The effect of riparian tree roots on the mass‐stability of riverbanks

Plants interact with and modify the processes of riverbank erosion by altering bank hydrology, flow hydraulics and bank geotechnical properties. The physically based slope stability model GWEDGEM was used to assess how changes in bank geotechnical properties due to the roots of native Australian riparian trees affected the stability of bank sections surveyed along the Latrobe River. Modelling bank stability against mass failure with and without the reinforcing effects of River Red Gum (Eucalyptus camaldulensis) or Swamp Paperbark (Melaleuca ericifolia) indicates that root reinforcement of the bank substrate provides high levels of bank protection. The model indicates that the addition of root reinforcement to an otherwise unstable bank section can raise the factor of safety (F _s) from F _s = 1·0 up to about F _s = 1·6. The addition of roots to riverbanks improves stability even under worst‐case hydrological conditions and is apparent over a range of bank geometries, varying with tree position. Trees growing close to potential failure plane locations, either low on the bank or on the floodplain, realize the greatest bank reinforcement. Copyright © 2000 John Wiley & Sons, Ltd.     

Influence of seepage undercutting on the stability of root‐reinforced streambanks

Several mechanisms contribute to streambank failure including fluvial toe undercutting, reduced soil shear strength by increased soil pore‐water pressure, and seepage erosion. Recent research has suggested that seepage erosion of noncohesive soil layers undercutting the banks may play an equivalent role in streambank failure to increased soil pore‐water pressure. However, this past research has primarily been limited to laboratory studies of non‐vegetated banks. The objective of this research was to utilize the Bank Stability and Toe Erosion Model (BSTEM) in order to determine the importance of seepage undercutting relative to bank shear strength, bank angle, soil pore‐water pressure, and root reinforcement. The BSTEM simulated two streambanks: Little Topashaw Creek and Goodwin Creek in northern Mississippi. Simulations included three bank angles (70° to 90°), four pore‐water pressure distributions (unsaturated, two partially saturated cases, and fully saturated), six distances of undercutting (0 to 40 cm), and 13 different vegetation conditions (root cohesions from 0·0 to 15·0 kPa). A relative sensitivity analysis suggested that BSTEM was approximately three to four times more sensitive to water table position than root cohesion or depth of seepage undercutting. Seepage undercutting becomes a prominent bank failure mechanism on unsaturated to partially saturated streambanks with root reinforcement, even with undercutting distances as small as 20 cm. Consideration of seepage undercutting is less important under conditions of partially to fully saturated soil pore‐water conditions. The distance at which instability by undercutting became equivalent to instability by increased soil pore‐water pressure decreased as root reinforcement increased, with values typically ranging between 20 and 40 cm at Little Topashaw Creek and between 20 and 55 cm at Goodwin Creek. This research depicts the baseline conditions at which seepage undercutting of vegetated streambanks needs to be considered for bank stability analyses. Copyright © 2008 John Wiley & Sons, Ltd.     

Soil moisture causes dynamic adjustments to root reinforcement that reduce slope stability

In steep soil‐mantled landscapes, the initiation of shallow landslides is strongly controlled by the distribution of vegetation, whose roots reinforce the soil. The magnitude of root reinforcement depends on the number, diameter distribution, orientation and the mechanical properties of roots that cross potential failure planes. Understanding how these properties vary in space and time in forests remains a significant challenge. Here we test the hypothesis that spatio‐temporal variations in root reinforcement along a hillslope occur as a function of topographic soil moisture gradients. To test this hypothesis we compared root reinforcement measurements from relatively dry, divergent noses to relatively wet, convergent hollows in the southern Appalachian Mountains, North Carolina, USA. Our initial results showed that root reinforcement decreased in areas of higher soil moisture because the tensile strength of roots decreased. A post hoc laboratory experiment further demonstrated that root tensile strength decreased as root moisture content increased. This effect is consistent with other experiments on stem woods showing that increased water content in the cell wall decreases tensile strength. Our experimental data demonstrated that roots can adjust to changes in the external root moisture conditions within hours, suggesting that root moisture content will change over the timescale of large storm events (hours–days). We assessed the effects of the dynamic changes in root tensile strength to the magnitude of apparent cohesion within the infinite slope stability model. Slopes can be considerably less stable when precipitation‐driven increases in saturated soil depth both increase pore pressures and decrease root reinforcement. Copyright © 2016 John Wiley & Sons, Ltd.     

Modelling biome‐scale root reinforcement and slope stability

Rapid changes in the composition of hillslope vegetation due to a combination of changing climate and land use make estimating slope stability a significant challenge. The dynamics of root growth on any individual hillslope result in a wide range of root distributions and strengths that are reflected as up to an order of magnitude variability in root cohesion. Hence the challenge of predicting the magnitude of root reinforcement for hillslopes requires both an understanding of the magnitude and variability of root distributions and material properties (e.g. tensile strength, elasticity). Here I develop a model for estimating the reinforcement provided by plant roots based on the distribution of biomass measured at the biome level and a compilation of root tensile strength measurements measured across a range of vegetation types. The model modifies the Wu/Waldron method of calculating root cohesion to calculate the average lateral root cohesion and its variability with depth using the Monte Carlo method. The model was validated in two ways, the first against the predicted depth‐reinforcement characteristics of Appalachian soils and the second using a global dataset of landslides. Model results suggest that the order of magnitude difference in root cohesions measured on individual hillslopes can be captured by the Monte Carlo approach and provide a simple tool to estimate root reinforcement for data‐poor areas. The model also suggests that future hotspots of slope instability will occur in areas where land use and climate convert forest to grassland, rather than changes between different forest structures or forest and shrubland. Copyright © 2018 John Wiley & Sons, Ltd.     

Physical environmental controls on riparian root profiles associated with black poplar (Populus nigra L.) along the Tagliamento River,Italy

Tree roots contribute to the resistance of riparian sediments to physical deformation and disintegration. Understanding reinforcement by roots requires information on root distributions within riparian soils and sediments. Continuous‐depth models or curves have been proposed to describe vertical root density variations, providing useful indicators of the types of function that may be appropriate to riparian trees, but have generally been estimated for terrestrial species or broad vegetation types rather than riparian species or environments. We investigated vertical distributions of roots >0.1 mm diameter of a single riparian tree species (Populus nigra L.) along the middle reaches of a single river (Tagliamento River, Italy), where Populus nigra dominates the riparian woodland. Root density (hundreds m^?2) and root area ratio (RAR in cm² m^?2) were measured within 10 cm depth increments of 24 excavated bank profiles across nine sites. Sediment samples, extracted from distinct strata within the profiles, were analysed for moisture content, organic matter content and particle size. Statistical analyses identified two groups of wetter and drier profiles and five sediment types. Following log_e‐transformation of root density and RAR, linear regression analysis explored their variation with depth and, using dummy variables, any additional influence of moisture and sediment type. Significant linear regression relationships were estimated between both root density and RAR and depth which explained only 15% and 8% of the variance in the data. Incorporating moisture and then sediment characteristics into the analysis increased the variance explained in root density to 29% and 36% and in RAR to 14% and 26%. We conclude that riparian tree root density and RAR are highly spatially variable and are poorly explained by depth alone. Complex riparian sedimentary structures and moisture conditions are important influences on root distributions and so need to be incorporated into assessments of the contribution of roots to river bank reinforcement. Copyright © 2016 John Wiley & Sons, Ltd.     

Reduced‐complexity flow routing models for sinuous single‐thread channels: intercomparison with a physically‐based shallow‐water equation model

Reduced‐complexity models of fluvial processes use simple rules that neglect much of the underlying governing physics. This approach is justified by the potential to use these models to investigate long‐term and/or fundamental river behaviour. However, little attention has been given to the validity or realism of reduced‐complexity process parameterizations, despite the fact that the assumptions inherent in these approaches may limit the potential for elucidating the behaviour of natural rivers. This study presents two new reduced‐complexity flow routing schemes developed specifically for application in single‐thread rivers. Output from both schemes is compared with that from a more sophisticated model that solves the depth‐averaged shallow water equations. This comparison provides the first demonstration of the potential for deriving realistic predictions of in‐channel flow depth, unit discharge, energy slope and unit stream power using simple flow routing schemes. It also highlights the inadequacy of modelling unit stream power, shear stress or sediment transport capacity as a function of local bed slope, as has been common practice in a number of previous reduced‐complexity models. Copyright © 2009 John Wiley & Sons, Ltd.     

Flow behaviour,suspended sediment transport and transmission losses in a small (sub‐bank‐full) flow event in an Australian desert stream

The behaviour of a discrete sub‐bank‐full flow event in a small desert stream in western NSW, Australia, is analysed from direct observation and sediment sampling during the flow event and from later channel surveys. The flow event, the result of an isolated afternoon thunderstorm, had a peak discharge of 9 m³/s at an upstream station. Transmission loss totally consumed the flow over the following 7·6 km. Suspended sediment concentration was highest at the flow front (not the discharge peak) and declined linearly with the log of time since passage of the flow front, regardless of discharge variation. The transmission loss responsible for the waning and eventual cessation of flow occurred at a mean rate of 13.2% per km. This is quite rapid, and is more than twice the corresponding figure for bank‐full flows estimated by Dunkerley (1992) on the same stream system. It is proposed that transmission losses in ephemeral streams of the kind studied may be minimized in flows near bank‐full stage, and be higher in both sub‐bank‐full and overbank flows. Factors contributing to enhanced flow loss in the sub‐bank‐full flow studied included abstractions of flow to pools, scour holes and other low points along the channel, and overflow abstractions into channel filaments that did not rejoin the main flow. On the other hand, losses were curtailed by the shallow depth of banks wetted and by extensive mud drapes that were set down over sand bars and other porous channel materials during the flow. Thus, in contrast with the relatively regular pattern of transmission loss inferred from large floods, losses from low flows exhibit marked spatial variability and depend to a considerable extent on streamwise variations in channel geometry, in addition to the depth and porosity of channel perimeter sediments. Copyright © 1999 John Wiley & Sons, Ltd.     

Impact of root architecture on the erosion‐reducing potential of roots during concentrated flow

Many studies focus on the effects of vegetation cover on water erosion rates, whereas little attention has been paid to the effects of the below ground biomass. Recent research indicates that roots can reduce concentrated flow erosion rates significantly. In order to predict this root effect more accurately, this experimental study aims at gaining more insight into the importance of root architecture, soil and flow characteristics to the erosion‐reducing potential of roots during concentrated flow. Treatments were (1) bare, (2) grass (representing a fine‐branched root system), (3) carrots (representing a tap root system) and (4) carrots and fine‐branched weeds (representing both tap and fine‐branched roots). The soil types tested were a sandy loam and a silt loam. For each treatment, root density, root length density and mean root diameter (D) were assessed. Relative soil detachment rates and mean bottom flow shear stress were calculated. The results indicate that tap roots reduce the erosion rates to a lesser extent compared with fine‐branched roots. Different relationships linking relative soil detachment rate with root density could be established for different root diameter classes. Carrots with very fine roots (D < 5 mm) show a similar negative exponential relationship between root density and relative soil detachment rate to grass roots. With increasing root diameter (5 < D < 15 mm) the erosion‐reducing effect of carrot type roots becomes less pronounced. Additionally, an equation estimating the erosion‐reducing potential of root systems containing both tap roots and fine‐branched roots could be established. Moreover, the erosion‐reducing potential of grass roots is less pronounced for a sandy loam soil compared with a silt loam soil and a larger erosion‐reducing potential for both grass and carrot roots was found for initially wet soils. For carrots grown on a sandy loam soil, the erosion‐reducing effect of roots decreases with increasing flow shear stress. For grasses, grown on both soil types, no significant differences could be found according to flow shear stress. The erosion‐reducing effect of roots during concentrated flow is much more pronounced than suggested in previous studies dealing with interrill and rill erosion. Root density and root diameter explain the observed erosion rates during concentrated flow well for the different soil types tested. Copyright © 2007 John Wiley & Sons, Ltd.     

Long‐term growth of a valley‐bottom gully,western Iowa

Growth of a permanent, valley‐bottom gully from 1964 to 2000 was determined annually from survey and sediment‐discharge data and compared with runoff and base?ow discharges. Data were analysed to test the hypothesis that rates of gully growth decay exponentially with time in response to shrinking catchment area caused by gully enlargement. Also, monthly values of growth rates and runoff, averaged over the 36‐year record, were analysed with mass‐wasting data to determine the extent to which colluvium availability affected growth rates seasonally. From 1964 to 2000, the gully volume increased by 9200 m³, accounting for 34 per cent of sediment yield from the watershed. There were tight power‐law relationships between annual growth rates and annual runoff, with runoff exponents of 1·57 and 1·30 for headward and volumetric growth, respectively. Increases in gully length, area, and volume were ?tted successfully assuming an exponential decay in growth rate with time. Rather than being due to a decrease in catchment area, however, the decline in growth rate was caused by a 77 per cent decrease in the ratio of runoff to base?ow, which also widened the gully and reduced the mean slope of its banks. Order‐of‐magnitude seasonal changes in erosion ef?ciency, de?ned as the fraction of stream power used to evacuate sediment from the gully, were roughly correlated with colluvium availability, as indicated by seasonal changes in the number of bank mass‐wasting events. No more than 2·2 per cent of stream power was used to evacuate sediment during any month. This study demonstrates the danger of attributing declining rates of gully growth to a shrinking catchment area if corroborative runoff and base?ow data are not available. Moreover, it illustrates that stream power alone provides only a rough and physically indirect measure of erosion potential. Copyright © 2004 John Wiley & Sons, Ltd.     

Modeling the functional influence of vegetation type on streambank cohesion

The important role of vegetation in adding cohesion and stabilizing streambanks has been widely recognized in several aspects of fluvial geomorphology, including stream restoration and studies of long‐term channel change. Changes in planform between braided, meandering, and anabranching forms have been attributed to the impacts of vegetation on hydraulic roughness and bank stability. However, these studies focus either on flume studies where analog vegetation is used, or case studies featuring one species, which is commonly invasive. We present functional differences of bank‐stabilizing root characteristics and added cohesion, with vegetation categorized as woody and non‐woody and by the vegetation groups of trees, shrubs, graminoids, and forbs. We analyzed root morphology and tensile strength of 14 species common to riparian areas in the southern Rocky Mountains, in field sites along streambanks in the montane and subalpine zones of the Colorado Front Range. Using the vegetation root component (RipRoot) of a physically‐based bank stability model (BSTEM), we estimated the added cohesion for various sediment textures with the addition of each of the 14 species. Significant differences exist between woody and non‐woody vegetation and between the four vegetation categories with respect to the coefficient of the root tensile strength curve, lateral root extent, and maximum root diameter. Woody vegetation (trees and shrubs) have higher values of all three parameters than non‐woody species. Tree roots add significantly more cohesion to streambanks than forb roots. Additionally, rhizomes may play an important role in determining the reach‐scale effects of roots on bank stabilization. Differences in root characteristics and added cohesion among vegetation categories have several important implications, including determining the likelihood of planform change, developing guidelines for the use of bank‐stabilizing vegetation, and linking the effect of vegetation to geomorphic structure that can benefit ecosystem functioning. Copyright © 2014 John Wiley & Sons, Ltd.     

Evaluating the effectiveness of road‐crossing drainage culverts in ephemeral streams

The present study proposes a method for evaluating the effectiveness of road‐crossing drainage culverts in ephemeral streams. This approach is focused on estimating the culvert capacity in road–stream crossings and the probable runoff generated on the road from hydrological thresholds associated with hydromorphological criteria. In particular, discharges at bankfull and flood‐prone stages have been used in combination with 2.5 and 100‐year peak discharges. Different hydraulic variables have been considered for calculating the discharge through culverts under these conditions (e.g. tailwater and headwater depth, inlet control, pipe roughness, pipe cross‐area and slope, pipe outlet velocity, critical water depth, and flow rate over the road). Geomorphological factors such as bed stability, bed load transport, and channel roughness have also been considered because of their potential for obstructing the drains in this type of channel. In addition, a potential obstruction index (PI_OBSTR) has been calculated, as a dependent parameter of the obstacle index (I_OBST) and the potential build‐up of coarse sediments (PB_CS). The study has been carried out on the Mediterranean coast in the region of Murcia (Spain), where there are numerous examples of road–stream crossings equipped with culverts in ephemeral channels that could cause highly dangerous situations for road traffic. Copyright © 2012 John Wiley & Sons, Ltd.     

A new model to analyse the impact of woody riparian vegetation on the geotechnical stability of riverbanks

We present a geotechnical stability analysis for the planar failure of riverbanks, which incorporates the effects of root reinforcement and surcharge for mature stands of woody riparian vegetation. The analysis relies on a new method of representing the root distribution in the soil, which evaluates the effects of the vegetation's position on the bank. The model is used in a series of sensitivity analyses performed for a wide range of bank morphological (bank slope and height) and sedimentological (bank cohesion and friction angle) conditions, enabling discrimination of the types of bank environment for which vegetation has an effect on bank stability. The results indicate that woody vegetation elements have a maximal impact on bank stability when they are located at the ends of the incipient failure plane (i.e. at the bank toe or at the intersection of the failure plane with the floodplain) and that vegetation has a greater effect on net bank stability when it is growing on low, shallow, banks comprised of weakly cohesive sediments. However, the magnitude of these effects is limited, with vegetation typically inducing changes (relative to non‐vegetated banks) in simulated factors of safety of less than 5%. If correct, this suggests that the well documented effects of vegetation on channel morphology must be related to alternative process mechanisms (such as the interaction of vegetation with river flows) rather than the mechanical effects of vegetation on bank failure, except in special cases where the equivalent non‐vegetated bank has a highly marginal stability status. Copyright © 2007 John Wiley & Sons, Ltd.     

The influence of riparian vegetation on near‐bank turbulence: a flume experiment

Measurements from a fixed‐bed, Froude‐scaled hydraulic model of a stream in northeastern Vermont demonstrate the importance of forested riparian vegetation effects on near‐bank turbulence during overbank flows. Sections of the prototype stream, a tributary to Sleepers River, have increased in channel width within the last 40 years in response to passive reforestation of its riparian zone. Previous research found that reaches of small streams with forested riparian zones are commonly wider than adjacent reaches with non‐forested, or grassy, vegetation; however, driving mechanisms for this morphologic difference are not fully explained. Flume experiments were performed with a 1:5 scale, simplified model of half a channel and its floodplain, mimicking the typical non‐forested channel size. Two types of riparian vegetation were placed on the constructed floodplain: non‐forested, with synthetic grass carpeting; and forested, where rigid, randomly distributed, wooden dowels were added. Three‐dimensional velocities were measured with an acoustic Doppler velocimeter at 41 locations within the channel and floodplain at near‐bed and 0·6‐depth elevations. Observations of velocity components and calculations of turbulent kinetic energy (TKE), Reynolds shear stress and boundary shear stress showed significant differences between forested and non‐forested runs. Generally, forested runs exhibited a narrow band of high turbulence between the floodplain and main channel, where TKE was roughly two times greater than TKE in non‐forested runs. Compared to non‐forested runs, the hydraulic characteristics of forested runs appear to create an environment with higher erosion potential. Given that sediment entrainment and transport can be amplified in flows with high turbulence intensity and given that mature forested stream reaches are wider than comparable non‐forested reaches, our results demonstrated a possible driving mechanism for channel widening during overbank flow events in stream reaches with recently reforested riparian zones. Copyright © 2007 John Wiley & Sons, Ltd.     

Assessing the effect of vegetation‐related bank strength on channel morphology and stability in gravel‐bed streams using numerical models

Bank strength due to vegetation dominates the geometry of small stream channels, but has virtually no effect on the geometry of larger ones. The dependence of bank strength on channel scale affects the form of downstream hydraulic geometry relations and the meandering‐braiding threshold. It is also associated with a lateral migration threshold discharge, below which channels do not migrate appreciably across their floodplains. A rational regime model is used to explore these scale effects: it parameterizes vegetation‐related bank strength using a dimensionless effective cohesion, C_r*. The scale effects are explored primarily using an alluvial state space defined by the dimensionless formative discharge, Q*, and channel slope, S, which is analogous to the Q–S diagrams originally used to explore meandering‐braiding thresholds. The analyses show that the effect of vegetation on both downstream hydraulic geometry and the meandering‐braiding threshold is strongest for the smallest streams in a watershed, but that the effect disappears for Q* > 10⁶. The analysis of the migration threshold suggests that the critical discharge ranges from about 5 m³/s to 50 m³/s, depending on the characteristic rooting depth for the vegetation. The analysis also suggests that, where fires frequently affect riparian forests, channels may alternate between laterally stable gravel plane‐bed channels and laterally active riffle‐pool channels. These channels likely do not exhibit the classic dynamic equilibrium associated with alluvial streams, but instead exhibit a cyclical morphologic evolution, oscillating between laterally stable and laterally unstable end‐members with a frequency determined by the forest fire recurrence interval. Copyright © 2008 John Wiley & Sons, Ltd.     

Creek enlargement in a low‐energy degrading saltmarsh in southern England

A low‐energy saltmarsh in the Beaulieu River Estuary, southern England was investigated. A geomorphological survey revealed that the creek bank geometry was characterized by the presence of cantilevers, a result of the protection provided by roots over the upper part of the bank. The saltmarsh deposits, consisting mainly of clay and organic matter, have a high resistance to flow‐induced erosion. Short‐term hydrographic deployments revealed that the tidal currents and waves recorded were insufficient to cause erosion of the bank surface. However, pin measurements over a 2‐year period revealed that the tidal creeks within the saltmarsh did experience bank erosion, particularly below the cantilevers, in spite of this low‐energy setting. Bank face erosion was therefore considered to be related to long‐term processes. The bases of the cantilevers were found to be located at a precise level, in relation to the tides. Water level data over a 2‐year period were examined against erosion measured below the cantilevers. The results suggest that the erosion on the bank faces, particularly below the cantilevers, is associated with the frequency of water level variations and long‐term submergence/emergence cycles, which can decrease the bonds between the particles and enable erosion by low tidal and wind‐wave currents within this low‐energy environment. This mechanism is probably responsible for tidal creek enlargement via erosion of the bank face and subsequent bank failure, a process which acts over a long temporal scale (1–10 years). Copyright © 2010 John Wiley & Sons, Ltd.     

Experimental analysis of cross‐sectional flow motion in a large amplitude meandering bend

Flow in meandering bends is characterized by the formation of a large cross‐sectional central‐region circulation cell. The width‐to‐depth ratio is one of the most important parameters affecting the entity of the cross‐circulation motion. In steep outside bends, beside the central‐region cell, a counter‐rotating circulation cell often forms in the upper part of the outer‐bank. In spite of its practical importance, the evolving mechanisms of both the circulation cells and their role on boundary shear stress distribution in bends are not yet fully understood. The aim of the present paper is to gain some insight into how cross‐sectional flow motion evolves along meandering bends. Experiments have been carried out in a laboratory meandering channel of large amplitude, over a deformed‐rigid bed, for two values of the width‐to‐depth ratio. The three‐dimensional flow velocity field has been measured in detail at five cross‐sections, almost equally spaced along the channel reach between two consecutive apex sections. The measurements have been carried out on a fine grid by an acoustic Doppler velocity profiler. The distributions of the cross‐sectional flow (e.g. cross‐sectional flow velocity, net transversal flux) and turbulent kinetic energy are analyzed in each investigated section. Measurements show that the counter‐rotating circulation cell is evident only in the case of ‘small’ width‐to‐depth ratio. Such circulation cell begins at the bend entrance and it is fully developed at the bend apex; then it decays. At the bend apex, the core of maximum velocity is found near the bed at about the separation between the central and the outer‐bank circulation cells. Moreover, the presence of the counter‐rotating circulation cell allows the bank shear stress to maintain low values in the outer‐side of the bend. Copyright © 2010 John Wiley & Sons, Ltd.     

Detailed spatio‐temporal sediment supply reconstruction using tree roots data

Floods are an important geomorphic agent that accelerate sediment supply from bank failures. The quantitative proportions supplied by lateral inputs and the transport conditions of the channel can create local or extended accumulation zones within the channel reaches. These accumulation zones play an important role in the geomorphic regime of the stream. Knowledge of long‐term history of sediment supply is necessary to determine how these input and deposition forms developed. This study introduces a new approach for the quantification of past sediment supply via lateral erosion (incised banks and individual bank failures), using a case study of the confluence of three partial tributaries in the accumulation zone in the Outer Western Carpathians. For each tributary, as well as the channel reach downstream of the confluence zone, we calculated the mean of the largest bed particles and the unit stream power as indicators of transport capacity. We found that two of the tributaries supply significant amounts of sediment to the accumulation zone because of their higher unit stream power related to their higher transport potential, and observed coarser bed sediment. Seventy‐three bank failures with a total volume 395.5 m³ were mapped, and the sediment supply volume was dated using dendrogeomorphic analysis of 114 scarred tree roots (246 samples). The total volume of the dated sediment supply in the individual tributaries was 193.9 m³, whereas the volume of erosion in the accumulation zone was only 4.9 m³ for a period of approximately 30 years. The period represented by the dated tree roots included 12 years in which erosion events occurred and impacted the total sediment budget in the study area. Although sediment supply was greater than erosion in the accumulation zone, there are no present‐day signs of accretion. The rupture of a dam in an old pond (which is situated approximately 50 m below the accumulation zone) probably increased the transport conditions in the accumulation zone so that it balanced the high sediment supply from individual tributaries. Copyright © 2016 John Wiley & Sons, Ltd.     

Spatial variability of three‐dimensional Reynolds stresses in a developing channel bend

Experimental results of the mean flow field and turbulence characteristics for flow in a model channel bend with a mobile sand bed are presented. Acoustic Doppler velocimeters (ADVs) were used to measure the three components of instantaneous velocities at multiple cross sections in a 135° channel bend for two separate experiments at different stages of clear water scour conditions. With measurements at multiple cross sections through the bend it was possible to map the changes in both the spatial distribution of the mean velocity field and the three Reynolds shear stresses. Turbulent stresses are known to contribute to sediment transport and the three‐dimensionality inherent to flow in open channel bends presents a useful case for determining specific relations between three‐dimensional turbulence and sediment entrainment and transport. These measurements will also provide the necessary data for validating numerical simulations of turbulent flow and sediment transport. The results show that the magnitude and distribution of three‐dimensional Reynolds stresses increase through the bend, with streamwise‐cross stream and cross stream‐vertical components exceeding the maximum principal Reynolds stress through the bend. The most intriguing observation is that near‐bed maximum positive streamwise‐cross stream Reynolds stress coincides with the leading edge of the outer bank scour hole (or thalweg), while maximum cross stream‐vertical Reynolds stress (in combination with high negative streamwise‐cross stream Reynolds stress near the bend apex) coincides with the leading edge of the inner bank bar. Maximum Reynolds stress and average turbulent kinetic energy appear to be greater and more localized over the scour hole before final equilibrium scour is reached. This suggests that the turbulent energy in the flow is higher while the channel bed is developing, and both lower turbulent energy and a broader distribution of turbulent stresses near the bed are required for cessation of particle mobilization and transport. Copyright © 2010 John Wiley & Sons, Ltd.     

Water uptake by saltcedar (Tamarix ramosissima) in a desert riparian forest: responses to intra‐annual water table fluctuation

There is considerable interest in naturalizing flow regime on managed rivers to slow the spread of saltcedar (Tamarix ramosissima) invasion in southwestern USA or to preserve riparian forests dominated by saltcedar and other species in northwestern China. However, little is known about the responses of established saltcedar in water sources to frequent intra‐annual fluctuation of water table resulting from this new, more dynamic flow regime. This study investigates how saltcedar at a riparian site in the middle reaches of the Heihe River, northwest China, responds in water sources use to intra‐annual water table fluctuations. Stable oxygen isotope was employed to determine accurate depth at which saltcedar obtains its water supply, and soil moisture monitoring was used to determine sources of plant‐available soil water. We found that the primary zone of water uptake by saltcedar were stable at 25–60 cm depth, but the water sources used by saltcedar switched between groundwater and soil moisture with the water table fluctuations. Saltcedar derived its water from groundwater when water table was at depth less than 60 cm but switched to soil moisture at 25–60 cm depth when water table declined. It is supposed that the well‐developed clay layer at 60–80 cm depth constrained lateral roots of saltcedar to the soil layers above 60 cm, while the fine‐textured soils at this site, which were periodically resaturated by rising groundwater before the stored soil moisture had become depleted, provided an important water reservoir for saltcedar when groundwater dropped below the primary zone of fine roots. The root distribution of saltcedar may also be related to local groundwater history. The quick decline in water table in the early 1980s when the riparian saltcedar had established may strand its roots in the shallow unsaturated zone. We suggested that raising the water table periodically instead of maintaining it invariably above the rooting depth could sustain desired facultative phreatophytes while maximizing water deliveries. Copyright © 2015 John Wiley & Sons, Ltd.