涡流发生器对潮流能水轮机翼型水动力学特性影响的数值模拟

为了改善潮流能水轮机叶片表面流动分离问题,提高其升阻比,本文通过在潮流能水轮机叶片表面加装涡流发生器,来研究涡流发生器对潮流能水轮机水动力学性能的影响。本文以NACA4418翼型为研究对象,分别建立了含VGs和不含VGs的三维模型,利用CFD方法研究了VGs的高度、长度以及相邻一对VGs之间的间距等多个方面对该翼型性能的影响。结果表明:VGs可以有效地提高翼型的最大升力系数;相邻VGs间距的增加对流动分离的抑制有积极影响。此外,通过对尾迹区流线和旋涡的分析,进一步揭示了尾迹区的流场特征。     

平板对下游方柱流体动力性能影响分析

基于有限体积法求解二维粘性不可压缩Navier-Stokes方程,分别采用层流模型和Realizable k-ε模型研究Re=250和Re=104前置平板与下游方柱间的流动干扰现象,分析不同尺度的平板布置在不同位置时对下游方柱的绕流场及流体动力性能的影响。计算发现在方柱上游布置平板可以有效的控制方柱的绕流场,减小方柱的阻力系数和升力系数;随着平板尺度的增加,方柱的阻力系数、升力系数呈下降趋势;并且存在较好的平板布置区间,可以最大程度的降低方柱和平板的阻力系数及方柱的升力系数,从而达到良好的减振、降噪的效果。     

Reynolds and Mass-Damping Effect on Prediction of the Peak Amplitude of A Freely Vibrating Cylinder

The Reynolds effect and mass-damping effect on the peak amplitude of a freely vibrating cylinder is studied by using forced oscillating data from Gopalkrishnan＇ s research in 1993, in which all experimental cases were carried out at a fixed Reynolds and the tested cylinder was recognized as a body that had no mass and damping. However, the Reynolds and roass-damping are the very important parameters for the peak amplitude of a freely vibrating cylinder. In the present study, a function F is introduced to connect the forced oscillation and free vibration. Firstly the peak amplitude AG^＊ can be obtained from the function F using forced oscillation data of Gopalkrishnan＇ s experimental at Re = 10^4, and then the Reynolds effect is taken into account in the function f（Re）, while the mass-damping effect is considered in the function K（ α ）, where a is the mass-damping ratio. So the peak amplitude of a freely vibrating cylinder can be predicted by the expression： A ^＊ = K（ α ）f（ Re ）AG^＊ . It is found that the peak transverse amplitudes predicted by the above equation agree very well with many recent experimental data under both high and low Reynolds conditions while roass-damping varies. Furthermore, it is seen that the Reynolds number does have a great effect on the peak amplitude of a freely vibrating cylinder. The present idea in this paper can be applied as an update in the empirical models that also use forced oscillation data to predict the vortex induced vibration （VIV） response of a long riser in the frequency domain.     

防振锤对深水导管架圆管风致涡激振动抑制研究

研究了阻尼防振锤对深水导管架圆管风致涡激振动的抑制。建立了防振锤动力学模型,分析了防振锤的动力学特性;将在建深水导管架圆管简化为固支梁,建立了结构有限元模型,通过瞬态分析计算了圆管的振动幅值;在圆管中部添加防振锤,分析了防振锤对圆管振动的抑制效果;进行了现场测试,对比了数值模拟和实际测试管道的振动响应。研究表明,文中设计的防振锤可以有效地抑制圆管的涡激共振;数值模拟结果与测试结果非常接近,验证了数值分析方法的有效性。     

导管架圆管风致涡激振动对总体疲劳性能的影响

研究了在建阶段导管架圆管发生风致涡激振动对整体疲劳性能的影响。建立了圆管动力学模型,分析了圆管的动力学特性;固定系数取值0.7模拟实际工程中圆管两端的焊接约束形式,计算了圆管的振动响应;基于线性累积损伤准则和S-N曲线计算了圆管发生风致涡激振动的疲劳损伤度,并根据规范计算出圆管在位阶段的疲劳损伤度,对比总结风致涡激振动对总体疲劳性能的影响以及振动抑制措施对疲劳性能的改善。研究表明,在建阶段导管架圆管发生风致涡激振动会明显地影响圆管的疲劳特性,降低疲劳寿命,因此可以通过绑定绳索、安装防振锤等手段减少结构的疲劳损伤。     

岬湾海岸中人工岛建设对岬角涡旋及海湾地形冲淤的影响——以海南岛铺前湾为例

岬湾海岸中一般在岬角的右侧与左侧（面向大海方向）分别发育顺时针与逆时针涡流。这些涡流的存在对泥沙输运、海底地形演变、污染物扩散等都具有重要影响。而在海洋中岛屿的存在将产生局部的岛后尾流。如岛屿与岬角距离较近,岛后尾流可能与岬角涡旋相互作用,反之则相互影响较小。本文以海南岛铺前湾为例,研究在岬湾海岸中湾口处的人工岛建设对湾内涡旋的影响,并进一步分析人工岛建设对整个海湾海底冲淤变化的效应。本项研究主要采用COAWST模型进行研究。结果表明,大潮期在海湾内发育大范围的顺时针涡旋,小潮期涡旋发育不明显,以东向余流为主。人工岛建设并未影响整个海湾的涡旋结构,但人工岛分隔了湾内顺时针涡旋,且在周围产生局部的逆时针与顺时针涡旋。海底冲淤变化的基本格局为湾内以淤积为主,人工岛建设加强了这种趋势,但在人工岛与岸线之间的狭窄通道内,海底出现冲刷。本项研究对岬湾海岸的科学开发管理具有一定意义。     

海洋风场动态可视化研究

针对海洋环境数据多维、多格式及动态性的特点,在深入研究OSG三维可视化仿真平台的基础上,采用颜色映射与点图标映射,结合几何着色器与osg Earth三维虚拟地球场景,提出一套海洋风场可视化的方法.实验结果表明,本方法很好的实现了海洋风场动态可视化,为海洋环境的动态可视化提供了一个强有力的研究平台.     

多模块超大型浮体中连接器刚度对其运动响应的影响

多模块超大型浮体一般由连接器连接,实现海上浮动机场等功能。实际操作中,为约束超大型浮体模块之间的相对运动,连接器通常将承受非常巨大的载荷,给连接器的制造带来巨大的困难。通过对不同环境力情况下不同刚度连接器的研究,分析了连接器刚度对超大型浮体模块之间相对运动与连接器自身承受载荷的影响。研究发现,随着柔性连接器刚度的增加,连接器对超大浮体模块之间相对运动的约束逐渐增强,同时连接器也将承受更大的载荷;此外,较大的连接器刚度,并不利于抵抗模块之间的冲击载荷;最后,连接器刚度的改变会影响其固有振动频率,因此需要尽可能避开共振区域,否则系统容易出现较大的振动,导致模块间相对运动过大,连接器过载。研究结果确定了连接器刚度最佳匹配原则,以指导连接器的工程设计。     

水深对软刚臂单点系泊FPSO动力响应的影响

系泊系统的定位能力是浅水油田作业的软刚臂式单点系泊FPSO安全作业的重要保障,为研究不同水深/吃水比下单点系泊系统的受力性能,针对一艘16万吨级软刚臂单点系泊FPSO,在线性三维势流理论的基础上,基于多体动力学方法,建立FPSO-系泊腿-软刚臂的耦合模型,采用Newman近似法和Pinkster近似法分析了FPSO所受二阶波浪力,在时域内计算了不同水深/吃水比对系泊系统动力响应性能的影响。结果表明,随着水深/吃水比的增加,Newman近似法计算得到二阶波浪力先增大后减小,引起单点系泊系统载荷先增大后减小;而Pinkster近似法计算得到的二阶波浪力逐渐减下,引起单点载荷逐渐减下。在浅水条件下,Pinkster近似法具有较好的适用性,Newman近似法严重低估了FPSO所受的二阶波浪力;在深水条件下,Newman近似法能满足工程计算的要求;适用两种方法的临界水深/吃水比为1.64。     

基于有限差分法的复合系泊链缆动力模型及其验证

具有链—缆—链结构的复合系泊链缆因其相对于全钢链质量和成本上的优势而在深水系泊中得以广泛应用。基于细长杆理论采用有限差分法建立了可以考虑链—缆—链结构的复合系泊缆数值模型,将其应用于不同工况下全钢链和复合链缆运动的数值模拟中,并开展了验证。首先,将单根钢链顶张力数值模拟结果与不同工况下的模型试验结果进行了对比,验证了数值预报程序应用于全钢链的准确性。然后,对于复合系泊链缆开展了静刚度和动刚度迭代数值模拟,并将模拟结果同已发表文章中的算例结果进行比较,验证了该数值模型在复合链缆模拟上的准确性。发现对于单根钢锚链的验证,激励半径越大,激励周期越小,一个周期内顶张力幅值及其极差越大,钢链运动就越剧烈。对于链—缆—链式复合系泊链缆的验证,发现静刚度迭代中数值模拟结果与算例结果差异较小;对于动刚度迭代,除个别大幅慢漂工况外,两者有较高的吻合;且激励周期越小,激励半径越大,复合系泊链缆顶张力越大,弹性模量越小,运动越剧烈。对于聚酯缆刚度的敏感性分析,发现改变动刚度经验公式参数的情况下,杨氏模量的静刚度迭代和动刚度迭代结果误差分别最大达到了60.81%和68.21%,因此合成纤维材料特性对复合系泊链...     

The construction of high precision geostrophic currents based on new gravity models of GOCE and satellite altimetry data

The new gravity field models of gravity field and steady-state ocean circulation explorer(GOCE), TIM_R6 and DIR_R6, were released by the European Space Agency(ESA) in June 2019. The sixth generation of gravity models have the highest possible signal and lowest error levels compared with other GOCE-only gravity models, and the accuracy is significantly improved. This is an opportunity to build high precision geostrophic currents. The mean dynamic topography and geostrophic currents have been calculated by the 5 th(TIM_R5 and DIR_R5), 6 th(TIM_R6 and DIR_R6) release of GOCE gravity field models and ITSG-Grace2018 of GRACE gravity field model in this study. By comparison with the drifter results, the optimal filtering lengths of them have been obtained(for DIR_R5, DIR_R6, TIM_R5 and TIM_R6 models are 1° and for ITSG-Grace2018 model is 1.1°). The filtered results show that the geostrophic currents obtained by the GOCE gravity field models can better reflect detailed characteristics of ocean currents. The total geostrophic speed based on the TIM_R6 model is similar to the result of the DIR_R6 model with standard deviation(STD) of 0.320 m/s and 0.321 m/s, respectively. The STD of the total velocities are 0.333 m/s and 0.325 m/s for DIR_R5 and TIM_R5. When compared with ITSG-Grace2018 results, the STD(0.344 m/s) of total geostrophic speeds is larger than GOCE results, and the accuracy of geostrophic currents obtained by ITSG-Grace2018 is lower. And the absolute errors are mainly distributed in the areas with faster speeds, such as the Antarctic circumpolar circulation, equatorial region, Kuroshio and Gulf Stream areas. After the remove-restore technique was applied to TIM_R6 MDT, the STD of total geostrophic speeds dropped to 0.162 m/s.