Joint isotopic mass balance: a novel approach to quantifying channel bed to channel margins sediment transfer during storm events

The important role of floodplains and the broader riparian zone in providing temporary storage for a large fraction of the annual sediment load of rivers is well established, but this understanding is largely based on observations of the long‐term average behavior of the catchment. Here we combine measurements of the fallout radionuclides ⁷Be and ²¹⁰Pb and the stable isotopes of hydrogen in water to quantify fine sediment mobilization and storage in a stream and its channel margins during individual intermediate‐sized storm events with recurrence intervals of a few months or less. We demonstrate this method using five storm events in a small (~15 km²), undeveloped, gravel‐bedded tributary of the Connecticut River (USA). We estimate that in each storm, the mass of sediment deposited onto the margins accounts for almost 90% of the sediment mobilized from the bed, with the remainder of the mobilized bed sediment transported downstream as suspended load. The result that the bed is a net source of sediment to the stream and the margins a net sink is robust, but estimates of the mass of material eroded from the bed and deposited on the margins are less certain. The source of sediment to the bed remains unclear as, consistent with earlier studies, we observe only limited deposition of sediment to the bed during the storm events. The suspended sediment is organic‐rich and thus its source may be associated with in‐channel organic decay between storm events. Understanding the coupled interactions between discharge magnitude and frequency and sediment resupply at the event time scale has important implications for stream restoration efforts seeking to connect the channel and the broader riparian zone, and for the development of accurate sediment budgets and predictions of sediment flux from a watershed. Copyright © 2015 John Wiley & Sons, Ltd.     

Using radiometric fingerprinting and phosphorus to elucidate sediment transport dynamics in an agricultural watershed

The major goals of this study were to determine stream bed sediment erosion/deposition rates, sediment age, percent ‘new’ sediment, and suspended sediment origin during two storm events of contrasting magnitudes (11.9 mm over 5 h and 58.9 mm over 39 h) using fallout radionuclides (excess lead 210 – ²¹⁰Pb_xs and beryllium 7 – ⁷Be) and link the nature and type of sediment source contributions to potential phosphorus (P) off‐site transport. The study was conducted in cropland‐dominated and mixed land use subwatersheds in the non‐glaciated Pleasant Valley watershed (50 km²) in South Central Wisconsin. Fine sediment deposition and erosion rates on stream beds varied from 0.76 to 119.29 mg cm^?2 day^?1 (at sites near the watershed outlet) and 1.72 to 7.72 mg cm^?2 day^?1 (at sites in the headwaters), respectively, during the two storm events. The suspended sediment age ranged from 123 ± 12 to 234 ± 33 days during the smaller storm event; however, older sediment was more prevalent (p = 0.037) in the streams during the larger event with suspended sediment age ranging from 226 ± 9 to 322 ± 114 days. During the small and large storm event, percent new sediment in suspended sediment ranged from 5.3 ± 2.1 to 21.0 ± 2.9% and 5.3 ± 2.7 to 6.7 ± 5.7%, respectively. In the cropland‐dominated subwatershed, upland soils were the major source of suspended sediment, whereas in the mixed land use subwatershed, both uplands and stream banks had relatively similar contributions to suspended sediment. In‐stream (suspended and bed) sediment P levels ranged from 703 ± 193 to 963 ± 84 mg kg^?1 during the two storm events. The P concentrations in suspended and bed sediment were reflective of the dominant sediment source (upland or stream bank or mixed). Overall, sediment transport dynamics showed significant variability between subwatersheds of different land use characteristics during two contrasting storm events. Copyright © 2014 John Wiley & Sons, Ltd.     

Fine sediment delivery and transfer in lowland catchments: modelling suspended sediment concentrations in response to hydrological forcing

Fine sediment delivery to and storage in stream channel reaches can disrupt aquatic habitats, impact river hydromorphology, and transfer adsorbed nutrients and pollutants from catchment slopes to the fluvial system. This paper presents a modelling tool for simulating the time‐dependent response of the fine sediment system in catchments, using an integrated approach that incorporates both land phase and in‐stream processes of sediment generation, storage and transfer. The performance of the model is demonstrated by applying it to simulate in‐stream suspended sediment concentrations in two lowland catchments in southern England, the Enborne and the Lambourn, which exhibit contrasting hydrological and sediment responses due to differences in substrate permeability. The sediment model performs well in the Enborne catchment, where direct runoff events are frequent and peak suspended sediment concentrations can exceed 600 mg l^?1. The general trends in the in‐stream concentrations in the Lambourn catchment are also reproduced by the model, although the observed concentrations are low (rarely exceeding 50 mg l^?1) and the background variability in the concentrations is not fully characterized by the model. Direct runoff events are rare in this highly permeable catchment, resulting in a weak coupling between the sediment delivery system and the catchment hydrology. The generic performance of the model is also assessed using a generalized sensitivity analysis based on the parameter bounds identified in the catchment applications. Results indicate that the hydrological parameters contributing to the sediment response include those controlling (1) the partitioning of runoff between surface and soil zone flows and (2) the fractional loss of direct runoff volume prior to channel delivery. The principal sediment processes controlling model behaviour in the simulations are the transport capacity of direct runoff and the in‐stream generation, storage and release of the fine sediment fraction. The in‐stream processes appear to be important in maintaining the suspended sediment concentrations during low flows in the River Enborne and throughout much of the year in the River Lambourn. Copyright © 2007 John Wiley & Sons, Ltd.     

Suspended sediment transport regime in a debris‐flow gully on Vancouver Island,British Columbia

In debris‐flow‐prone channels, normal fluvial sediment transport occurs (nearly exclusively in suspended mode) between episodic debris‐flow events. Observations of suspended sediment transport through a winter season in a steepland gully in logged terrain revealed two event types. When flows exceeded a threshold of 270 l s⁻¹, events yielded significant quantities of sediment and suspended sediment concentration increased with flow. Smaller events were strongly ‘supply limited’; sediment concentration decreased as flow increased. Overall, there is no consistent correlation between runoff and sediment yield. Within the season, three subseasons were identified (demarcated by periods of freezing weather) within which a pattern of fine sediment replenishment and evacuation occurred. Finally, a signature of fine sediment mobilization and exhaustion was observed within individual events. Fine sediment transport occurred in discrete pulses within storm periods, most of the yield occurring within 5 to 15% of storm runoff duration, so that it is unlikely that scheduled sampling programs would identify significant transport. Significant events are, however, generally forecastable on the basis of regional heavy rainfall warnings, providing a basis for targeted observations. Radiative snowmelt events and rain‐on‐snow remain difficult to forecast, since the projection of temperatures from the nearest regular weather station yields variable results. Copyright © 2004 John Wiley & Sons, Ltd.     

The effects of sample scheduling and sample numbers on estimates of the annual fluxes of suspended sediment in fluvial systems

Since the 1970s, there has been both continuing and growing interest in developing accurate estimates of the annual fluvial transport (fluxes and loads) of suspended sediment and sediment‐associated chemical constituents. This study provides an evaluation of the effects of manual sample numbers (from 4 to 12 year^?1) and sample scheduling (random‐based, calendar‐based and hydrology‐based) on the precision, bias and accuracy of annual suspended sediment flux estimates. The evaluation is based on data from selected US Geological Survey daily suspended sediment stations in the USA and covers basins ranging in area from just over 900 km² to nearly 2 million km² and annual suspended sediment fluxes ranging from about 4 Kt year^?1 to about 200 Mt year^?1. The results appear to indicate that there is a scale effect for random‐based and calendar‐based sampling schemes, with larger sample numbers required as basin size decreases. All the sampling schemes evaluated display some level of positive (overestimates) or negative (underestimates) bias. The study further indicates that hydrology‐based sampling schemes are likely to generate the most accurate annual suspended sediment flux estimates with the fewest number of samples, regardless of basin size. This type of scheme seems most appropriate when the determination of suspended sediment concentrations, sediment‐associated chemical concentrations, annual suspended sediment and annual suspended sediment‐associated chemical fluxes only represent a few of the parameters of interest in multidisciplinary, multiparameter monitoring programmes. The results are just as applicable to the calibration of autosamplers/suspended sediment surrogates currently used to measure/estimate suspended sediment concentrations and ultimately, annual suspended sediment fluxes, because manual samples are required to adjust the sample data/measurements generated by these techniques so that they provide depth‐integrated and cross‐sectionally representative data. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.     

Continuous measurement of spectrophotometric absorbance in peatland streamwater in northern England: implications for understanding fluvial carbon fluxes

Bog systems tend to have a flashy hydrological regime with low baseflows and rapid and high storm peaks. Water derived from peatlands often contains significant amounts of organic humic and fulvic materials which form the largest fraction of the dissolved organic carbon component of the fluvial carbon flux. However, most estimates of dissolved organic carbon flux from peatlands are based on sampling that is infrequent and which may miss the periods of high flux during storm events. In order to better characterize the behaviour and fluxes of fluvial carbon it is necessary to operate more frequent sampling. This paper presents data from a continuously operating field‐based spectrophotometer simultaneously measuring absorbance across 200–730 nm at 2·5 nm intervals in runoff from an upland peatland stream. It is shown that absorbance at different wavelengths that have previously been used to characterize dissolved organic carbon varies rapidly during storm events. The probe is shown to even detect changes in absorbance characteristics in response to rainfall events before the stream discharge starts to rise. The high‐resolution behaviour of absorbance characteristics during storm events is different depending on the wavelength studied. Thus, the choice of wavelength used as a proxy for dissolved organic carbon needs careful attention and it may be that automated spectrophotometric methods which provide rich time‐series data from across the spectrum can tell us more about fluxes, processes and sources of aquatic carbon in peatland systems in the future than traditional practices have hitherto allowed. Copyright © 2011 John Wiley & Sons, Ltd.     

Monitoring urban impacts on suspended sediment,trace element,and nutrient fluxes within the City of Atlanta,Georgia, USA: program design,methodological considerations,and initial results

Atlanta, Georgia (City of Atlanta, COA), is one of the most rapidly growing urban areas in the US. Beginning in 2003, the US Geological Survey established a long‐term water‐quantity/quality monitoring network for the COA. The results obtained during the first 2 years have provided insights into the requirements needed to determine the extent of urban impacts on water quality, especially in terms of estimating the annual fluxes of suspended sediment, trace/major elements, and nutrients. During 2004/2005, suspended sediment fluxes from the City of Atlanta (COA) amounted to about 150 000 t year^?1; ≥ 94% of the transport occurred in conjunction with storm‐flow, which also accounted for ≥ 65% of the annual discharge. Typically, storm‐flow averaged ≤20% of the year. Normally, annual suspended sediment fluxes are determined by summing daily loads based on a single calculation step using mean‐daily discharge and a single rating curve‐derived suspended sediment concentration. Due to the small and ‘flashy’ nature of the COAs streams, this approach could produce underestimates ranging from 25% to 64%. Accurate estimates ( ± 15%) require calculation time‐steps as short as every 2–3 h. Based on annual median base‐flow/storm‐flow chemical concentrations, the annual fluxes of ≥ 75% of trace elements (e.g. Cu, Pb, Zn), major elements (e.g. Fe, Al), and total P occur in association with suspended sediment; in turn, ≥ 90% of the transport of these constituents occur in conjunction with storm‐flow. As such, base‐flow sediment‐associated and dissolved contributions represent relatively insignificant portions of the total annual load. An exception is total N, whose sediment‐associated fluxes range from 50% to 60%; even so, storm‐related transport typically exceeds 80%. Hence, in urban environments, non‐point‐sources appear to be the dominant contributors to the fluxes of these constituents. Published in 2007by John Wiley & Sons, Ltd.     

Variability of particulate (SS,POC) and dissolved (DOC,NO3) matter during storm events in the Alegria agricultural watershed

The temporal variability of suspended sediment, nitrates (NO₃) and dissolved (DOC) and particulate organic carbon concentrations was analysed in the Alegria agricultural watershed over a 2‐year period. Nine storm events were studied, including an exhaustive analysis of hydrometeorological conditions, quantification of fluxes, and concentration‐discharge hysteresis loop characterization. The overall aim was to study the variability in these components during storm events and determine the mechanisms (flow paths) affecting the trajectories, from the source to the stream. The forms, rotational patterns and trends of hysteretic loops were investigated, and relationships between hysteresis features and hydrological parameters were studied. The results revealed clear differences between particulate (suspended sediment, particulate organic carbon) and dissolved (DOC, NO₃) matter transport responses. Movement of the particulate matter was attributed to surface water, as reflected in clockwise hysteresis loops, whereas dissolved matter showed, in general, counterclockwise hysteresis loops, indicating a time delay in the arrival of solutes to the stream. This could be related to subsurface flow paths for DOC and a groundwater source for NO₃. Copyright © 2013 John Wiley & Sons, Ltd.     

Estimation of suspended sediment sources using 137Cs and 210Pbex in unmanaged Japanese cypress plantation watersheds in southern Japan

To analyse suspended sediment sources in unmanaged Japanese cypress plantation watersheds, field measurements and fingerprinting of the suspended sediment was conducted in the Shimanto River basin in southern Japan. For sediment fingerprinting, ¹³⁷Cs and ²¹⁰Pb_ex were detected by means of gamma‐ray spectrometry in the surface soil of the forest floor, stream bank and truck trail and mobilized sediment by interrill erosion. The ¹³⁷Cs and ²¹⁰Pb_ex activities associated with the forest floor materials were considerably higher than those of the stream bank and truck trail. The ¹³⁷Cs and ²¹⁰Pb_ex activities associated with the suspended sediment were found to vary with the sampling period. Evidently, the suspended sediment can comprise materials generated from the forest floor by interrill erosion and those from the truck trail and/or stream bank. The multivariate sediment‐mixing model using ¹³⁷Cs and ²¹⁰Pb_ex showed that the contribution of the forest floor varied periodically, ranging from 23–56% in the Hinoki 156 subwatershed and from 18–85% in the Hinoki 155 subwatershed. The difference in the average contribution of the forest floor between Hinoki 156 (46%) and Hinoki 155 (69%) may relate to the presence of truck trail networks in the watershed. The truck trail network can play roles of sediment source and pathway for sediment from forest floor to stream channel due to the concentrated overland flow on the truck trail during heavy rainfall events. These results indicate that the forest floor should be recognized as a major source of suspended sediment in unmanaged Japanese cypress plantation watersheds. Copyright © 2008 John Wiley & Sons, Ltd.     

Sediment and particulate phosphorus characteristics in grassed waterways from row crop corn and alfalfa fields collected by manual University of Exeter samplers and automatic sampling

Phosphorus (P) export from agricultural lands above known threshold levels can result in adverse impacts to receiving water quality. Phosphorus loss occurs in dissolved and sediment‐bound, or particulate phosphorous (PP), forms, with the latter often dominating losses from row‐cropped systems. To target practices, land managers need good computer models and model developers need good monitoring data. Sediment monitoring data (e.g. radiometric finger printing and sediment P sorption capacity) can help identify sediment source areas and improve models, but require more sediment mass than is typically obtained by automatic sampling. This study compares a simple suspended sediment sampler developed at the University of Exeter (UE) with automatic sampling in intermittent channels draining corn and alfalfa fields. The corn field had a greater runoff coefficient (27%) than alfalfa (11%). No differences were found in enrichment ratios (sediment constituent/soil constituent) in PP (PP_ER) or percent loss on ignition (LOI_ER) between paired UE samplers on corn. The median LOI_ER for the UE samplers (1·9%) did not differ significantly (p > 0·13) from the automatic sampler (2·0%). The PP_ER from the UE samplers was on average 20% lower than the automatic samplers. A correlation (r² = 0·75) was found between sediment PP and % LOI from automatic samplers and UE samplers for particles < 50 µm, while for > 50 µm PP concentration did not change with changes in % LOI. Sediment ammonium‐oxalate extractable metals were similarly related to LOI, with the strongest correlation for iron (r² = 0·71) and magnesium (r² = 0·70). Copyright © 2011 John Wiley & Sons, Ltd.     

Estimating suspended sediment concentrations from turbidity measurements and the calibration problem

In situ turbidity meters are being increasingly used to generate continuous records of suspended sediment concentration in rivers. However, the usefulness of the information obtained depends heavily on the existence of a close relationship between fluctuations in suspended sediment concentration and turbidity and the calibration procedure that relates suspended sediment concentration to the turbidity meter's signal. This study assesses the relationship between suspended sediment concentration and turbidity for a small (1·19 km²) rural catchment in southern Brazil and evaluates two calibration methods by comparing the estimates of suspended sediment concentration obtained from the calibrated turbidity readings with direct measurements obtained using a USDH 48 suspended sediment sampler. With the first calibration method, the calibration relationship is derived by relating the turbidity readings to simultaneous measurements of concentration obtained from suspended sediment samples collected from the vicinity of the turbidity probe during flood events. With the second method, the calibration is based on the readings obtained from the turbidity meter when the probe immersed in samples of known concentration prepared using soils collected from the catchment. Overall, there was a close link between fluctuations in suspended sediment concentration and turbidity in the stream at the outlet of the catchment, and the estimates of sediment concentration obtained using the first calibration method corresponded closely with the conventionally measured sediment concentrations. However, use of the second calibration method introduced appreciable errors. When the estimated sediment concentrations were compared with the measured values, the mean errors were ± 122 mg l^?1 and + 601 mg l^?1 for the first and second calibration procedures respectively. Copyright © 2007 John Wiley & Sons, Ltd.     

Runoff and sediment generation on bench‐terraced hillsides: measurements and up‐scaling of a field‐based model

Despite widespread bench‐terracing, stream sediment yields from agricultural hillsides in upland West Java remain high. We studied the causes of this lack of effect by combining measurements at different spatial scales using an erosion process model. Event runoff and sediment yield from two 4‐ha terraced hillside subcatchments were measured and field surveys of land use, bench‐terrace geometry and storage of sediment in the drainage network were conducted for two consecutive years. Runoff was 3·0–3·9% of rainfall and sediment yield was 11–30 t ha⁻¹ yr⁻¹ for different years, subcatchments and calculation techniques. Sediment storage changes in the subcatchment drainage network were less than 2 t ha⁻¹, whereas an additional 0·3–1·5 t ha⁻¹ was stored in the gully between the subcatchment flumes and the main stream. This suggests mean annual sediment delivery ratios of 86–125%, or 80–104% if this additional storage is included. The Terrace Erosion and Sediment Transport (TEST) model developed and validated for the studied environment was parameterized using erosion plot studies, land use surveys and digital terrain analysis to simulate runoff and sediment generation on the terraced hillsides. This resulted in over‐estimates of runoff and under‐estimates of runoff sediment concentration. Relatively poor model performance was attributed to sample bias in the six erosion plots used for model calibration and unaccounted covariance between important terrain attributes such as slope, infiltration capacity, soil conservation works and vegetation cover. Copyright © 2005 John Wiley & Sons, Ltd.     

Sensitivity of runoff and soil erosion to climate change in two Mediterranean watersheds. Part I: model parameterization and evaluation

Climate change is expected to effect storm runoff and erosion processes in Mediterranean watersheds at multiple spatial scales. Models are typically applied to estimate these impacts; however, the scarcity of spatially distributed data for parameterization, calibration and validation often prevents application of these models, particularly for larger catchments. This report, the first part of a two‐part article, presents an application and evaluation of the MEFIDIS model for two Mediterranean meso‐scale watersheds (115 and 290 km²) in a data‐scarce environment. A multi‐scale assessment method was used that combines quantitative validation and qualitative evaluation, consisting of three steps: (1) calibration at the small (field) scale using results from rainfall simulation experiments; (2) calibration and validation for catchment‐scale results while changing catchment‐scale parameters only (channel roughness and a parameter controlling the distribution of saturated areas); and (3) qualitative evaluation of within‐watershed erosion processes using empirical estimates of sediment delivery ratio and gully location. The results indicate that calibrating MEFIDIS at the field scale can provide reasonable results for catchment runoff and sediment export and for within‐watershed erosion processes. Copyright © 2009 John Wiley & Sons, Ltd.     

Release of dissolved organic carbon from upland peat

This study examines the release of dissolved organic carbon (DOC) from upland peat during the period of the autumn flushing. Hydroclimatic conditions were monitored in conjunction with measurements of absorbance and the E4/E6 ratio of the stream draining an 11·4 km² upland peat catchment in northern England. During two months of monitoring the effects of 67 separate rainfall events were examined showing that:

• The peat behaves hydrologically as if it were a two end‐member system consisting of old, interevent, and new, event, water. Runoff is initiated by percolation excess of new water at the acrotelm–catotelm interface.
• The discharge of dissolved organic matter behaves like a three end‐member system with the between‐event water being low in DOC and storm events being characterized by two types of water. Initial runoff being characterized by new water rich in DOC that gives way to new water depleted in DOC. This transition can be ascribed to the runoff progressing from throughflow within the acrotelm progressing to saturation‐excess overland flow.
• Depletion of DOC during storm events is accompanied by a change in the character of the DOC as the E4/E6 ratio changes. This suggests that the decrease in DOC during events is the result of exhaustion of reserves rather than changes in the flowpaths being utilized by runoff.
• The amount of carbon released in any event is critically dependent upon the time between events during which oxidation processes generate a reservoir of available carbon. Production of available carbon in the catchment is as high as 4·5 g C per day per m³ of peat, suggesting a turnover rate of peat of the order of 42 years. Copyright © 2002 John Wiley & Sons, Ltd.

     

Heavy metal release by peat erosion in the Peak District,southern Pennines,UK

Upper North Grain (UNG) is a heavily eroding blanket peat catchment in the Peak District, southern Pennines, UK. Concentrations of lead in the near‐surface peat layer at UNG are in excess of 1000 mg kg⁻¹. For peatland environments, these lead concentrations are some of the highest globally. High concentrations of industrially derived, atmospherically transported magnetic spherules are also stored in the near‐surface peat layer. Samples of suspended sediment taken during a storm event that occurred on 1 November 2002 at UNG, and of the potential catchment sources for suspended sediments, were analysed for lead content and the environmental magnetic properties of anhysteretic remanent magnetization (ARM) and saturation isothermal remanent magnetization (SIRM). At the beginning of the storm event, there is a peak in both suspended sediment and associated lead concentration. SIRM/ARM values for suspended sediment samples throughout the storm reveal that the initial ‘lead flush’ is associated with a specific sediment source, namely that of organic sediment eroded from the upper peat layer. Using the magnetic ‘fingerprinting’ approach to discrimination of sediment sources, this study reveals that erosion of the upper peat layer at UNG is releasing high concentrations of industrially derived lead (and, by inference, other toxic heavy metals associated with industrial particulates) into the fluvial systems of the southern Pennines. Climate‐change scenarios for the UK, involving higher summer temperatures and stormier winters, may result in an increased flux both of sediment‐associated and dissolved heavy metals from eroding peatland catchments in the southern Pennines, adversely affecting the quality of sediment and water entering reservoirs of the region. Copyright © 2005 John Wiley & Sons, Ltd.     

Runoff and road erosion at the plot and road segment scales,St John,US Virgin Islands

Previous studies have identified unpaved roads as the primary source of erosion on St John in the US Virgin Islands, but these studies estimated road erosion rates only as annual averages based primarily on road rill measurements. The goal of this project was to quantify the effect of unpaved roads on runoff and sediment production on St John, and to better understand the key controlling factors. To this end runoff and sediment yields were measured from July 1996 to March 1997 from three plots on naturally vegetated hillslopes, four plots on unpaved road surfaces and two cutslope plots. Sediment yields were also measured from seven road segments with contributing areas ranging from 90 to 700 m². With respect to the vegetated plots, only the two largest storm events generated runoff and there was no measurable sediment yield. Runoff from the road surface plots generally occurred when storm precipitation exceeded 6 mm. Sediment yields from the four road surface plots ranged from 0·9 to 15 kg m⁻² a⁻¹, and sediment concentrations were typically 20–80 kg m⁻³. Differences in runoff between the two cutslope plots were consistent with the difference in upslope contributing area. A sprinkler experiment confirmed that cross‐slope roads intercept shallow subsurface stormflow and convert this into surface runoff. At the road segment scale the estimated sediment yields were 0·1 to 7·4 kg m⁻² a⁻¹. Road surface runoff was best predicted by storm precipitation, while sediment yields for at least three of the four road surface plots were significantly correlated with storm rainfall, storm intensity and storm runoff. Sediment yields at the road segment scale were best predicted by road surface area, and sediment yields per unit area were most strongly correlated with road segment slope. The one road segment subjected to heavy traffic and more frequent regrading produced more than twice as much sediment per unit area than comparable segments with no truck traffic. Particle‐size analyses indicate a preferential erosion of fine particles from the road surface and a rapid surface coarsening of new roads. Published in 2001 by John Wiley & Sons, Ltd.     

Heavy metal concentrations during storm events in a rehabilitated industrialized catchment

Water quality data collected on a fortnightly or monthly basis are inadequate for assessment and modelling of many water quality problems as storm event samples are underrepresented or missed. This paper examines the stormflow dynamics of heavy metals (Pb, Cu, Cd and Zn) in the Nant‐y‐Fendrod stream, South Wales, which has been affected by 250 years of metal smelting, followed by 35 years of landscape rehabilitation measures. For storm events of contrasting (very dry and very wet) antecedent conditions in May 2000 and February 2001, respectively, temporal changes in streamwater heavy metal concentrations above and below an in‐line flood detention lake are analysed. At the upstream site, peaks in total metal concentration were recorded on the rising limb for Pb (0·150 mg l^?1) and Cu (0·038 mg l^?1) but on the falling limb for Zn (1·660 mg l^?1) and Cd (0·006 mg l^?1) in the summer 2000 storm event, yielding clockwise and anticlockwise hysteretic loops respectively. In contrast, metal concentrations, although high throughout the winter storm event, were diluted somewhat during the storm peak itself. The Pb and Cu appear to be supplied by quickflow processes and transported in close association with fine sediment, whereas Zn and Cd are delivered to the channel and lake by slower subsurface seepage in dissolved form. In the winter 2001 event, antecedent soil moisture and shallow groundwater levels were anomalously high and seepage sources of dissolved metals dominated. Downstream of the lake, Pb and Cu levels and suspended sediment were high in the summer storm, but low in the winter storm, suggesting retention with deposition of fine sediment in the lake during the latter. In the winter storm, Zn and Cd levels were higher downstream than upstream of the lake, perhaps because of additional seepage inputs from the surrounding slopes, which failed to have an impact during summer. An understanding of the complex interplay of antecedent soil moisture and the dynamics of subsurface seepage pathways in relation to the three‐dimensional distribution of sources is important in modelling heavy metal fluxes and levels in contaminated urban catchments. Copyright © 2003 John Wiley & Sons, Ltd.     

Streamflow and suspended sediment yield following the 2000 Bobcat fire,Colorado

Postfire runoff and erosion are a concern, and more data are needed on the effects of wildfire at the watershed‐scale, especially in the Colorado Front Range. The goal of this study was to characterize and compare the streamflow and suspended sediment yield response of two watersheds (Bobcat Gulch and Jug Gulch) after the 2000 Bobcat fire. Bobcat Gulch had several erosion control treatments applied after the fire, including aerial seeding, contour log felling, mulching, and straw wattles. Jug Gulch was partially seeded. Study objectives were to: (1) measure precipitation, streamflow, and sediment yields; (2) assess the effect of rainfall intensity on peak discharges, storm runoff, and sediment yields; (3) evaluate short‐term hydrologic recovery. Two months after the fire, a storm with a maximum 30 min rainfall intensity I₃₀ of 42 mm h^?1 generated a peak discharge of 3900 l s^?1 km^?2 in Bobcat Gulch. The same storm produced less than 5 l s^?1 km^?2 in Jug Gulch, due to less rainfall and the low watershed response. In the second summer, storms with, I₃₀ of 23 mm h^?1 and 32 mm h^?1 generated peak discharges of 1100 l s^?1 km^?2 and 1700 l s^?1 km^?2 in the treated and untreated watersheds respectively. Maximum water yield efficiencies were 10% and 17% respectively, but 18 of the 23 storms returned ≤2% of the rainfall as runoff, effectively obscuring interpretation of the erosion control treatments. I₃₀ explained 86% of the variability in peak discharges, 74% of the variability in storm runoff, and >80% of the variability in sediment yields. Maximum single‐storm sediment yields in the second summer were 370 kg ha^?1 in the treated watershed and 950 kg ha^?1 in the untreated watershed. Copyright © 2005 John Wiley & Sons, Ltd.     

The effect of truck traffic and road water content on sediment delivery from unpaved forest roads

A study investigated the effect of truck‐traffic intensity and road water‐content on the quality of runoff water from unsealed forest roads. Three sections of a gravel‐surfaced forest road were instrumented and exposed to low and high levels of truck traffic during wet winter conditions and dry summer conditions between July 2001 and December 2002. Rainfall, runoff, road moisture, and traffic were measured continuously, and suspended and bedload sediments were integrated measurements over 2‐week site‐service intervals. The median suspended sediment concentration from the three road segments under low truck‐traffic conditions (less than nine return truck passes prior to a storm) was 269 mg l^?1, increasing 2·7‐fold to a median of 725 mg l^?1 under high truck‐traffic conditions (greater than or equal to nine return truck passes prior to a storm). These concentrations, and increases due to traffic, are substantially less than most previously reported values. When these data are expressed as modified universal soil loss equation (MUSLE) erodibility values K, accounting for differences in rainfall energy, site characteristics and runoff, high traffic resulted in a road surface that was four times more erodible than the same road under low traffic conditions. Using multiple regression, traffic explained 36% of the variation in MUSLE erodibility, whereas road water content was not significant in the model. There was little difference in the erodibility of the road when trafficked in low water‐content compared with high water‐content conditions (MUSLE K values of 0·0084 versus 0·0080 respectively). This study shows that, for a good quality well‐maintained gravel forest road, the level of truck traffic affects the sediment concentration of water discharging from the road, whereas the water content of the road at the time of that traffic does not (note that traffic is not allowed during runoff events in Victoria). These conclusions are conditional upon the road being adequately maintained so that trafficking does not compromise the lateral drainage of the road profile. Copyright © 2005 John Wiley & Sons, Ltd.     

Solute concentrations of overland flow water in a cultivated field: spatial variations,intra‐ and inter‐storm trends

Major solute concentrations in overland flow water (OFW) were measured in an agricultural field of Brittany (western France). Two storm events were monitored in detail to examine the short time‐scale processes. During one year, samples were taken at different positions on the slope after each storm event to describe the spatial and seasonal variations of OFW chemistry. Although the total dissolved load in OFW is not much higher than in rain water, distinctive features are observed. K⁺, Ca²⁺, NH₄ , Cl⁻ and SOare the major solutes. The main origin of the elements (sea salts, exchangeable soil complex or fertilizers) determined most of the variations observed. Spatial variations along the slope are mainly seen for exchangeable cations, while seasonal variations are predominant for sea salts. Rainfall intensity and suspended sediment load induce strong differences between the two storm events studied in detail. However, the within‐storm variations and the seasonal monitoring show that this relationship is complex. Within‐storm variations suggest that, in addition to desorption processes, mixing with pre‐event water may occur. The lack of a relationship between sediment load and dissolved load is attributed to the high rate of the exchange processes, which has been checked by a simple experiment in vitro. It is concluded that the conditions of the transit of water on the field (velocity, length, status of the surface, crusted or not) may well play a major role in the chemical changes between rain water and OFW. The results suggest that vegetated buffer strips designed to reduce the sediment load only, and not the amount of overland flow, will have little effect on the transfer of dissolved pollutants to the watercourses. Copyright © 1999 John Wiley & Sons, Ltd.