Coring tips

This commentary is intended as a practical guide for the non-motorized use of piston corers to obtain undisturbed sections of lake sediments. Good recovery is essential for accurate reconstruction of environmental and limnological history. Emphasis is placed on the square-rod piston corer, which is widely used for acquisition of sediment cores in meter-long sections from lakes as much as 30 m deep. Coring platforms for open water can be easily prepared on pairs of boats or canoes or (in water depth up to 15 m) even a single small rubber raft, but firm anchoring is essenial to maintain the vertical position of the casing and to assure re-entry into a single hole. Incomplete recovery on individual drives is not a result of sediment compaction but rather the build-up of friction on the tube interior, by which the core forms a plug that prevents further recovery.Short cores of soft sediment for the study of recent changes in lakes are also best acquired with a piston corer, for a gravity corer without a piston may be subject to the same type of plug formation. In cases in which the structure of the sediment must be preserved (e.g. annual laminations), freezing the sediment in place with a dry-ice solution is the best procedure.     

Coring and extruding sediments from shall lakes with the simple, inexpensive VolksCorer and VolksExtruder

Materials for constructing a simple piston corer are available at most well-stocked hardware stores, primarily using galvanized fence post for the barrel, and pipe for the drive rod and head. These are assembled with a modicum of machinist skills. In the field, this VolksCorer operates like similar corers; it is limited to relatively shallow water (about 10–15 m) and is poorly suited for down-the-hole coring, but it requires few specialized tools. Likewise, materials to construct the VolksExtruder are widely available; this extruder, although simple, allows very precise extrusion control. The very low cost of the corer and extruder (less than US$50 each) make them suitable for investigators operating with low budgets without sacrificing sample quality.     

Freeze coring soft sediments in tropical lakes

A new freeze corer is described that is specifically designed for operation in warm tropical lakes. It combines the standard wedge-shaped freeze-on container with a 20-liter thermos from which pellets of solid CO₂ descend into the wedge to replace those that have sublimated. This extends the duration of effective freezing from ~20 to ~45 min, sufficient to form an adequate thickness of frozen crust in warm (> 22 °C) lakes and prevent its premature melting during retrieval through the water column. The instrument contains no electrical components, which simplifies construction, operation, and maintenance. The front and back surfaces of the freeze wedge are fitted length-wise with serrated ridges to facilitate removal of the crust as four rectangular sediment slabs. The feasibility of freeze coring studies in tropical regions is mainly determined by the local availability of a large-volume dry ice producer.     

Diatom-based interpretation of sediment banding in an urbanized lake

Sediment stratigraphy and diatom succession were studied in an 80.5-cm core taken from the deepest part of Third Sister Lake, a small kettle hole in a recently urbanized landscape of southeastern Michigan. Alternating light clay and dark organic bands documented sporadic inputs of clay from outside the basin during rain events, rather than annual laminations. Urban construction activity also disrupted the inflow stream bed and facilitated transport of clay into the lake to generate non-rhythmic banding in the lake's deep hole. Diatom analysis revealed dramatic changes in predominant taxa with sediment depth verifying the non-annual nature of the sediment bands. Observation of halophilic diatom taxa also documented effects of human activity such as road salting on this small, urban lake.     

Records of aquatic pollen and sediment properties as indicators of late-Quaternary Alaskan lake levels

We investigated whether techniques developed to evaluate qualitative lake-level changes in the temperate zone can be used in sub-arctic and arctic Alaska. We focused on aquatic pollen records and sediment properties (loss-on-ignition and magnetic susceptibility) from centrally-located sediment-surface samples and cores, as these are the most commonly reported data in the literature. Modern aquatic pollen values are generally low (< 5%) and may be zero, even in lakes with abundant aquatic macrophytes. Greater diversity and higher values of aquatic pollen are likely at depths < 5 m, but pollen is found in depths up to 15 m. It is absent at depths > 20 m. Spores of Isoetes and Equisetum and Pediastrum cell-nets, when present, tend to be widely distributed, even in deep water. At Birch Lake, interior Alaska, trends in aquatic taxa and sediment characteristics for the last ca. 12,000 ¹⁴C yrs recorded in a single, deep-water core reflect the same water-level changes as do transect-based lake-level reconstructions - if modern distributional characteristics of pollen and spores are taken into account. The lake rose from extremely low levels at ca. 12,000 ¹⁴C yr B.P. After a period of fluctuation, it rose to a relatively high level by ca. 8000 ¹⁴C yr B.P. and then stabilized. A preliminary survey of aquatic pollen trends from other lake-sediment records suggests that the period ca. 11,000-8000 ¹⁴C yr B.P. may have seen relatively low lake levels in north-western and interior Alaska and high levels thereafter. Changes in aquatic pollen and sediments are evident in north-eastern interior lakes at the same time, but they are more difficult to interpret. Aquatic pollen productivity in Alaskan lakes may partly depend on factors other than water depth (e.g. temperature, pH, nutrient status, or length of the ice-free season). An Alaska-wide reconstruction of late-Quaternary lake levels based on extant single-core data would be best done after further study of contributing factors that may control sediment properties and aquatic pollen distribution.     

Recent lake level variations in Lake Haubi, central Tanzania, interpreted from pollen and sediment studies

Variations in pollen assemblages and in physical and chemical composition of a dated sediment record from the small Lake Haubi in north central Tanzania, reveal lake level fluctuations since the late 19th century. Lake Haubi changed from a seasonally inundated swamp to a lake in the beginning of the 20th century. With the exception of 1942-44, when it dried out completely, it remained water filled until 1994 when it again turned into a swamp. The lake level fluctuations in Lake Haubi are largely in phase with fluctuations of the larger East African lakes levels during the 20th century, and are therefore interpreted as being mainly controlled by regional climatic fluctuations. However, the initial formation of Lake Haubi at the turn of the century was likely due to local catchment specific causes, e.g. changes in land use, as the rapid increase in the water level at this time does not correspond to other lake level records from the region.     

Suspended sediment transport and deposition in a high arctic meromictic lake

A study of sedimentary processes and sediment yields in a high arctic meromictic lake (Lake C2, Taconite Inlet, Northern Ellesemere Island, Canada) was undertaken from May 1990 through August 1992 to understand the links between climatic controls, hydrology, and the laminated sediment record preserved in the lake. Understanding the relationships between processes and the sediment record is critical for interpreting the climatic significance of the laminated sediments in a region where high resolution climate proxy records are quite limited.Sediment transport to Lake C2 is dominated by fluvial processes. During the early part of the melt season slushflows transport sediment to the lake surface. Subsequently, suspended sediment is delivered to the lake by the main inlet stream and distributed lakeward by a plume emanating the main inlet channel. Due to the strong density stratification of the water column the plume distributes sediment downlake by overflows and interflows in the epilimnion. In general, overflows are generated by lower discharge events whereas interflows penetrate to the halocline during high discharge with increased suspended sediment concentration.Sediment trap analysis demonstrates that suspended sediment transport and deposition responds to diurnal through annual changes in stream discharge. Seasonal and annual sediment trap yields agree with average accumulation rates determined from varve thickness measurements and cumulative suspended sediment discharge from the main inlet stream indicating a close link between climatological, hydrological, and sedimentological controls and varve deposition.This is the fourth in a series of papers published in this issue on the Taconite Inlet Lakes Project. These papers were collected by Dr R. S. Bradley.     

Spatial uniformity of sediment accumulation in varved lake sediments in northern Sweden

As part of an investigation aimed at assessing the potential of northern Swedish varved lake sediments for fine-resolution reconstruction of past climatic conditions, the following questions were addressed; how representative is a single core, does the appearance of varves change as the sediment ages, and how can varve thickness and within-varve structures be digitized? Analyses of replicate cores from Kassjön, using sample sequences of seasonal, annual and centennial time resolution, show that spatial variability of sediment accumulation in the varved sediment is very low. Comparisons of intensity curves from image analysis of freeze cores of recent sediments from Lake Nylandssjön, sampled in 1980 and 1985, indicate that the varves acquire their appearance at the sediment-water interface during sedimentation and that the varve structures are preserved during diagenetic processes. Measurement of varve thicknesses with a tree-ring microscope and with image analysis gave similar results. However, with image analysis, within-varve structures such as colour variations and thicknesses of seasonal layers, can also be recorded, increasing the possibilities for palaeolimnological and palaeoclimatic inferences.     

Long cores from small lakes—recovering up to 100 m-long lake sediment sequences with a high-precision rod-operated piston corer (Usinger-corer)

We present a unique, versatile piston corer for recovering continuous lake and bog sediment sequences with superior accuracy and quality. The main components of the system and their function are described, with special focus on measures for obtaining long, continuous lake sediment sections up to a current maximum length of 95 m. Examples of lake sediment profiles obtained with this system from different climatic zones are presented.     

Progress in isotope paleohydrology using lake sediment cellulose

Recent advances in sample preparation techniques and mass spectrometry have fostered more routine oxygen isotope analysis of aquatic cellulose in lake sediment cores, a proxy for lake water oxygen isotope history. These methodological developments have significantly increased the feasibility of incorporating this approach into high-resolution, multi-site, and multi-proxy studies, which are frequently necessary to answer complex hydrological, hydroecological and hydroclimatic questions requiring a paleoenvironmental perspective. Direct translation of lake sediment aquatic cellulose oxygen isotope composition into lake water oxygen isotope composition offers appreciable opportunity for quantitative paleohydrological reconstructions, as evidenced by studies conducted over the past 15 years that span Holocene and pre-historical timescales.     

Stratigraphy of total metals in PIRLA sediment cores

Sediment cores from 30 low-alkalinity lakes in northern New England (NE), New York (NY), the northern Great Lakes States (NGLS) of Minnesota, Michigan, and Wisconsin, and Florida (FL) have been dated by ²¹⁰Pb and analyzed for water and organic content, eight major elements (Al, Ti, Fe, Mn, Ca, Mg, Na, K) plus four trace metals (Pb, Zn, Cu, and V). Variations in the percentages of major elements through time are dominated by long-term independent variations in the abundance of SiO₂, FeO, and to a lesser extent Ca and Al. Additional variations are caused by varying proportions of inorganic matter. Major variations in chemistry are generally unrelated to documented distrubances in the watersheds; most disturbances are minor fires or selective logging.Accelerated accumulation of Pb from atmospheric sources into sediment first occurs in sediment dated between 1800 and 1850 in NY and NE, slightly later in the NGLS region, and about 1900 in FL. Modern accumulation rates in all areas are comparable (ca. 1 to 4 g cm^–2 yr^–1). Accumulation rates of Pb in some lakes have declined significantly from 1975 to 1985. Atmospheric deposition of anthropogenic Zn and Cu is also indicated by generally increasing accumulation rates in sediment cores, but the record is not as clear nor are chemical profiles in all lakes parallel to the trends in atmospheric emissions inferred on the basis of fossil fuel consumption, smelting, and other industrial activities. Inter-lake variations in profiles of Cu and Zn are large. Vanadium accumulation rates increase by the 1940s in NY and NE, but not until the 1950s in the NGLS region. This timing correlates with regional trends in the combustion of fuel oil, a major source of atmospheric V.Acidification of some of the lakes is suggested by decreases in the concentration and accumulation rates of Mn, Ca, and Zn in recent sediment, relative to other elements of catchment origin. The decreases generally occur slightly before the onset of acidification as indicated by diatoms. Increased sediment accumulation rates for Fe may indicate the acidification of watershed soils. The use of the accumulation rate of TiO₂ as an indicator of rates of erosion and for normalization of trace metal accumulation rates is in question for lakes where the flux of TiO₂ from the atmosphere varies and is a significant fraction of the total flux of TiO₂ to the sediment.This is the thirteenth of a series of papers to be published by this journal which is a contribution of the Paleoecological Investigation of Recent Lake Acidification (PIRLA) project. Drs. D. F. Charles and D. R. Whitehead are guest editors for this series.     

The landscape factor in the formation of pollen records in lake sediments

Comprehensive paleobotanical and geochemical methods have been used to study the relationship between the spatial scale of landscape development and values of pollen influx to take the bog sediments. The spatial-temporal history of the four lakes and a bog was established in NE Estonia and pollen analyses of thier sediment were made. It was found that the influx of total arboreal pollen directly corresponds with the sizes of the sites studied, and varies with thier expansion or reduction.     

Field calibration and performance of sediment traps in a eutrophic holomictic lake

In wind-stressed and unstratified Lough Neagh low aspect ratio sediment traps, which allow for internal resuspension, collected sediment at a rate close to the natural sediment accumulation rate inferred from dated sediment cores. High aspect ratio traps grossly overestimated the natural rate of sediment accumulation as did, but to a lesser extent, burial rate measurements on an artificial stratigraphic marker. The former type of trap deployed over long exposure periods is therefore recommended as providing the best estimate of net downward particle flux in lakes such as Lough Neagh. However, it is emphasized that all sediment trap types, when operated in shallow turbulent lakes, will to a greater or lesser extent be contaminated by secondary or redeposited material and so will not provide a direct measure of primary sedimentation. Use of tube traps in lakes such as Lough Neagh should not, however, be discounted since they can provide a record of the quality of sedimenting material through time.     

冰湖的界定与分类体系——面向冰湖编目和冰湖灾害研究

冰川湖泊（简称冰湖）不仅是高山区重要的水资源,而且是许多冰川灾害的孕育者和发源地,在冰冻圈科学、气候变化和山地灾害研究中具有重要地位。本文系统讨论了现有冰湖定义及存在的问题,从冰湖编目和冰湖灾害研究视角提出冰湖的定义,指出现有冰湖研究主要是基于“以现代冰川融水为主要补给源或在冰碛垄洼地内积水形成的天然水体”这一冰湖定义的。同时,从冰湖形成机理、地貌形态和空间分布位置将冰湖划分为冰川侵蚀湖（冰斗湖、冰川槽谷湖和其他冰川侵蚀湖）、冰碛阻塞湖（终碛阻塞湖、侧碛阻塞湖、冰碛垄热融湖）、冰川阻塞湖（冰川前进阻塞湖和其他冰川阻塞湖）、冰面湖、冰下（内）湖和其他冰川湖6大类及8个亚类,并给出各冰湖类型相应的遥感判识指标和定量指标,以期建立具有普适性和可操作性的冰湖分类体系。     

Definition and classification system of glacial lake for inventory and hazards study

Glacial lakes are not only the important refresh water resources in alpine region, but also act as a trigger of many glacial hazards such as glacial lake outburst flood (GLOF) and debris flow. Therefore, glacial lakes play an important role on the cryosphere, climate change and alpine hazards. In this paper, the issues of glacial lake were systematically discussed, then from the view of glacial lake inventory and glacial lake hazards study, the glacial lake was defined as natural water mainly supplied by modern glacial meltwater or formed in glacier moraine’s depression. Furthermore, a complete classification system of glacial lake was proposed based on its formation mechanism, topographic feature and geographical position. Glacial lakes were classified as 6 classes and 8 subclasses, i.e., glacial erosion lake (including cirque lake, glacial valley lake and other glacial erosion lake), moraine-dammed lake (including end moraine-dammed lake, lateral moraine-dammed lake and moraine thaw lake), ice-blocked lake (including advancing glacier-blocked lake and other glacier-blocked lake), supraglacial lake, subglacial lake and other glacial lake. Meanwhile, some corresponding features exhibiting on remote sensing image and quantitative indices for identifying different glacial lake types were proposed in order to build a universal and operational classification system of glacial lake.