Distribution of suspended sediment concentration in wide sediment‐laden streams: A novel power‐law theory

The diffusion equation of suspended sediment concentration in a wide sediment‐laden stream flow is dependent on the vertical gradient of streamwise velocity and the sediment diffusivity. This study aims at investigating the influence of the streamwise velocity laws on the suspended sediment concentration distributions, resulting from the solution of the diffusion equation. Firstly, the sediment concentration distributions are obtained numerically from the solution of the diffusion equation using different velocity laws and compared with the experimental data. It is found that the power‐law approximation produces good computational results for the concentration distributions. The accuracy of using a power‐law velocity model is comparable with the results obtained from other classical velocity laws, namely log‐law, log wake‐law and stratified log‐law. Secondly, a novel analytical solution is proposed for the determination of sediment concentration distribution, where a power‐law, wall‐concentration profile is coupled with a concentration wake function. The power‐law model (for velocity and concentration) is calibrated using the experimental data, and then a generalized wake function is obtained by choosing a suitable law. The developed power‐law model involving the wake function adjusted by an exponent predicts the sediment concentration distributions quite satisfactorily. Finally, a new explicit formula for the suspended‐load transport rate is derived from the proposed theory, where numerical computation of integrals, as needed in the Einstein theory, is avoided.     

Precambrian snapshots: Morphodynamics of Torridonian fluvial braid bars revealed by three‐dimensional photogrammetry and outcrop sedimentology

Pre‐vegetation fluvial channels have long been considered predominantly sheet‐like in geometry, owing to hydraulic sections that rapidly widened rather than incise during floods. This motif has been paralleled to that of modern dryland rivers subject to sharp discharge fluctuations during ephemeral floods. However, a number of Precambrian fluvial successions have been recently appraised as the product of deep‐channelled systems characterized by relatively stable – probably perennial – discharge regimes. One such example is the ca 1·0 Ga Applecross Formation, part of the well‐studied Torridon Group of Scotland. To contribute to this debate and to provide refined morphodynamic models for the Applecross Formation, this article presents an integration of three‐dimensional photogrammetry and outcrop sedimentology applied to key exposures at Stoer Peninsula, north‐western Scottish Highlands. Analysis of selected sandbodies reveals that high‐relief fluvial sand bars, both mid‐channel and bank‐attached, evolved within deep, braided‐channel belts. These bars grew through complex mechanisms of accretion and reactivation related to different flood stages: upstream and downstream accretion probably occurred during waning‐flood stages characterized by high hydrograph levels and abundant sediment availability; lateral accretion took place during later waning‐flood stages, and it was associated in some cases with helical recirculation and increase in bend sinuosity. Overall, the depicted morphodynamics are consistent with prolonged flood events that cannot be reconciled with sharply fluctuating discharge regimes. Critical comparisons between the internal geometry of the studied bars and modern counterparts corroborate the findings herein. Thus, this study recommends stricter comparisons between the products of modern braided channels and Precambrian fluvial rock records featuring thick and well‐developed bar forms.     

Gilbert‐type deltas recording short‐term base‐level changes: Delta‐brink morphodynamics and related foreset facies

Gilbert‐type deltas are sensitive recorders of short‐term base‐level changes, but the delta‐front record of a base‐level rise tends to be erased by fluvial erosion during a subsequent base‐level fall, which renders the bulk record of base‐level changes difficult to decipher from the delta‐front deposits. The present detailed study of three large Pleistocene Gilbert‐type deltas uplifted on the southern coast of the Gulf of Corinth, Greece, indicates a genetic link between the delta‐front morphodynamic responses to base‐level changes and the delta‐slope sedimentation processes. Sigmoidal delta‐brink architecture signifies a base‐level rise and is accompanied by a debrite‐dominated assemblage of delta foreset deposits, thought to form when the aggrading delta front stores sediment and undergoes discrete gravitational collapses. Oblique delta‐brink architecture tends to be accompanied by a turbidite‐dominated assemblage of foreset deposits, which are thought to form when the delta‐front accommodation decreases and the sediment carried by hyperpycnal effluent bypasses the front. This primary signal of the system response to base‐level changes combines further with the secondary ‘noise’ of delta autogenic variation and possible allogenic fluctuations in fluvial discharge due to regional climatic conditions. Nevertheless, the evidence suggests that the facies trends of delta foreset deposits may be used to decipher the delta ‘hidden’ record of base‐level changes obliterated by fluvial topset erosion. Early‐stage bayhead deltas may be an exception from the hypothetical model, because their narrow front tends to be swept by river floods irrespective of base‐level behaviour and their subaqueous slope deposits are thus mainly turbidites.     

Grain‐size distributions and coastal morphodynamics along the southern Maryland and Virginia barrier islands

This study examined grain‐size distributions to address questions regarding geological and oceanographic controls on island morphodynamics along one of the longest undeveloped, mixed‐energy barrier island systems in the world. In particular, statistical analyses (i.e. analysis of variance, Tukey honest significant difference multiple comparison tests, nonparametric statistics and linear regression analysis) of 230 barrier island samples from Ocean City Inlet, Maryland, to the mouth of the Chesapeake Bay and 134 nearshore samples (d ≤ 10 m) identified grain‐size trends related to the morphodynamic characteristics of these systems. In general, the Virginia barrier islands north of Wachapreague Inlet and Assateague Island form a statistically different subset of grain sizes (medium‐grained to coarse‐grained sand) from the islands south of Wachapreague Inlet (fine‐grained sand). These textural trends corroborate the Pleistocene headlands of the Delmarva coastal compartment as the sediment source and indicate that some of the coarse‐grained to medium‐grained sediment bypasses the large sinks in the net southward longshore sediment transport system (i.e. Fishing Point and Chincoteague Inlet). This research also demonstrates that the preferential accumulation of coarse‐grained to medium‐grained sand on the ebb‐tidal delta at Wachapreague Inlet probably controls the erosional morphodynamics of the islands located downdrift (south) of the inlet. These results suggest that an increase in tidal prism, set up by sea‐level rise and/or a shift in wave climate/refraction patterns, may lead to barrier island fragmentation and a runaway transgression of this predominantly natural barrier island system. Consequently, a grain analysis of major coastal compartments, across multiple driving forces, can be used to assess coastal morphodynamics and the potential impact of climate change on coastal systems.     

Linking submarine channel–levee facies and architecture to flow structure of turbidity currents: insights from flume tank experiments

Submarine leveed channels are sculpted by turbidity currents that are commonly highly stratified. Both the concentration and the grain size decrease upward in the flow, and this is a fundamental factor that affects the location and grain size of deposits around a channel. This study presents laboratory experiments that link the morphological evolution of a progressively developing leveed channel to the suspended sediment structure of the turbidity currents. Previously, it was difficult to link turbidity current structure to channel–levee development because observations from natural systems were limited to the depositional products while experiments did not show realistic morphodynamics due to scaling issues related to the sediment transport. This study uses a novel experimental approach to overcome scaling issues, which results in channel inception and evolution on an initially featureless slope. Depth of the channel increased continuously as a result of levee aggradation combined with varying rates of channel floor aggradation and degradation. The resulting levees are fining upward and the grain‐size trend in the levee matches the upward decrease in grain size in the flow. It is shown that such deposit trends can result from internal channel dynamics and do not have to reflect upstream forcing. The suspended sediment structure can also be linked to the lateral transition from sediment bypass in the channel thalweg to sediment deposition on the levees. The transition occurs because the sediment concentration is below the flow capacity in the channel thalweg, while higher up on the channel walls the concentration exceeds capacity resulting in deposition of the inner levee. Thus, a framework is provided to predict the growth pattern and facies of a levee from the suspended sediment structure in a turbidity current.     

Three‐dimensional gravity‐current flow within a subaqueous bend: Spatial evolution and force balance variations

The nature of three‐dimensional flow in submarine channel bends is poorly understood, largely due to the absence of detailed data from natural channels. Herein, data from density‐driven flows in a large reservoir on the Huanghe (Yellow) River are presented showing the spatio‐temporal variation of flow around a subaqueous bend. The data demonstrate for the first time that reversed helical flow, relative to that found in river channel bends, can occur from the centrifugal forcing of flow, even when the Coriolis force acts in the opposite direction. The data also suggest that reversed helical flow fields in submarine channels may be more frequent than currently estimated, notably for bends where Coriolis and centrifugal forces combine in the same direction. In addition, this study provides the first field evidence suggesting that sinuous submarine channels can exhibit an asymmetry in helical flow orientation between left and right‐turning bends, which will have major implications for the morphodynamics of submarine channels, their resultant patterns of sedimentation and, ultimately, the distribution of depositional units across submarine fan systems.     

Anatomy of a submarine pyroclastic flow and associated turbidity current: July 2003 dome collapse, Soufrière Hills volcano, Montserrat, West Indies

The 12 to 13 July 2003 andesite lava dome collapse at the Soufrière Hills volcano, Montserrat, provides the first opportunity to document comprehensively both the sub‐aerial and submarine sequence of events for an eruption. Numerous pyroclastic flows entered the ocean during the collapse, depositing approximately 90% of the total material into the submarine environment. During peak collapse conditions, as the main flow penetrated the air–ocean interface, phreatic explosions were observed and a surge cloud decoupled from the main flow body to travel 2 to 3 km over the ocean surface before settling. The bulk of the flow was submerged and rapidly mixed with sea water forming a water‐saturated mass flow. Efficient sorting and physical differentiation occurred within the flow before initial deposition at 500 m water depth. The coarsest components (～60% of the total volume) were deposited proximally from a dense granular flow, while the finer components (～40%) were efficiently elutriated into the overlying part of the flow, which evolved into a far‐reaching turbidity current.     

Morphodynamics and depositional signature of low‐aggradation cyclic steps: New insights from a depth‐resolved numerical model

Bedforms related to Froude‐supercritical flow, such as cyclic steps, are increasingly frequently observed in contemporary fluvial and marine sedimentary systems. However, the number of observations of sedimentary structures formed by supercritical‐flow bedforms remains limited. The low number of observations might be caused by poor constraints on criteria to recognize these associated deposits. This study provides a detailed quantification on the mechanics of a fluvial cyclic step system, and their depositional signature. A computational fluid‐dynamics model is employed to acquire a depth‐resolved image of a cyclic step system. New insights into the mechanics of cyclic steps shows that: (i) the hydraulic jump is, in itself, erosional; (ii) there are periods over which the flow is supercritical throughout and there is no hydraulic jump, which plays a significant role in the morphodynamic behaviour of cyclic steps; and (iii) that the depositional signature of cyclic steps varies with rate of aggradation. Previous work has shown that strongly aggradational cyclic steps, where most of the deposited sediment is not reworked, create packages of backsets, bound upstream and downstream by erosive surfaces. Here, the modelling work is focussed on less aggradational conditions and more transportational systems. The depositional signature in such systems is dominated by an amalgamation of concave‐up erosional surfaces and low‐angle foresets and backsets creating lenticular bodies. The difference between highly aggradational cyclic steps and low‐aggradation steps can be visible in outcrop both by the amount of erosional surfaces, as well as the ratio of foreset to backset, with backsets being indicative of more aggradation.     

Multi‐scale analysis of a migrating submarine channel system in a tectonically‐confined basin: The Miocene Gorgoglione Flysch Formation,southern Italy

The Miocene Gorgoglione Flysch Formation records the stratigraphic product of protracted sediment transfer and deposition through a long‐lived submarine channel system developed in a narrow and elongate thrust‐top basin of the Southern Apennines (Italy). Channel‐fill deposits are exposed in an outcrop belt approximately 500 m thick and 15 km long, oriented oblique to the palaeoflow, which was roughly south‐eastward. These exceptional exposures of channel‐fill strata allow the stacking architectures and the evolution of the channel system to be analyzed at multiple scales, enabling the effects of syn‐sedimentary thrust tectonics and basin confinement on the depositional system development to be deciphered. Two end‐member types of elementary channel architecture have been identified: high‐aspect‐ratio, weakly‐confined channels, and low‐aspect‐ratio, incisional channels. Their systematic stacking results in a complex pattern of seismic‐scale depositional architectures that determines the stratigraphic framework of the deep‐water system. From the base of the succession, two prominent channel complex sets have been recognized, namely CS1 and CS2, consisting of amalgamated incisional channel elements and weakly‐confined channel elements. These channelized units are overlain by isolated incisional channels, erosional into mud‐prone slope deposits. The juxtaposition of different channel architectures is interpreted to have been governed by regional thrust‐tectonics, in combination with a high subsidence rate that promoted significant aggradation. In this scenario, the alternating ‘in sequence’ and ‘out of sequence’ tectonic pulses of the basin‐bounding thrusts controlled the activation of coarse‐clastic inputs in the basin and the resulting stacking architectures of channelized units. The tectonically‐driven confinement of the depositional system limited the lateral offset in channel stacking, preventing large‐scale avulsions. This study represents an excellent opportunity to analyze the stratigraphic evolution of a submarine channel system in tectonically‐active settings from an outcrop perspective. It should find wide applicability in analogous depositional systems, whose stratigraphic architecture has been influenced by tectonically‐controlled lateral confinement and associated lateral tilting.     

Origin,evolution and anatomy of silt‐prone submarine external levées

Submarine external levées are constructional features that develop outside slope channel systems, and are a volumetrically significant component of continental margins. However, detailed observations of their process sedimentology and depositional architecture are rare. Extensive exposures of external levées at multiple stratigraphic intervals and well‐constrained palaeogeographic positions in the Fort Brown Formation, Karoo Basin, South Africa, have been calibrated with research boreholes. This integrated data set permits their origin, evolution and anatomy to be considered, including high‐resolution analysis of sedimentary facies distribution and characterization of depositional sub‐environments. An idealized model of the stratigraphic evolution and depositional architecture of external levées is presented, and variations can be attributed to allogenic (for example, sediment supply) and autogenic (for example, channel migration) factors. Initiation of external levée construction is commonly marked by deposition of a basal sand‐rich facies with sedimentary structures indicating rapid deposition from unconfined flows. These deposits are interpreted as frontal lobes. Propagation of the parent channel, and resultant flow confinement, lead to partial erosion of the frontal lobe and development of constructional relief (levées) by flow overspill and flow stripping. Overall fining‐upwards and thinning‐upwards profiles reflect increased flow confinement and/or waning flow magnitude through time. Identification of a hierarchy of levée elements is not possible due to the absence of internal bounding surfaces or sharp facies changes. The down‐slope taper in levée height and increasing channel sinuosity results in increasing numbers of crevasse lobe deposits, and is reflected by the increased occurrences of channel avulsion events down‐dip. External levées from the Fort Brown Formation are silt‐rich; however their stratigraphic evolution and the distribution of many components (such as sediment waves and crevasse lobe) share commonalities with mud‐rich external levées. This unique integrated data set has permitted the first high‐resolution characterization of external submarine levée systems.     

An experimental investigation of sand–mud suspension settling behaviour: implications for bimodal mud contents of submarine flow deposits

The settling behaviour of particulate suspensions and their deposits has been documented using a series of settling tube experiments. Suspensions comprised saline solution and noncohesive glass‐ballotini sand of particle size 35·5 μm < d < 250 μm and volume fractions, φ_s, up to 0·6 and cohesive kaolinite clay of particle size d < 35·5 μm and volume fractions, φ_m, up to 0·15. Five texturally distinct deposits were found, associated with different settling regimes: (I) clean, graded sand beds produced by incremental deposition under unhindered or hindered settling conditions; (II) partially graded, clean sand beds with an ungraded base and a graded top, produced by incremental deposition under hindered settling conditions; (III) graded muddy sands produced by compaction with significant particle sorting by elutriation; (IV) ungraded clean sand produced by compaction and (V) ungraded muddy sand produced by compaction. A transition from particle size segregation (regime I) to suppressed size segregation (regime II or III) to virtually no size segregation (IV or V) occurred as sediment concentration was increased. In noncohesive particulate suspensions, segregation was initially suppressed at φ_s ～ 0·2 and entirely inhibited at φ_s ≥ 0·6. In noncohesive and cohesive mixtures with low sand concentrations (φ_s < 0·2), particle segregation was initially suppressed at φ_m ～ 0·07 and entirely suppressed at φ_m ≥ 0·13. The experimental results have a number of implications for the depositional dynamics of submarine sediment gravity flows and other particulate flows that carry sand and mud; because the influence of moving flow is ignored in these experiments, the results will only be applicable to flows in which settling processes, in the depositional boundary, dominate over shear‐flow processes, as might be the case for rapidly decelerating currents with high suspended load fallout rates. The ‘abrupt’ change in settling regimes between regime I and V, over a relatively small change in mud concentration (<5% by volume), favours the development of either mud‐poor, graded sandy deposits or mud‐rich, ungraded sandy deposits. This may explain the bimodality in sediment texture (clean ‘turbidite’ or muddy ‘debrite’ sand or sandstone) found in some turbidite systems. Furthermore, it supports the notion that distal ‘linked’ debrites could form because of a relatively small increase in the mud concentration of turbidity currents, perhaps associated with erosion of a muddy sea floor. Ungraded, clean sand deposits were formed by noncohesive suspensions with concentrations 0·2 ≤ φ_s ≤ 0·4. Hydrodynamic sorting is interpreted as being suppressed in this case by relatively high bed aggradation rates which could also occur in association with sustained, stratified turbidity currents or noncohesive debris flows with relatively high near‐bed sediment concentrations.     

Architecture and morphodynamics of a 1·6 Ga fluvial sandstone: Ellice Formation of Elu Basin,Arctic Canada

Precambrian fluvial deposits have been traditionally described as architecturally simple, forming shallow and wide braidplains with sheet‐like geometry. The varied architecture and morphodynamics of the 1·6 Ga Ellice Formation of Elu Basin, Nunavut, Canada, are examined from detailed studies of section and planform exposures along coastal platforms and stepped cliffs. The Ellice Formation overlies older Proterozoic sandstones and Archean crystalline rocks, recording sedimentation in fluvial, aeolian, coastal and nearshore‐marine environments. The fluvial deposits display palaeoflow towards the west/north‐west, while overlying shallow‐marine deposits record transgression towards the east/south‐east. The Ellice Formation displays dispersed palaeoflow at its base, and also at higher stratigraphic levels, where fluvial and aeolian deposits are associated. Elsewhere, mainly unimodal palaeoflow points to extensive low‐sinuosity fluvial deposition. Within the terrestrial deposits, fluvial, fluvial–aeolian and coastal architectural elements are recognized. Fluvial elements comprise cross‐bedded sandstone and minor conglomerate, exhibiting an overall fining‐upward trend with associated decrease in preservation, dimension and amalgamation of channel bodies. These motifs are interpreted to portray a shift in depositional environment from proximal trunk rivers to distal alluvial plains. Low‐sinuosity fluvial elements are the most common, and include major channel bodies, elongate side bars and mid‐channel bars with well‐developed scroll topography. High‐sinuosity channel‐bar complexes exhibit upbar‐flow rotation and yield evidence of bar expansion coupled with rotation and translation. Fluvial–aeolian elements are composed of aeolian dunes juxtaposed with isolated channel bodies and bank‐attached bars. Minor mixed fluvial–aeolian sheets record local deposition in unconfined settings (possibly floodbasins) or inter‐distributary highlands. Finally, coastal elements comprise small deltaic complexes composed of sand‐rich distributary‐channel bodies feeding heterolithic mouth bars. Overall, the sedimentary record of the Ellice Formation demonstrates an example from the Precambrian where alluvium was locally characterized by a higher geomorphic variability than previously recognized.     

Autogenic incision‐backfilling cycles and lobe formation during the growth of alluvial fans with supercritical distributaries

Autogenic cycles of channelization, terminal deposit formation, channel backfilling and channel abandonment have been observed in the formation of fans and deltas. In subcritical flow, these terminal deposits are characterized as mouth bars that lead to flow bifurcation, backwater and eventual channel backfilling. Similar, although less well characterized, cycles also take place on supercritical subaerial and submarine fans. This study investigates the hydraulics and morphodynamics of autogenic incision and backfilling cycles associated with supercritical distributive channel flow in alluvial fans. The research questions of the study are: (i) how are supercritical autogenic cycles on alluvial fans different from the subcritical cycles; (ii) what are the hydraulic and sediment transport characteristics at the various stages of autogenic feedback cycles; and (iii) what role do the cycles play in the overall fan evolution? These questions are investigated in the laboratory, and emphasis is placed on measuring the hydraulic and topographic evolution of the systems during the cycles. The cycles arise quasi‐periodically under constant water and sediment discharge. Periods of sheet‐like flow are competent to move sediment () but not competent enough to carry the full imposed load. The net result is preferential deposition near the inlet, resulting in fan steepening and an increase in flow competency with time. At a sediment supply to capacity ratio of , the sheet‐like flow is unstable to small erosional events near the inlet, resulting in the collapse of the distributed flow to a strong channelized state. During channelization, a graded () supercritical (Fr > 1) channel develops and transports eroded and fed sediment up to and through the fan front – extending the fan, initiating a lobe shaped deposit and reducing the local slope. The slopes defined by a sheet‐like flow with and channelized flow with set the maximum and minimum slopes on the fan, respectively. Once formed, graded channels act as bypass conduits linking the inlet with the terminal deposit. On average, deposits are up to six channel depths in thickness and have volumes approximately five times that of the excavated channel. The main distinctive characteristics of the supercritical cycles relate to how the flow interacts with the terminal deposit. At the channel to deposit transition, the flow undergoes a weak hydraulic jump, resulting in rapid sedimentation, dechannelization and lateral expansion of the flow, and deposition of any remaining sediment on top of the channel fill and floodplain. This process often caps the channel as the deposit propagates up channel erasing memory of the excavated channel.     

Three-dimensional bounding surface architecture and lateral facies heterogeneity of a wet aeolian system: Entrada Sandstone,Utah

Aeolian deposits form noteworthy reservoirs (for example, Norphlet Formation and Rotliegend Group) in hydrocarbon extraction and carbon capture and storage contexts, but stratigraphic architecture imparts significant heterogeneity. Bounding surfaces result from autogenic and allogenic controls and can represent important changes in dune-field dynamics. To further evaluate the impacts of facies heterogeneity and flow-inhibiting bounding surfaces on reservoir performance and reconstruct ancient erg evolution, the stratigraphic architecture of aeolian systems must continue to be studied at multiple scales. This study pairs traditional methods (for example, measured stratigraphic sections) with advanced technologies (for example, drone-derived outcrop models) to precisely resolve the metre to kilometre-scale three-dimensional stratigraphic architecture of wet aeolian Middle Jurassic Entrada Sandstone outcrops located at Rone Bailey Mesa near Moab, Utah, USA. Five facies are identified, primarily based on sedimentary fabrics, and are grouped into three associations named dune, sabkha and sand sheet. Statistical analyses of gamma-ray spectrometer and automated mineralogy data indicate a distinct mineralogical difference between dune (quartz-rich) and sabkha (more feldspathic) packages, suggesting that gamma-ray logs may be used to better predict facies distribution in the subsurface. Seven modelled super bounding surfaces are planar to undulatory, with no perceived spatial trends. Five modelled interdune migration surfaces are undulatory but exhibit an average 0.09° angle of climb roughly parallel to the palaeocurrent direction. Two modelled superposition surfaces are linear to sinuous in plan-view. Laterally discontinuous sabkha packages observed are interpreted to be remnants of closed, damp, interdune flats located between ca 8.5 to 17.0 m tall, sinuous, transverse bedforms or patches of such bedforms. Based on stratigraphic architecture interpretations, the Entrada Sandstone preserves signals of allogenic forcing and localized autogenic bedform cannibalization of the substrate. The findings of this study, some of which are not commonly recognized in wet aeolian facies models, enhance the understanding of erg evolution and can parameterize static models of aeolian reservoirs.     

Cavity‐filling dolomite speleothems and submarine cements in the Ediacaran Dengying microbialites,South China: Responses to high‐frequency sea‐level fluctuations in an ‘aragonite–dolomite sea’

Speleothems, mostly composed of calcium carbonate, are widely present in modern karst‐originated caves, but have rarely been reported in palaeokarst systems. This study presents a novel type of dolomite speleothem and subsequent submarine dolomite cement, which are widely present in the upper Ediacaran Dengying Formation in the upper Yangtze area. These precipitated materials occur in the cavity system that cuts across several peritidal cycles. The interconnected cavity networks with irregular shapes, embayed walls, internal breccias on cavity floor and their preferential development in the shallower cycle tops (for example, tepee‐deformed beds) suggest that they were initially generated by subaerial dissolution. As the earliest infills, the hemispherical protrusions, icicle‐like pendants and ground‐up columns show similar morphological features and occurrence patterns to the cave popcorn, stalactites and stalagmites, respectively. Thus, these earliest infills are speleothems resulting from associated meteoric precipitation during subaerial exposure. The isopachous growth pattern of subsequent more extensive fibrous dolomite cements points to a submarine diagenetic environment in which they were precipitated. Microscopically, the micritic to micro‐crystalline dolomite, acicular dolomite in speleothems and the subsequent fibrous dolomite share similar crystal fabrics to metastable precursors (for example, Mg‐calcite). Meanwhile, the carbon‐oxygen isotope compositions of the speleothem and fibrous dolomite, although partly altered by burial diagenesis, share a large overlap with host rock and coeval marine carbonates all over the Yangtze Platform. For these reasons, these speleothems and fibrous cements are considered to have been initially precipitated as metastable carbonate precursors in meteoric and submarine environments, respectively, and stabilized during submarine mimetic dolomitization. The cyclic occurrence of cavity systems filled with speleothems and submarine cements reflects periodic subaerial exposure and marine flooding of broad tidal flat in the upper Yangtze area, driven by high‐frequency sea‐level fluctuations. Furthermore, the Neoproterozoic seawater chemistry that favoured early dolomitization of carbonate precursor mineralogies was an advantage for the preservation of fabrics from metastable precursor minerals.     

Morpho‐sedimentary characteristics of proximal gravel braided river deposits in a Froude‐scaled physical model

A Froude‐scaled physical model of a proximal gravel‐bed braided river was used to connect the river morphological characteristics, and sedimentary processes and forms, to deposit geometry. High resolution continuous three‐dimensional topographic data were acquired from sequential photogrammetric digital elevation models paired with grain‐size surface maps derived from image analysis of textural properties of the surface. From these data, the full three‐dimensional development of the braided river deposit and grain‐size sorting patterns was compiled over an experimental time period of 41 h during which the model river reworked a large portion of the braided channel. The minimum surface of the deposit is developed progressively over time by erosion, migration and avulsion of channels, and by local scour at channel confluences. The maximum surface of the deposit is formed by amalgamation of braid bar surfaces and has less overall relief than the minimum surface. Confluence scour constitutes about 5% of the area of the minimum surface. Migration of individual confluences is limited to distances of the order of the width and length of the confluence, so that confluences do not form laterally extensive deposits and basal surfaces. Maximum and minimum surfaces have very similar grain‐size distributions, and there is no extensive basal coarse layer. Deposit maximum thickness is strongly associated with large channel confluences which occur as deeper areas along the main channel belt and make up a large proportion of the thickest portions of the deposit.     

Deposit architecture and dynamics of the 2006 block‐and‐ash flows of Merapi Volcano,Java, Indonesia

The internal architecture of the 2006 block‐and‐ash flow deposits of Merapi volcano (Java, Indonesia) was investigated using data collected from 27 stratigraphic sections measured immediately after flow emplacement, and after one and two rainy seasons of erosion. Identification of different depositional units and their longitudinal and lateral facies variations provide detailed information about: (i) the distribution, volumes and sedimentological characteristics of the different units; (ii) flow types and mobility as inferred from associated deposits; and (iii) changes in the dynamics of the different flows and their material during emplacement. Two main types of block‐and‐ash flows (short‐runout to medium‐runout block‐and‐ash flows and long‐runout block‐and‐ash flows) are defined based on flow generation mechanism, flow volume, travel distance, deposit morphology, distribution, lithology and grain‐size distribution. Conceptual models for the transport and depositional mechanisms of these two types of block‐and‐ash flows are presented. Variations in the runout distances observed for short‐runout to medium‐runout block‐and‐ash flows are linked directly to different initial flow volumes, degree of fragmentation and material properties of the moving mass during transport, with the largest and finer grained flows having the greatest mobility. Deposition occurs only over a narrow range of basal inclinations close to the angle of repose for pyroclastic material, indicating that such flows behave in a similar way to granular‐free surface flows on unconfined planes. The flow mechanisms of long‐runout block‐and‐ash flows at Merapi are interpreted to be similar, in many respects, to unsteady, cohesionless grain flows with an inertial flow regime where collisional forces largely overcome frictional forces. Flow unsteadiness causes the main body to be segmented into different pulses that run closer to each other as the flow moves downslope. Deposition occurs stepwise, with rapid aggradation of stacked sub‐units from different parts of the major flow pulses. In such a model, the arrival of each flow pulse front at selected sites in the main river valley controls the generation and development of highly mobile, unconfined pyroclastic flows outside valley regions and their associated overbank deposits.     

Supply‐limited bedform patterns and scaling downstream of a gravel–sand transition

A distinct suite of sand bedforms has been observed to occur in laboratory flows with limited sand supply. As sand supply to the bed progressively increases one observes sand ribbons, discrete barchans and, eventually, channel spanning dunes; but there are relatively few observations of this sequence from natural river channels. Furthermore, there are few observations of transitions from limited sand supply to abundant supply in the field. Bedforms developed under limited, but increasing, sand supply downstream of the abrupt gravel–sand transition in the Fraser River, British Columbia, are examined using multi‐beam swath‐bathymetry obtained at high flow. This is an ideal location to study supply‐limited bedforms because, due to a break in river slope, sand transitions from washload upstream of the gravel–sand transition to bed material load downstream. Immediately downstream, barchanoid and isolated dunes are observed. Most of the bedform field has gaps in the troughs, consistent with sand moving over a flat immobile or weakly mobile gravel bed. Linear, alongstream bedform fields (trains of transverse dunes formed on locally thick, linear deposits of sand) exhibit characteristics of sand ribbons with superimposed bedforms. Further downstream, channel spanning dunes develop where the bed is composed entirely of sand. Depth scaling of the dunes does not emerge in this data set. Only where the channel has accumulated abundant sand on the bed do the dunes exhibit scaling congruent with previous data compilations. The observations suggest that sediment supply plays an important, but often overlooked, role in bedform scaling in rivers.     

Relationships between high‐magnitude relative sea‐level changes and filling of a coarse‐grained submarine canyon (Pleistocene,Ionian Calabria,Southern Italy)

A middle Pleistocene coarse‐grained canyon fill succession (the Serra Mulara Formation) crops out in the northern sector of the Crotone Basin, a forearc basin located on the Ionian side of the Calabrian Arc and active from the Serravallian to middle Pleistocene. This succession is an example of coarse‐grained submarine canyon fill, which consists of a north‐west to south‐east elongated body (4·25 km long and up to 1·5 km wide) laterally confined by a deep‐water clayey and silty succession and located behind the modern Neto delta (north of Crotone). The thickness of the unit reaches 178 m. The lower part of the canyon fill is dominated by gravelly to sandy density‐flow deposits containing abundant bivalve and gastropod fragments, passing upward into a succession composed of metre‐scale to decimetre‐scale density‐flow deposits forming sandstone–mudstone couplets. Sandstone deposits are mostly structureless and planar‐laminated, whereas the clayey layers record hemipelagic deposition during quieter phases. This succession is overlain by another composed of thicker structureless sandstones alternating with layers of interlaminated mudstones and sandstones, which contain leaf remnants and fresh water ostracods, and are linked directly to river floods. The canyon fill is overlain by gravelly to sandy continental deposits recording a later stage of emergence. Facies analysis, together with micropalaeontological data from the hemipelagic units, suggests that the studied canyon fill records, firstly, a progressive gravel material cut‐off during deposition due to an overall relative sea‐level rise, leading to a progressive increase in the entrapment of sediment in fluvial to shallow‐marine systems, and secondly, a generalized relative sea‐level lowering. This trend probably reflects high‐magnitude glacio‐eustatic changes combined with the regional uplift of the region, ultimately leading to emergence.     

Mud dispersal across a Cretaceous prodelta: Storm‐generated,wave‐enhanced sediment gravity flows inferred from mudstone microtexture and microfacies

Determining sediment transport direction in ancient mudrocks is difficult. In order to determine both process and direction of mud transport, a portion of a well‐mapped Cretaceous delta system was studied. Oriented samples from outcrop represent prodelta environments from ca 10 to 120 km offshore. Oriented thin sections of mudstone, cut in three planes, allowed bed microstructure and palaeoflow directions to be determined. Clay mineral platelets are packaged in equant, face‐face aggregates 2 to 5 μm in diameter that have a random orientation; these aggregates may have formed through flocculation in fluid mud. Cohesive mud was eroded by storms to make intraclastic aggregates 5 to 20 μm in diameter. Mudstone beds are millimetre‐scale, and four microfacies are recognized: Well‐sorted siltstone forms millimetre‐scale combined‐flow ripples overlying scoured surfaces; deposition was from turbulent combined flow. Silt‐streaked claystone comprises parallel, sub‐millimetre laminae of siliceous silt and clay aggregates sorted by shear in the boundary layer beneath a wave‐supported gravity flow of fluid mud. Silty claystone comprises fine siliceous silt grains floating in a matrix of clay and was deposited by vertical settling as fluid mud gelled under minimal current shear. Homogeneous clay‐rich mudstone has little silt and may represent late‐stage settling of fluid mud, or settling from wave‐dissipated fluid mud. It is difficult or impossible to correlate millimetre‐scale beds between thin sections from the same sample, spaced only ca 20 mm apart, due to lateral facies change and localized scour and fill. Combined‐flow ripples in siltstone show strong preferred migration directly down the regional prodelta slope, estimated at ca 1 : 1000. Ripple migration was effected by drag exerted by an overlying layer of downslope‐flowing, wave‐supported fluid mud. In the upper part of the studied section, centimetre‐scale interbeds of very fine to fine‐grained sandstone show wave ripple crests trending shore normal, whereas combined‐flow ripples migrated obliquely alongshore and offshore. Storm winds blowing from the north‐east drove shore‐oblique geostrophic sand transport whereas simultaneously, wave‐supported flows of fluid mud travelled downslope under the influence of gravity. Effective wave base for sand, estimated at ca 40 m, intersected the prodelta surface ca 80 km offshore whereas wave base for mud was at ca 70 m and lay ca 120 km offshore. Small‐scale bioturbation of mud beds co‐occurs with interbedded sandstone but stratigraphically lower, sand‐free mudstone has few or no signs of benthic fauna. It is likely that a combination of soupground substrate, frequent storm emplacement of fluid mud, low nutrient availability and possibly reduced bottom‐water oxygen content collectively inhibited benthic fauna in the distal prodelta.