Characterization of volcanic deposits with ground-penetrating radar

 Field-based studies of surficial volcanic deposits are commonly complicated by a combination of poor exposure and rapid lateral variations controlled by unknown paleotopography. The potential of ground-penetrating radar (GPR) as an aid to volcanological studies is shown using data collected from traverses over four well-exposed, Recent volcanic deposits in western Canada. The deposits comprise a pumice airfall deposit (3–4 m thick), a basalt lava flow (3–6 m thick), a pyroclastic flow deposit (15 m thick), and an internally stratified pumice talus deposit (60 m thick). Results show that GPR is effective in delineating major stratigraphic contacts and hence can be used to map unexposed deposits. Different volcanic deposits also exhibit different radar stratigraphic character, suggesting that deposit type may be determined from radar images. In addition, large blocks within the pyroclastic deposits are detected as distinctive point diffractor patterns in the profiles, showing that the technique has potential for providing important grain-size information in coarse poorly sorted deposits. Laboratory measurements of dielectric constant (K') are reported for samples of the main rock types and are compared with values of K' for the bulk deposit as inferred from the field data. The laboratory values differ significantly from the "field" values of K'; these results suggest that the effectiveness of GPR at any site can be substantially improved by initial calibration of well-exposed locations. Received: 10 May 1996 / Accepted: 27 December 1996     

Plinian and co-ignimbrite tephra fall from the

A study of pyroclastic deposits from the 1815 Tambora eruption reveals two distinct phases of activity, i.e., four initial tephra falls followed by generation of pyroclastic flows and the production of major co-ignimbrite ash fall. The first explosive event produced minor ash fall from phreatomagmatic explosions (F-1 layer). The second event was a Plinian eruption (F-2) correlated to the large explosion of 5 April 1815, which produced a column height of 33 km with an eruption rate of 1.1 × 10⁸ kg/s. The third event occurred during the lull in major activity from 5 to 10 April and produced minor ash fall (F-3). The fourth event produced a 43-km-high Plinian eruption column with an eruption rate of 2.8 × 10⁸ kg/s during the climax of activity on 10 April. Although very energetic, the Plinian events were of short duration (2.8 h each) and total erupted volume of the early (F-1 to F-4) fall deposits is only 1.8 km³ (DRE, dense rock equivalent). An abrupt change in style of activity occurred at end of the second Plinian event with onset of pyroclastic flow and surge generation. At least seven pyroclastic flows were generated, which spread over most of the volcano and Sanggar peninsula and entered the ocean. The volume of pyroclastic flow deposits on land is 2.6 km³ DRE. Coastal exposures show that pyroclastic flows entering the sea became highly fines depleted, resulting in mass loss of about 32%, in addition to 8% glass elutriation, as indicated by component fractionation. The subaqueous pyroclastic flows have thus lost about 40% of mass compared to the original erupted mixture. Pyroclastic flows and surges from this phase of the eruption are stratigraphically equivalent to a major ash fall deposit (F-5) present beyond the flow and surge zone at 40 km from the source and in distal areas. The F-5 fall deposit forms a larger proportion of the total tephra fall with increasing distance from source and represents about 80% of the total at a distance of 90 km and 92% of the total tephra fall from the 1815 eruption. The field relations indicate that the 20-km³ (DRE) F-5 deposit is a co-ignimbrite ash fall, generated largely during entrance of pyroclastic flows into the ocean. Based on the observed 40% fines depletion and component fractionation from the flows, the large volume of the F-5 co-ignimbrite ash requires eruption of 50 km³ (DRE, 1.4 × 10¹⁴ kg) pyroclastic flows.     

The occurrence of Mt Barca flank eruption in the evolution of the NW periphery of Etna volcano (Italy)

Geological surveys, tephrostratigraphic study, and ⁴⁰Ar/³⁹Ar age determinations have allowed us to chronologically constrain the geological evolution of the lower NW flank of Etna volcano and to reconstruct the eruptive style of the Mt Barca flank eruption. This peripheral sector of the Mt Etna edifice, corresponding to the upper Simeto valley, was invaded by the Ellittico volcano lava flows between 41 and 29 ka ago when the Mt Barca eruption occurred. The vent of this flank eruption is located at about 15 km away from the summit craters, close to the town of Bronte. The Mt Barca eruption was characterized by a vigorous explosive activity that produced pyroclastic deposits dispersed eastward and minor effusive activity with the emission of a 1.1-km-long lava flow. Explosive activity was characterized by a phreatomagmatic phase followed by a magmatic one. The geological setting of this peripheral sector of the volcano favors the interaction between the rising magma and the shallow groundwater hosted in the volcanic pile resting on the impermeable sedimentary basement. This process produced phreatomagmatic activity in the first phase of the eruption, forming a pyroclastic fall deposit made of high-density, poorly vesicular scoria lapilli and lithic clasts. Conversely, during the second phase, a typical strombolian fall deposit formed. In terms of hazard assessment, the possible occurrence of this type of highly explosive flank eruption, at lower elevation in the densely inhabited areas, increases the volcanic risk in the Etnean region and widens the already known hazard scenario.     

Eruptive conditions and depositional processes of Narbona Pass Maar volcano,Navajo volcanic field,Navajo Nation,New Mexico (USA)

Phreatomagmatic deposits at Narbona Pass, a mid-Tertiary maar in the Navajo volcanic field (NVF), New Mexico (USA), were characterized in order to reconstruct the evolution and dynamic conditions of the eruption. Our findings shed light on the temporal evolution of the eruption, dominant depositional mechanisms, influence of liquid water on deposit characteristics, geometry and evolution of the vent, efficiency of fragmentation, and the relative importance of magmatic and external volatiles. The basal deposits form a thick (5–20 m), massive lapilli tuff to tuff-breccia deposit. This is overlain by alternating bedded sequences of symmetrical to antidune cross-stratified tuff and lapilli tuff; and diffusely-stratified, clast-supported, reversely-graded lapilli tuffs that pinch and swell laterally. This sequence is interpreted to reflect an initial vent-clearing phase that produced concentrated pyroclastic density currents, followed by a pulsating eruption that produced multiple density currents with varying particle concentrations and flow conditions to yield the well-stratified deposits. Only minor localized soft-sediment deformation was observed, no accretionary lapilli were found, and grain accretion occurs on the lee side of dunes. This suggests that little to no liquid water existed in the density currents during deposition. Juvenile material is dominantly present as blocky fine ash and finely vesiculated fine to coarse lapilli pumice. This indicates that phreatomagmatic fragmentation was predominant, but also that the magma was volatile-rich and vesiculating at the time of eruption. This is the first study to document a significant magmatic volatile component in an NVF maar-diatreme eruption. The top of the phreatomagmatic sequence abruptly contacts the overlying minette lava flows, indicating no gradual drying-out period between the explosive and effusive phases. The lithology of the accidental clasts is consistent throughout the vertical pyroclastic stratigraphy, suggesting that the diatreme eruption did not penetrate below the base of the uppermost country rock unit, a sandstone aquifer ∼360 m thick. By comparison, other NVF diatremes several tens of kilometers away were excavated to depths of ∼1,000 m beneath the paleosurface (e.g., Delaney PT. Ship Rock, New Mexico: the vent of a violent volcanic eruption. In: Beus SS (ed) Geological society of America Centennial Field Guide, Rocky Mountain Section 2:411–415 (1987)). This can be accounted for by structurally controlled variations in aquifer thickness beneath different regions of the volcanic field. Variations in accidental clast composition and bedding style around the edifice are indicative of a laterally migrating or widening vent that encountered lateral variations in subsurface geology. We offer reasonable evidence that this subsurface lithology controlled the availability of external water to the magma, which in turn controlled characteristics of deposits and their distribution around the vent. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

GPR investigation of tephra fallout, Cerro Negro volcano, Nicaragua: a method for constraining parameters used in tephra sedimentation models

Most tephra fallout models rely on the advection–diffusion equation to forecast sedimentation and hence volcanic hazards. Here, we test the application of the advection–diffusion equation to tephra sedimentation using data collected on the proximal (350 to ~1,200?m from the vent) to medial (greater than ~1,200?m from the vent) tephra blanket of a basaltic cinder cone, Cerro Negro volcano, located in Nicaragua. Our understanding of tephra depositional processes at this volcano is significantly improved by combination of sample pit data in the medial zone and high-resolution ground-penetrating radar (GPR) data collected in the near vent and proximal zones. If the advection–diffusion equation applies, then the thickness of individual tephra deposits should have Gaussian crosswind profiles and exponential decay with distance away from the vent. At Cerro Negro, steady trade winds coupled with brief eruptions of relatively low energy (VEI 2–3) create relatively simple deposits. GPR data were collected along three crosswind profiles at distances of 700–1,600?m from the vent; sample pits were used to estimate thickness of the 1992 tephra deposit up to 13?km from the vent. Horizons identified in proximal GPR profiles exhibit Gaussian distributions with a high degree of statistical confidence, with diffusion coefficients of ~500?m²?s^?1 estimated for the deposits, confirming that the advection–diffusion equation is capable of modeling sedimentation in the proximal zone. The thinning trend downwind of the vent decreases exponentially from the cone base (350?m) to ~1,200?m from the vent. Beyond this distance, deposit overthickening occurs, identified in both GPR and sample pit datasets. The combined data reveal three depositional regimes: (1) a near-vent region on the cone itself, where fallout remobilizes in granular flows upon deposition; (2) a proximal zone in which particles fall from a height of less than ~2?km; and (3) a medial zone, in which particles fall from ~4 to 7?km and the deposit is thicker than expected based on thinning trends observed in the proximal zone of the deposit. This overthickening of the tephra blanket, defining the transition from proximal to medial depositional facies, is indicative of transition from sedimentation dominated by fallout from plume margins to that dominated by fallout from the buoyant eruption cloud—a feature of deposits previously identified in larger-volume eruptions. We interpret this change to represent a change in diffusion law, occurring at total particle fall times (the fall time threshold of numerical models) of ~400?s. Thus, the detailed GPR profiles and pit data collected at Cerro Negro help to validate current numerical models of tephra sedimentation.     

Post-depositional fracturing and subsidence of pumice flow deposits: Lascar Volcano,Chile

Unconsolidated pyroclastic flow deposits of the 1993 eruption of Lascar Volcano, Chile, have, with time, become increasingly dissected by a network of deeply penetrating fractures. The fracture network comprises orthogonal sets of decimeter-wide linear voids that form a pseudo-polygonal grid visible on the deposit surface. In this work, we combine shallow surface geophysical imaging tools with remote sensing observations and direct field measurements of the deposit to investigate these fractures and their underlying causal mechanisms. Based on ground penetrating radar images, the fractures are observed to have propagated to depths of up to 10 m. In addition, orbiting radar interferometry shows that deposit subsidence of up to 1 cm/year⁻¹ occurred between 1993 and 1996 with continued subsidence occurring at a slower rate thereafter. In situ measurements show that 1 m below the surface, the 1993 deposits remain 5°C to 15°C hotter, 18 years after emplacement, than adjacent deposits. Based on the observed subsidence as well as estimated cooling rates, the fractures are inferred to be the combined result of deaeration, thermal contraction, and sedimentary compaction in the months to years following deposition. Significant environmental factors, including regional earthquakes in 1995 and 2007, accelerated settling at punctuated moments in time. The spatially variable fracture pattern relates to surface slope and lithofacies variations as well as substrate lithology. Similar fractures have been reported in other ignimbrites but are generally exposed only in cross section and are often attributed to formation by external forces. Here we suggest that such interpretations should be invoked with caution, and deformation including post-emplacement subsidence and fracturing of loosely packed ash-rich deposits in the months to years post-emplacement is a process inherent in the settling of pyroclastic material.     

The Holocene Pucón eruption of Volcán Villarrica, Chile: deposit architecture and eruption chronology

The Pucón eruption was the largest Holocene explosive outburst of Volcán Villarrica, Chile. It discharged >1.0 km³ of basaltic-andesite magma and >0.8 km³ of pre-existing rock, forming a thin scoria-fall deposit overlain by voluminous ignimbrite intercalated with pyroclastic surge beds. The deposits are up to 70 m thick and are preserved up to 21 km from the present-day summit, post-eruptive lahar deposits extending farther. Two ignimbrite units are distinguished: a lower one (P1) in which all accidental lithic clasts are of volcanic origin and an upper unit (P2) in which basement granitoids also occur, both as free clasts and as xenoliths in scoria. P2 accounts for ∼80% of the erupted products. Following the initial scoria fallout phase, P1 pyroclastic flows swept down the northern and western flanks of the volcano, magma fragmentation during this phase being confined to within the volcanic edifice. Following a pause of at least a couple of days sufficient for wood devolatilization, eruption recommenced, the fragmentation level dropped to within the granitoid basement, and the pyroclastic flows of P2 were erupted. The first P2 flow had a highly turbulent front, laid down ignimbrite with large-scale cross-stratification and regressive bedforms, and sheared the ground; flow then waned and became confined to the southeastern flank. Following emplacement of pyroclastic surge deposits all across the volcano, the eruption terminated with pyroclastic flows down the northern flank. Multiple lahars were generated prior to the onset of a new eruptive cycle. Charcoal samples yield a probable eruption age of 3,510 ± 60 ¹⁴C years BP.     

Longitudinal structure of pyroclastic-flow deposits,revealed by GPR survey,at Merapi Volcano,Java, Indonesia

In 2006 Merapi volcano, Indonesia, erupted for a few months, producing several block-and-ash flows reaching a maximum distance of 7.5 km from the main vent. During the eruption, we conducted a survey on those flow deposits in the Gendol Valley at Kaliadem village, about 4.5 km from the Merapi submit, using a Ground Penetrating Radar (GPR). The upper deposit was studied in its distal reaches, whereas the one below was studied in its medial reaches. The field study was carried out with a commercial RAMAC® GPR coupled with 100 MHz antennas, and the data treatment conducted with Reflex™ software. From this survey, we determined both deposits' local (1) thickness – reaching a maximum of 15 m – and (2) internal architecture. This last one is governed by long reflecting horizons extending over 20 to 30 m that delimit layers showing progradation patterns in their distal reaches. Within these layers we could also observe an internal architecture of still unknown origin. The layers are interpreted as the result of the flow pulses that progressively deposited downstream-ward by progradation. However the interpretation of those GPR profiles is a bit hazardous, because of the absence of outcrops, and we can only proceed by analogy with other studies. Nevertheless, despite numerous limitations, GPR is a helpful tool to understand pyroclastic deposits' structure when no visual observations are available.     

Coupling eruption and tsunami records: the Krakatau 1883 case study,Indonesia

The well-documented 1883 eruption of Krakatau volcano (Indonesia) offers an opportunity to couple the eruption’s history with the tsunami record. The aim of this paper is not to re-analyse the scenario for the 1883 eruption but to demonstrate that the study of tsunami deposits provides information for reconstructing past eruptions. Indeed, though the characteristics of volcanogenic tsunami deposits are similar to those of other tsunami deposits, they may include juvenile material (e.g. fresh pumice) or be interbedded with distal pyroclastic deposits (ash fall, surges), due to their simultaneity with the eruption. Five kinds of sedimentary and volcanic facies related to the 1883 events were identified along the coasts of Java and Sumatra: (1) bioclastic tsunami sands and (2) pumiceous tsunami sands, deposited respectively before and during the Plinian phase (26–27 August); (3) rounded pumice lapilli reworked by tsunami; (4) pumiceous ash fall deposits and (5) pyroclastic surge deposits (only in Sumatra). The stratigraphic record on the coasts of Java and Sumatra, which agrees particularly well with observations of the 1883 events, is tentatively linked to the proximal stratigraphy of the eruption.     

Volcanic stratigraphy of large-volume silicic pyroclastic eruptions during Oligocene Afro-Arabian flood volcanism in Yemen

A new stratigraphy for bimodal Oligocene flood volcanism that forms the volcanic plateau of northern Yemen is presented based on detailed field observations, petrography and geochemical correlations. The >1 km thick volcanic pile is divided into three phases of volcanism: a main basaltic stage (31 to 29.7 Ma), a main silicic stage (29.7 to 29.5 Ma), and a stage of upper bimodal volcanism (29.5 to 27.7 Ma). Eight large-volume silicic pyroclastic eruptive units are traceable throughout northern Yemen, and some units can be correlated with silicic eruptive units in the Ethiopian Traps and to tephra layers in the Indian Ocean. The silicic units comprise pyroclastic density current and fall deposits and a caldera-collapse breccia, and they display textures that unequivocally identify them as primary pyroclastic deposits: basal vitrophyres, eutaxitic fabrics, glass shards, vitroclastic ash matrices and accretionary lapilli. Individual pyroclastic eruptions have preserved on-land volumes of up to ∼850 km³. The largest units have associated co-ignimbrite plume ash fall deposits with dispersal areas >1×10⁷ km² and estimated maximum total volumes of up to 5,000 km³, which provide accurate and precisely dated marker horizons that can be used to link litho-, bio- and magnetostratigraphy studies. There is a marked change in eruption style of silicic units with time, from initial large-volume explosive pyroclastic eruptions producing ignimbrites and near-globally distributed tuffs, to smaller volume (<50 km³) mixed effusive-explosive eruptions emplacing silicic lavas intercalated with tuffs and ignimbrites. Although eruption volumes decrease by an order of magnitude from the first stage to the last, eruption intervals within each phase remain broadly similar. These changes may reflect the initiation of continental rifting and the transition from pre-break-up thick, stable crust supporting large-volume magma chambers, to syn-rift actively thinning crust hosting small-volume magma chambers.Electronic Supplementary Material Supplementary material is available for this article at     

The Ottaviano eruption of Somma-Vesuvio (8000 y B.P.): a magmatic alternating fall and flow-forming eruption

The Ottaviano eruption occurred in the late neolithic (8000 y B.P.). 2.40 km³ of phonolitic pyroclastic material (0.61 km³ DRE) were emplaced as pyroclastic flow, surge and fall deposits. The eruption began with a fall phase, with a model column height of 14 km, producing a pumice fall deposit (LA). This phase ended with short-lived weak explosive activity, giving rise to a fine-grained deposit (L1), passing to pumice fall deposits as the result of an increasing column height and mass discharge rate. The subsequent two fall phases (producing LB and LC deposits), had model column heights of 20 and 22 km with eruption rates of 2.5 × 10⁷ and 2.81 × 10⁷ kg/s, respectively. These phases ended with the deposition of ash layers (L2 and L3), related to a decreasing, pulsing explosive activity. The values of dynamic parameters calculated for the eruption classify it as a sub-plinian event. Each fall phase was characterized by variations in the eruptive intensity, and several pyroclastic flows were emplaced (F1 to F3). Alternating pumice and ash fall beds record the waning of the eruption. Finally, owing to the collapse of a eruptive column of low gas content, the last pyroclastic flow (F4) was emplaced.     

The Holocene Secche di Lazzaro phreatomagmatic succession (Stromboli,Italy): evidence of pyroclastic density current origin deduced by facies analysis and AMS flow directions

The edifice of Stromboli volcano gravitationally collapsed several times during its volcanic history (>100 ka–present). The largest Holocene event occurred during the final stage of the Neostromboli activity (∼13–5 ka), and was accompanied by the emplacement of phreatomagmatic and lahar deposits, known as the Secche di Lazzaro succession. A stratigraphic and paleomagnetic study of the Secche di Lazzaro deposits allows the interpretation of the emplacement and the eruptive processes. We identify three main units within the succession that correspond to changing eruption conditions. The lower unit (UA) consists of accretionary lapilli-rich, thinly bedded, parallel- to cross-stratified ash deposits, interpreted to indicate the early stages of the eruption and emplacement of dilute pyroclastic density currents. Upward, the second unit (UB) of the deposit is more massive and the beds thicker, indicating an increase in the sedimentation rate from pyroclastic density currents. The upper unit (UC) caps the succession with thick, immediately post-eruptive lahars, which reworked ash deposited on the volcano’s slope. Flow directions obtained by Anisotropy of Magnetic Susceptibility (AMS) analysis of the basal bed of UA at the type locality suggest a provenance of pyroclastic currents from the sea. This is interpreted to be related to the initial base-surges associated with water–magma interaction that occurred immediately after the lateral collapse, which wrapped around the shoulder of the sector collapse scar. Upward in the stratigraphy (upper beds of UA and UB) paleoflow directions change and show a provenance from the summit vent, probably related to the multiple collapses of a vertical, pulsatory eruptive column.     

Variability in eruptive dynamics associated with caldera collapse: an example from two successive eruptions at Batur volcanic field,Bali, Indonesia

Batur volcanic field (BVF) in Bali, Indonesia, underwent two successive caldera-forming eruptions, CI and CII (29,300 and 20,150 years b.p., respectively) that resulted in the deposition of dacitic ignimbrites. The respective ignimbrites show contrasted stratigraphies, exemplify the variability of dynamics associated with caldera-forming eruptions and provide insights into the possible controls exerted by caldera collapse mechanisms. The Ubud Ignimbrite is widespread and covers most of southern Bali. The deposits consist dominantly of pyroclastic flow with minor pumice fall deposits. The intra-caldera succession comprises three distinct, partially to densely welded cooling units separated by non-welded pyroclastic flow and fall deposits. The three cooling units consist of pyroclastic flow deposits only and together represent up to 16 distinct flow units, each including a thin, basal, lithic-rich breccia. This eruption was related to a 13.5×10 km caldera (CI) with a minimum collapsed volume of 62 km³. The floor of caldera CI is inferred to have a piecemeal geometry. The Ubud Ignimbrite is interpreted as the product of a relatively long-lasting, pulsating, collapsing fountain that underwent at least two time breaks. A stable column developed during the second time break. Discharge rate was high overall, but oscillatory, and increased toward the end of the eruption. These dynamics are thought to reflect sequential collapse of the CI structure. The Gunungkawi Ignimbrite is of more limited extent outside the source caldera and occurs only in central southern Bali. The Gunungkawi Ignimbrite proximal deposits consist of interbedded accretionary lapilli-bearing ash surge, ash fall, pumice lapilli fall and thin pyroclastic flow deposits, overlain by a thick and massive pyroclastic flow deposit with a thick basal lag breccia. The caldera (CII) is 7.5×6 km in size, with a minimum collapsed volume of 9 km³. The CII eruption included two distinct phases. During the first, eruption intensity was low to moderate and an unstable, essentially phreatomagmatic column developed. During the second phase, the onset of caldera collapse drastically increased the eruption intensity, resulting in column collapse. The caldera floor is believed to have subsided rapidly, producing a single, short-lived burst of high eruption intensity that resulted in the deposition of the uppermost massive pyroclastic flow.Editorial responsibility: T. Druitt     

Stratigraphy,chronology, and character of the 1976 pyroclastic eruption of Augustine volcano,Alaska

The chronology of deposits of the 1976 eruption of Augustine volcano, which produced pyroclastic falls, pyroclastic flows, and lava domes, is determined by correlating the stratigraphy with published records of seismicity, plume observations, and distant ash falls. Three thin air-fall ash beds (unit A1, A2 and A3) correlate with events near the beginning of the 1976 eruption on 22 and 23 January. On 24 January a small-volume, ash-cloud-surge deposit (unit S) accumulated over the north half of Augustine Island. A series of pumiceous pyroclastic flows represented by the lobate pumiceous deposits (unit F) occurred on 24 January and locally melted the snowpack to cause small pumice-laden floods. A thin ash bed (unit A4) was deposited on 24 January, and the main plinian eruption (unit P) occurred on 25 January. In middle to late February and again in mid April, lava domes were extruded at the summit accompanied by incandescent block-and-ash flows down the north flank. A hut near the north coast of the island was mechanically and thermally damaged by the small-volume ash-cloud surge of unit S before the eruption of the pumice flow of unit F; the metal roof was then penetrated by lithic fragments of the plinian fall of 25 January. Explosive eruptions in the early stage of an eruption-like that which deposited unit S — are important hazards at Augustine Island, as are infrequent debris avalanches and attendant tsunamis.deceased on 18 May 1980     

New insights into Late Pleistocene explosive volcanic activity and caldera formation on Ischia (southern Italy)

A new pyroclastic stratigraphy is presented for the island of Ischia, Italy, for the period ∼75–50 ka BP. The data indicate that this period bore witness to the largest eruptions recorded on the island and that it was considerably more volcanically active than previously thought. Numerous vents were probably active during this period. The deposits of at least 10 explosive phonolite to basaltic-trachyandesite eruptions are described and interpreted. They record a diverse range of explosive volcanic activity including voluminous fountain-fed ignimbrite eruptions, fallout from sustained eruption columns, block-and-ash flows, and phreatomagmatic eruptions. Previously unknown eruptions have been recognised for the first time on the island. Several of the eruptions produced pyroclastic density currents that covered the whole island as well as the neighbouring island of Procida and parts of the mainland. The morphology of Ischia was significantly different to that seen today, with edifices to the south and west and a submerged depression in the centre. The largest volcanic event, the Monte Epomeo Green Tuff (MEGT) resulted in caldera collapse across all or part of the island. It is shown to comprise at least two thick intracaldera ignimbrite flow-units, separated by volcaniclastic sediments that were deposited during a pause in the eruption. Extracaldera deposits of the MEGT include a pumice fall deposit emplaced during the opening phases of the eruption, a widespread lithic lag breccia outcropping across much of Ischia and Procida, and a distal ignimbrite in south-west Campi Flegrei. During this period the style and magnitude of volcanism was dictated by the dynamics of a large differentiated magma chamber, which was partially destroyed during the MEGT eruption. This contrasts with the small-volume Holocene and historical effusive and explosive activity on Ischia, the timing and distribution of which has been controlled by the resurgence of the Monte Epomeo block. The new data contribute to a clearer understanding of the long-term volcanic and magmatic evolution of Ischia.     

Deep explosive focal depths during maar forming magmatic-hydrothermal eruption: Baccano Crater,Central Italy

We describe the eruptive activity of the Pleistocene composite Baccano maar crater in the Sabatini Volcanic Complex (Central Italy) combining stratigraphy, grain size/componentry and rare earth element and Yttrium (REY) composition of its eruptive products with the stratigraphy and geothermal data derived from deep wells drilled on the Baccano structural high. The main lithological characteristics of the basal Baccano maar pyroclastic deposit, composed of more than 60% wt of non-thermometamorphosed lithic clasts from the sedimentary basement, show that the first eruption was magmatic-hydrothermal in nature. The lithology of the sedimentary lithic clasts indicates that the fragmentation level was at a depth of −1,000 to −1,200 m, with fragment depth verified by deep well stratigraphy. The 15% wt juvenile non-vesicular glass components suggest that magma played a minor role in powering the eruption. Assuming that the high-salinity hot hydrothermal fluids (365<T<410°C and P∼25 MPa), hosted in the highly permeable and confined aquifer below the Baccano maar are representative of those at the time of the eruption, we propose that hydrofracturing would have triggered the eruption caused by overpressure at the top of the geothermal aquifer. REY analysis performed on pyroclastic fragments and basement rocks suggest that partial dissolution of the deeper limestones (>−1,400 m) by the aggressive hydrothermal fluids enriched in acid components (HF, HCl, and H2SO4) may have contributed to increased CO₂ partial pressure that helped to drive the hydrofracturing. This could have caused rapid vapour separation and pressure drop, allowing the almost simultaneous breaking of the aquifer cover and brecciation of the calcareous units down to −1,000 to −1,200 m depth. The relative abundance of calcareous lithics in the basal part of the first Baccano eruptive unit, representing about the upper 200 m of stratigraphy below the top of the Baccano structural high, reveals the descent of the piezometric surface during the eruption. Combining deep well information and maar product stratigraphy, using also REY data from maar pyroclastic fragments and the basement rocks we draw an interpretative model for the Baccano maar-forming eruption, concluding that a) magmatic-hydrothermal eruptions may originate deeper than previously thought, and b) hydrothermal fluids circulating in limestone aquifers may play an important role in triggering such eruptions.     

Geology of the Side Crater of the Erebus volcano,Antarctica

The summit cone of the Erebus volcano contains two craters. The Main crater is roughly circular (∼ 500 m diameter) and contains an active persistent phonolite lava lake ∼ 200 m below the summit rim. The Side Crater is adjacent to the southwestern rim of the Main Crater. It is a smaller spoon-shaped Crater (250–350 m diameter, 50–100 m deep) and is inactive. The floor of the Side Crater is covered by snow/ice, volcanic colluvium or weakly developed volcanic soil in geothermal areas (a.k.a. warm ground). But in several places the walls of the Side Crater provide extensive vertical exposure of rock which offers an insight into the recent eruptive history of Erebus. The deposits consist of lava flows with subordinate volcanoclastic lithologies. Four lithostratigraphic units are described: SC 1 is a compound lava with complex internal flow fabrics; SC 2 consists of interbedded vitric lavas, autoclastic and pyroclastic breccias; SC 3 is a thick sequence of thin lavas with minor autoclastic breccias; SC 4 is a pyroclastic fall deposit containing large scoriaceous lava bombs in a matrix composed primarily of juvenile lapilli-sized pyroclasts. Ash-sized pyroclasts from SC 4 consist of two morphologic types, spongy and blocky, indicating a mixed strombolian-phreatomagmatic origin. All of the deposits are phonolitic and contain anorthoclase feldspar.     

The Taurewa Eruptive Episode: evidence for climactic eruptions at Ruapehu volcano, New Zealand

 The ca. 10,500 years B.P. eruptions at Ruapehu volcano deposited 0.2–0.3 km³ of tephra on the flanks of Ruapehu and the surrounding ring plain and generated the only known pyroclastic flows from this volcano in the late Quaternary. Evidence of the eruptions is recorded in the stratigraphy of the volcanic ring plain and cone, where pyroclastic flow deposits and several lithologically similar tephra deposits are identified. These deposits are grouped into the newly defined Taurewa Formation and two members, Okupata Member (tephra-fall deposits) and Pourahu Member (pyroclastic flow deposits). These eruptions identify a brief (<ca. 2000-year) but explosive period of volcanism at Ruapehu, which we define as the Taurewa Eruptive Episode. This Episode represents the largest event within Ruapehu's ca. 22,500-year eruptive history and also marks its culmination in activity ca. 10,000 years B.P. Following this episode, Ruapehu volcano entered a ca. 8000-year period of relative quiescence. We propose that the episode began with the eruption of small-volume pyroclastic flows triggered by a magma-mingling event. Flows from this event travelled down valleys east and west of Ruapehu onto the upper volcanic ring plain, where their distal remnants are preserved. The genesis of these deposits is inferred from the remanent magnetisation of pumice and lithic clasts. We envisage contemporaneous eruption and emplacement of distal pumice-rich tephras and proximal welded tuff deposits. The potential for generation of pyroclastic flows during plinian eruptions at Ruapehu has not been previously considered in hazard assessments at this volcano. Recognition of these events in the volcanological record is thus an important new factor in future risk assessments and mitigation of volcanic risk at Tongariro Volcanic Centre. Received: 5 July 1998 / Accepted: 12 March 1999     

Deposits of the 30 March 1956 directed blast at Bezymianny volcano,Kamchatka, Russia

 On 30 March 1956 a catastrophic directed blast took place at Bezymianny volcano. It was caused by the failure of 0.5 km³ portion of the volcanic edifice. The blast was generated by decompression of intra-crater dome and cryptodome that had formed during the preclimactic stage of the eruption. A violent pyroclastic surge formed as a result of the blast and spread in an easterly direction effecting an area of 500 km² on the lower flank of the volcano. The thickness of the deposits, although variable, decreases with distance from the volcano from 2.5 m to 4 cm. The volume of the deposit is calculated to be 0.2–0.4 km³. On average, the deposits are 84% juvenile material (andesite), of which 55% is dense andesite and 29% vesicular andesite. On a plot of sorting vs median diameter (Inman coefficients) the deposits occupy the area between the fall and flow fields. In the proximal zone (less than 19 km from the volcano) three layers can be distinguished in the deposits. The lower one (layer A) is distributed all over the proximal area, is very poorly sorted, enriched in fragments of dense juvenile andesite and contains an admixture of soil and uncharred plant remains. The middle layer (layer B) is distributed in patches tens to hundreds of metres across on the surface of layer A. Layer B is relatively well sorted as a result of a very low content of fine fractions, and it contains rare charred plant remains. The uppermost layer (layer C) forms still smaller patches on the surface of layer B. Layer C is characterized by intermediate sorting, is enriched in vesicular juvenile andesitic fragments, and contains a high percentage of the fine fraction and very rare plant remains which are thoroughly charred. Maximum clast size decreases from layer A to layer C. The absence of internal cross bedding is a characteristic of all three layers. In the distal zone (more than 19 km from the volcano) stratigraphy changes abruptly. Deposit here consists of one layer 26 to 4 cm in thickness, is composed of wavy laminated sand with a touch of gravel, is well sorted and contains uncharred plant remains. The Bezymianny blast deposits are not analogous with known types of pyroclastic surges, with the exception of the directed blast deposits of the Mount St.Helens eruption of 18 May 1980. The peculiarities of deposits from these two eruptions allow them to be separated into a special type: blast surge. This type of surge is formed when failure of volcanic edifice relieves the pressure from an inter-crater dome and/or cryptodome. A model is proposed to explain the peculiarities of the formation, transportation and emplacement of the Bezymianny blast surge deposits. Received: 19 December 1994 / Accepted: 12 December 1995     

The AD 1362 Öræfajökull eruption,S.E. Iceland: Physical volcanology and volatile release

The explosive rhyolitic eruption of Öræfajökull volcano, Iceland, in AD 1362 is described and interpreted based on the sequence of pyroclastic fall and flow deposits at 10 proximal locations around the south side of the volcano. Öræfajökull is an ice-clad stratovolcano in south central Iceland which has an ice-filled caldera (4–5 km diameter) of uncertain origin. The main phase of the eruption took place over a few days in June and proceeded in three main phases that produced widely dispersed fallout deposits and a pyroclastic flow deposit. An initial phase of phreatomagmatic eruptive activity produced a volumetrically minor, coarse ash fall deposit (unit A) with a bi-lobate dispersal. This was followed by a second phreatomagmatic, possibly phreatoplinian, phase that deposited more fine ash beds (unit B), dispersed to the SSE. Phases A and B were followed by an intense, climactic Plinian phase that lasted ∼ 8–12 h and produced unit C, a coarse-lapilli, pumice-clast-dominated fall deposit in the proximal region. At the end of Plinian activity, pyroclastic flows formed a poorly-sorted deposit, unit D, presently of very limited thickness and exposed distribution. Much of Eastern Iceland is covered with a very fine distal ash layer, dispersed to the NE. This was probably deposited from an umbrella cloud and is the distal representation of the Plinian fallout. A total bulk fall deposit volume of ∼ 2.3 km³ is calculated (∼ 1.2 km³ DRE). Pyroclastic flow deposit volumes have been crudely estimated to be < 0.1 km³. Maximum clast size data interpreted by 1-D models suggests an eruption column ∼ 30 km high and mass discharge rates of ∼ 10⁸ kg s^− 1. Ash fall may have taken place from heights around 15 km, above the local tropopause (∼ 10 km), with coarser clasts dispersed below that under a different wind regime. Analyses of glass inclusions and matrix glasses suggest that the syn-eruptive SO₂ release was only ∼ 1 Mt. This result is supported by published Greenland ice-core acidity peak data that also suggest very minor sulphate deposition and thus SO₂ release. The small sulphur release reflects the low sulphur solubility in the 1362 rhyolitic melt. The low tropopause over Iceland and the 30-km-high eruption column certainly led to stratospheric injection of gas and ash but little sulphate aerosol was generated. Moreover, pre-eruptive and degassed halogen concentrations (Cl, F) indicate that these volatiles were not efficiently released during the eruption. Besides the local pyroclastic flow (and related lahar) hazard, the impact of the Öræfajökull 1362 eruption was perhaps restricted to widespread ash fall across Eastern Iceland and parts of northern Europe.