Sand detachment by wind‐driven raindrops

Wind movement and velocity can have a profound effect on some aspects of the soil erosion process. In the case of wind‐driven rain, differences in raindrop trajectory are expected: wind‐driven raindrops achieve some degree of horizontal velocity, which increases their resultant impact velocity and they strike the soil surface at an angle deviated from the vertical under the effects of both gravitational and drag forces. However, not much is known about the physical impact of raindrops on a soil in situations where this impact is at an angle, and it is also not precise known if oblique raindrops have stronger erosive effects than vertical ones. A series of tests was conducted to assess the effect of wind velocities on sand detachment from splash cups in a wind tunnel facility equipped with a rainfall simulator. Splash cups packed with standard sand were exposed to windless rains and to rains driven by horizontal wind velocities of 6, 10 and 14 m s^?1 to evaluate the sand detachment by wind‐driven raindrops. The average angle of rain inclination from vertical was calculated from the direct intensity measurements implemented with windward and leeward‐facing raingauges placed at different slopes. A kinetic energy sensor measured energy of windless and wind‐driven rains. Results showed that the kinetic energy flux calculated by the resultant impact velocity of drops adequately described the sand detachment from the splash cups by wind‐driven raindrops. However, an additional analysis of Pearson correlation coefficients using the velocity components rather than the resultant velocity of wind‐driven raindrops indicated that the energy flux related to the horizontal component of wind‐driven raindrops had a greater correlation with sand detachment than that related to the normal component. This finding contradicted the general assumption that the component of velocity normal to the surface is related to the detachment. Copyright © 2005 John Wiley & Sons, Ltd.     

Wind effects on sediment transport by raindrop‐impacted shallow flow: a wind‐tunnel study

In wind‐driven rains, wind velocity and direction are expected to affect not only energy input of rains but also shallow ?ow hydraulics by changing roughness induced by raindrop impacts with an angle on ?ow and the unidirectional splashes in the wind direction. A wind‐tunnel study under wind‐driven rains was conducted to determine the effects of horizontal wind velocity and direction on sediment transport by the raindrop‐impacted shallow ?ow. Windless rains and the rains driven by horizontal wind velocities of 6 m s^?1, 10 m s^?1, and 14 m s^?1 were applied to three agricultural soils packed into a 20 by 55 cm soil pan placed on both windward and leeward slopes of 7 per cent, 15 per cent, and 20 per cent. During each rainfall application, sediment and runoff samples were collected at 5‐min intervals at the bottom edge of the soil pan with wide‐mouth bottles and were determined gravimetrically. Based on the interrill erosion mechanics, kinetic energy ?ux (E_rn) as a rainfall parameter and product of unit discharge and slope in the form of q^bS^c_o as a ?ow parameter were used to explain the interactions between impact and ?ow parameters and sediment transport (q_s). The differential sediment transport rates occurred depending on the variation in raindrop trajectory and rain intensity with the wind velocity and direction. Flux of rain energy computed by combining the effects of wind on the velocity, frequency, and angle of raindrop impact reasonably explained the characteristics of wind‐driven rains and acceptably accounted for the differences in sediment delivery rates to the shallow ?ow transport (R₂ ≥ 0·78). Further analysis of the Pearson correlation coef?cients between E_rn and qS_o and q_s also showed that wind velocity and direction signi?cantly affected the hydraulics of the shallow ?ow. E_rn had a smaller correlation coef?cient with the q_s in windward slopes where not only reverse splashes but also reverse lateral raindrop stress with respect to the shallow ?ow direction occurred. However, E_rn was as much effective as qS_o in the sediment transport in the leeward slopes where advance splashes and advance lateral raindrop stress on the ?ow occurred. Copyright © 2004 John Wiley & Sons, Ltd.     

Impact of wind on the spatial distribution of rain over micro‐scale topography: numerical modelling and experimental verification

The wind‐driven‐rain effect refers to the redistribution of rainfall over micro‐scale topography due to the existence of local perturbed wind‐flow patterns. Rainfall measurements reported in the literature point to the fact that the wind‐driven‐rain distribution can show large variations over micro‐scale topography. These variations should be taken into account in hillslope hydrology, in runoff and erosion studies and in the design of rainfall monitoring networks. In practice, measurements are often not suitable for determining the wind‐driven‐rain distribution. Therefore, a few researchers have employed numerical modelling. In order to provide confidence in using numerical models, experimental verification for a range of different topographic features is imperative. The objective of this study is to investigate the adequacy of a two‐dimensional Computational Fluid Dynamics (CFD) model to predict the wind‐driven‐rain distribution over small‐scale topography. The numerical model is applied to a number of topographic features, including a succession of cliffs, a small isolated hill, a small valley and a field with ridges and furrows. The numerical results are compared with the corresponding measurement results reported in the literature. It is shown that two‐dimensional numerical modelling can provide a good indication of the wind‐driven‐rain distribution over each type of micro‐scale topography that is considered in this study. It is concluded that more detailed verification procedures are currently inhibited due to the lack of available and detailed spatial and temporal rainfall data from field measurements. Copyright © 2005 John Wiley & Sons, Ltd.     

Backshore coarsening processes triggered by wave‐induced sand transport: the critical role of storm events

Spatial backshore processes were investigated through field observations of topography and median sand grain size at a sandy beach facing the Pacific Ocean in Japan. A comparison of the backshore profile and cross‐shore distribution of the median sand grain size in 1999 and 2004 revealed an unusual sedimentary process in which sand was coarsened in a depositional area in the 5‐year period, although sediment is generally coarsened in erosional areas. In support of these observations, monthly spatial field analyses carried out in 2004 demonstrated a remarkable backshore coarsening process triggered by sedimentation in the seaward part of the backshore during a storm event. In order to elucidate mechanisms involved in the backshore coarsening process, thresholds of movable sand grain size under wave and wind actions (a uniform parameter for both these cases) in the onshore and offshore directions were estimated using wave, tide, and wind data. The cross‐shore distributions of the estimated thresholds provided reasonable values and demonstrated a coarsening mechanism involving the intermediate zone around the shoreline under alternating wave and wind actions as a result of which coarse sand was transported toward the seaward part of the backshore by large waves during storms and then toward the landward part by strong onshore winds. The 5‐year backshore coarsening is most certainly explained by repetition of short‐term coarsening mechanisms caused by wave‐induced sand transport occurring from the nearshore to the intermediate zone. Copyright © 2010 John Wiley & Sons, Ltd     

Using a pore‐scale model to quantify the effect of particle re‐arrangement on pore structure and hydraulic properties

A pore‐scale model based on measured particle size distributions has been used to quantify the changes in pore space geometry of packed soil columns resulting from a dilution in electrolyte concentration from 500 to 1 mmol l^?1 NaCl during leaching. This was applied to examine the effects of particle release and re‐deposition on pore structure and hydraulic properties. Two different soils, an agricultural soil and a mining residue, were investigated with respect to the change in hydraulic properties. The mining residue was much more affected by this process with the water saturated hydraulic conductivity decreasing to 0·4% of the initial value and the air‐entry value changing from 20 to 50 cm. For agricultural soil, there was little detectable shift in the water retention curve but the saturated hydraulic conductivity decreased to 8·5% of the initial value. This was attributed to localized pore clogging (similar to a surface seal) affecting hydraulic conductivity, but not the microscopically measured pore‐size distribution or water retention. We modelled the soil structure at the pore scale to explain the different responses of the two soils to the experimental conditions. The size of the pores was determined as a function of deposited clay particles. The modal pore size of the agricultural soil as indicated by the constant water retention curve was 45 µm and was not affected by the leaching process. In the case of the mining residue, the mode changed from 75 to 45 µm. This reduction of pore size corresponds to an increase of capillary forces that is related to the measured shift of the water retention curve. Copyright © 2007 John Wiley & Sons, Ltd.     

Formative conditions and sedimentary structures of sandy 3D antidunes: an application of the gravel step‐pool model to fine‐grained sand in an experimental flume

Antidunes and their sedimentary structures can be useful in reconstructing paleo‐hydraulic conditions, especially for large discharge events. However, three‐dimensional (3D) antidunes in sand‐sized sediments have not yet been studied extensively, as compared to either two‐dimensional (2D) antidunes or antidunes in gravel‐sized sediments. In this study, we estimated formative conditions of gravel step‐pool morphologies and applied them to the formation of 3D antidunes over a sand bed. Formative conditions are expressed in terms of a relationship between the water discharge per unit width and the bed slope. Flume experiments demonstrated that 3D mound‐like antidune configurations and their associated internal sedimentary structures could be preserved. Internal sedimentary structures were characterized by shallow lens‐like structures whose bases were erosional. Although gently‐dipping concave‐upward lamination was dominant, convex‐upward lamination was occasionally observed. The dimensions of lenticular lamina‐sets can be used to estimate antidune geometry. Thus if 3D antidunes can be interpreted in the stratigraphic record, it is possible to estimate the paleo‐hydraulic parameters such as water discharge and bed slope more precisely than previously. Copyright © 2010 John Wiley & Sons, Ltd.     

‘Thailand was a desert' during the mid‐Cretaceous: Equatorward shift of the subtropical high‐pressure belt indicated by eolian deposits (Phu Thok Formation) in the Khorat Basin,northeastern Thailand

The Tibetan Plateau is a key factor in controlling the present‐day climate and atmospheric circulation pattern in Asia. The pattern of atmospheric circulation after the uplift of the plateau is well known, whereas direct evidence is lacking regarding the nature of the circulation pattern prior to the uplift. The distribution of desert directly reflects the position of the subtropical high‐pressure belt, and the prevailing surface‐wind pattern recorded in desert deposits reveals the position of its divergence axis. Cretaceous eolian sandstone of the Phu Thok Formation is extensively exposed in the northern Khorat Basin, northeastern Thailand. We conducted a sedimentological study on this formation to reconstruct temporal changes in the latitude of the subtropical high‐pressure belt in low‐latitude Asia during the Cretaceous. Spatio‐temporal changes in the paleo‐wind directions recorded in the Phu Thok Formation reveal that the Khorat Basin mainly belonged to the northeast trade wind belt and subtropical high‐pressure belt was situated to the north of the Khorat Basin during the initial stages of deposition, shifted southward to immediately above the basin during the main phase of deposition, and then shifted northward again to the north of the basin during the final stages of deposition. The paleomagnetic polarity sequence obtained for the Phu Thok Formation comprises three zones of normal polarity and two of reversed polarity, correlating to chrons M1n to C34n of the geomagnetic polarity time scale. This result suggests that the Phu Thok Formation is mid‐Cretaceous in age (from c. 126 Ma to c. 99–93 Ma), similar to the age of eolian sandstone in the Sichuan Basin, southern China (the Jiaguan Formation). These results, in combination with paleo‐wind direction data, suggest the development of low‐latitude desert and an equatorward shift of the subtropical high‐pressure belt (relative to the present‐day) in Asia during the mid‐Cretaceous.     

Coupling of a Column System with ICP‐MS for the Characterisation of Colloid‐mediated Metal(loid) Transport in Porous Media

In this work a coupling method for the characterisation of colloid‐mediated transport of the metal(loid) species in porous media was developed. For this transport experiments quartz sand was used as column packing material and the synthetic three‐layer clay mineral laponite as model colloid. The determination of colloids was conducted by means of UV detection. The quantification of the metal(loid) ions was carried out in two different ways: (1) The fractions collected at the column outlet were analysed with an inductively coupled plasma mass spectrometer (ICP‐MS) (offline measurements); (2) the column system was directly coupled with ICP‐MS (online measurements). In the column experiments the influence of laponite colloids on the transport of Cu, Pb, Zn, Pt and As species was investigated. In the offline experiments as a consequence of dilution during sample preparation no metal(loid) species at the column outlet could be found. Unlike this the breakthrough of all metal(loid)s could be detected under the same experimental column conditions in the coupling experiments. This coupling technique offers the online detection of the metal species and colloidal particles with high resolution even at low concentrations and without any time‐consuming preparation. The coupling experiments have shown that the laponite particles accelerate the transport of the cationic metals. For anionic metal(loid) species no influence of laponite on their transport behaviour was found.     

Flow separation at the inner (convex) and outer (concave) banks of constant‐width and widening open‐channel bends

There is a paucity of data and insight in the mechanisms of, and controls on flow separation and recirculation at natural sharply‐curved river bends. Herein we report on successful laboratory experiments that elucidate flow structure in one constant‐width bend and a second bend with an outer‐bank widening. The experiments were performed with both a flat immobile gravel bed and mobile sand bed with dominant bedload sediment transport. In the constant‐width bend with immobile bed, a zone of mainly horizontal flow separation (vertical rotational axis) formed at the inner bank that did not contain detectable flow recirculation, and an outer‐bank cell of secondary flow with streamwise oriented rotational axis. Surprisingly, the bend with widening at the outer bank and immobile bed did not lead to a transverse expansion of the flow. Rather, flow in the outer‐bank widening weakly recirculated around a vertical axis and hardly interacted with the inner part of the bend, which behaved as a constant‐width bend. In the mobile bed experiment, downstream of the bend apex a pronounced depositional bar developed at the inside of the bend and pronounced scour occurred at the outside. Moreover the deformed bed promoted flow separation over the bar, including return currents. In the constant‐width bend, the topographic steering impeded the generation of an outer‐bank cell of secondary flow. In the bend with outer‐bank widening, the topographic steering induced an outward expansion of the flow, whereby the major part of the discharge was conveyed in the central part of the widening section. Flow in the outer‐bank widening was highly three dimensional and included return currents near the bottom. In conclusion, the experiments elucidated three distinct processes of flow separation common in sharp bends: flow separation at the inner bank, an outer‐bank cell of secondary flow, and flow separation and recirculation in an outer‐bank widening. Copyright © 2012 John Wiley & Sons, Ltd.     

The use of small‐format and low‐altitude aerial photos for the realization of high‐resolution DEMs in mountainous areas: application to the Super‐Sauze earthflow (Alpes‐de‐Haute‐Provence,France)

Geomorphologists have to make choices and compromises, as acquisition techniques of geometrical information are numerous, depending on the specific complexity of the targeted three‐dimensional objects and the requirements of the end user. This article presents the methodology and the results over a well known and documented site. This ready‐to‐use, low‐altitude, aerial photo methodology reveals itself to be a satisfying compromise between cost, accuracy and difficulty of implementation. The selected equipment package is light enough to enable a quick reaction to unexpected events and the tools and methods are competitive with field acquisition techniques. An evaluation has demonstrated a sub‐metric accuracy for the final result. Copyright © 2002 John Wiley & Sons, Ltd.     

Near‐fault ground motions,and the response of elastic and inelastic single‐degree‐of‐freedom (SDOF) systems

In order to investigate the response of structures to near‐fault seismic excitations, the ground motion input should be properly characterized and parameterized in terms of simple, yet accurate and reliable, mathematical models whose input parameters have a clear physical interpretation and scale, to the extent possible, with earthquake magnitude. Such a mathematical model for the representation of the coherent (long‐period) ground motion components has been proposed by the authors in a previous study and is being exploited in this article for the investigation of the elastic and inelastic response of the single‐degree‐of‐freedom (SDOF) system to near‐fault seismic excitations. A parametric analysis of the dynamic response of the SDOF system as a function of the input parameters of the mathematical model is performed to gain insight regarding the near‐fault ground motion characteristics that significantly affect the elastic and inelastic structural performance. A parameter of the mathematical representation of near‐fault motions, referred to as ‘pulse duration’ (T_P), emerges as a key parameter of the problem under investigation. Specifically, T_P is employed to normalize the elastic and inelastic response spectra of actual near‐fault strong ground motion records. Such normalization makes feasible the specification of design spectra and reduction factors appropriate for near‐fault ground motions. The ‘pulse duration’ (T_P) is related to an important parameter of the rupture process referred to as ‘rise time’ (τ) which is controlled by the dimension of the sub‐events that compose the mainshock. Copyright © 2004 John Wiley & Sons, Ltd.     

Using meteorological observer data to compare wind erosion during two great droughts in eastern Australia; the World War II Drought (1937–1946) and the Millennium Drought (2001–2010)

Australian meteorological observers started using the World Meteorological Organization (WMO) weather coding system in the 1950s. This system is still in use around the world today. However, observing and recording the weather in an organized and systematic manner had been ongoing for over 100 years prior to the adoption of this coding system, and much like Australia, most countries will have historical meteorological records. In this paper we compare the wind erosion of two of the greatest droughts in Australian recorded history; the World War II (WWII) Drought (1937–1945) and the Millennium Drought (2001–2009). To do this we analysed previously unavailable meteorological observer records from the Australian Bureau of Meteorology (ABM). Wind erosion records, mostly in long‐hand written form, were translated to the modern WMO coding system for the WWII Drought and compared with the wind erosion of Australia's recently‐ended Millennium Drought, one of the longest and harshest on record. We quantify wind erosion using Dust Event Days (DED) and a modified version of a published Dust Storm Index (DSI) to show that wind erosion during the WWII Drought was up to 4.6 times higher than during the Millennium Drought. This study has international significance because it demonstrates a methodology for tracking changes in wind erosion over the past 75 years based on observer records available in every country with a history of organized weather observation. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Poly(2‐hydroxyethylmethacrylate‐hydroxyapatite) a Novel Composite for the Removal of Lead(II) from Aqueous Solutions

In the present study, a novel adsorbent, poly (2‐hydroxyethylmethacrylate‐hydroxyapatite) [P(HEMA‐Hap)], was prepared and characterized. The synthesis was achieved by means of free‐radical polymerization and a number of structural characterization methods, including FT‐IR, XRD, TGA, SEM, BET‐porosity, and swelling tests. Pb²⁺ adsorption was performed using a series of pH, time, and temperature ranges. The reusability of the composite was also tested. The results obtained indicated that the novel adsorbent is able to bind Pb²⁺ ions with strong chemical affinity. The adsorption results were fitted to the classic Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) sorption models. Thermodynamic parameters obtained demonstrated that the sorption process was spontaneous (ΔG < 0), endothermic (ΔH > 0), as expected. The process was also consistent with the pseudo‐second‐order model, and chemical adsorption was determined to be the rate‐controlling step. It was also shown that the composite could be used for five consecutive adsorption processes.     

Confidence interval of real‐time forecast stages provided by the STAFOM‐RCM model: the case study of the Tiber River (Italy)

This study proposes a statistically based procedure to quantify the confidence interval (CI) to be associated to the stages forecast by a simple model called STAge FOrecasting Model‐Rating Curve Model (STAFOM‐RCM). This model can be used for single river reaches characterized by different intermediate drainage areas and mean wave travel times when real‐time stage records, cross section surveys and rating curves are available at both ends. The model requires, at each time of forecast, an estimate of the lateral contribution q_for between the two sections delimiting the reach. The CI of the stage is provided by analyzing the statistical properties of model output in terms of lateral flow, and it is derived from the CI of the lateral contribution q_for which, in turn, is set up by associating to each q_for the q_opt which allows STAFOM‐RCM to reproduce the exact observed stage. From an operative point of view, the q_for values are ranked in order of magnitude and subdivided in classes where the q_opt values can be represented through normal distributions of proper mean and variance from which an interval of selected confidence level for q_for is computed and transferred to the stage. Three river reaches of the Tiber river, in central Italy, are used as case study. A sensitivity analysis is also performed in order to identify the minimum calibration set of flood events. The CIs obtained are consistent with the level of confidence selected and have practical utility. An interesting aspect is that different CI widths can be produced for the same forecast stage since they depend on the estimate of q_for made at the time of forecast. Overall, the proposed procedure for CI estimate is simple and can be conveniently adapted for other forecasting models provided that they have physically based parameters which need to be updated during the forecast. Copyright © 2012 John Wiley & Sons, Ltd.     

Dredge petrology of the boninite‐ and adakite‐bearing Hahajima Seamount of the Ogasawara (Bonin) forearc: An ophiolite or a serpentinite seamount?§

Abstract During the Hakuho‐Maru KH03‐3 cruise and the Tansei‐Maru KT04‐28 cruise, more than 1000 rock samples were dredged from several localities over the Hahajima Seamount, a northwest–southeast elongated, rectangular massif, 60 km × 30 km in size, with a flat top approximately 1100 m deep. The rocks included almost every lithology commonly observed among the on‐land ophiolite outcrops. Volcanic rocks included mid‐oceanic ridge basalt (MORB)‐like tholeiitic basalt and dolerite, calc‐alkaline basalt and andesite, boninite, high‐Mg adakitic andesite, dacite, and minor rhyolite. Gabbroic rocks included troctolite, olivine gabbro, olivine gabbronorite (with inverted pigeonite), gabbro, gabbronorite, norite, and hornblende gabbro, and showed both MORB‐type and island arc‐type mineralogies. Ultramafic rocks were mainly depleted mantle harzburgite (spinel Cr? 50–80) and its serpentinized varieties, with some cumulate dunite, wehrlite and pyroxenites. This rock assemblage suggests a supra‐subduction zone origin for the Hahajima Seamount. Compilation of the available dredge data indicated that the ultramafic rocks occur in the two northeast–southwest‐oriented belts on the seamount, where serpentinite breccia and gabbro breccia have also developed, but the other areas are free from ultramafic rocks. Although many conical serpentinite seamounts 10 km in size are aligned along the Izu–Ogasawara (Bonin)–Mariana forearc, the Hahajima Seamount may be better interpreted as a fault‐bounded, uplifted massif composed of ophiolitic thrust sheets, resembling the Izki block of the Oman ophiolite in its shape and size. The ubiquitous roundness of the dredged rocks and their thin Mn coating (<2 mm) suggest that the Hahajima Seamount was uplifted above sealevel and wave‐eroded, like the present Macquarie Is., a rare example of ophiolite exposure in an oceanic setting. The Ogasawara Plateau on the Pacific Plate is adjacent to the east of the Hahajima Seamount, and collision and subduction of the plateau may have caused uplift of the forearc ophiolite body.     

Applying multifractality and the self‐organized criticality theory to describe the temporal rainfall regimes in Andalusia (southern Spain)

A multifractal analysis of hourly and daily rainfall data recorded at four locations of Andalusia (southern Spain) was carried out in order to study the temporal structure of rainfall and to find differences between both time resolutions. The results show that an algebraic tail is required to fit the probability distribution of the extreme rain events for all the cases. The presence of a multifractal phase transition associated with a critical moment in the empirical moments scaling exponent function was also detected. Both facts indicate that the rainfall process is a case of self‐organized criticality (SOC) dynamics, although the results differ for each place according to the time resolution and the nature of the rainfall, either convective or frontal. This SOC behaviour is related to a statistically steady state that implies the presence of clusterization in the time‐occurrence sequence of rain events. Such fluctuations have been shown by performing the analysis of the Fano and Allan factors and the count‐based periodogram. The values for the “synoptic maximum”, the typical lifetime of planetary scale atmospheric structures, have been obtained for each place and some important periodicities have been detected when dealing with extremes. Copyright © 2007 John Wiley & Sons, Ltd.     

Quantifying the rate and depth dependence of bioturbation based on optically‐stimulated luminescence (OSL) dates and meteoric 10Be

Both the rate and the vertical distribution of soil disturbance modify soil properties such as porosity, particle size, chemical composition and age structure; all of which play an important role in a soil's biogeochemical functioning. Whereas rates of mixing have been previously quantified, the nature of bioturbation's depth dependence remains poorly constrained. Here we constrain, for the first time, the relationship between mixing rate and depth in a bioturbated soil in northeast Queensland, Australia using a novel method combining OSL (optically‐stimulated luminescence) ages and meteoric beryllium‐10 (¹⁰Be) inventories. We find that the best fit mixing rate decreases non‐linearly with increasing soil depth in this soil and the characteristic length scale of 0.28 m over which the mixing coefficient decays is comparable to reported rooting depth coefficients. In addition we show that estimates of surface mixing rates from OSL data are highly dependent on erosion rate and that erosion rate must be constrained if accurate mixing rates are to be quantified. We calculate surface diffusion‐like mixing coefficients of 1.8 × 10^?4 and 2.1 × 10^?4 m² yr^?1 for the studied soil for two different estimates of soil erosion. © 2014 The Authors. Earth Surface Processes and Landforms Published by John Wiley & Sons Ltd.     

Normal fault growth and linkage in the Gediz (Alaşehir) Graben,Western Turkey,revealed by transient river long‐profiles and slope‐break knickpoints

The Gediz (Ala?ehir) Graben is located in the highly tectonically active and seismogenic region of Western Turkey. The rivers upstream of the normal fault‐bounded graben each contain a non‐lithologic knickpoint, including those that drain through inferred fault segment boundaries. Knickpoint heights measured vertically from the fault scale with footwall relief and documented fault throw (vertical displacement). Consequently, we deduce these knickpoints were initiated by an increase in slip rate on the basin‐bounding fault, driven by linkage of the three main fault segments of the high‐angle graben bounding fault array. Fault interaction theory and ratios of channel steepness suggest that the slip rate enhancement factor on linkage was a factor of 3. We combine this information with geomorphic and structural constraints to estimate that linkage took place between 0.6 Ma and 1 Ma. Calculated pre‐ and post‐linkage throw rates are 0.6 and 2 mm/yr respectively. Maximum knickpoint retreat rates upstream of the faults range from 4.5 to 28 mm/yr, faster than for similar catchments upstream of normal faults in the Central Apennines and the Hatay Graben of Turkey, and implying a fluvial landscape response time of 1.6 to 2.7 Myr. We explore the relative controls of drainage area and precipitation on these retreat rates, and conclude that while climate variation and fault throw rate partially explain the variations seen, lithology remains a potentially important but poorly characterised variable. Copyright © 2016 John Wiley & Sons, Ltd.