model provided the best correlation with the experimental data. The adsorption capacity of XSSC for MB was determined with the Langmuir model and was found to be 178.6 mg/g at 298 K. The adsorption kinetic data was modeled using the pseudo‐first order, pseudo‐second order, and intraparticle diffusion kinetic equations. It was seen that the pseudo‐second order equation could describe the adsorption kinetics, and intraparticle diffusion was not the sole rate controlling factor. Thermodynamic parameters were also evaluated. Standard Gibbs free energy was spontaneous for all interactions, and the biosorption process exhibited exothermic standard enthalpy values. The results indicated that XSSC is an attractive alternative for removing cationic dyes from wastewater.     

Adsorption Characteristics of Reactive Black 5 from Aqueous Solution onto Chitosan

Adsorption of reactive black 5 (RB5) from aqueous solution onto chitosan was investigated in a batch system. The effects of solution pH, initial dye concentration, and temperature were studied. Adsorption data obtained from different batch experiments were modeled using both pseudo first‐ and second‐order kinetic equations. The equilibrium adsorption data were fitted to the Freundlich, Tempkin, and Langmuir isotherms over a dye concentration range of 45–100 µmol/L. The best results were achieved with the pseudo second‐order kinetic and Langmuir isotherm equilibrium models, respectively. The equilibrium adsorption capacity (q_e) was increased with increasing the initial dye concentration and solution temperature, and decreasing solution pH. The chitosan flakes for the adsorption of the dye was regenerated efficiently through the alkaline solution and was then reused for dye removal. The activation energy (E_a) of sorption kinetics was estimated to be 13.88 kJ/mol. Thermodynamic parameters such as changes in free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) were evaluated by applying the van't Hoff equation. The thermodynamics of reactive dye adsorption by chitosan indicates its spontaneous and endothermic nature.     

Removal of Various Phenoxyalkanoic Acid Herbicides from Water by Organo‐clays

Dodecylammonium bentonite (DB) and dodecylammonium sepiolite (DS) were used as sorbents for phenoxyalkanoic acid herbicides 2,4‐D ((2,4‐dichlorophenoxy)acetic acid), 2,4‐DP ((RS)‐2‐(2,4‐dichlorophenoxy)propionic acid), 2,4‐DB (4‐(2,4‐dichlorophenoxy)butyric acid), 2,4,5‐T ((2,4,5‐trichlorophenoxy)acetic acid), and MCPA ((4‐chloro‐2‐methylphenoxy)acetic acid). Langmuir, Freundlich, and the linear Henry’s Law isotherm adsorption parameters were calculated from the adsorption isotherms. Langmuir equation showed poor fit for both adsorbents. According to the evaluation using the Freundlich equation, the DS sample showed much higher and stronger sorption capacity than DB. Similar behaviour was also observed in the case of the linear Henry’s Law isotherm. The adsorption of the herbicides on both DB and DS decreased in the order of 2,4‐DB > 2,4,5‐T > 2,4‐DP > 2,4‐D > MCPA.     

Modification of MCM‐41 with Anionic Surfactant: A Convenient Design for Efficient Removal of Cationic Dyes from Wastewater

The potential of MCM‐41 for the removal of cationic dyes from water solution was evaluated using sodium dodecyl sulfate (SDS) for the surface modification of this mesoporous material. Admicelle structures formed on the surface of the calcined MCM‐41 are capable of removing organic pollutants and cationic species from water environment. The structural, textural, and surface chemical characteristics of the prepared SDS‐modified MCM‐41 (SDS‐MCM‐41) were studied. The adsorption capacity of SDS‐MCM‐41 was evaluated for methylene blue (MB) as a target cationic dye. Equilibrium adsorption isotherm data were manipulated employing nonlinear regression analysis. The Langmuir, Freundlich, and Sips isotherm models were examined. The adsorption data were well fitted to both Langmuir and Sips isotherm models. The maximum adsorption capacity of SDS‐MCM‐41 for MB, based on Langmuir and Sips models, were 290.8 and 297.3 mg g^?1, respectively. Ethanol was found to be an effective solvent for partial regeneration of the adsorbent.     

Studies on the Removal of Iron from Drinking Water by Electrocoagulation – A Clean Process

The present study describes an electrocoagulation process for the removal of iron from drinking water using magnesium as the anode and galvanized iron as the cathode. Experiments were carried out as a function of pH, temperature and current density. The adsorption capacity was evaluated using both the Langmuir and the Freundlich isotherm models. The results show that the maximum removal efficiency of 98.4% was achieved at a current density of 0.06 A dm^–2, at a pH of 6.0. The adsorption of iron was better explained by fitting the Langmuir adsorption isotherm, which suggests a monolayer coverage of adsorbed molecules. The adsorption process followed a second‐order kinetics model. Temperature studies showed that adsorption was endothermic and spontaneous in nature.     

Preparation,Characterization and Adsorption Mechanism of Cu(II) onto Protonated Rubber Leaf Powder

The adsorption of Cu(II) onto HCl treated rubber leaf powder (HHBL) was investigated in batch and column studies. The adsorbent was characterized by spectroscopic and quantitative analyses in order to understand the mechanism of copper adsorption. HHBL is mesoporous in nature as indicated by Bruneuer, Emmett and Teller (BET) analysis, and has various kinds of functional groups such as Si‐OH, ROH, RCOOH, RCOO^–, RNH₂, C‐O‐C and aromatic rings as detected by Fourier transform infrared (FTIR) spectroscopy. Copper adsorption was confirmed by scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy (EDS). The equilibrium process was described well by the Langmuir isotherm model, and a maximum adsorption capacity of 8.39 mg/g was recorded for the smallest adsorbent size (<180 μm). The two main adsorption mechanisms involved were ion exchange and complexation. The fixed bed column study demonstrated satisfactory applicability of HHBL in removing Cu(II) from aqueous solutions.     

Isotherm Study of Phosphorus Uptake from Aqueous Solution Using Aluminum Oxide

Aluminum oxide, which could be an alternative filter media for phosphorus uptake from aqueous solution, was selected as an adsorbent for the isotherm study of phosphorus uptake from aqueous solution. Batch method was adopted to investigate the adsorption behavior of phosphorus onto aluminum oxide. The Langmuir, Freundlich, and Redlich–Peterson isotherms were used to analyze the experimental data by both the linear and nonlinear regression methods. The adsorption experiment was conducted at various temperatures, to choose the appropriate method and obtain the creditable adsorption parameters for phosphorus uptake studies. The results indicated that the nonlinear regression method might be a better way to compare the best‐fitting isotherm and obtain the parameters for the adsorption of phosphorus onto aluminum oxide. Both the Redlich–Peterson and the Freundlich isotherms have high coefficients of determination for the adsorption of phosphorus onto aluminum oxide at various temperatures. In addition, a new relationship between the Redlich–Peterson and the Freundlich isotherm parameters was presented.     

Dye Removal from Colored Textile Wastewater by Poly(propylene imine) Dendrimer: Operational Parameters and Isotherm Studies

This paper deals with the removal of textile dyes from aqueous solutions by poly(propylene imine) dendrimer (PPI). Direct red 80 (DR80), Acid Green 25 (AG25), Acid Blue 7 (AB7), and Direct Red 23 (DR23) were used as model dyes. The effects of operational parameters on dye removal such as dendrimer concentration, dye concentration, salt (inorganic anions), and pH have been studied at 25°C. The Langmuir and Freundlich isotherm models were investigated. In addition, dye desorption of dendrimer was studied. The results indicated that acidic pH supported the adsorption of dyes by dendrimer. Furthermore studies of dye concentration and salt effects exhibited that dye removal percentage by dendrimer was decreased. It was found that the isotherm data of DR80, AG25, and DR23 followed Langmuir isotherm and isotherm data of AB7 followed Freundlich isotherm models. Desorption tests showed that maximum dye releasing of 76.5% for DR80, 84.5% for AG25, 87% for AB7, and 93% for DR23 were achieved in aqueous solution at pH 12. Based on the data of present study, one could conclude that the dendrimer being an environmentally friendly adsorbent with relatively large adsorption capacity might be a suitable alternative for elimination of dyes from colored textile wastewater.     

Competitive Adsorption of Nickel and Copper Ions from Aqueous Solution Using Nonliving Biomass of the Marine Brown Alga Laminaria japonica

The adsorption of nickel and copper in a bicomponent system using the nonliving biomass of the marine brown alga Laminaria japonica was investigated in batch systems as a function of initial solution pH, contact time and temperature. The adsorption of nickel and copper was strongly pH dependent. Kinetic studies pointed to a rapid uptake with an equilibrium time of about 30 min. The kinetic curves were successfully fitted by linear regression to pseudo first and pseudo‐second‐order equations. The equilibrium data was analyzed using several models, including the extended Langmuir equation, modified extended Langmuir model and combined extended Langmuir‐Freundlich model. The results suggested that the competitive adsorption of nickel and copper at all temperatures was best represented by the combined extended Langmuir‐Freundlich isotherm. The isotherms indicated competitive uptake, with copper being preferentially adsorbed followed by nickel with an increase in the amount of solute in solution. Thermodynamic analysis revealed that the simultaneous adsorption of nickel and copper ions could be considered to be a spontaneous, endothermic process, with increased randomness.     

Adsorption Kinetic and Equilibrium Studies on Removal of Lead(II) onto Glutamic Acid/Sepiolite

In this study, a modified method was used to increase the adsorption of lead ions from aqueous solutions by using modified clay mineral on the laboratory scale. Adsorption experiments have been carried out on the use of both thermal activated sepiolite (TAS) and their glutamate/sepiolite modification (GS) as adsorbents. The experimental data was analyzed using adsorption kinetic models (pseudo first‐ and second‐order equations). The pseudo second‐order kinetic model fitted well to the kinetic data (R² ≥ 0.99). Then, the Freundlich and Langmuir models were applied to describe the uptake of Pb(II) on GS and the Langmuir isotherm model agrees well with the equilibrium experimental data (R² ≥ 0.97). The maximum adsorption capacity was observed to be 128.205 mg/g by GS according to the Langmuir equation. Desorption efficiency of the GS was studied by the batch method using EDTA, HCl, and HNO₃ solutions. Desorption of 69.18, 74.55, and 80% of Pb(II) from GS was achieved with 0.1 M EDTA, 0.1 M HCl, and 0.1 M HNO₃ solutions, respectively. FTIR analysis suggests the importance of functional groups such as amino, hydroxyl, and carboxyl during Pb(II) removal. SEM observations demonstrated that an important interaction at the lead‐modified sepiolite interface occurred during the adsorption process. In addition, the thermodynamic constants was calculated that the values of the Gibbs free energy (ΔG*), enthalpy (ΔH*), and entropy (ΔS*) of modification were 86.79 kJ/mol, ?18.91 kJ/mol, and ?354.70 J/mol/K, respectively. The negative value of ΔH* shows exothermic nature of adsorption.     

Adsorption of Thallium(I) Ions Using Eucalyptus Leaves Powder

Using batch method, the adsorption of thallium(I) ions from aqueous solutions on eucalyptus leaves powder, as a low cost adsorbent, was studied. The effect of various modification of considered adsorbent on the adsorption percentage of Tl(I) is an important feature of this study. The results showed that the unmodified and acidic modified adsorbent are the poor adsorbents for the Tl(I) ions while basic modified adsorbent is a suitable adsorbent. Also, the effect of some experimental conditions such as solution initial pH, agitation speed, contact time, sorbent dosage, temperature, particle size, and thallium initial concentration was studied. The results showed that the adsorption percentage depends on the conditions and the process is strongly pH‐dependent. The satisfactory adsorption percentage of Tl(I) ions, 81.5%, obtained at 25 ± 1°C. The equilibrium data agreed fairly better with Langmuir isotherm than Freundlich and Temkin models. The value of q_m that was obtained by extrapolation method is 80.65 mg g^?1. Separation factor values, R_L, showed that eucalyptus leaves powder is favorable for the sorption of Tl(I). The negative values of ΔH⁰ and ΔS⁰ showed that the Tl(I) sorption is an exothermic process and along with decrease of randomness at the solid–solution interface during sorption, respectively.     

Assessment of the Biosorption Characteristics of a Spent Cottonseed Husk Substrate for the Decolorization of Methylene Blue

This study concentrates on the possible application of the spent cottonseed husk substrate (SCHS), an agricultural waste used after the cultivation of white rot fungus Flammulina velutipes, to adsorb methylene blue (MB) from aqueous solutions. Batch studies were carried out with variable initial solution pH, adsorbent amount, reaction time, temperature, and initial MB concentration. MB uptake was favorable at pH ranging from 4.0 to 12.0, and the equilibrium adsorption capacity of 143.5 mg g^?1 can be reached promptly within about 240 min. The combination analysis of FTIR and BET techniques revealed that the massive functional groups on the biosorbent surface, such as hydroxyl and carboxyl, were responsible for the biosorption of MB. It was found that adsorption data matched the pseudo‐second order kinetic and Langmuir isotherm models. Thermodynamic parameters of free energy (ΔG°), enthalpy (ΔH°), and entropy (ΔS°), obtained from biosorption MB ranging from 293 to 313 K, showed that the sorption experiment was a spontaneous and endothermic process. The study highlighted a new pathway to develop a new potential utilization of SCHS as a low‐cost sorbent for the removal of MB pollutants from wastewater.     

Enhancement of Carbon Dioxide Capture by Amine‐Functionalized Multi‐Walled Carbon Nanotube

In this study, crude multi‐walled carbon nanotubes (MWCNT) was functionalized by a two‐step process; first using strong mixed acids (H₂SO₄/HNO₃) and then treatment with 1,3‐phenylenediamine (mPDA). The equilibrium adsorption of CO₂ on pristine MWCNT and amine functionalized MWCNT (MWCNT‐NH₂) were investigated. Experiments were preformed via application of volumetric method in a dual sorption vessel at temperature range of 298–318 K and pressures up to 40 bars. The results obtained indicated that the equilibrium uptake of CO₂ increased after functionalizing of MWCNT. The increase in CO₂ capture by MWCNT‐NH₂ was attributed to the existence of great affinity between CO₂ molecules and amine sites on this adsorbent at low pressures. The experimental data were analyzed by means of Freundlich and Langmuir adsorption isotherm models. The data obtained revealed a fast kinetics for the adsorption of CO₂ in which most of adsorption occurred at initial period of adsorption experiments. This renders MWCNT as a suitable adsorbent for practical applications. Values of isosteric heat of adsorption were evaluated based on Clausius–Clapeyron equation. The results demonstrated that both chemisorption and physisorption played important role in CO₂ adsorption on MWCNT‐NH₂, whereas the physisorption process was dominant for CO₂ adsorption on MWCNT.     

Copper(II) Biosorption on Soda Lignin From Oil Palm Empty Fruit Bunches (EFB)

The adsorption of Cu(II) ions from aqueous solutions by soda lignin as an absorbent using a batch adsorption system is presented in this paper. The soda lignin used in this study was extracted from black liquor derived from oil palm empty fruit bunches (EFB) using 20% v/v sulfuric acid. The effects of varying experimental parameters such as pH value, adsorbent dosage, different concentrations of Cu(II) ions, and agitation period were investigated. The results revealed that the optimum adsorption of Cu(II) onto soda lignin was recorded at a pH of 5.0 at an adsorbent dosage of 0.5 g soda lignin and an agitation period of 40 min. The adsorption capacities and rates of Cu(II) ions onto soda lignin was evaluated. The Langmuir and Freundlich adsorption models were applied to calculate the isotherm constants. It was found that the adsorption isothermal data could be well interpreted by the Freundlich model. The kinetic experimental data properly correlated with the pseudo‐second‐order kinetic model, which implies that chemical sorption is the rate‐limiting step.     

Adsorption Kinetics,Isotherms, and Desorption of Monocrotophos and Dichlorvos on Various Indian Soils

Pesticide sorption on to the soil has a significant role in deciding the fate and behavior of pesticides in soil and aquatic environment. The present study investigates the adsorption of monocrotophos (MCP) and dichlorvos (DDVP) on the three soils of Malwa region of Punjab, India under different conditions. Batch adsorption experiments were preformed in replicates using 2 g of air‐dried soil and varying concentrations of pesticides and 20 mL of 0.01 M CaCl₂ as background electrolyte. The results revealed high adsorption of MCP and DDVP in soil B with k_f‐values 0.1261 and 0.0498 and n‐values 2.7345 and 1.831, respectively. The adsorption isotherms obtained were analyzed and the data was subjected to classical Langmuir, Freundlich, and Temkin models. The experimental data best fitted to the logarithm form of Freundlich and Temkin model. Kinetics analyses were performed using pseudo‐first order, pseudo‐second order, and intraparticle diffusion models. The regression results showed that the experimental data fitted very well with the pseudo‐second order kinetic model as correlation coefficient value is very closer to 1 and also followed the intraparticle diffusion model, whereas, diffusion is not only the rate controlling step. The percentages desorption with tap and distilled water is 32–64% for MCP and 25–48% for DDVP.     

Removal of Copper,Nickel, and Zinc Ions from Electroplating Rinse Water

Removal of copper, nickel, and zinc ions from synthetic electroplating rinse water was investigated using cationic exchange resin (Ceralite IR 120). Batch ion exchange studies were carried out to optimize the various experimental parameters (such as contact time, pH, and dosage). Influence of co‐existing cations, chelating agent EDTA on the removal of metal ion of interest was also studied. Sorption isotherm data obtained at different experimental conditions were fitted with Langmuir, Freundlich, Redlich–Peterson, and Toth models. A maximum adsorption capacity of 164 mg g^?1 for Cu(II), 109 mg g^?1 for Ni(II), and 105 mg g^?1 for Zn(II) was observed at optimum experimental conditions according to Langmuir model. The kinetic data for metal ions adsorption process follows pseudo second‐order. Presence of EDTA and co‐ions markedly alters the metal ion removal. Continuous column ion exchange experiments were also conducted. The breakeven point of the column was obtained after recovering effectively several liters of rinse water. The treated rinse water could be recycled in rinsing operations. The Thomas and Adams–Bohart models were applied to column studies and the constants were evaluated. Desorption of the adsorbed metal ions from the resin column was studied by conducting a model experiments with Cu(II) ions loaded ion exchange resin column using sulfuric acid as eluant. A novel lead oxide coated Ti substrate dimensionally stable (DSA) anode was prepared for recovery of copper ions as metal foil from regenerated liquor by electro winning at different current densities (50–300 A cm^?2).     

Removal of Chromium from Synthetic Effluent using Nymphaea rubra

In the present work, biosorption of Cr(VI) by Nymphaea rubra was investigated in batch studies. Batch experiments were conducted to study the effect of initial sorbent dosage, solution pH and initial Cr(VI) concentration. The results showed that the equilibrium uptake capacity was increased with decrease in biomass dosage. The Cr(VI) removal was influenced by the initial chromium compound concentration. Langmuir and Freundlich adsorption isotherm models were used to represent the equilibrium data. The Freundlich isotherm model was fitted very well with the equilibrium data when compared to Langmuir isotherm model. The sorption results were analyzed for pseudo‐first order and pseudo‐second order kinetic model. It was observed that the kinetic data fitted very well with the pseudo‐second order rate equation when compared to the pseudo‐first order rate equation. Fourier transform infrared spectrum showed the presence of different functional groups in the biomass. The surface morphology of the sorbent was exemplified by SEM analysis. Aquatic weeds seem to be a promising biosorbent for the removal of chromium ions from water environment. This paper reports the research findings of a laboratory‐based study on the removal of Cr(VI) from the synthetic solution using the dried stem of N. rubra as a biosorbent.     

Removal of Pyridine from Aqueous Solution by Adsorption on an Activated Carbon Cloth

Pyridine is a very toxic pollutant that has to be removed from wastewater. In this work, adsorption of pyridine on activated carbon cloth (ACC) is studied as a possible alternative for eliminating pyridine from aqueous solution. The ACC was produced from polyacrylonitrile. The adsorption equilibrium data of pyridine on ACC was obtained in a batch adsorber. The experimental data was interpreted with the isotherms of Langmuir, Freundlich, and Prausnitz‐Radke (PR), and the PR isotherm better represented the experimental data. The capacity of ACC for adsorbing pyridine was favored increasing the solution pH from 3 to 6, and this effect was due to the π–π dispersive and electrostatic interactions between the pyridine species in solution and the surface complexes of ACC. The modified Langmuir model fitted reasonably well the influence of pH on the adsorption capacity. In this model was assumed that both neutral pyridine and pyridinium were simultaneously adsorbed on ACC accordingly to the experimental results. The adsorption capacity was almost independent of temperature. The reversibility study revealed that 75% of the pyridine can be desorbed from ACC indicating that part of the pyridine was irreversibly adsorbed, and possibly chemisorbed.     

Adsorption of Metal Ions onto the Chemically Modified Agricultural Waste

This paper discusses about the adsorption of metal ions such as Cu(II), Cd(II), Zn(II), and Ni(II) from aqueous solution by sulfuric acid treated cashew nut shell (STCNS). The adsorption process depends on the solution pH, adsorbent dose, contact time, initial metal ions concentration, and temperature. The adsorption kinetics was relatively fast and equilibrium was reached at 30 min. The adsorption equilibrium follows Langmuir adsorption isotherm model. The maximum adsorption capacity values of the modified cashew nut shell (CNS) for metal ions were 406.6 mg/g for Cu(II), 436.7 mg/g for Cd(II), 455.7 mg/g for Zn(II), and 456.3 mg/g for Ni(II). The thermodynamic study shows the adsorption of metal ions onto the STCNS was spontaneous and exothermic in nature. The kinetics of metal ions adsorption onto the STCNS followed a pseudo‐second‐order kinetic model. The external mass transfer controlled metal ions removal at the earlier stages and intraparticle diffusion at the later stages of adsorption. A Boyd kinetic plot confirms that the external mass transfer was the slowest step involved in the adsorption of metal ions onto the STCNS. A single‐stage batch adsorber was designed using the Langmuir adsorption isotherm equation.     

Removal of Cadmium from Aqueous Solution Using Castor Seed Hull: A Kinetic and Equilibrium Study

The effects of various parameters such as initial concentration, adsorbent loading, pH, and contact time on kinetics and equilibrium of adsorption of Cd²⁺ metal ion from its aqueous solution by castor seed hull (CSH) and also by activated carbon have been investigated by batch adsorption experiments. The amount of adsorption increases with initial metal ion concentration, contact time, solution pH, and the loading of adsorbent for both the systems. Kinetic experiments indicate that adsorption of cadmium metal ion on both CSH and on activated carbon consists of three steps – a rapid adsorption of cadmium metal ion, a transition phase, and an almost flat plateau region. This has also been confirmed by the intraparticle diffusion model. The lumped kinetic results show that the cadmium adsorption process follows a pseudo‐second order rate law. The kinetic parameters including the rate constant are determined at different initial metal ion concentrations, pH, amount, and type of adsorbent, respectively. The Langmuir and Freundlich adsorption isotherm models are used to describe the experimental data. The Langmuir model yields a better correlation coefficient than the other model. A comparison of the monolayer adsorption capacity (q_m) of CSH, activated carbon, and several other reported adsorbents has been provided. The value of separation factor (R_L) calculated from the Langmuir equation also gives an indication of favorable adsorption of the metal ion. From comparative studies, it has been found that CSH is a potentially attractive adsorbent than commercial activated carbon for cadmium metal ion (Cd²⁺) removal.