Using a fluctuating tracer to estimate hyporheic exchange in restored and unrestored reaches of the Truckee River,Nevada, USA

The goal of this research was to compare hyporheic activity in recently restored and adjacent un‐restored reaches of the Truckee River downstream from the Reno/Sparks metropolitan area. The installation of rocky riffles and raised channel bed elevations in the restored reaches may have increased the degree of surface–subsurface interaction. A fluctuating chloride concentration signal served as the tracer, induced by the variable influx of higher salinity water several miles upstream from the study reach. The solute transport model, OTIS, was used in conjunction with the hydrodynamic model, DYNHYD5, to estimate transient storage parameters under unsteady flow conditions. The model was calibrated to chloride concentrations measured over a period of three days at six in‐stream locations representing restored and un‐restored reaches. An automated parameter estimation algorithm (SCE‐UA) was used to optimize parameters for multiple reaches simultaneously and generate a distribution of parameter estimates. Results suggest that the transient storage zone cross‐sectional area (A_s) is larger in the restored reaches than in the unrestored reaches, but the exchange coefficient (α) is smaller, leading to increased hyporheic residence time and hydrologic retention in the vicinity of channel reconstructions. Scenarios were used to simulate the potential effects of increased subsurface residence time on denitrification and in‐stream NO₃‐N concentrations. Monte Carlo analysis was performed to assess uncertainty in the simulation results and show the potential for greater nutrient retention in the lower Truckee River as a result of channel restoration. Copyright © 2009 John Wiley & Sons, Ltd.     

Field studies on factors affecting very fine and ultra fine particulate organic matter deposition in low‐gradient sand‐bed streams

The knowledge on particle deposition in streams is mainly based on investigations in mountain streams. No data exist from low‐gradient sand‐bed streams that largely differ in the morphological and hydraulic factors proposed to affect deposition. To identify physical control on particle deposition in low‐gradient streams, we assessed deposition of very fine and ultra fine organic particulate matter in 18 sand‐bed stream reaches. We added particles derived from lake sediment and assessed the mean transport distance S_P and the deposition velocity v_dep. Additionally, reach hydraulics were estimated by injections of a conservative solute tracer (NaCl). Among the low‐gradient streams, particle deposition kinetics were variable but similar to deposition in mountain streams. S_P was solely related to the flow velocity. This relation was confirmed when comprising published data on deposition of fine organic particles. An association between particle deposition and transient storage factors was insignificant. We found significance of the transient storage to S_P only for repeated measures within a single reach, when flow velocity and benthic conditions were nearly constant. Measured v_dep/v_fall ratios were much larger than unity in most reaches. Evidence from this relation suggests that the vertical transport of very fine and ultra fine organic particulate matter through the water column was caused mainly by vertical mixing. Copyright © 2006 John Wiley & Sons, Ltd.     

Bedload tracing in a high‐sediment‐load mountain stream

This paper reports a radiofrequency identification (RFID) tracing experiment implemented in a high‐sediment‐load mountain stream typical of alpine gravel‐bed torrents. The study site is the Bouinenc Torrent, a tributary to the Bléone River in southeast France that drains a 38·9‐km² degraded catchment. In spring 2008, we deployed 451 tracers with b‐axis ranging from 23 to 520 mm. Tracers were seeded along eight cross‐sections located in the upstream part of the lowest 2·3 km of the stream. Three tracer inventories were implemented in July 2008, 2009 and 2010. Recovery rates calculated for mobile tracers declined from 78% in 2008 to 45% in 2009 and 25% in 2010. Observations of tracer displacement revealed very high sediment dispersion, with frontrunners having travelled more than 2 km only three months after their deployment. The declining recovery rate over time was interpreted as resulting from rapid dispersion rather than deep burial. We evaluated that 64% of the tracers deployed in the active channel were exported from the 2·3‐km study reach three years after the onset of the tracing experiment. Travel distances were characterized by right‐skewed and heavy‐tailed distributions, correctly fitted by a power‐law function. This supports the idea that in gravel‐bed rivers with abundant sediment supply relative to transport capacity, bedload transport can be viewed as a superdiffusive sediment dispersion process. It is also shown that tracers initially deployed in the low‐flow channel were characterized by a 15‐ to 30‐fold increase of mobility compared to tracers deployed in gravel bars. Copyright © 2011 John Wiley & Sons, Ltd.     

The role of vegetation in the retention of fine sediment and associated metal contaminants in London's rivers

Many urban rivers receive significant inputs of metal‐contaminated sediments from their catchments. Restoration of urban rivers often creates increased slack water areas and in‐channel vegetation growth where these metal‐contaminated sediments may accumulate. Quantifying the accumulation and retention of these sediments by in‐channel vegetation in urban rivers is of importance in terms of the planning and management of urban river restoration schemes and compliance with the Water Framework Directive. This paper investigates sediment properties at four sites across three rivers within Greater London to assess the degree to which contaminated sediments are being retained. Within paired restored and unrestored reaches at each site, four different bed sediment patch types (exposed unvegetated gravel, sand, and silt/clay (termed ‘fine’) sediments, and in‐channel vegetated sediments) were sampled and analysed for a range of metals and sediment characteristics. Many samples were found to exceed Environment Agency guidelines for copper (Cu), lead (Pb) and zinc (Zn) and Dutch Intervention Values for Cu and Zn. At all sites, sediments accumulating around in‐channel vegetation were similar in calibre and composition to exposed unvegetated fine sediments. Both bed sediment types contained high concentrations of pseudo‐total and acetic acid extractable metal concentrations, potentially due to elevated organic matter and silt/clay content, as these are important sorbtion phases for metals. This implies that the changed sediment supply and hydraulic conditions associated with river restoration may lead to enhanced retention of contaminated fine sediments, particularly around emergent plants, frequently leading to the development of submerged and emergent landforms and potential river channel adjustments. High pseudo‐total metal concentrations were also found in gravel bed sediments, probably associated with iron (Fe) and manganese (Mn) oxyhydroxides and discrete anthropogenic metal‐rich particles. These results highlight the importance of understanding the potential effects of urban river restoration upon sediment availability and channel hydraulics and consequent impacts upon sediment contaminant dynamics and storage. Copyright © 2014 John Wiley & Sons, Ltd.     

Reintroduced large wood modifies fine sediment transport and storage in a lowland river channel

This paper explores changes in suspended sediment transport and fine sediment storage at the reach and patch scale associated with the reintroduction of partial large wood (LW) jams in an artificially over‐widened lowland river. The field site incorporates two adjacent reaches: a downstream section where LW jams were reintroduced in 2010 and a reach immediately upstream where no LW was introduced. LW pieces were organized into ‘partial’ jams incorporating several ‘key pieces’ which were later colonized by substantial stands of aquatic and wetland plants. Reach‐scale suspended sediment transport was investigated using arrays of time‐integrated suspended sediment samplers. Patch‐scale suspended sediment transport was explored experimentally using turbidity sensors to track the magnitude and velocity of artificially generated sediment plumes. Fine sediment storage was quantified at both reach and patch scales by repeat surveys of fine sediment depth. The results show that partial LW jams influence fine sediment dynamics at both the patch and reach scale. At the patch‐scale, introduction of LW led to a reduction in the concentration and increase in the time lag of released sediment plumes within the LW, indicating increased diffusion of plumes. This contrasted with higher concentrations and lower time lags in areas adjacent to the LW; indicating more effective advection processes. This led to increased fine sediment storage within the LW compared with areas adjacent to the LW. At the reach‐scale there was a greater increase in fine sediment storage through time within the restored reach relative to the unrestored reach, although the changes in sediment transport responsible for this were not evident from time‐integrated suspended sediment data. The results of the study have been used to develop a conceptual model which may inform restoration design. Copyright © 2017 John Wiley & Sons, Ltd.     

The role of channel morphology on the mobility and dispersion of bed sediment in a small gravel‐bed stream

This study uses a unique 10‐year tracer dataset from a small gravel‐bed stream to examine bed mobility and sediment dispersion over long timescales and at a range of spatial scales. Seasonal tracer data that captured multiple mobilizing events was examined, while the effects of morphology on bed mobility and sediment dispersion were captured at three spatial scales: within morphological units (unit scale), between morphological units (reach scale) and between reaches with different channel morphologies (channel scale). This was achieved by analyzing both reach‐average mobility and travel distance data, as well as the development of ‘mobility maps’ that capture the spatial variability in tracer mobility within the channel. The tracer data suggest that sediment transport in East Creek remains near critical the majority of the time, with only rare large events resulting in high mobility rates and grain travel distances large enough to move sediment past dominant bedforms. While a variable capturing both the magnitude and frequency of flow events within a season yielded a better predictor to sediment mobility and dispersion than peak discharge alone, the distribution of events of different magnitude within the season played a large role in determining tracer mobility rates and travel distances. The effects of morphology differed depending on the analysis scale, demonstrating the importance of scale, and therefore study design, when examining the effect of morphology on sediment transport. Copyright © 2016 John Wiley & Sons, Ltd.     

Joint isotopic mass balance: a novel approach to quantifying channel bed to channel margins sediment transfer during storm events

The important role of floodplains and the broader riparian zone in providing temporary storage for a large fraction of the annual sediment load of rivers is well established, but this understanding is largely based on observations of the long‐term average behavior of the catchment. Here we combine measurements of the fallout radionuclides ⁷Be and ²¹⁰Pb and the stable isotopes of hydrogen in water to quantify fine sediment mobilization and storage in a stream and its channel margins during individual intermediate‐sized storm events with recurrence intervals of a few months or less. We demonstrate this method using five storm events in a small (~15 km²), undeveloped, gravel‐bedded tributary of the Connecticut River (USA). We estimate that in each storm, the mass of sediment deposited onto the margins accounts for almost 90% of the sediment mobilized from the bed, with the remainder of the mobilized bed sediment transported downstream as suspended load. The result that the bed is a net source of sediment to the stream and the margins a net sink is robust, but estimates of the mass of material eroded from the bed and deposited on the margins are less certain. The source of sediment to the bed remains unclear as, consistent with earlier studies, we observe only limited deposition of sediment to the bed during the storm events. The suspended sediment is organic‐rich and thus its source may be associated with in‐channel organic decay between storm events. Understanding the coupled interactions between discharge magnitude and frequency and sediment resupply at the event time scale has important implications for stream restoration efforts seeking to connect the channel and the broader riparian zone, and for the development of accurate sediment budgets and predictions of sediment flux from a watershed. Copyright © 2015 John Wiley & Sons, Ltd.     

Relation between flow,surface‐layer armoring and sediment transport in gravel‐bed rivers

This study investigates trends in bed surface and substrate grain sizes in relation to reach‐scale hydraulics using data from more than 100 gravel‐bed stream reaches in Colorado and Utah. Collocated measurements of surface and substrate sediment, bankfull channel geometry and channel slope are used to examine relations between reach‐average shear stress and bed sediment grain size. Slopes at the study sites range from 0·0003 to 0·07; bankfull depths range from 0·2 to 5 m and bankfull widths range from 2 to 200 m. The data show that there is much less variation in the median grain size of the substrate, D_50s, than there is in the median grain size of the surface, D₅₀; the ratio of D₅₀ to D_50s thus decreases from about four in headwater reaches with high shear stress to less than two in downstream reaches with low shear stress. Similar trends are observed in an independent data set obtained from measurements in gravel‐bed streams in Idaho. A conceptual quantitative model is developed on the basis of these observations to track differences in bed load transport through an idealized stream system. The results of the transport model suggest that downstream trends in total bed load flux may vary appreciably, depending on the assumed relation between surface and substrate grain sizes. Copyright © 2007 John Wiley & Sons, Ltd.     

Impact of debris dams on hyporheic interaction along a semi‐arid stream

Hyporheic exchange increases the potential for solute retention in streams by slowing downstream transport and increasing solute contact with the substrate. Hyporheic exchange may be a major mechanism to remove nutrients in semi‐arid watersheds, where livestock have damaged stream riparian zones and contributed nutrients to stream channels. Debris dams, such as beaver dams and anthropogenic log dams, may increase hyporheic interactions by slowing stream water velocity, increasing flow complexity and diverting water to the subsurface. Here, we report the results of chloride tracer injection experiments done to evaluate hyporheic interaction along a 320 m reach of Red Canyon Creek, a second order stream in the semi‐arid Wind River Range of Wyoming. The study site is part of a rangeland watershed managed by The Nature Conservancy of Wyoming, and used as a hydrologic field site by the University of Missouri Branson Geologic Field Station. The creek reach we investigated has debris dams and tight meanders that hypothetically should enhance hyporheic interaction. Breakthrough curves of chloride measured during the field experiment were modelled with OTIS‐P, a one‐dimensional, surface‐water, solute‐transport model from which we extracted the storage exchange rate α and cross‐sectional area of the storage zone A_s for hyporheic exchange. Along gaining reaches of the stream reach, short‐term hyporheic interactions associated with debris dams were comparable to those associated with severe meanders. In contrast, along the non‐gaining reach, stream water was diverted to the subsurface by debris dams and captured by large‐scale near‐stream flow paths. Overall, hyporheic exchange rates along Red Canyon Creek during snowmelt recession equal or exceed exchange rates observed during baseflow at other streams. Copyright © 2005 John Wiley & Sons, Ltd.     

Effects of sediment pulses on bed relief in bar‐pool channels

To further develop prediction of the range of morphological adjustments associated with sediment pulses in bar‐pool channels, we analyze channel bed topographic data collected prior to and following the removal of two dams in Oregon: Marmot Dam on the Sandy River and Brownsville Dam on the Calapooia River. We hypothesize that, in gravel‐bed, bar‐pool channels, the response of bed relief to sand and gravel sediment pulses is a function of initial relief and pulse magnitude. Modest increases in sediment supply to initially low‐relief, sediment‐poor cross‐sections will increase bed relief and variance of bed relief via bar deposition. Modest increases in sediment supply to initially high‐relief cross‐sections, characteristic of alternate bar morphology, will result in decreased bed relief and variance of relief via deposition in bar‐adjacent pools. These hypothesized adjustments are measured in terms of bed relief, which we define as the difference in elevation between the pool‐bottom and bar‐top. We evaluate how relief varies with sediment thickness, where both relief and mean sediment thickness at a cross‐section are normalized by the 90th percentile of observed relief values within a reach prior to a sediment pulse. Field measurements generally supported the stated hypotheses, demonstrating how introduction of a sediment pulse to low‐relief reaches can increase mean and variance of relief, while introduction to high‐relief reaches can decrease the mean and variance of bed relief, at least temporarily. In general, at both sites, the degree of impact increased with the thickness of sediment delivered to the cross‐section. Results thus suggest that the analysis is a useful step for understanding the morphological effects of sediment pulses introduced to gravel‐bed, bar‐pool channels. Copyright © 2015 John Wiley & Sons, Ltd.     

The effect of transient storage on nitrate uptake lengths in streams: an inter‐site comparison

Surface water–groundwater interaction in the hyporheic zone may enhance biogeochemical cycling in streams, and it has been hypothesized that streams exchanging more water with the hyporheic zone should have more rapid nitrate utilization. We used simultaneous conservative solute and nitrate addition tracer tests to measure transient storage (which includes hyporheic exchange and in‐stream storage) and the rate of nitrate uptake along three reaches within the Red Canyon Creek watershed, Wyoming. We calibrated a one‐dimensional transport model, incorporating transient storage (OTIS‐P), to the conservative solute breakthrough curves and used the results to determine the degree of transient storage in each reach. The nitrate uptake length was quantified from the exponential decrease in nitrate concentration with distance during the tracer tests. Nitrate uptake along the most downstream reach of Red Canyon Creek was rapid (turnover time K^?1_c = 32 min), compared with nitrate uptake reported in other studies (K^?1_c = 12 to 551 min), but other sites within the watershed showed little nitrate retention or loss. The uptake length S_w‐NO^?₃ for the most downstream reach was 500 m and the mass transfer coefficient V_f‐NO^?₃ was 6·3 m min^?1. Results from 15 other nitrate‐addition tracer tests were used to create a regression model relating transient storage and measures of stream flow to nitrate uptake length. The model, which includes specific discharge and transient storage area, explains almost half the variability in nitrate uptake length (adjusted R² = 0·44) and is most effective for comparing sites with very different stream characteristics. Although large differences in specific discharge and storage zone area explain inter‐site differences in nitrate uptake, other unmeasured variables, such as available organic carbon and microbial community composition, are likely important for predicting differences in nitrate uptake between sites with similar specific discharge rates and storage zone areas, such as when making intra‐site comparisons. Copyright © 2007 John Wiley & Sons, Ltd.     

Geomorphic response to gravel augmentation and high‐flow dam release in the Trinity River,California

The geomorphic effect of introducing a gravel augmentation totaling 520 m³ into a gravel‐bed stream during a dam‐controlled flood in May of 2015 was monitored with bedload transport measurements, an array of seismometers, and repeated topographic surveys. Half of the augmented gravel was injected into the flow with front‐end loaders on the rising limb of the flood and the other half was injected on the first day of the peak. Virtually all of the gravel transported past the injection point was deposited within about 7 to 10 channel widths of the injection point. Most of the injected gravel deposited along the left bank of the river whereas the right half of the channel bed was dominated by scour. The downstream third of the depositional area consisted of a small dune field that developed prior to the second gravel injection and subsequently migrated about one channel width downstream. A second depositional front was observed upstream from the gravel injection point, where a delta‐like wedge of bed material developed in the first hours of the flow release and changed little over the remainder of the release. These two depositional areas represent small‐scale bed‐material storage reservoirs with the potential to accumulate and periodically release packets of bed material. Interactions with such storage reservoirs are hypothesized to cause large bed‐material pulses to disperse by fragmenting into multiple smaller pulses. As a refinement to the conceptual model that views sediment pulse evolution in terms of dispersion and translation, the concept of pulse fragmentation has practical implications for gravel management. It implies that gravel augmentations can produce morphologic changes at locations that are separated from the augmentation point by arbitrarily long reaches, and it highlights the dependence of pulse propagation rates on the nature and distribution of the bed‐material storage reservoirs in the channel system. Copyright © 2017 John Wiley & Sons, Ltd.     

Downstream fining in contrasting reaches of the sand‐bedded Yellow River

Compared to downstream fining of a gravel‐bedded river, little field evidence exists to support the process of downstream fining in large, fine sand‐bedded rivers. In fact, the typically unimodal bed sediments of these rivers are thought to produce equal mobility of coarse and fine grains that may discourage downstream fining. To investigate this topic, we drilled 200 sediment cores in the channel beds of two fine‐grained sand‐bedded reaches of the Yellow River (a desert reach and a lower reach) and identified a fine surface layer (FSL) developed over a coarse subsurface layer (CSL) in the 3‐m‐thick bed deposits. In both reaches downstream, the thickness of the FSL increased, while that of the CSL decreased. Comparison of the depth‐averaged median grain sizes of the CSL and the FSL separately in both reaches shows a distinct downstream fining dependence to the median grain size, which indicates that at a large scale of 600‐800 km, the CSL shows a significant downstream fining, but the FSL shows no significant trends in downstream variations in grain size. This result shows that fine sediment supply (<0·08 mm median grain size) from upstream, combined with lateral fine sediment inputs from tributaries and bank erosion, can cause a rapid fining of the downstream channel bed surface and can develop the FSL layer. However, in the desert reach, lateral coarse sediment supply (>0·08 mm median grain size) from wind‐borne sediments and cross‐desert tributaries can interrupt the FSL and coarsen the channel bed surface locally. Copyright © 2011 John Wiley & Sons, Ltd.     

The influence of Pacific salmon decay products on near‐field streambed sediment and organic matter dynamics: a flume simulation

Pacific salmon are biogeomorphic agents shown to induce positive feedbacks on their natal watersheds. However, the literature documenting their ecological effects on in‐stream natal environments is more divisive. The disturbance salmon create during redd construction has the potential to reduce stream productivity. The pulse of salmon organic matter (SOM) and marine derived nutrients (MDNs) released during carcass decay has been reported as either stimulating in‐stream productivity or having no local effect. To evaluate the ecological costs and benefits of salmon spawning events, MDN delivery and storage processes need to be identified and quantified. A simulation was conducted in three flow‐through flumes (2 m × 2 m × 30 m) over a 33‐day period (consisting of 15 baseline, four MDN exposure, and 14 post‐exposure days) to assess near‐field sediment and organic matter dynamics during active and post‐spawn simulations. The objective of the study was to measure changes in the amounts and particle sizes of suspended and gravel‐stored fine sediment, in order to elucidate the process and significance of SOM recruitment to the gravel bed via sedimentation. Gravel beds in all flumes were enriched with SOM following treatments but the response was highest in the active spawn simulation. The more effective delivery in the active spawn simulation was attributed to its higher inorganic sediment concentration, which is known to enhance floc formation. Although the active spawn simulation delivered more SOM to the gravel bed, the post‐spawn phase may be equally important to natural streams because its decay phase is longer than the active spawn and consequently can provide SOM to the streambed as long as carcasses remain in‐stream. The delivery, and potential retention, of SOM to spawning streambeds and the intergravel environment may be particularly important for interior streams, which experience low flow conditions during the spawning phase and accordingly have the potential for hyporheic nutrient recruitment and storage. Copyright © 2014 John Wiley & Sons, Ltd.     

Observing lingering hyporheic storage using electrical resistivity: variations around stream restoration structures,Crabby Creek,PA

Time‐lapse geophysical surveys can map lingering hyporheic storage by detecting changes in response to saline tracer. Tracer tests were conducted in Crabby Creek, an urban stream outside Philadelphia, to examine the influence of stream restoration structures and variable sediment thickness. We compared electrical resistivity surveys with extensive well sampling (57 wells) in two 13.5‐m‐long reaches, each with a step drop created by a J‐hook. The two step drops varied in tracer behaviour, based on both the well data and the geophysical data. The well data showed more variation in arrival time where the streambed sediment was thick and was more uniform where sediment was thin. The resistivity in the reach with thin sediment showed lingering tracer in the hyporheic zone both upstream and downstream from the J‐hook. In the second reach where the sediment was thicker, the lingering tracer in the hyporheic zone was more extensive downstream from the J‐hook. The contrasting results between the two reaches from both methods suggested that sediments influenced hyporheic exchange more than the step at this location. Resistivity inversion differed from well data in both reaches in that it showed evidence for tracer after well samples had returned to background, mapping lingering tracer either upstream or downstream of a step. We conclude that resistivity surveys may become an important tool for hyporheic zone characterization because they provide information on the extent of slow moving fluids in the hyporheic zone, which have the potential to enhance chemical reactions. Copyright © 2012 John Wiley & Sons, Ltd.     

Hyporheic and total transient storage in small,sand‐bed streams

Key processes in stream ecosystems are linked to hydraulic retention, which is the departure of stream flow from ideal ‘plug flow’, and reflects fluid movement through surface and hyporheic storage zones. Most existing information about hyporheic exchange is based on flume studies or field measurements in relatively steep streams with beds coarser than sand. Stream tracer studies may be used to quantify overall hydraulic retention, but disaggregation of surface and hyporheic retention remains difficult. A stream tracer approach was used to compute the rates at which stream water is exchanged with water in storage zones (total storage) in short reaches of two small, sand‐bed streams under free and obstructed flow conditions. Tracer curves were fit to the one‐dimensional transport with inflow storage model OTIS‐P. Networks of piezometers were used to measure specific discharge between the stream and the groundwater. In the sand‐bed streams studied, parameters describing total retention were in the upper 50% of data compiled from the literature, most of which represented streams with beds coarser than sand. However, hyporheic storage was an insignificant component of total hydraulic retention, representing only 0·01–0·49% of total exchange, and this fraction did not increase after installation of flow obstructions. Total retention did not vary systematically with bed material size, but increased 50–100% following flow obstruction. Removal of roughness elements, such as large wood and debris dams, is detrimental to processes dependent upon transient storage in small, sand‐bed streams. Copyright © 2007 John Wiley & Sons, Ltd.     

Patterns of sediment slug translation and dispersion following typhoon‐induced disturbance,Oyabu Creek,Kyushu, Japan

A six‐year monitoring programme characterized the migration/dispersion patterns of sediment slugs generated following typhoon‐induced disturbances in 1993 and 1997 along a single‐thread gravel‐bed stream, Oyabu Creek, on Kyushu Island, Japan. This laterally con?ned creek comprises rif?e–pool sequences with intervening bedrock outcrops. The passage of sediment pulses associated with sediment slug processes re?ected, and was controlled by, the rif?e–pool structures which provided channel bed roughness, the volume of sediment stored along valley ?oors, and the distribution of bedrock outcrops. Changes to bed material size following major sediment inputs during the disturbance events also exerted an in?uence on subsequent sediment slug processes. The sequence of rainfall events, together with changes to channel bed structure, induced different phases in the sediment slug processes. The capacity of a reach to store or trap sediment, as recorded by the longitudinal structure of the channel, varied during these differing phases. Copyright © 2004 John Wiley & Sons, Ltd.     

Evolution of gravel surfaces in a sediment‐recirculating flume

The assumption of the equilibrium state of gravel surfaces in flume experiments under feeding or recirculating conditions is generally justified by three equilibrium criteria based on sediment transport, slopes, and bed features. When these parameters become stable, an experiment is expected to reach equilibrium. This equilibrium state, however, is based on a one‐dimensional model, the Exner equation, which may not truly reflect the equilibrium state of the system considering the complex flow and sediment processes. In this paper, the evolutionary process of a gravel surface is investigated based on a large‐scale recirculating flume experiment. The performances of the three equilibrium criteria are evaluated first, and then the evolution of the bed morphology is studied. The key findings include the following: (1) the sediment transport rate, slopes of water and bed surfaces, and one‐dimensional morphological features reach equilibrium roughly simultaneously; (2) two‐dimensional morphology continually evolves after these characteristics reach equilibrium, which is confirmed by the characteristics of the sediment transport process; and (3) the results from a numerical simulation suggest that a much longer time is required to reach an equilibrium state. Our results suggest that sufficient experimental time is required to investigate the equilibrium morphological characteristics of gravel surfaces, which is much longer than the equilibrium time reflected by the one‐dimensional equilibrium criteria. Copyright © 2017 John Wiley & Sons, Ltd.     

Field application of close‐range digital photogrammetry (CRDP) for grain‐scale fluvial morphology studies

In situ measurement of grain‐scale fluvial morphology is important for studies on grain roughness, sediment transport and the interactions between animals and the geomorphology, topics relevant to many river practitioners. Close‐range digital photogrammetry (CRDP) and terrestrial laser scanning (TLS) are the two most common techniques to obtain high‐resolution digital elevation models (DEMs) from fluvial surfaces. However, field application of topography remote sensing at the grain scale is presently hindered mainly by the tedious workflow challenges that one needs to overcome to obtain high‐accuracy elevation data. A recommended approach for CRDP to collect high‐resolution and high‐accuracy DEMs has been developed for gravel‐bed flume studies. The present paper investigates the deployment of the laboratory technique on three exposed gravel bars in a natural river environment. In contrast to other approaches, having the calibration carried out in the laboratory removes the need for independently surveyed ground‐control targets, and makes for an efficient and effective data collection in the field. Optimization of the gravel‐bed imagery helps DEM collection, without being impacted by variable lighting conditions. The benefit of a light‐weight three‐dimensional printed gravel‐bed model for DEM quality assessment is shown, and confirms the reliability of grain roughness data measured with CRDP. Imagery and DEM analysis evidences sedimentological contrasts between gravel bars within the reach. The analysis of the surface elevations shows the effect variable grain‐size and sediment sorting have on the surface roughness. By plotting the two‐dimensional structure functions and surface slopes and aspects we identify different grain arrangements and surface structures. The calculation of the inclination index allows determining the surface‐forming flow direction(s). We show that progress in topography remote sensing is important to extend our knowledge on fluvial morphology processes at the grain scale, and how a technique customized for use by fluvial geomorphologists in the field benefits this progress. Copyright © 2016 John Wiley & Sons, Ltd.