Transport of moderately sorted gravel at low bed shear stresses: The role of fine sediment infiltration

A reliable estimation of sediment transport in gravel‐bed streams is important for various practical engineering and biological studies (e.g., channel stability design, bed degradation/aggradation, restoration of spawning habitat). In the present work, we report original laboratory experiments investigating the transport of gravel particles at low bed shear stresses. The laboratory tests were conducted under unsteady flow conditions inducing low bed shear stresses, with detailed monitoring of the bed topography using a laser scanner. Effects of bed surface arrangements were documented by testing loose and packed bed configurations. Effects of fine sediments were examined by testing beds with sand, artificial fine sand or cohesive silt infiltrated in the gravel matrix. Analysis of the experimental data revealed that the transport of gravel particles depends upon the bed arrangement, the bed material properties (e.g., size and shape, consolidation index, permeability) and the concentration of fine sediments within the surface layer of moving grains. This concentration is directly related to the distribution of fine particles within the gravel matrix (i.e., bottom‐up infiltration or bridging) and their transport mode (i.e., bedload or suspended load). Compared to loose beds, the mobility of gravel is reduced for packed beds and for beds clogged from the bottom up with cohesive fine sediments; in both cases, the bed shear stress for gravel entrainment increases by about 12%. On the other hand, the mobility of gravel increases significantly (bed shear stress for particle motion decreasing up to 40%) for beds clogged at the surface by non‐cohesive sand particles. Copyright © 2017 John Wiley & Sons, Ltd.     

The zoogeomorphology of case-building caddisfly: Quantifying sediment use

Caddisfly (Trichoptera) larvae are an abundant and widespread aquatic insect group characterized by the construction of silk structures, including nets and cases. Case-building caddisfly have the potential to modify the sorting and mobility of sand and fine gravel via: (1) case construction, resulting in altered sediment properties; (2) transporting sediment incorporated into cases over the river bed; and (3) changing the structure of river beds via burrowing activity. To investigate these mechanisms, it is necessary to understand the mass, size distribution and spatial variability of sediment use by case-building caddisfly larvae. We quantified the mineral sediment used by individuals and communities of case-building caddisfly in 27 samples, from three sites on a gravel-bed stream. The mass and size distribution of sediment in individual cases varied between taxa (mass = 0.001–0.83 g, D₅₀ = 0.17–4 mm). The mean mass of sediment used by the caddisfly community was 38 g m⁻² and varied locally. Sediment use was predominantly coarse sand (D₅₀ = 1 mm). 64% of sediment use was attributable to Agapetus fuscipes (Glossosomatidae). Due to within-species variability in case mass, the abundance of most taxa, including A. fuscipes, was only weakly associated with the mass of sediment used by this species, at the river scale. Whilst the caddisfly community used a small percentage of the total sediment available (average 2.99% of the 1–1.4 mm size fraction), A. fuscipes used more fine sediment in their cases at sites where it was more available. Despite variability in local habitat, all sites supported diverse case-building caddisfly communities utilizing mineral sediment. Consequently, geomorphological effects of case-building caddisfly are potentially widespread. The results provide novel insights into the specific grain sizes and quantities of fine sediment used by caddisfly larvae, which represents an important step towards understanding their zoogeomorphic activities. © 2019 The Authors. Earth Surface Processes and Landforms Published by John Wiley & Sons Ltd.     

Reduced bed material stability and increased bedload transport caused by foraging fish: a flume study with juvenile Barbel (Barbus barbus)

The plants and animals that inhabit river channels may act as zoogeomorphic agents affecting the nature and rates of sediment recruitment, transport and deposition. The impact of benthic‐feeding fish, which disturb bed material sediments during their search for food, has received very little attention, even though benthic feeding species are widespread in rivers and may collectively expend significant amounts of energy foraging across the bed. An ex situ experiment was conducted to investigate the impact of a benthic feeding fish (Barbel Barbus barbus) on particle displacements, bed sediment structures, gravel entrainment and transport fluxes. In a laboratory flume changes in bed surface topography were measured and grain displacements examined when an imbricated, water‐worked bed of 5.6 to 16 mm gravels was exposed to feeding juvenile Barbel (on average, 0.195 m in length). Grain entrainment rates and bedload fluxes were measured under a moderate transport regime for substrates that had been exposed to feeding fish and control substrates which had not. On average, approximately 37% of the substrate, by area, was modified by foraging fish during a four‐hour treatment period, resulting in increased microtopographic roughness and reduced particle imbrication. Structural changes by fish corresponded with an average increase in bedload flux of 60% under entrainment flows, whilst on average the total number of grains transported during the entrainment phase was 82% higher from substrates that had been disturbed by Barbel. Together, these results indicate that by increasing surface microtopography and undoing the naturally stable structures produced by water working, foraging can increase the mobility of gravel‐bed materials. An interesting implication of this result is that by increasing the quantity of available, transportable sediment and lowering entrainment thresholds, benthic feeding might affect bedload fluxes in gravel‐bed rivers. The evidence presented here is sufficient to suggest that further investigation of this possibility is warranted. Copyright © 2014 John Wiley & Sons, Ltd.     

Controls on spatial and temporal variations in sand delivery to salmonid spawning riffles

Fine sediment infiltration into gravel interstices is known to be detrimental to incubating salmonid embryos. Infiltration into spawning riffles can show large spatial variations at the scale of a morphological unit and over time, with significant implications for embryo survival. Furthermore, some process‐based infiltration studies, and incubation‐to‐emergence models assume that fines are delivered to redds via suspension rather than bedload. This process‐based 12‐month study examined spatial patterns of predominantly sand infiltration into gravels in an upland trout stream, using infiltration baskets. An assessment of Rouse numbers for infiltrated sand indicated that it was transported predominantly as bedload at flow peaks. Clear temporal and spatial patterns existed, with highest rates of infiltration strongly associated with higher discharges (r² = 0.7, p < .05). Seasonal variations in the delivery of different grain sizes were also a feature, with enhanced contributions of 0.5–2 mm sediment during elevated winter flows and 0.125–0.5 mm sediment during spring and summer; the latter is potentially harmful to the later stages of embryo incubation. Clear spatial patterns were also evident across riffles, with highest rates of infiltration tending to occur in areas of lower relative roughness—the areas competent to transport sand for longer periods. Incubation‐to‐emergence models should take into consideration spatial patterns of fine sediment dynamics at the pool–riffle scale, to improve prediction.     

Evaluating fine sediment mobilization and storage in a gravel‐bed river using controlled reservoir releases

Two controlled flow events were generated by releasing water from a reservoir into the Olewiger Bach, located near Trier, Germany. This controlled release of near bank‐full flows allowed an investigation of the fine sediment (<63 µm) mobilized from channel storage. Both a winter (November) and a summer (June) release event were generated, each having very different antecedent flow conditions. The characteristics of the release hydrographs and the associated sediment transport indicated a reverse hysteresis with more mass, but smaller grain sizes, moving on the falling limb. Fine sediment stored to a depth of 10 cm in the gravels decreased following the release events, indicating the dynamic nature and importance of channel‐stored sediments as source materials during high flow events. Sediment traps, filled with clean natural gravel, were buried in riffles before the release of the reservoir water and the total mass of fine sediment collected by the traps was measured following the events. Twice the mass of fine sediment was retained by the gravel traps compared with the natural gravels, which may be due to their altered porosity. Although the amount of fine sediment collected by the traps was not significantly related to measures of gravel structure, it was found to be significantly correlated to measures of local flow velocity and Froude number. A portion of the traps were fitted with lids to restrict surface exchange of water and sediment. These collected the highest amounts of event‐mobilized sediments, indicating that inter‐gravel lateral flows, not just surface infiltration of sediments, are important in replenishing and redistributing the channel‐stored fines. These findings regarding the magnitude and direction of fine sediment movement in gravel beds are significant in both a geomorphic and a biological context. Copyright © 2006 John Wiley & Sons, Ltd.     

Spatial variations in surface sediment structure in riffle–pool sequences: a preliminary test of the Differential Sediment Entrainment Hypothesis (DSEH)

Riffle–pool sequences are maintained through the preferential entrainment of sediment grains from pools rather than riffles. This preferential entrainment has been attributed to a reversal in the magnitude of velocity and shear stress under high flows; however the Differential Sediment Entrainment Hypothesis (DSEH) postulates that differential entrainment can instead result from spatial sedimentological contrasts. Here we use a novel suite of in situ grain‐scale field measurements from a riffle–pool sequence to parameterize a physically‐based model of grain entrainment. Field measurements include pivoting angles, lift forces and high resolution digital elevation models (DEMs) acquired using terrestrial laser scanning, from which particle exposure, protrusion and surface roughness were derived. The entrainment model results show that grains in pools have a lower critical entrainment shear stress than grains in either pool exits or riffles. This is because pool grains have looser packing, hence greater exposure and lower pivoting angles. Conversely, riffle and pool exit grains have denser packing, lower exposure and higher pivoting angles. A cohesive matrix further stabilizes pool exit grains. The resulting predictions of critical entrainment shear stress for grains in different subunits are compared with spatial patterns of bed shear stress derived from a two‐dimensional computational fluid dynamics (CFD) model of the reach. The CFD model predicts that, under bankfull conditions, pools experience lower shear stresses than riffles and pool exits. However, the difference in sediment entrainment shear stress is sufficiently large that sediment in pools is still more likely to be entrained than sediment in pool exits or riffles, resulting in differential entrainment under bankfull flows. Significantly, this differential entrainment does not require a reversal in flow velocities or shear stress, suggesting that sedimentological contrasts alone may be sufficient for the maintenance of riffle–pool sequences. This finding has implications for the prediction of sediment transport and the morphological evolution of gravel‐bed rivers. Copyright © 2012 John Wiley & Sons, Ltd.     

Thresholds and relations for soil‐hydraulic and soil‐physical properties as a function of burn severity 4 years after the 2011 Las Conchas Fire,New Mexico,USA

Wildfire effects on soil‐physical and ‐hydraulic properties as a function of burn severity are poorly characterized, especially several years after wildfire. A stratified random sampling approach was used in 2015 to sample seven sites representing a spectrum of remotely sensed burn severity in the area impacted by the 2011 Las Conchas Fire in New Mexico, USA. Replicate samples from each site were analysed in the laboratory. Linear and linear indicator regression were used to assess thresholds in soil‐physical and ‐hydraulic properties and functional relations with remotely sensed burn severity. Significant thresholds were present for initial soil‐water content (θ_i) at 0–6 cm depth between the change in the Normalized Burn Ratio (dNBR) equal to 618–802, for bulk density (ρ_b) at 3–6 cm between dNBR equal to 416–533, for gravel fraction at 0–1 cm between dNBR equal to 416–533, for fines (the silt + clay fraction) at 0–1 cm for dNBR equal to 416–533, and for fines at 3–6 cm for dNBR equal to 293–416. Significant linear relations with dNBR were present between ρ_b at 0–1 cm, loss on ignition (LOI) at 0–1 cm, gravel fraction at 0–1 cm, and the large organic fraction at 1–3 cm. No thresholds or effects on soil‐hydraulic properties of field‐saturated hydraulic conductivity or sorptivity were observed. These results suggest that ρ_b and LOI at 0–1 cm have residual direct impacts from the wildfire heat impulse. The θ_i threshold is most likely from delayed groundcover/vegetation recovery that increases evaporation at the highest burn severity sites. Gravel and silt + clay thresholds at 0–1 cm at the transition to high burn severity suggest surface gravel lag development from hydraulic erosion. Thresholds in ρ_b from 3 to 6 cm and in silt + clay fraction from 3 to 6 cm appear to be the result of soil variability between sites rather than wildfire impacts. This work suggests that gravel‐rich soils may have increased resilience to sustained surface runoff generation and erosion following wildfire, with implications for assessments of postwildfire hydrologic and erosion recovery potential.     

Examining the physical components of boundary shear stress for water‐worked gravel deposits

It is argued in this commentary that, in order to understand better the physical mechanisms that generate boundary shear stress over water‐worked gravel beds, flow velocity data should be re‐evaluated by spatial averaging the Reynolds equations to produce time‐ and space‐averaged (double‐averaged) momentum equations. A series of laboratory experiments were conducted in which the flow velocities were measured using a PIV system over two water‐worked gravel deposits. Combined with detailed data on the bed surface topography and vertical porosity, the physical components of shear stress were obtained. This enabled the various momentum transfer mechanisms present above, within and at the interface of a porous, fluvial deposit, to be quantified. This included the examination of the relevant contributions of temporal and spatial fluctuations in velocity and surface drag to the overall momentum transfer. It is demonstrated that double‐averaging represents a logical framework for assessing the fluid forces responsible for sediment entrainment and for investigating intragravel flow and sediment–water interface exchange mechanisms within the roughness layer in water‐worked gravel deposits. By considering the physical components of shear stress and their relative sizes it was possible to provide a physically based explanation for existing observations of enhanced mobility of gravel–sand mixtures and the transfer of solutes into porous, gravel deposits. This analysis reveals the importance of obtaining co‐located, high quality spatial data on the flow field and bed surface topography in order to gain a physical understanding of the mechanisms which generate boundary shear stress. Copyright © 2010 John Wiley & Sons, Ltd.     

Increase in coarse sediment transport associated with disturbance of gravel river beds by signal crayfish (Pacifastacus leniusculus)

There is growing acknowledgement of the interaction between animals and the river bed on which they live and the implications of biological activity for geomorphic processes. It has been observed that signal crayfish (Pacifastacus leniusculus) disturb gravel substrates, potentially promoting sediment transport and impacting ecological communities. However, the mechanisms involved and the extent of their impact remain poorly understood, especially in relation to other processes that affect grain mobility in gravel‐bed rivers. A series of flume experiments, using loose and water‐worked gravel beds of narrowly graded grain sizes that were exposed to 6 h of crayfish activity under low‐velocity flows, showed a substantial increase in the number of grains entrained by subsequent higher‐velocity flows when compared with control runs in which crayfish were never introduced. Crayfish alter the topography of their substrate by constructing pits and mounds, which affect grain protrusion. When walking and foraging, they also alter gravel fabric by reorienting and changing the friction angle of surface grains. In water‐worked surfaces, this fabric rearrangement is shown to lead to a statistically significant, partial reversal of the structuring that had been achieved by antecedent flow. For these previously water‐worked surfaces, the increase in entrainment arising from disturbance by crayfish was statistically significant, with grain transport nearly twice as great. This suggests that signal crayfish, an increasingly widespread invasive species in temperate latitudes beyond their native NW North America, have the potential to enhance coarse‐grained bedload flux by altering the surface structure of gravel river beds and reducing the stability of surface grains. This study illustrates further the importance of acknowledging the impact of mobile organisms in conditioning the river bed when assessing sediment entrainment mechanics in the context of predicting bedload flux. Copyright © 2011 John Wiley & Sons, Ltd.     

Bed scour by debris flows: experimental investigation of effects of debris‐flow composition

Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of bed clusters and size gradation on operational time distribution for non‐uniform bed‐load transport

The operational time distribution (OTD) defines the time for bed‐load sediment spent in motion, which is needed to characterize the random nature of sediment transport. This study explores the influence of bed clusters and size gradation on OTD for non‐uniform bed‐loads. First, both static and mobile bed armouring experiments were conducted in laboratorial flumes to monitor the transport of mixed sand/gravel sediments. Only in the mobile armouring experiment did apparent bed clusters develop, because of stable feeding and a longer transport period. Second, a generalized subordinated advection (GSA) model was applied to quantify the observed dynamics of tracer particles. Results show that for the static armour layer (without sediment feed), the best‐fit OTD assigns more weight to the large displacement of small particles, likely because of the size‐selective entrainment process. The capacity coefficient in the GSA model, which affects the width of the OTD, is space dependent only for small particles whose dynamics can be significantly affected by larger particles and whose distribution is more likely to be space dependent in a mixed sand and gravel system. However, the OTD for the mobile armour layer (with sediment recirculation) exhibited longer tails for larger particles. This is because the trailing edge of larger particles is more resistant to erosion, and their leading front may not be easily trapped by self‐organized bed clusters. The strong interaction between particle–bed may cause the capacity coefficient to be space‐dependent for bed‐load transport along mobile armour layers. Therefore, the combined laboratory experiments and stochastic model analysis show that the OTD may be affected more by particle–bed interactions (such as clusters) than by particle–particle interactions (e.g. hiding and exposing), and that the GSA model can quantify mixed‐size sand/gravel transport along river beds within either static or mobile armour layers. Copyright © 2016 John Wiley & Sons, Ltd.     

Detecting significant sediment motion in a laboratory flume using digital video image analysis

A video analysis method for monitoring sediment transport and sorting processes in a laboratory flume is presented. Video taken through the glass side‐wall of a laboratory flume is captured using a digital CCD (charge‐coupled device) camera and significant movements between individual frames are detected using image analysis. This method involves direct subtraction of the brightness numbers of pixels in sequential video frames, followed by thresholding to produce binarized images of significant change, above the inherent level of system noise. Experimental results showing dilation of a gravel framework and rapid infiltration of fines just prior to entrainment are discussed. Copyright © 2000 John Wiley & Sons, Ltd.     

A review of factors influencing the availability of dissolved oxygen to incubating salmonid embryos

Previous investigations into factors influencing incubation success of salmonid progeny have largely been limited to the development of empirical relationships between characteristics of the incubation environment and survival to emergence. It is suggested that adopting a process‐based approach to assessing incubation success aids identification of the precise causes of embryonic mortalities, and provides a robust framework for developing and implementing managerial responses. Identifying oxygen availability within the incubation environment as a limiting factor, a comprehensive review of trends in embryonic respiration, and processes influencing the flux of oxygenated water through gravel riverbeds is provided. The availability of oxygen to incubating salmonid embryos is dependent on the exchange of oxygenated water with the riverbed, and the ability of the riverbed gravel medium to transport this water at a rate and concentration appropriate to support embryonic respiratory requirements. Embryonic respiratory trends indicate that oxygen consumption varies with stage of development, ambient water temperature and oxygen availability. The flux of oxygenated water through the incubation environment is controlled by a complex interaction of intragravel and extragravel processes and factors. The processes driving the exchange of channel water with gravel riverbeds include bed topography, bed permeability, and surface roughness effects. The flux of oxygenated water through riverbed gravels is controlled by gravel permeability, coupling of surface–subsurface flow and oxygen demands imposed by materials infiltrating riverbed gravels. Temporally and spatially variable inputs of groundwater can also influence the oxygen concentration of interstitial water. Copyright © 2006 John Wiley & Sons, Ltd.     

Distribution and species composition of macroinvertebrates in the hyporheic zone of bed sediment

The hyporheic zone is a layer of substrate on a river bed where benthic animals normally live,grow,feed,reproduce,and exist for any portion of their life cycle.The hyporheic zone was studied by samplin...     

Formation and erosion of sediment cover in an experimental bedrock‐alluvial channel

Sediment grains in a bedrock‐alluvial river will be deposited within or adjacent to a sediment patch, or as isolated grains on the bedrock surface. Previous analysis of grain geometry has demonstrated that these arrangements produce significant differences in grain entrainment shear stress. However, this analysis neglected potential interactions between the sediment patches, local hydraulics and grain entrainment. We present a series of flume experiments that measure the influence of sediment patches on grain entrainment. The flume had a planar bed with roughness that was much smaller than the diameters of the mobile grains. In each experiment sediment was added either as individual grains or as a single sediment pulse. Flow was then increased until the sediment was entrained. Analysis of the experiments demonstrates that: (1) for individual grains, coarse grains are entrained at a higher discharge than fine grains; (2) once sediment patches are present, the different in entrainment discharge between coarse and fine grains is greatly reduced; (3) the sheltering effect of patches also increases the entrainment discharge of isolated grains; (4) entire sediment patches break‐up and are eroded quickly, rather than through progressive grain‐by‐grain erosion; (5) as discharge increases there is some tendency for patches to become more elongate and flow‐aligned, and more randomly distributed across the bed. One implication of this research is that the critical shear stress in bedrock‐alluvial channels will be a function of the extent of the sediment cover. Another is that the influence of sediment patches equalizes critical shear stresses between different grain sizes and grain locations, meaning that these factors may not need to be accounted for. Further research is needed to quantify interactions between sediment patches, grain entrainment and local hydraulics on rougher bedrock surfaces, and under different types of sediment supply. Copyright © 2016 John Wiley & Sons, Ltd.     

Quantifying gravel overlap and dislodgement forces on natural river bars: implications for particle entrainment

Equations for predicting particle entrainment typically assume that clast weight is the only factor resisting motion in the force balance on individual grains. In this work, increases in the force required to dislodge surface particles due to overlapping by surrounding clasts is quantified. Field data were collected at two subaerially‐exposed bars along the Colorado River in central Texas, USA, with median gravel diameters (D₅₀) of 37 and 64 mm. Clast size, shape, weight, the force required for vertical removal, and the fraction of clast area covered by surrounding grains were measured. Small hooks were glued to individual clasts without disrupting their positions and quasi‐static peak forces required to vertically dislodge each clast were measured using a force gauge. Clasts were also colored with dye before being dislodged, and image analysis was used to calculate the fraction of clast surface area covered by surrounding grains. The effect of overlap on the particle force balance is quantified by defining the ‘excess force ratio’ as the dislodgement force divided by the weight of the clast. Excess force ratio varies weakly but systematically with clast size: lifting larger clasts can require forces up to two times the clast's weight, while smaller clasts can require forces up to seven times their weight. The fraction of clast surface area covered by surrounding particles is also weakly correlated with excess force ratio. By assuming that critical shear stresses are proportional to the excess force ratio, the effect that overlap alone may have on particle entrainment is calculated. For a given size class, the most mobile grains should have critical shear stresses controlled only by their weight. However, clast overlap also causes broad distributions of critical stresses for partially‐exposed surface grains. The data quantify the significant fraction of bed area that should be less mobile than grain size alone would predict. Copyright © 2011 John Wiley & Sons, Ltd.     

Evolution of an advancing gravel front: observations from Vedder Canal,British Columbia

Channelization of the lowermost part of Vedder River in 1922 initiated a natural experiment relevant to the unresolved question of how abrupt gravel–sand transitions develop along rivers. The new channel (Vedder Canal) had a fine bed and a much lower slope than the gravel‐bed river immediately upstream. Changes in morphology and sedimentology as gravel advanced into and along the Canal are documented using air photos, historical surveys, and fieldwork. The channel aggraded and steepened until stabilized by occasional gravel extraction in recent decades. The deposited material fines progressively along the Canal but the gravel front has retained an abrupt appearance because it has advanced by the sequential development of discrete gravel tops on initially sandy alternate bars. Near the gravel front the bed is highly bimodal and there is a sharper drop in the extent of gravel‐framework surface facies than in bulk gravel content. Ahead of the front, gravel is restricted to thin ribbons which often become buried by migrating sand. Calculations show that even though the gravel bed at the head of the Canal is almost unimodal, size‐selective transport during floods can account for the strong bimodality farther downstream. Copyright © 2011 John Wiley & Sons, Ltd.     

Zircon U–Pb ages of plutonic rocks in the southern Abukuma Mountains: Implications for Cretaceous geotectonic evolution of the Abukuma Belt

Plutonic rocks in the southern Abukuma Mountains include gabbro and diorite, fine‐grained diorite, hornblende–biotite granodiorite (Ishikawa, Samegawa, main part of Miyamoto and Tabito, Kamikimita and Irishiken Plutons), biotite granodiorite (the main part of Hanawa Pluton and the Torisone Pluton), medium‐ to coarse‐grained biotite granodiorite and leucogranite, based on the lithologies and geological relations. Zircon U–Pb ages of gabbroic rocks are 112.4 ±1.0 Ma (hornblende gabbro, Miyamoto Pluton), 109.0 ±1.1 Ma (hornblende gabbro, the Hanawa Pluton), 102.7 ±0.8 Ma (gabbronorite, Tabito Pluton) and 101.0 ±0.6 Ma (fine‐grained diorite). As for the hornblende–biotite granodiorite, zircon U–Pb ages are 104.2 ±0.7 Ma (Ishikawa Pluton), 112.6 ±1.0 Ma (Tabito Pluton), 105.2 ±0.8 Ma (Kamikimita Pluton) and 105.3±0.8 Ma (Irishiken Pluton). Also for the medium‐ to fine‐grained biotite granodiorite, zircon U–Pb ages are 106.5±0.9 Ma (Miyamoto Pluton), 105.1 ±1.0 Ma (Hanawa Pluton) and the medium‐ to coarse‐grained biotite granodiorite has zircon U–Pb age of 104.5 ±0.8 Ma. In the case of the leucogranite, U–Pb age of zircon is 100.6 ±0.9 Ma. These data indicate that the intrusion ages of gabbroic rocks and surrounding granitic rocks ranges from 113 to 101 Ma. Furthermore, K–Ar ages of biotite and or hornblende in the same rock samples were dated. Accordingly, it is clear that these rocks cooled down rapidly to 300 °C (Ar blocking temperature of biotite for K–Ar system) after their intrusion. These chronological data suggest that the Abukuma plutonic rocks in the southern Abukuma Mountains region uplifted rapidly around 107 to 100 Ma after their intrusion.     

Effect of changes in fine‐grained matrix on bedload sediment transport in a gravel‐bed river

While clay and silt matrices of gravel‐bed rivers have received attention from ecologists concerned variously with the deteriorating environments of benthic and hyporheic organisms, their impact on sediment entrainment and transport has been explored less. A recent increase of such a matrix in the bed of Nahal Eshtemoa, an ephemeral river of the northern Negev, has more than doubled the boundary shear stress needed to initiate bedload, from 7 N m^‐2 (τ^* = 0.027) during the flash floods of 1991–2001 to 15 N m^‐2 (τ^* = 0.059) during those of 2008–2009. The relation between bedload flux and boundary shear stress continues to be well‐defined, but it is displaced. The matrix now contains a significant amount of silt and clay size material. The reasons for the increased entrainment threshold of bedload are explored. Large‐scale laser scanning of the dry bed reveals a reduction in grain‐scale morphological roughness, while artificial in situ tests of matrix integrity indicate considerable cohesion. The implications for adopting bed material sampling strategies that account for matrix development are assessed. Copyright © 2012 John Wiley & Sons, Ltd.     

Flow modelling in gravel‐bed rivers: rethinking the bottom boundary condition

A key problem in computational fluid dynamics (CFD) modelling of gravel‐bed rivers is the representation of multi‐scale roughness, which spans the range from grain size, through bedforms, to channel topography. These different elements of roughness do not clearly map onto a model mesh and use of simple grain‐scale roughness parameters may create numerical problems. This paper presents CFD simulations for three cases: a plane bed of fine gravel, a plane bed of fine gravel including large, widely‐spaced pebble clusters, and a plane gravel bed with smaller, more frequent, protruding elements. The plane bed of fine gravel is modelled using the conventional wall function approach. The plane bed of fine gravel including large, widely‐spaced pebble clusters is modelled using the wall function coupled with an explicit high‐resolution topographic representation of the pebble clusters. In these cases, the three‐dimensional Reynolds‐averaged continuity and Navier–Stokes equations are solved using the standard k ? ε turbulence model, and model performance is assessed by comparing predicted results with experimental data. For gravel‐bed rivers in the field, it is generally impractical to map the bed topography in sufficient detail to enable the use of an explicit high‐resolution topography. Accordingly, an alternative model based on double‐averaging is developed. Here, the flow calculations are performed by solving the three‐dimensional double‐averaged continuity and Navier‐Stokes equations with the spatially‐averaged 〈k ? ε〉 turbulence model. For the plane bed of fine gravel including large, widely‐spaced pebble clusters, the model performance is assessed by comparing the spatially‐averaged velocity with the experimental data. The case of a plane gravel bed with smaller, more frequent, protruding elements is represented by a series of idealized hypothetical cases. Here, the spatially‐averaged velocity and eddy viscosity are used to investigate the applicability of the model, compared with using the explicit high‐resolution topography. The results show the ability of the model to capture the spatially‐averaged flow field and, thus, illustrate its potential for representing flow processes in natural gravel‐bed rivers. Finally, practical data requirements for implementing such a model for a field example are given. Copyright © 2011 John Wiley & Sons, Ltd.