Quantitative detection of fluid distribution using time-lapse seismic

Although previous seismic monitoring studies have revealed several relationships between seismic responses and changes in reservoir rock properties, the quantitative evaluation of time‐lapse seismic data remains a challenge. In most cases of time‐lapse seismic analysis, fluid and/or pressure changes are detected qualitatively by changes in amplitude strength, traveltime and/or Poisson's ratio. We present the steps for time‐lapse seismic analysis, considering the pressure effect and the saturation scale of fluids. We then demonstrate a deterministic workflow for computing the fluid saturation in a reservoir in order to evaluate time‐lapse seismic data. In this approach, we derive the physical properties of the water‐saturated sandstone reservoir, based on the following inputs: V_P, V_S, ρ and the shale volume from seismic analysis, the average properties of sand grains, and formation‐water properties. Next, by comparing the in‐situ fluid‐saturated properties with the 100% formation‐water‐saturated reservoir properties, we determine the bulk modulus and density of the in‐situ fluid. Solving three simultaneous equations (relating the saturations of water, oil and gas in terms of the bulk modulus, density and the total saturation), we compute the saturation of each fluid. We use a real time‐lapse seismic data set from an oilfield in the North Sea for a case study.     

Seismic driven probabilistic classification of reservoir facies for static reservoir modelling: a case history in the Barents Sea

In this paper we present a case history of seismic reservoir characterization where we estimate the probability of facies from seismic data and simulate a set of reservoir models honouring seismically‐derived probabilistic information. In appraisal and development phases, seismic data have a key role in reservoir characterization and static reservoir modelling, as in most of the cases seismic data are the only information available far away from the wells. However seismic data do not provide any direct measurements of reservoir properties, which have then to be estimated as a solution of a joint inverse problem. For this reason, we show the application of a complete workflow for static reservoir modelling where seismic data are integrated to derive probability volumes of facies and reservoir properties to condition reservoir geostatistical simulations. The studied case is a clastic reservoir in the Barents Sea, where a complete data set of well logs from five wells and a set of partial‐stacked seismic data are available. The multi‐property workflow is based on seismic inversion, petrophysics and rock physics modelling. In particular, log‐facies are defined on the basis of sedimentological information, petrophysical properties and also their elastic response. The link between petrophysical and elastic attributes is preserved by introducing a rock‐physics model in the inversion methodology. Finally, the uncertainty in the reservoir model is represented by multiple geostatistical realizations. The main result of this workflow is a set of facies realizations and associated rock properties that honour, within a fixed tolerance, seismic and well log data and assess the uncertainty associated with reservoir modelling.     

Bayesian inversion of time‐lapse seismic data for the estimation of static reservoir properties and dynamic property changes

Seismic conditioning of static reservoir model properties such as porosity and lithology has traditionally been faced as a solution of an inverse problem. Dynamic reservoir model properties have been constrained by time‐lapse seismic data. Here, we propose a methodology to jointly estimate rock properties (such as porosity) and dynamic property changes (such as pressure and saturation changes) from time‐lapse seismic data. The methodology is based on a full Bayesian approach to seismic inversion and can be divided into two steps. First we estimate the conditional probability of elastic properties and their relative changes; then we estimate the posterior probability of rock properties and dynamic property changes. We apply the proposed methodology to a synthetic reservoir study where we have created a synthetic seismic survey for a real dynamic reservoir model including pre‐production and production scenarios. The final result is a set of point‐wise probability distributions that allow us to predict the most probable reservoir models at each time step and to evaluate the associated uncertainty. Finally we also show an application to real field data from the Norwegian Sea, where we estimate changes in gas saturation and pressure from time‐lapse seismic amplitude differences. The inverted results show the hydrocarbon displacement at the times of two repeated seismic surveys.     

Forced imbibition into a limestone: measuring P‐wave velocity and water saturation dependence on injection rate

Quantitative interpretation of time‐lapse seismic data requires knowledge of the relationship between elastic wave velocities and fluid saturation. This relationship is not unique but depends on the spatial distribution of the fluid in the pore‐space of the rock. In turn, the fluid distribution depends on the injection rate. To study this dependency, forced imbibition experiments with variable injection rates have been performed on an air‐dry limestone sample. Water was injected into a cylindrical sample and was monitored by X‐Ray Computed Tomography and ultrasonic time‐of‐flight measurements across the sample. The measurements show that the P‐wave velocity decreases well before the saturation front approaches the ultrasonic raypath. This decrease is followed by an increase as the saturation front crosses the raypath. The observed patterns of the acoustic response and water saturation as functions of the injection rate are consistent with previous observations on sandstone. The results confirm that the injection rate has significant influence on fluid distribution and the corresponding acoustic response. The complexity of the acoustic response —‐ that is not monotonic with changes in saturation, and which at the same saturation varies between hydrostatic conditions and states of dynamic fluid flow – may have implications for the interpretation of time‐lapse seismic responses.     

Rock physics modelling and inversion for saturation-pressure changes in time-lapse seismic studies

Time-lapse seismic data are generally used to monitor the changes in dynamic reservoir properties such as fluid saturation and pore or effective pressure. Changes in saturation and pressure due to hydrocarbon production usually cause changes in the seismic velocities and as a consequence changes in seismic amplitudes and travel times. This work proposes a new rock physics model to describe the relation between saturation-pressure changes and seismic changes and a probabilistic workflow to quantify the changes in saturation and pressure from time-lapse seismic changes. In the first part of this work, we propose a new quadratic approximation of the rock physics model. The novelty of the proposed formulation is that the coefficients of the model parameters (i.e. the saturation-pressure changes) are functions of the porosity, initial saturation and initial pressure. The improvements in the results of the forward model are shown through some illustrative examples. In the second part of the work, we present a Bayesian inversion approach for saturation-pressure 4D inversion in which we adopt the new formulation of the rock physics approximation. The inversion results are validated using synthetic pseudo-logs and a 3D reservoir model for CO₂ sequestration.     

Sensitivity analysis and application of time‐lapse full‐waveform inversion: synthetic testing and field data example from the North Sea,Norway

Time‐lapse refraction can provide complementary seismic solutions for monitoring subtle subsurface changes that are challenging for conventional P‐wave reflection methods. The utilization of refraction time lapse has lagged behind in the past partly due to the lack of robust techniques that allow extracting easy‐to‐interpret reservoir information. However, with the recent emergence of the full‐waveform inversion technique as a more standard tool, we find it to be a promising platform for incorporating head waves and diving waves into the time‐lapse framework. Here we investigate the sensitivity of 2D acoustic, time‐domain, full‐waveform inversion for monitoring a shallow, weak velocity change (?30 m/s, or ?1.6%). The sensitivity tests are designed to address questions related to the feasibility and accuracy of full‐waveform inversion results for monitoring the field case of an underground gas blowout that occurred in the North Sea. The blowout caused the gas to migrate both vertically and horizontally into several shallow sand layers. Some of the shallow gas anomalies were not clearly detected by conventional 4D reflection methods (i.e., time shifts and amplitude difference) due to low 4D signal‐to‐noise ratio and weak velocity change. On the other hand, full‐waveform inversion sensitivity analysis showed that it is possible to detect the weak velocity change with the non‐optimal seismic input. Detectability was qualitative with variable degrees of accuracy depending on different inversion parameters. We inverted, the real 2D seismic data from the North Sea with a greater emphasis on refracted and diving waves’ energy (i.e., most of the reflected energy was removed for the shallow zone of interest after removing traces with offset less than 300 m). The full‐waveform inversion results provided more superior detectability compared with the conventional 4D stacked reflection difference method for a weak shallow gas anomaly (320 m deep).     

有效压力与饱和度变化的气藏多波时移地震AVO响应

天然气在开发过程中,储层有效压力和含气饱和度均会发生变化,研究有效压力和含气饱和度的变化对地震响应特征的影响,在基于时移地震的剩余气分布预测研究中具有重要意义。天然气和石油的声学性质有着明显的差异,油藏时移地震的研究成果不能直接应用于气藏,因此需要开展气藏的时移地震研究。利用Shapiro模型表征干岩石弹性模量随有效压力的变化,借助Batzle-Wang方程描述流体速度随压力的变化关系,联合Gassmann理论进行流体替代,表征饱和流体岩石速度随含气饱和度的变化,建立了饱和流体岩石速度随有效压力和饱和度变化的岩石物理模型。基于该模型,对不同含气饱和度和不同有效压力下的气藏储层模型进行了多波时移地震叠前振幅变化（AVO）模拟。结果表明多波时移地震AVO技术可以有效地区分有效压力变化和含气饱和度变化,为进一步开展气藏多波时移地震流体监测提供了理论参考依据。      

Estimation of petrophysical parameters by linearized inversion of angle domain pre-stack data

We describe a linear Bayesian inversion method to estimate the relevant petrophysical properties of the media forming a reflecting interface from the observations of amplitude variation with incidence angle. Three main steps characterize the proposed approach:
– information from borehole logs are statistically analysed to estimate the empirical models that describe the functional relationship between petrophysical (e.g. porosity, saturation, pressure or depth) and seismic variable(P and S velocities and density);
– the pure-mode (PP) reflection coefficient is parameterized in terms of the relevant petrophysical variables and is linearized in order to implement the linear inversion;
– the sought petrophysical parameters are estimated from the seismic reflected amplitudes by applying the linearized inversion where a priori information, data and model errors and solutions are described by probability density functions.
We test the method on synthetic and real data relative to reflections from a shale/gas-sand interface where the amplitude versus angle response, besides the lithological contrast, is mainly controlled by the saturation and porosity of the sand layer. The outcomes of the linearized inversion are almost identical to those obtained by a previously developed non-linear inversion method demonstrating the applicability of the linear inversion. It turns out that the gas-sand saturation in the range 0%–95% is a poorly resolved parameter while the porosity is the best resolved parameter. The issues of robustness and resolution of the inversion are discussed either through singular value decomposition analysis or the observation of the a posteriori probability density functions.
The linear inversion algorithm, compared with the previously developed non-linear method, reduces significantly the computation time allowing for more extensive applications.     

Stochastic inversion of pressure and saturation changes from time-lapse multi component data

Knowledge about saturation and pressure distributions in a reservoir can help in determining an optimal drainage pattern, and in deciding on optimal well designs to reduce risks of blow‐outs and damage to production equipment. By analyzing time‐lapse PP AVO or time‐lapse multicomponent seismic data, it is possible to separate the effects of production related saturation and pressure changes on seismic data. To be able to utilize information about saturation and pressure distributions in reservoir model building and simulation, information about uncertainty in the estimates is useful. In this paper we present a method to estimate changes in saturation and pressure from time‐lapse multicomponent seismic data using a Bayesian estimation technique. Results of the estimations will be probability density functions (pdfs), giving immediate information about both parameter values and uncertainties. Linearized rock physical models are linked to the changes in saturation and pressure in the prior probability distribution. The relationship between the elastic parameters and the measured seismic data is described in the likelihood model. By assuming Gaussian distributed prior uncertainties the posterior distribution of the saturation and pressure changes can be calculated analytically. Results from tests on synthetic seismic data show that this method produces more precise estimates of changes in effective pressure than a similar methodology based on only PP AVO time‐lapse seismic data. This indicates that additional information about S‐waves obtained from converted‐wave seismic data is useful for obtaining reliable information about the pressure change distribution.     

Quantitative pore-type characterization from well logs based on the seismic petrophysics in a carbonate reservoir

Quality, availability and consistency of the measured and interpreted well log data are essential in the seismic reservoir characterization methods, and seismic petrophysics is the recommended workflow to achieve data consistency between logs and seismic domains. This paper uses seismic petrophysics workflow to improve well logs and pore geometry interpretations for an oil carbonate reservoir in the Fahliyan Formation in the southwest of Iran. The petrophysical interpreted well logs, rock physics and well-to-seismic tie analysis are integrated into the proposed workflow. Our implementation incorporates revising petrophysical well log interpretations and updating pore geometry characteristics to obtain a better well-tie quality. We first propose an improved pore-type characterization approach based on both P- and S-wave velocities for quantifying pore geometry. Then, seismic logs are estimated accordingly, and the results are used in the well-to-seismic analysis. The quality of the well-tie is improved, furthermore, by iterating on the petrophysical interpreted well logs as well as the calculated pore geometries. For the intervals with high-quality data, our workflow improves the consistency between the results of measured and modelled seismic logs. For the intervals with problematic well logs, the application of our proposed workflow results in the successful replacement of the poor data and subsequently leads to an improved wavelet estimation and well-tie results. In both cases, a higher quantification of pore geometries is achieved, which in turn is confirmed by the core images and formation micro-imager analysis.     

Petrophysical inversion of AVA data

We investigate the interactions between the elastic parameters, V_P, V_S and density, estimated by non-linear inversion of AVA data, and the petrophysical parameters, depth (pressure), porosity, clay content and fluid saturation, of an actual gas-bearing reservoir. In particular, we study how the ambiguous solutions derived from the non-uniqueness of the seismic inversion affect the estimates of relevant rock properties. It results that the physically admissible values of the rock properties greatly reduce the range of possible seismic solutions and this range contains the actual values given by the well. By means of a statistical inversion, we analyse how approximate a priori knowledge of the petrophysical properties and of their relationships with the seismic parameters can be of help in reducing the ambiguity of the inversion solutions and eventually in estimating the petrophysical properties of the specific target reservoir. This statistical inversion allows the determination of the most likely values of the sought rock properties along with their uncertainty ranges. The results show that the porosity is the best-resolved rock property, with its most likely value closely approaching the actual value found by the well, even when we insert somewhat erroneous a priori information. The hydrocarbon saturation is the second best-resolved parameter, but its most likely value does not match the well data. The depth of the target interface is the least-resolved parameter and its most likely value is strongly dependent on a priori information. Although no general conclusions can be drawn from the results of this exercise, we envisage that the proposed AVA–petrophysical inversion and its possible extensions may be of use in reservoir characterization.     

Role of epikarst in near‐surface hydrological processes in a soil mantled subtropical dolomite karst slope: implications of field rainfall simulation experiments

Epikarst exerts a strong control on run‐off generation in karst regions, but it is still unclear in karst regions. Our study aimed to demonstrate the effect of epikarst on near‐surface hydrological processes in a subtropical cockpit karst region of southwest China, using plot‐scale rainfall simulation experiments with different rainfall intensities (low and high) and antecedent moisture conditions (dry and wet). A trench excavated to the epikarst lower boundary allowed identification of flow pathways in the entire soil–epikarst architecture system, thus facilitating the water balance calculations using a conceptual model with the assumption of a two‐stage hydrological evolution. More than 70% of the total rainfall water moved vertically through the shallow soil layer and then was redistributed by the epikarst as subsurface flow occurring on the soil–epikarst interface, depression filling on epikarst surface, water held by epikarst and deep percolation. Epikarst water regulation capacity, defined as the sum of depression filling on epikarst surface, water held by epikarst, epikarst seepage flow and deep percolation, was 58 mm (wet antecedent condition) and 223 mm (dry antecedent condition). Total run‐off from the soil–epikarst system was dominated by saturated subsurface flow showing a threshold process controlled by epikarst storage capacity (storing as much as 181 mm of rainfall water under dry antecedent condition). Our study proved that despite the epikarst being relatively poorly developed and covered by a soil mantle, it still exerted a strong influence on near‐surface hydrological processes and thus should be adequately considered in future modelling of water recharge and depletion dynamics in this integrated soil–epikarst system. Copyright © 2015 John Wiley & Sons, Ltd.     

砂泥岩储层孔隙度和含水饱和度同步反演

基于岩石物理和地震反演理论,提出了一种同步反演储层孔隙度和含水饱和度的方法.以岩石物理为基础,建立了砂泥岩储层物性和弹性参数之间定量的关系-Simon模型,以贝叶斯理论为手段,结合不同类型的砂泥岩储层,建立了多信息联合约束的物性参数反演目标函数,并通过蒙特卡罗和遗传算法相结合的思路求解该目标函数,最终得到孔隙度和含水饱和度的同步反演结果.将该方法应用于河道砂和砂砾岩两种不同的砂泥岩储层中,孔隙度和含水饱和度数据的联合应用,进一步减少了储层预测的多解性,为石油地质综合研究提供了更加丰富准确的基础数据.     

Seismic time–frequency analysis as a robust method to estimate the fluid saturation: A case study of carbonates reservoir,Iran

The propagation of seismic waves through a saturated reservoir compresses the fluid in the pore spaces. During this transition, parts of seismic energy would be attenuated because of intrinsic absorption. Rock physics models make the bridge between the seismic properties and petrophysical reality in the earth. Attenuation is one of the significant seismic attributes used to describe the fluid behaviour in the reservoirs. We examined the core samples using ultrasonic experiments at the reservoir conditions. Given the rock properties of the carbonate reservoir and experiment results, the patchy saturation mechanism was solved for substituted fluid using the theory of modulus frequency. The extracted relationship between the seismic attenuation and water saturation was used in time–frequency analysis. We performed the peak frequency method to estimate the Q factor in the Gabor domain and determined the water saturation based on the computed rock physics model. The results showed how the probable fault in the reservoir has stopped the fluid movement in the reservoir and caused touching the water‐bearing zone through drilling.     

储层弹性与物性参数地震叠前同步反演的确定性优化方法

储层弹性与物性参数可直接应用于储层岩性预测和流体识别,是储层综合评价和油气藏精细描述的基本要素之一.现有的储层弹性与物性参数地震同步反演方法大都基于Gassmann方程,使用地震叠前数据,通过随机优化方法反演储层弹性与物性参数;或基于Wyllie方程,使用地震叠后数据,通过确定性优化方法反演储层弹性与物性参数.本文提出一种基于Gassmann方程、通过确定性优化方法开展储层弹性和物性参数地震叠前反演的方法,该方法利用Gassmann方程建立储层物性参数与叠前地震观测数据之间的联系,在贝叶斯反演框架下以储层弹性与物性参数的联合后验概率为目标函数,通过将目标函数的梯度用泰勒公式展开得到储层弹性与物性参数联合的方程组,其中储层弹性参数对物性参数的梯度用差分形式表示,最后通过共轭梯度算法迭代求解得到储层弹性与物性参数的最优解.理论试算与实际资料反演结果证明了方法的可行性.     

Integrating basin modeling with seismic technology and rock physics

We explore the link between basin modelling and seismic inversion by applying different rock physics models. This study uses the E‐Dragon II data in the Gulf of Mexico. To investigate the impact of different rock physics models on the link between basin modelling and seismic inversion, we first model relationships between seismic velocities and both (1) porosity and (2) effective stress for well‐log data using published rock physics models. Then, we build 1D basin models to predict seismic velocities derived from basin modelling with different rock physics models, in a comparison with average sonic velocities measured in the wells. Finally, we examine how basin modelling outputs can be used to aid seismic inversion by providing constraints for the background low‐frequency model. For this, we run different scenarios of inverting near angle partial stack seismic data into elastic impedances to test the impact of the background model on the quality of the inversion results. The results of the study suggest that the link between basin modelling and seismic technology is a two‐way interaction in terms of potential applications, and the key to refine it is establishing a rock physics models that properly describes changes in seismic signatures reflecting changes in rock properties.     

CO2 saturation estimates at Sleipner (North Sea) from seismic tomography and rock physics inversion

CO₂ saturations are estimated at Sleipner using a two-step imaging workflow. The workflow combines seismic tomography (full-waveform inversion) and rock physics inversion and is applied to a two-dimensional seismic line located near the injection point at Sleipner. We use baseline data (1994 vintage, before CO₂ injection) and monitor data that was acquired after 12 years of CO₂ injection (2008 vintage). P-wave velocity models are generated using the Full waveform inversion technology and then, we invert selected rock physics parameters using an rock physics inversion methodology. Full waveform inversion provides high-resolution P-wave velocity models both for baseline and monitor data. The physical relations between rock physics properties and acoustic wave velocities in the Utsira unconsolidated sandstone (reservoir formation) are defined using a dynamic rock physics model based on well-known Biot–Gassmann theories. For data prior to injection, rock frame properties (porosity, bulk and shear dry moduli) are estimated using rock physics inversion that allows deriving physically consistent properties with related uncertainty. We show that the uncertainty related to limited input data (only P-wave velocity) is not an issue because the mean values of parameters are correct. These rock frame properties are then used as a priori constraint in the monitor case. For monitor data, the Full waveform inversion results show nicely resolved thin layers of CO₂–brine saturated sandstones under intra-reservoir shale layers. The CO₂ saturation estimation is carried out by plugging an effective fluid phase in the rock physics model. Calculating the effective fluid bulk modulus of the brine–CO₂ mixture (using Brie equation in our study) is shown to be the key factor to link P-wave velocity to CO₂ saturation. The inversion tests are done with several values of Brie/patchiness exponent and show that the CO₂ saturation estimates are varying between 0.30 and 0.90 depending on the rock physics model and the location in the reservoir. The uncertainty in CO₂ saturation estimation is usually lower than 0.20. When the patchiness exponent is considered as unknown, the inversion is less constrained and we end up with values of exponent varying between 5 and 20 and up to 33 in specific reservoir areas. These estimations tend to show that the CO₂–brine mixing is between uniform and patchy mixing and variable throughout the reservoir.     

Gas saturation prediction and effect of low frequencies on acoustic impedance images at Foinaven Field

Low frequencies are necessary in seismic data for proper acoustic impedance imaging and for petrophysical interpretation. Without lower frequencies, images can be distorted leading to incorrect reservoir interpretation and petrophysical predictions. As part of the Foinaven Active Reservoir Management (FARM) project, a Towed Streamer survey and an Ocean Bottom Hydrophone (OBH) survey were shot in both 1995 and 1998. The OBH surveys contain lower frequencies than the streamer surveys, providing a unique opportunity to study the effects that low frequencies have on both the acoustic impedance image along with petrophysical time‐lapse predictions. Artefacts that could easily have been interpreted as high‐resolution features in the streamer data impedance volumes can be distinguished by comparison with the impedance volumes created from the OBH surveys containing lower frequencies. In order to obtain results from the impedance volumes, impedance must be related to saturation. The mixing of exsolved gas, oil and water phases involves using the Reuss (uniform) or Voigt (patchy approximation) mixing laws. The Voigt average is easily misused by assuming that the end‐points correspond to 0% and 100% gas saturation. This implies that the patches are either 0% gas saturation or 100% gas saturation, which is never the case. Here, the distribution of gas as it comes out of solution is assumed to be uniform until the gas saturation reaches a sufficiently high value (critical gas saturation) to allow gas to flow. Therefore, at low gas saturations the distribution is uniform, but at saturations above critical, it is patchy, with patches that range from critical gas saturation to the highest gas saturation possible (1 minus residual oil and irreducible water saturation).     

Post‐stack stratigraphic inversion workflow applied to carbon dioxide storage: application to the saline aquifer of Sleipner field‡

In the Norwegian North Sea, the Sleipner field produces gas with a high CO₂ content. For environmental reasons, since 1996, more than 11 Mt of this carbon dioxide (CO₂) have been injected in the Utsira Sand saline aquifer located above the hydrocarbon reservoir. A series of seven 3D seismic surveys were recorded to monitor the CO₂ plume evolution. With this case study, time‐lapse seismics have been shown to be successful in mapping the spread of CO₂ over the past decade and to ensure the integrity of the overburden. Stratigraphic inversion of seismic data is currently used in the petroleum industry for quantitative reservoir characterization and enhanced oil recovery. Now it may also be used to evaluate the expansion of a CO₂ plume in an underground reservoir. The aim of this study is to estimate the P‐wave impedances via a Bayesian model‐based stratigraphic inversion. We have focused our study on the 1994 vintage before CO₂ injection and the 2006 vintage carried out after a CO₂ injection of 8.4 Mt. In spite of some difficulties due to the lack of time‐lapse well log data on the interest area, the full application of our inversion workflow allowed us to obtain, for the first time to our knowledge, 3D impedance cubes including the Utsira Sand. These results can be used to better characterize the spreading of CO₂ in a reservoir. With the post‐stack inversion workflow applied to CO₂ storage, we point out the importance of the a priori model and the issue to obtain coherent results between sequential inversions of different seismic vintages. The stacking velocity workflow that yields the migration model and the a priori model, specific to each vintage, can induce a slight inconsistency in the results.     

油藏水驱开采时移地震监测岩石物理基础测量

岩石物理测量是油藏水驱开采时移地震监测的基础.在实验室对来自胜利油田的5块岩石样品模拟储层条件进行了水驱和气驱动态岩石物理弹性测量,重点分析了流体替换、温度、孔隙压力对岩石纵、横波速度的影响.实验表明,在水驱情形下,由于流体替换和温度、孔隙压力变化所引起的岩石纵横波速度的变化均很小,实施时移地震监测具有较大的风险性.相比之下,气驱可能引起较为明显的纵波速度变化,有利于时移地震监测的实施.进一步完善实验方法、丰富实验内容、是今后时移地震岩石物理实验研究的主要任务.