Estimating suspended sediment concentrations from turbidity measurements and the calibration problem

In situ turbidity meters are being increasingly used to generate continuous records of suspended sediment concentration in rivers. However, the usefulness of the information obtained depends heavily on the existence of a close relationship between fluctuations in suspended sediment concentration and turbidity and the calibration procedure that relates suspended sediment concentration to the turbidity meter's signal. This study assesses the relationship between suspended sediment concentration and turbidity for a small (1·19 km²) rural catchment in southern Brazil and evaluates two calibration methods by comparing the estimates of suspended sediment concentration obtained from the calibrated turbidity readings with direct measurements obtained using a USDH 48 suspended sediment sampler. With the first calibration method, the calibration relationship is derived by relating the turbidity readings to simultaneous measurements of concentration obtained from suspended sediment samples collected from the vicinity of the turbidity probe during flood events. With the second method, the calibration is based on the readings obtained from the turbidity meter when the probe immersed in samples of known concentration prepared using soils collected from the catchment. Overall, there was a close link between fluctuations in suspended sediment concentration and turbidity in the stream at the outlet of the catchment, and the estimates of sediment concentration obtained using the first calibration method corresponded closely with the conventionally measured sediment concentrations. However, use of the second calibration method introduced appreciable errors. When the estimated sediment concentrations were compared with the measured values, the mean errors were ± 122 mg l^?1 and + 601 mg l^?1 for the first and second calibration procedures respectively. Copyright © 2007 John Wiley & Sons, Ltd.     

Physically based modelling of sediment generation and transport under a large rainfall simulator

A series of large rainfall simulator experiments was conducted in 2002 and 2003 on a small plot located in an experimental catchment in the North Island of New Zealand. These experiments measured both runoff and sediment transport under carefully controlled conditions. A physically based hydrological modelling system (SHETRAN) was then applied to reproduce the observed hydrographs and sedigraphs. SHETRAN uses physically based equations to represent flow and sediment transport, and two erodibility coefficients to model detachment of soil particles by raindrop erosion and overland flow erosion. The rate of raindrop erosion also depended on the amount of bare ground under the simulator; this was estimated before each experiment. These erodibility coefficients were calibrated systematically for summer and winter experiments separately, and lower values were obtained for the summer experiments. Earlier studies using small rainfall simulators in the vicinity of the plot also found the soil to be less erodible in summer and autumn. Limited validation of model parameters was carried out using results from a series of autumn experiments. The modelled suspended sediment load was also sensitive to parameters controlling the generation of runoff from the rainfall simulator plot; therefore, we found that accurate runoff predictions were important for the sediment predictions, especially from the experiments where the pasture cover was good and overland flow erosion was the dominant mechanism. The rainfall simulator experiments showed that the mass of suspended sediment increased post‐grazing, and according to the model this was due to raindrop detachment. The results indicated that grazing cattle or sheep on steeply sloping hill‐country paddocks should be carefully managed, especially in winter, to limit the transport of suspended sediment into watercourses. Copyright © 2006 John Wiley & Sons, Ltd.     

The impact of slope length on the discharge of sediment by rain impact induced saltation and suspension

Simulations using a mechanistic model of raindrop driven erosion in rain‐impacted flow were performed with particles travelling by suspension, raindrop induced saltation and flow driven saltation. Results generated by both a high intensity storm, and a less intense one, indicate that, because of the effect of flow depth on the delivery of raindrop energy to the bed, there is a decline in sediment concentration, and hence soil loss per unit area, with slope length when particles are transported by raindrop induced saltation. However, that decline is reversed when the critical velocities that lead to flow driven saltation are episodically exceeded during an event. The simulations were performed on smooth surfaces and a single drop size but the general relationships are likely to apply for rain made up of a wide range of drop size. Although runoff is not always produced uniformly, as a general rule, flow velocities increase with slope length so that, typically, the distance particles travel before being discharged during an event increase with slope length. The effect of slope length on soil loss per unit area is often considered to vary with slope length to a power greater than zero and less that 1·0. The simulations show that effect of slope length on sediment discharge is highly dependent on the variations in runoff response resulting from variations in rainfall duration‐intensity‐infiltration conditions rather than plot length per se. Consequently, predicting soil loss per unit area using slope length with positive powers close to zero when sheet erosion occurs may not be as effective as commonly expected. Erosion by rain‐impacted flow is a complex process and that complexity needs to be considered when analysing the results of experiments associated with rain‐impacted flow under both natural and artificial conditions. Copyright © 2009 John Wiley & Sons, Ltd.     

The performance of grass filter strips in controlling high‐concentration suspended sediment from overland flow under rainfall/non‐rainfall conditions

There is little information on the performance of vegetative filter strips (VFS) in filtering high‐concentration sediment from subcritical overland flow. Flume experiments on simulated grass strips were conducted using combinations of three slope gradients (3°, 9° and 15°), five 1‐m‐wide slope positions (from upslope to downslope), two flow rates (60 and 20 L min^‐1 m^‐1) and sediment concentrations of 100–300 kg m^‐3 under simulated rainfall and non‐rainfall conditions. The results showed that sediment deposition efficiency increased with VFS width as a power function. Rainfall significantly reduced sediment deposited within VFS. Higher sediment concentration corresponded to a larger sediment deposition load but reduced deposition efficiency. Flow rate had a negative effect on deposition efficiency but no effect on deposition load. Sediments were more easily deposited at the upper slope position than downslope, and the upper slope position had a higher percentage of coarse sediments. The deposited sediment had significantly greater median diameters (D₅₀) than the inflow sediment. A greater proportion of coarse sediments larger than 25 µm in diameter were deposited, and particles smaller than 1 µm and of 10–25 µm had a better deposition performance than particles of 1–10 µm. Rainfall reduced the deposited sediment D₅₀ at a slope gradient of 3° and had no significant influence on it at 9° or 15°. A higher sediment concentration led to a smaller D₅₀ of the deposited sediment. Rainfall had no significant effect on overland flow velocity. Both the deposited sediment load and D₅₀ decreased with increasing flow velocity, and flow velocity was the most sensitive factor impacting sediment deposition. The results from this study should be useful to control sediment flowing into rivers in areas with serious soil erosion. Copyright © 2013 John Wiley & Sons, Ltd.     

Evaluation of a simple,inexpensive, in situ sampler for measuring time‐weighted average concentrations of suspended sediment in rivers and streams

The accurate measurement of suspended sediment (<200 μm) in aquatic environments is essential to understand and effectively manage changes to sediment, nutrient, and contaminant concentrations on both temporal and spatial scales. Commonly used sampling techniques for suspended sediment either lack the ability to accurately measure sediment concentration (e.g., passive sediment samplers) or are too expensive to deploy in sufficient number to provide landscape‐scale information (e.g., automated discrete samplers). Here, we evaluate a time‐integrated suspended sediment sampling technique, the pumped active suspended sediment (PASS) sampler, which collects a sample that can be used for the accurate measurement of time‐weighted average (TWA) suspended sediment concentration and sediment particle size distribution. The sampler was evaluated against an established passive time‐integrated suspended sediment sampling technique (i.e., Phillips sampler) and the standard discrete sampling method (i.e., manual discrete sampling). The PASS sampler collected a sample representative of TWA suspended sediment concentration and particle size distribution of a control sediment under laboratory conditions. Field application of the PASS sampler showed that it collected a representative TWA suspended sediment concentration and particle size distribution during high flow events in an urban stream. The particle size distribution of sediment collected by the PASS and Phillips samplers were comparable and the TWA suspended sediment concentration of the samples collected using the PASS and discrete sampling techniques agreed well, differing by only 4% and 6% for two different high flow events. We should note that the current configuration of the PASS sampler does not provide a flow‐weighted measurement and, therefore, is not suitable for the determination of sediment loads. The PASS sampler is a simple, inexpensive, and robust in situ sampling technique for the accurate measurement of TWA suspended sediment concentration and particle size distribution.     

Comparing grain size distribution of sediment and original soil under raindrop detachment and raindrop-induced and flow transport mechanism

The grain size distribution (GSD) of sediment in comparison with the original soil GSD is discussed under different slopes (5, 15 and 25%) and rainfall intensities (30, 60 and 90 mm h^–1 with respective duration of 30, 15 and 10 min) but identical runoff (15 mm). The sediment quantification was carried out by raindrop-induced flow transport (RIFT) or/and transport by flow (FT) using a rainfall simulator and a 6 × 1 m² erosion plot and a silt loam. The results show a high degree of enrichment for size classes of 2–4 and 4–8 μm and a high degree of depletion for size classes of >63 μm under different slopes and rainfall intensities. In addition, the results show that the experimental enrichment ratio (ER) for particle size <16 μm under different slopes and rainfall intensities was greater than 1, while the ER for particle size >32 μm was less than 1.     

An analysis of the impact of spatial variability in rainfall on runoff and sediment predictions from a distributed model

This paper investigates the effect of introducing spatially varying rainfall fields to a hydrological model simulating runoff and erosion. Pairs of model simulations were run using either spatially uniform (i.e. spatially averaged) or spatially varying rainfall fields on a 500‐m grid. The hydrological model used was a simplified version of Thales which enabled runoff generation processes to be isolated from hillslope averaging processes. Both saturation excess and infiltration excess generation mechanisms were considered, as simplifications of actual hillslope processes. A 5‐year average recurrence interval synthetic rainfall event typical of temperate climates (Melbourne, Australia) was used. The erosion model was based on the WEPP interrill equation, modified to allow nonlinear terms relating the erosion rate to rainfall or runoff‐squared. The model results were extracted at different scales to investigate whether the effects of spatially varying rainfall were scale dependent. A series of statistical metrics were developed to assess the variability due to introducing the spatially varying rainfall field. At the catchment (approximately 150 km²) scale, it was found that particularly for saturation excess runoff, model predictions of runoff were insensitive to the spatial resolution of the rainfall data. Generally, erosion processes at smaller sub‐catchment scales, particularly when the sediment generation equation had non linearity, were more sensitive to spatial rainfall variability. Introducing runon infiltration reduced the total runoff and sediment yield at all scales, and this process was also most sensitive to the rainfall resolution. Copyright © 2011 John Wiley & Sons, Ltd.     

Particle size characteristics of suspended sediment in hillslope runoff and stream flow

This study examines the particle size characteristics of hillslope soils and fluvial suspended sediments in an agricultural catchment. Samples of surface runoff and stream flow were collected periodically and analysed for the size distributions of the effective (undispersed) sediment. This sediment was subsequently dispersed and the ultimate size distributions determined. The median effective particle size of stream suspended sediment was considerably coarser than the median ultimate particle size, indicating that most of the load included a substantial proportion of aggregates. Moreover, the proportion of fine material (i.e. silt and clay) increased, and the proportion of sand-sized material decreased, with increasing discharge. This decrease in sediment size with increased flow, which is contrary to the traditional assumption of a positive discharge/particle size relationship, is thought to reflect: (i) the influx of silt and clay, predominantly the former, originating on the catchment slopes and brought to the stream by overland flow along vehicle wheelings, roads and tracks; and (ii) erosion of fine material from the channel bed and banks. During large storms, however, the proportion of sand-sized sediment increased during the rising limb of the hydrograph, as a result of the entrainment of coarser source material from the valley floor during overbank flooding. The stream suspended sediment was finer than the catchment soils and considerably finer than material eroding from the catchment slopes during storms. The degree of clay and silt enrichment in the suspended sediments was largely the result of preferential deposition of the coarser fraction during the transport and delivery of sediment from its source to basin outlet. The data from this study confirm that a significant mode of sediment transport in fluvial systems is in the form of aggregates, and that the dispersed sediment size distribution is inappropriate for determining the transportability of sediment by flow. © 1997 by John Wiley & Sons, Ltd.     

Hydroclimatic and channel snowpack controls over suspended sediment and grain size transport in a High Arctic catchment

Temporal variability in suspended sediment delivery processes was studied during three seasons in a 7·9 km² catchment at Cape Bounty, Melville Island, Nunavut in the Canadian High Arctic. Discharge was controlled primarily by the magnitude of snowmelt, with limited inputs from ground ice melt and precipitation. Years with greater snowpack non‐linearly increased sediment yield and resulted in seasonal counter‐clockwise hysteresis, while a year with low snowpack resulted in reduced sediment yield and clockwise hysteresis, and indicates that sediment was increasingly available after the onset of streamflow. In addition to the event‐scale hysteresis observed during the nival discharge peak, diurnal clockwise hysteresis was observed during all three seasons and suggests daily exhaustion of sediment supplies. These results indicate that the channel snowpack plays a primary role over sediment accessibility during the nival discharge peak. Similarly, grain size analysis of suspended material in the river showed that the coarsest mean grain size was transported during the early phase of peak nival discharge and indicates that isolated sources of coarse material were being accessed by high velocity flow. Snowpack is present through the peak nival period and conditions sediment availability by isolating channel sediments from high‐energy flow. These results indicate sediment delivery characteristics in small High Arctic catchments reflect complex interactions with channel snowpack and disproportionate responses to flow conditions that differ from glacial and temperate settings. Copyright © 2008 John Wiley & Sons, Ltd.     

Response of nephelometric turbidity to hydrodynamic particle size of fine suspended sediment

Turbidity is used as a surrogate for suspended sediment concentration (SSC), and as a regulatory tool for indicating land use disturbance and environmental protection. Turbidity relates linearly to suspended material, however, can show non-linear responses to particulate organic matter (POM), concomitant with changes in particle size distribution (PSD). In the paper the influence of ultra-fine particulate matter (UFPM) on specific turbidity and its association with POM in suspended sediment are shown for alpine rivers in the Southern Alps of New Zealand. The approach was two-fold: a field-based investigation of the relations between SSC, POM, and turbidity sampled during event flow; and experimental work on hydrodynamic particle size effects on SSC, POM, PSD, and turbidity. Specific turbidity changes over event flow and are sensitive to increasing proportional amounts of sand, UFPM, and POM in suspension. Furthermore, the UFPM is the size fraction (<6 μm) where POM increases. The implications of the current study are that the slopes of turbidity-SSC relations are undesirable in locations that may be dominated by cyclic release of POM or distinct pulses of fine-grained material. At locations where the turbidity-SSC slopes approximate 2, the POM proportion is usually <10% of the total suspended load. However, when turbidity-SSC slopes are <1 this is likely caused by high amounts of side-scatter from UFPM concomitant with higher proportions of POM. Thus, the use of turbidity as a proxy for determining SSC may have serious consequences for the measurement of representative suspended sediment data, particularly in locations where POM may be a significant contributor to overall suspended load.     

Application of piezoelectric transducers in simulated rainfall erosivity assessment

Abstract

Rainfall simulators have often been used to mimic natural rainfall for studies of various land-surface and water interaction processes. The characteristics of the simulated rainfall are the main indicators used to judge the performance of the rainfall simulators. The aim of this study is to investigate the potential of piezoelectric transducers for measuring and evaluating a dripper-type simulated rainfall drop-size distribution (DSD) and kinetic energy (KE). The directly measured KE was significantly correlated with the estimated KE using the drop-size distribution and empirical rain drop fall velocity relationships. This result emphasizes the potential use of the piezoelectric sensor to directly measure and evaluate rainfall kinetic energy. Also, the relationship between rainfall intensity and KE showed good patterns of agreement between simulated rainfall and natural rainfall.

Citation Abd Elbasit, M. A. M., Yasuda, H. & Salmi, A. (2011) Application of piezoelectric transducers in simulated rainfall erosivity assessment. Hydrol. Sci. J. 56(1), 187–194.     

Effect of shrub-grass vegetation coverage and slope gradient on runoff and sediment yield under simulated rainfall

Evaluating the benefits of sediment and runoff reduction in different vegetation types is essential for studying the mechanisms of soil and water conservation on the Loess Plateau.The experiment was conducted in shrub-grass plots with nine levels of mixed vegetation coverage from 0%to 70%,three slopes(10
,15
,and 20
)and two rainfall intensities(1.0 and 2.5 mm/min).The results showed that the vegetation coverage and slope gradient significantly affect runoff and sediment yield.Shrub-grass vegetation coverage had a significant effect on the runoff start-time,runoff flow velocity,runoff rate,and soil erosion rate on hillslopes.Mixed vegetation coverage could effectively delay the runoff starttime and decrease the runoff flow velocity.However,the effects of the slope gradient on runoff and sediment yield are opposite to those of vegetation coverage.Shrub-grass vegetation coverage could effectively increase runoff and sediment yield reduction benefits,while their benefits were affected by the rainfall intensity.At the 1.0 mm/min rainfall intensity,the reduction in the sediment production rate was greater than that under the 2.5 mm/min intensity.However,when the shrub-grass vegetation coverage exceeded 42%,the runoff reduction benefit was more obvious at higher rainfall intensities.The cumulative sediment yield increased with increasing cumulative runoff,and the rate of increase in the cumulative runoff was greater than that of the cumulative sediment yield with increasing of shrub-grass vegetation coverage.Moreover,there was a power function relationship between cumulative sediment yield and cumulative runoff yield(P<0.05).Our paper is expected to provide a good reference on the ecological environment and vegetation construction on the Loess Plateau.     

Application of an optical disdrometer to characterize simulated rainfall and measure drop-size distribution

ABSTRACT

Knowledge of rainfall characteristics such as drop-size distribution is essential for the development of erosion-mitigation strategies and models. This research used an optical disdrometer to elucidate the relationships between raindrop-size distribution, median volume drop diameter (D₅₀), kinetic energy and radar reflectivity (dBz) of simulated rainfall of different intensities. The D₅₀ values were higher for the simulated rain than for natural rain at almost all rainfall intensities, perhaps due to variations in rainfall types and the turbulence in natural rain that breaks up large drops. The kinetic energy ranged from 26.67 to 5955.51 J m^?2 h ^?1, while the median volume drop diameter (D₅₀) was in the range 1.94–7.25 mm, for intensities between 1.5 and 202.6 mm h^?1. The relationship between radar reflectivity (Z) and the intensity (R) of the simulated rain was best described by a power law function (Z = aR^b), with a and b coefficients in the ranges 162–706 and 0.94–2.46, respectively, throughout the range of rainfall intensities (1.5–202.6 mm h^?1).     

Application of soft-computing techniques in forecasting sediment load and concentration

ABSTRACT

This paper investigates conventional and soft-computing methods for the estimation of suspended sediment concentration (SSC) and load (SSL) in rivers. Frequently used methods of sediment rate curve (SRC) and multi-nonlinear regression, and soft-computing methods of multi-layer perceptron, multi-linear regression and adaptive neuro-fuzzy inference system are implemented using various hydrological and hydraulic parameters for the Little Kickapoo Creek Watershed, Illinois, USA. All methods performed equally well in the estimation of SSL, without any noticeable outperformance from any from the methods. However, the application of soft-computing methods decreased SSC estimation errors considerably as compared to the results of SRC. The results are significant in the way they reconcile traditionally used hydrological parameters into the soft-computing methods. Overall, soft-computing methods are recommended for the estimation of SSC in rivers because of their reasonably better performance and ease of implementation.     

Time‐integrated sampling of fluvial suspended sediment: a simple methodology for small catchments

Fine‐grained (<62·5 µm) suspended sediment transport is a key component of the geochemical flux in most fluvial systems. The highly episodic nature of suspended sediment transport imposes a significant constraint on the design of sampling strategies aimed at characterizing the biogeochemical properties of such sediment. A simple sediment sampler, utilizing ambient flow to induce sedimentation by settling, is described. The sampler can be deployed unattended in small streams to collect time‐integrated suspended sediment samples. In laboratory tests involving chemically dispersed sediment, the sampler collected a maximum of 71% of the input sample mass. However, under natural conditions, the existence of composite particles or flocs can be expected to increase significantly the trapping efficiency. Field trials confirmed that the particle size composition and total carbon content of the sediment collected by the sampler were representative statistically of the ambient suspended sediment. Copyright © 2000 John Wiley & Sons, Ltd.     

Intra‐event intermittency of rainfall: an analysis of the metrics of rain and no‐rain periods

The metric or ‘observable’ properties of intra‐event rainfall intermittency (IERI) are quantified using a 10‐year record from arid Fowlers Gap, Australia. Rainfall events were delineated using the minimum inter‐event time (MIT) criterion, using eight values in the range of 1 h – 24 h. Within events, no‐rain periods were defined as corresponding to rainfall rates R < 0.1 mm/h or R < 0.2 mm/h (both less than typical wet‐canopy evaporation rates during rainfall). In this way, rainfall events were subdivided into rain and no‐rain periods. Intermittency was characterised using two measures: the fraction of rainless time within an event, and the duration of the longest rainless period. Events identified using a minimum inter‐event time (MIT) of 24 h included on average 9.4 h of contiguous no‐rain time (47.5% of the mean event duration), and only 6.8 h of contiguous rain. Total IERI averaged 51.1% for these events. Events defined with MIT = 6 h (a value commonly adopted in the literature) exhibited a mean of 1.53 h of no‐rain and 9.04 h of contiguous rain. Total IERI averaged 13.9% for these events for R < 0.1 mm/h, but reached 39.2% if no‐rain periods were taken as those of <0.2 mm/h. The maximum contiguous no‐rain period for events defined using MIT = 6 h was 10.9 h from an event of 12.6 h duration, and this represents 86.5% of the event duration. Results demonstrate that smaller, shorter, and less intense rainfall events tend to exhibit higher IERI than larger, longer, and more intense events. IERI is relevant to the understanding of land surface processes. Information on the metric properties of IERI in different rainfall types (convective and stratiform) and rainfall climates (arid, maritime, and wet tropical) may prove to have significance for diverse studies in land surface hydrology. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of the undecomposed layer and semi-decomposed layer of Quercus variabilis litter on the soil erosion process and the eroded sediment particle size distribution

Simulated rainfall experiments were performed on bare, undecomposed litter layer and semi-decomposed litter layer slopes with litter biomasses of 0, 50, 100 and 150 g m⁻², respectively, to evaluate the effect of the undecomposed layer and semi-decomposed layer of Quercus variabilis litter on the soil erosion process and the particle size distribution of eroded sediment. The undecomposed layer and semi-decomposed layer of litter reduced the runoff rate by 10.91–27.04% and 12.91–36.05%, respectively, and the erosion rate by 13.35–40.98% and 17.16–59.46%, respectively. The percentage of smaller particles (clay and fine silt particles) decreased and the percentage of larger particles (coarse silt and sand particles) increased with an increased rainfall duration on all treated slopes, while the extent of the eroded sediment particle content varied among the treated slopes with the rainfall duration, with bare slopes exhibiting the largest variability, followed by undecomposed litter layer slopes and finally semi-decomposed litter layer slopes. The clay and sand particles were transported as aggregates, and fine silt and coarse silt particles were transported as primary particles. Compared with the original soil, sediment eroded from all treated slopes was mainly enriched in smaller particles. Furthermore, the loss of the smaller particles from the undecomposed litter layer slopes was lower than that from the semi-decomposed litter layer slopes, indicating that the undecomposed litter layer alleviated soil coarsening to some extent. The findings from this study improve our understanding of how litter regulates slope erosion and provide a reference for effectively controlling soil erosion.     

Real-time prediction of the peak suspended sediment concentration and sediment yield of the Lao-Nung River during storms

Based on rainfall erosion of soil and suspended sediment transport in storm events, a method is proposed to predict peak suspended sediment concentration and suspended sediment yield in watersheds based on rainfall characteristics prior to peak rainfall intensity. The rainfall characteristics factors that dominate peak suspended sediment concentration C_p are rainfall erosion factor R_ef, first peak rainfall intensity of area-average rainfall i_p1 and antecedent precipitation index I_ap; the rainfall characteristics factors that dominate suspended sediment yield Y_ss in storm events are total rainfall P, suspended sediment yield factor R_sf and antecedent precipitation index I_ap. This research focuses on watersheds in Liau-Kwei observation station along Lao-Nung River in southern Taiwan as the research object, and adopts the PSED-model to simulate the discharge hydrograph, suspended sediment concentration hydrograph and suspended sediment yield in 11 storm events for analysis. The analytical results show that there is a good correlation between the above-mentioned rainfall characteristics factors and C_p as well as Y_ss, thus enabling C_p and Y_ss to be predicted by using Expressions (13) and (14). These two expressions are utilized to predict C_p and Y_ss of Typhoon Morakot in 2009, and the results are compared with those from simulation by using the PSED-model. The result of comparison shows there is a good capability in predicting. For the watersheds where it is necessary to predict C_p and Y_ss of a storm event for the benefit of effective operation of water resource facilities, the aforesaid rainfall characteristics factors can be utilized to establish applicable models for prediction.     

Relationship between bed shear stress and suspended sediment concentration:annular flume experiments

In this study,annular flume experiments were carried out,using the sediment samples collected from the lower part of the inter-tidal zone at Xiaoyangkou,Jiangsu coast,China.The Ariathurai-Partheniades equation was used to determine the bed shear stress,by evaluating variations in the suspended sediment concentration within the water column.The derived relation between the bed shear stress and suspended sediment concentration shows that,at various stages of seabed erosion, suspended sediment concentration increases rapidly when the flow velocity is increased,but the pattern of change in the bed shear stress does not follow suit.At low concentrations,bed shear stress initially increases markedly with increasing flow velocity.However,when the concentration reaches an apparently critical level around 0.55 kg m"3,the rate of change in the bed shear stress abruptly slows down,or becomes almost constant,in response to further increases in the flow velocity.Results of experiments indicate that,from a critical level onward,suspended sediment concentration has a strong influence on the bed shear stress.     

Lithological controls on hillslope sediment supply: insights from landslide activity and grain size distributions

The volumes, rates and grain size distributions of sediment supplied from hillslopes represent the initial input of sediment delivered from upland areas and propagated through sediment routing systems. Moreover, hillslope sediment supply has a significant impact on landscape response time to tectonic and climatic perturbations. However, there are very few detailed field studies characterizing hillslope sediment supply as a function of lithology and delivery process. Here, we present new empirical data from tectonically‐active areas in southern Italy that quantifies how lithology and rock strength control the landslide fluxes and grain size distributions supplied from hillslopes. Landslides are the major source of hillslope sediment supply in this area, and our inventory of ~2800 landslides reveals that landslide sediment flux is dominated by small, shallow landslides. We find that lithology and rock strength modulate the abundance of steep slopes and landslides, and the distribution of landslide sizes. Outcrop‐scale rock strength also controls the grain sizes supplied by bedrock weathering, and influences the degree of coarsening of landslide supply with respect to weathering supply. Finally, we show that hillslope sediment supply largely determines the grain sizes of fluvial export, from catchments and that catchments with greater long‐term landslide rates deliver coarser material. Therefore, our results demonstrate a dual control of lithology on hillslope sediment supply, by modulating both the sediment fluxes from landslides and the grain sizes supplied by hillslopes to the fluvial system. Copyright © 2017 John Wiley & Sons, Ltd.