高层钢框架-混凝土核心筒混合结构振动台试验研究

为了研究高层钢框架-混凝土核心筒混合结构的整体抗震性能,本文设计了一个典型的比例为1/15的20层钢框架-混凝土核心筒混合结构的缩尺模型,在同济大学土木工程防灾国家重点实验室实施了模拟地震振动台试验。本文重点介绍试验中模型结构在各级水准地震作用下的动力特性、加速度和位移反应,描述了模型结构的破坏位置及过程,并根据相似理论得到了原型结构的地震反应。试验研究表明:原型结构基本能够满足我国现行规范"小震不坏、大震不倒"的抗震设防标准;核心筒发挥了主要抗侧力作用;结构在大震作用下有较好的延性;钢框架与核心筒的连接节点在结构设计时应给予重视。     

Shake table testing of a multi-tower connected hybrid structure

Many single-tower reinforced concrete core wall-steel frame (RCC-SF) buildings have been built in China, but there are no buildings of different-height multi-tower hybrid system. A multi-tower RCC-SF tall building was thus studied because of its structural complexity and irregularity. First, a 1/15 scaled model structure was designed and tested on the shake table under minor, moderate, and major earthquake levels. Then, the dynamic responses of the model structure were interpreted to those of the prototype structure according to the similitude theory. Experimental results demonstrate that, despite the complexity of the structure, the lateral deformation bends as the "bending type" and the RC core walls contribute more than the steel frames to resist seismic loads. The maximum inter-story drift of the complex building under minor earthquakes is slightly beyond the elastic limitation specified in the Chinese code, and meets code requirements under major earthquakes. From the test results some suggestions are provided that could contribute favorable effect on the seismic behavior and the displacement of the building.     

Investigation of dynamic response of masonry minaret structures

Almost all historical minarets in Turkey were constructed using cut stone, masonry blocks or combination of these two materials. The structural and geometrical properties of each masonry minaret, or slender tower structure, depend on many factors including the structural knowledge and applications at the time of construction, experience of the architect or engineer, seismicity of the region, and availability of construction materials in that area. Recent earthquakes in Turkey have shown that most masonry minarets in high seismic regions are vulnerable to structural damage and collapse. In this study, in order to investigate the dynamic behavior of historical unreinforced masonry minarets, three representative minarets with 20, 25, and 30 m height were modeled and analyzed using two ground motions recorded during the 1999 Kocaeli and Duzce, Turkey earthquakes. The modal analyses of the models have shown that the structural periods and the overall structural response are influenced by the minaret height and spectral characteristics of the input motion. The dynamic displacement and axial stress time histories are computed at the critical points on the minarets. During recent earthquakes, most minaret failures occurred above the base of the structure. Consistent with the observed response, the largest stresses were calculated at the same location.     

多维地震作用下钢筋混凝土建筑结构的抗连续倒塌仿真分析

为了提高钢筋混凝土建筑结构的抗震性能,分析多维地震作用下钢筋混凝土建筑结构的抗连续倒塌能力,结合钢筋混凝土建筑结构特性、节点构造特点以及其在多维地震作用下的破坏机理,采用离散单元法建立结构连续倒塌的理论模型,对建筑结构连续倒塌过程进行数值模拟。基于数值模拟化结果,通过备用荷载路径法,实现建筑结构的抗连续倒塌分析。仿真实验结果得出,所提方法能实现对建筑结构抗连续倒塌的准确分析,且在多维地震作用下建筑结构扭转的幅度明显变大,结构顶层位移发散状态显著,不同楼层会产生不同的层间位移以及薄弱部位,建筑结构的抗连续倒塌性能随着失效构件位置的提升而增强。     

近场地震下竖向刚度不同的混合结构动力性能分析

近场地震的动力特性明显不同于远场地震,因此有必要对结构在近场地震作用下的动力性能展开研究。以上部钢结构-下部混凝土结构这类竖向刚度不同的加层混合结构为研究对象,对其在近场脉冲型地震、近场无脉冲型地震及远场地震作用下的动力响应进行研究。结果表明:在多遇、设防、罕遇地震作用下,近场脉冲型地震会使结构的层间位移角、层间剪力、加速度等动力响应均放大并出现超限的情况,而且都比罕遇地震作用下结构的响应增大更明显;在进行近场区加层混合框架结构的设计和建设时,近场脉冲效应会使结构存在不满足规范的情况,有必要对竖向刚度不同的加层混合结构在近场区的适用性进行深入研究。     

混凝土高层建筑结构地震破坏抗毁能力评估

提出基于构件性能的混凝土高层建筑结构地震破坏抗毁能力评估方法,采用强度与延性法分析混凝土高层建筑构件强度和变形,以对强震作用下混凝土高层建筑结构性能实施准确描述。基于建筑结构性能以及多条地震波情况下高层建筑结构倒塌极限状态的分析规范,采用IDA方法设置建筑结构抗倒塌能力系数,并依据该系数获取基于构件性能的混凝土高层建筑结构地震破坏抗毁能力评估流程,实现建筑结构地震破坏抗毁能力的准确评估。实验结果说明,所提方法实现了混凝土高层建筑结构地震破坏抗毁能力的准确评估。     

基于性能的基础隔震钢筋混凝土框剪结构的倒塌可靠度分析

利用基于性能的结构可靠度分析方法,对基础隔震钢筋混凝土框剪结构进行分析研究。选取20条实际地震动记录,以0.2g为步长对结构地震动参数PGA进行调幅后,建立了140个结构-地震动样本空间。选取上部结构的最大层间位移角、隔震层位移为量化指标,对每一个样本进行动力非线性时程分析后,将结构响应进行统计得到结构在各地震动强度下超越极限破坏状态的概率,将其绘制成基础隔震钢筋混凝土框剪结构的易损性曲线并利用整体可靠度方法分析结构发生倒塌的可靠度指标。该方法直观地反映了结构发生倒塌的概率,为结构的地震损失评估提供依据。     

Comparative performance of friction damped systems and base isolation systems for earthquake retrofit and aseismic design

The seismic performance of a steel framed structure equipped with (i) friction damping devices and (ii) base isolators is compared. A parametric study based on energy concepts is performed first using time-history dynamic analysis to determine the optimum properties of the two systems when excited by an earthquake whose energy is distributed over a relatively broad frequency band (1940 El Centro, N-S). Using these same properties, the responses of the two structural systems are then examined when excited by earthquakes whose power content essentially is concentrated at the low frequency end of the energy spectrum (1977 Romania, Bucharest, N-S and 1985 Mexico, SCT E-W). The results of the study show that, while both systems similarly reduce the response of conventional structures to the California earthquake, the friction damped structure exhibits a superior performance under the low frequency earthquakes. Very large shear forces and displacements are observed when the Romania and Mexico earthquakes are applied to the base isolated structure, indicating that the performance of a base isolated structure depends on the characteristics of the site earthquake. By comparison, friction damped structures are shown to behave favourably under the three earthquakes studied; this suggests that friction damping devices offer a more consistent way of protecting structures during earthquakes.     

Development of seismic force requirements for buildings in Taiwan

This paper describes static and dynamic procedures to calculate seismic demand specified by the current seismic design code for buildings in Taiwan,which was issued in 2005.For design levels with a return period of475 years,the design spectral response acceleration can be developed for general sites,near-fault sites and Taipei Basin.In addition,in order to prevent building collapse during extremely large earthquakes and yielding of structural components and elements during frequent small earthquakes,the ...     

基于推覆分析的钢框架结构地震倒塌判别准则研究

结构地震倒塌判别准则是工程结构强震分析的关键问题。在层损伤模型的基础上,建立了基于推覆分析的建筑结构整体损伤模型,并以国内某2层2跨平面钢框架结构拟静力试验为背景,应用有限元程序ABAQUS对平面钢框架进行了强震倒塌数值模拟。分析了钢框架结构的倒塌破坏过程,基于建议地震倒塌判别准则研究了钢框架结构的损伤演化规律。结果表明:钢框架结构在强震作用下的损伤发展顺序与塑性发展顺序一致;基于推覆分析的结构整体损伤模型能较好的体现强震作用下钢框架结构的损伤演化规律,且在上下界处收敛;强震作用下,钢框架结构的初始损伤主要由结构的残余侧移引起,而后期损伤主要由结构的承载力和刚度退化引起。     

Validation of the SCEC Broadband Platform simulations for tall building risk assessments considering spectral shape and duration of the ground motion

Earthquake simulation technologies are advancing to the stage of enabling realistic simulations of past earthquakes as well as characterizations of more extreme events, thus holding promise of yielding novel insights and data for earthquake engineering. With the goal of developing confidence in the engineering applications of simulated ground motions, this paper focuses on validation of simulations for response history analysis through comparative assessments of building performance obtained using sets of recorded and simulated motions. Simulated ground motions of past earthquakes, obtained through a larger validation study of the Southern California Earthquake Center Broadband Platform, are used for the case study. Two tall buildings, a 20‐story concrete frame and a 42‐story concrete core wall building, are analyzed under comparable sets of simulated and recorded motions at increasing levels of ground motion intensity, up to structural collapse, to check for statistically significant differences between the responses to simulated and recorded motions. Spectral shape and significant duration are explicitly considered when selecting ground motions. Considered demands include story drift ratios, floor accelerations, and collapse response. These comparisons not only yield similar results in most cases but also reveal instances where certain simulated ground motions can result in biased responses. The source of bias is traced to differences in correlations of spectral values in some of the stochastic ground motion simulations. When the differences in correlations are removed, simulated and recorded motions yield comparable results. This study highlights the utility of physics‐based simulations, and particularly the Southern California Earthquake Center Broadband Platform as a useful tool for engineering applications.     

Strength failure of spatial reticulated structures under multi-support excitation

Under strong earthquakes, long-span spatial latticed structures may collapse due to dynamic instability or strength failure. The elasto-plastic dynamic behaviors of three spatial latticed structures, including two double-layer cylindrical shells and one spherical shell constructed for the 2008 Olympic Games in Beijing, were quantitatively examined under multi-support excitation (MSE) and uniform support excitation (USE). In the numerical analyses, several important parameters were investigated such as the peak acceleration and displacement responses at key joints, the number and distribution of plastic members, and the deformation of the shell at the moment of collapse. Analysis results reveal the features and the failure mechanism of the spatial latticed structures under MSE and USE. In both scenarios, the double-layer reticulated shell collapses in the "overflow" mode, and the collapse is governed by the number of invalid plastic members rather than the total number of plastic members, beginning with damage to some of the local regions near the supports. By comparing the numbers and distributions of the plastic members under MSE to those under USE, it was observed that the plastic members spread more sufficiently and the internal forces are more uniform under MSE, especially in cases of lower apparent velocities in soils. Due to the effects of pseudo-static displacement, the stresses in the members near the supports under MSE are higher than those under USE.     

Shake‐table tests of a reinforced concrete frame designed following modern codes: seismic performance and damage evaluation

This paper presents shake‐table tests conducted on a two‐fifths‐scale reinforced concrete frame representing a conventional construction design under current building code provisions in the Mediterranean area. The structure was subjected to a sequence of dynamic tests including free vibrations and four seismic simulations in which a historical ground motion record was scaled to levels of increasing intensity until collapse. Each seismic simulation was associated with a different level of seismic hazard, representing very frequent, frequent, rare and very rare earthquakes. The structure remained basically undamaged and within the inter‐story drift limits of the ‘immediate occupancy’ performance level for the very frequent and frequent earthquakes. For the rare earthquake, the specimen sustained significant damage with chord rotations of up to 28% of its ultimate capacity and approached the upper bound limit of inter‐story drift associated with ‘life safety’. The specimen collapsed at the beginning of the ‘very rare’ seismic simulation. Besides summarizing the experimental program, this paper evaluates the damage quantitatively at the global and local levels in terms of chord rotation and other damage indexes, together with the energy dissipation demands for each level of seismic hazard. Further, the ratios of column‐to‐beam moment capacity recommended by Eurocode 8 and ACI‐318 to guarantee the formation of a strong column‐weak beam mechanism are examined. Copyright © 2013 John Wiley & Sons, Ltd.     

Energy capacity and seismic performance of RC waffle-flat plate structures under two components of far-field ground motions: Shake table tests

The bidirectional response of a portion of a reinforced concrete (RC) waffle-flat plate (WFP) structure subjected to far-field ground motions is studied through shake table tests. The test specimen is a scaled portion of a prototype structure designed under current building codes and located in a region of moderate seismicity of the Mediterranean area. The specimen was subjected to a sequence of tests of increasing acceleration amplitude that respectively represented very frequent, frequent, design, and very rare earthquakes at the site. The test structure performed well (basically in the elastic domain) under very frequent and frequent earthquakes, approached the boundary between the performance levels of life safety and near collapse under the design earthquake, and collapsed under the very rare earthquake. Damage concentrated at column bases and at the transverse beams of the exterior plate-to-column connection. Columns dissipated about 10% of the total energy that contributes to damage, and the rest was dissipated by the exterior plate-column connection. The total energy input on the structure until collapse under the bidirectional seismic action was very close to the value obtained in previous studies on a similar specimen tested under unidirectional ground motions. The capacity curve estimated from the experimental base shear vs top displacement relationship suggests it is best to use a behavior factor of at most q = 2 when designing WFP structures with the reduced-spectrum force-based approach.     

核心筒部分悬挂结构抗震分析的简化力学模型

提出了核心筒部分悬挂结构体系,在已有该体系振动台试验基础上,建立了该体系的抗震分析简化力学模型及其理论公式。按小震、中震和大震3种不同的地震作用情况,分析了该结构体系力学模型和动力方程的差异。利用有限元分析程序SAP2000,对这种结构体系进行了小震和大震作用下的结构地震反应分析,计算结果与试验结果吻合较好。     

强震区非对称连续梁桥地震响应及性能评价

为研究高烈度地区不等跨连续梁桥的抗震性能，依托某高速公路上一座主跨为（40+60+35）m的典型不等跨连续梁桥，建立其动力分析有限元模型，获得该桥的模态特性。在E1概率和E2概率两种地震水平作用下，同时采用反应谱分析和时程分析法，对不等跨桥梁结构的地震响应进行分析。最后根据桥墩验算截面的弯矩-曲率关系曲线，探讨该桥梁的抗震性能。研究结果表明：动态时程反应分析与反应谱分析所得的结果基本吻合，由于反应谱分析假定结构线弹性状态而时程反应分析考虑了材料的弹塑性，在E2概率水平下，两者个别响应值有较大差别；由于反应谱法是对各阶模态下最大响应的组合，动态时程反应分析是同一时刻各地震波引起的结构响应的组合，因而时域和频域计算结果会存在一些误差，频域结果偏于保守；E1、E2概率地震作用下，主桥桥墩检算截面仍然在弹性范围内工作，满足弹性设计要求。     

Unsupervised fuzzy neural network structural active pulse controller

Applying active control systems to civil engineering structures subjected to dynamic loading has received increasing interest. This study proposes an active pulse control model, termed unsupervised fuzzy neural network structural active pulse controller (UFN‐SAP controller), for controlling civil engineering structures under dynamic loading. The proposed controller combines an unsupervised neural network classification (UNC) model, an unsupervised fuzzy neural network (UFN) reasoning model, and an active pulse control strategy. The UFN‐SAP controller minimizes structural cumulative responses during earthquakes by applying active pulse control forces determined via the UFN model based on the clusters, classified through the UNC model, with their corresponding control forces. Herein, we assume that the effect of the pulses on structure is delayed until just before the next sampling time so that the control force can be calculated in time, and applied. The UFN‐SAP controller also averts the difficulty of obtaining system parameters for a real structure for the algorithm to allow active structural control. Illustrative examples reveal significant reductions in cumulative structural responses, proving the feasibility of applying the adaptive unsupervised neural network with the fuzzy classification approach to control civil engineering structures under dynamic loading. Copyright © 2001 John Wiley & Sons, Ltd.     

上海浦东国际机场T2航站楼弹塑性时程分析

上海浦东机场T2航站楼结构为复杂大跨混合结构,本文采用NosaCAD2005有限元程序建立结构分析模型,模型主要由非线性杆单元组成,包括梁、柱和二力杆单元,梁、柱采用三段变刚度杆模型,以受弯为主的梁单元截面弯矩-曲率关系采用二折线和三折线模型,柱和二力杆截面采用纤维模型。通过多遇和罕遇烈度下的弹塑性时程分析,研究了该结构的变形、内力、破坏情况的发展历程。计算结果表明,该结构可以满足"小震不坏,大震不倒"的设防要求。     

Collapse assessment of moment frame buildings,considering vertical ground shaking

While many cases of structural damage in past earthquakes have been attributed to strong vertical ground shaking, our understanding of vertical seismic load effects and their influence on collapse mechanisms of buildings is limited. This study quantifies ground motion parameters that are capable of predicting trends in building collapse because of vertical shaking, identifies the types of buildings that are most likely affected by strong vertical ground motions, and investigates the relationship between element level responses and structural collapse under multi‐directional shaking. To do so, two sets of incremental dynamic analyses (IDA) are run on five nonlinear building models of varying height, geometry, and design era. The first IDA is run using the horizontal component alone; the second IDA applies the vertical and horizontal motions simultaneously. When ground motion parameters are considered independently, acceleration‐based measures of the vertical shaking best predict trends in building collapse associated with vertical shaking. When multiple parameters are considered, Housner intensity (SI), computed as a ratio between vertical and horizontal components of a record (SI_V/SI_H), predicts the significance of vertical shaking for collapse. The building with extensive structural cantilevered members is the most influenced by vertical ground shaking, but all frame structures (with either flexural and shear critical columns) are impacted. In addition, the load effect from vertical ground motions is found to be significantly larger than the nominal value used in US building design. Copyright © 2016 John Wiley & Sons, Ltd.     

基于OpenSees的强震下混凝土结构梁-梁碰撞行为数值实现

绝大多数针对极端作用下的结构连续倒塌分析,在分析过程中不能实时地根据构件的损伤状态对分析模型进行修改,也不能考虑连续倒塌过程中的各种碰撞问题。连续倒塌过程中发生的碰撞对结构响应预测有重大影响。本文依据钢筋混凝土框架结构发生梁-梁碰撞的机理,基于OpenSees平台建模,结合Matlab的混合编程计算碰撞力,通过添加碰撞时程力并对结构进行模型更新,合理地实现钢筋混凝土框架结构在强震作用下的连续倒塌过程中发生梁-梁碰撞的具体过程。将得到的结果和传统时程分析法的结果进行的对比表明,结合Matlab和OpenSees命令可以实时地计算碰撞力序列和对结构进行更新,梁-梁碰撞和构件的逐步失效使结构的水平位移和转角有一定的增大,竖向位移有一定减小。