Analysis of formation pressure test results in the Mount Elbert methane hydrate reservoir through numerical simulation

Targeting the methane hydrate (MH) bearing units C and D at the Mount Elbert prospect on the Alaska North Slope, four MDT (Modular Dynamic Formation Tester) tests were conducted in February 2007. The C2 MDT test was selected for history matching simulation in the MH Simulator Code Comparison Study. Through history matching simulation, the physical and chemical properties of the unit C were adjusted, which suggested the most likely reservoir properties of this unit. Based on these properties thus tuned, the numerical models replicating “Mount Elbert C2 zone like reservoir”, “PBU L-Pad like reservoir” and “PBU L-Pad down dip like reservoir” were constructed. The long term production performances of wells in these reservoirs were then forecasted assuming the MH dissociation and production by the methods of depressurization, combination of depressurization and wellbore heating, and hot water huff and puff. The predicted cumulative gas production ranges from 2.16 × 10⁶ m³/well to 8.22 × 10⁸ m³/well depending mainly on the initial temperature of the reservoir and on the production method.This paper describes the details of modeling and history matching simulation. This paper also presents the results of the examinations on the effects of reservoir properties on MH dissociation and production performances under the application of the depressurization and thermal methods.     

High-resolution well-log derived dielectric properties of gas-hydrate-bearing sediments, Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

A dielectric logging tool, electromagnetic propagation tool (EPT), was deployed in 2007 in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well (Mount Elbert Well), North Slope, Alaska. The measured dielectric properties in the Mount Elbert well, combined with density log measurements, result in a vertical high-resolution (cm-scale) estimate of gas hydrate saturation. Two hydrate-bearing sand reservoirs about 20 m thick were identified using the EPT log and exhibited gas-hydrate saturation estimates ranging from 45% to 85%. In hydrate-bearing zones where variation of hole size and oil-based mud invasion are minimal, EPT-based gas hydrate saturation estimates on average agree well with lower vertical resolution estimates from the nuclear magnetic resonance logs; however, saturation and porosity estimates based on EPT logs are not reliable in intervals with substantial variations in borehole diameter and oil-based invasion.EPT log interpretation reveals many thin-bedded layers at various depths, both above and below the thick continuous hydrate occurrences, which range from 30-cm to about 1-m thick. Such thin layers are not indicated in other well logs, or from the visual observation of core, with the exception of the image log recorded by the oil-base microimager. We also observe that EPT dielectric measurements can be used to accurately detect fine-scale changes in lithology and pore fluid properties of hydrate-bearing sediments where variation of hole size is minimal. EPT measurements may thus provide high-resolution in-situ hydrate saturation estimates for comparison and calibration with laboratory analysis.     

Downhole well log and core montages from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

The BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well was an integral part of an ongoing project to determine the future energy resource potential of gas hydrates on the Alaska North Slope. As part of this effort, the Mount Elbert well included an advanced downhole geophysical logging program. Because gas hydrate is unstable at ground surface pressure and temperature conditions, a major emphasis was placed on the downhole-logging program to determine the occurrence of gas hydrates and the in-situ physical properties of the sediments. In support of this effort, well-log and core data montages have been compiled which include downhole log and core-data obtained from the gas-hydrate-bearing sedimentary section in the Mount Elbert well. Also shown are numerous reservoir parameters, including gas-hydrate saturation and sediment porosity log traces calculated from available downhole well log and core data.     

Gas production from a cold, stratigraphically-bounded gas hydrate deposit at the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Implications of uncertainties

As part of an effort to identify suitable targets for a planned long-term field test, we investigate by means of numerical simulation the gas production potential from unit D, a stratigraphically bounded (Class 3) permafrost-associated hydrate occurrence penetrated in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well on North Slope, Alaska. This shallow, low-pressure deposit has high porosities (? = 0.4), high intrinsic permeabilities (k = 10⁻¹² m²) and high hydrate saturations (S_H = 0.65). It has a low temperature (T = 2.3-2.6 °C) because of its proximity to the overlying permafrost. The simulation results indicate that vertical wells operating at a constant bottomhole pressure would produce at very low rates for a very long period. Horizontal wells increase gas production by almost two orders of magnitude, but production remains low. Sensitivity analysis indicates that the initial deposit temperature is by the far the most important factor determining production performance (and the most effective criterion for target selection) because it controls the sensible heat available to fuel dissociation. Thus, a 1 °C increase in temperature is sufficient to increase the production rate by a factor of almost 8. Production also increases with a decreasing hydrate saturation (because of a larger effective permeability for a given k), and is favored (to a lesser extent) by anisotropy.     

Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Overview of scientific and technical program

The Mount Elbert Gas Hydrate Stratigraphic Test Well was drilled within the Alaska North Slope (ANS) Milne Point Unit (MPU) from February 3 to 19, 2007. The well was conducted as part of a Cooperative Research Agreement (CRA) project co-sponsored since 2001 by BP Exploration (Alaska), Inc. (BPXA) and the U.S. Department of Energy (DOE) in collaboration with the U.S. Geological Survey (USGS) to help determine whether ANS gas hydrate can become a technically and commercially viable gas resource. Early in the effort, regional reservoir characterization and reservoir simulation modeling studies indicated that up to 0.34 trillion cubic meters (tcm; 12 trillion cubic feet, tcf) gas may be technically recoverable from 0.92 tcm (33 tcf) gas-in-place within the Eileen gas hydrate accumulation near industry infrastructure within ANS MPU, Prudhoe Bay Unit (PBU), and Kuparuk River Unit (KRU) areas. To further constrain these estimates and to enable the selection of a test site for further data acquisition, the USGS reprocessed and interpreted MPU 3D seismic data provided by BPXA to delineate 14 prospects containing significant highly-saturated gas hydrate-bearing sand reservoirs. The “Mount Elbert” site was selected to drill a stratigraphic test well to acquire a full suite of wireline log, core, and formation pressure test data. Drilling results and data interpretation confirmed pre-drill predictions and thus increased confidence in both the prospect interpretation methods and in the wider ANS gas hydrate resource estimates. The interpreted data from the Mount Elbert well provide insight into and reduce uncertainty of key gas hydrate-bearing reservoir properties, enable further refinement and validation of the numerical simulation of the production potential of both MPU and broader ANS gas hydrate resources, and help determine viability of potential field sites for future extended term production testing. Drilling and data acquisition operations demonstrated that gas hydrate scientific research programs can be safely, effectively, and efficiently conducted within ANS infrastructure. The program success resulted in a technical team recommendation to project management to drill and complete a long-term production test within the area of existing ANS infrastructure. If approved by stakeholders, this long-term test would build on prior arctic research efforts to better constrain the potential gas rates and volumes that could be produced from gas hydrate-bearing sand reservoirs.     

Pore fluid geochemistry from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

The BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well was drilled and cored from 606.5 to 760.1 m on the North Slope of Alaska, to evaluate the occurrence, distribution and formation of gas hydrate in sediments below the base of the ice-bearing permafrost. Both the dissolved chloride and the isotopic composition of the water co-vary in the gas hydrate-bearing zones, consistent with gas hydrate dissociation during core recovery, and they provide independent indicators to constrain the zone of gas hydrate occurrence. Analyses of chloride and water isotope data indicate that an observed increase in salinity towards the top of the cored section reflects the presence of residual fluids from ion exclusion during ice formation at the base of the permafrost layer. These salinity changes are the main factor controlling major and minor ion distributions in the Mount Elbert Well. The resulting background chloride can be simulated with a one-dimensional diffusion model, and the results suggest that the ion exclusion at the top of the cored section reflects deepening of the permafrost layer following the last glaciation (∼100 kyr), consistent with published thermal models. Gas hydrate saturation values estimated from dissolved chloride agree with estimates based on logging data when the gas hydrate occupies more than 20% of the pore space; the correlation is less robust at lower saturation values. The highest gas hydrate concentrations at the Mount Elbert Well are clearly associated with coarse-grained sedimentary sections, as expected from theoretical calculations and field observations in marine and other arctic sediment cores.     

Formation history and physical properties of sediments from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

The synthesis of available geological information and surface temperature evolution in the Alaska North Slope region suggests that: biogenic and deeper thermogenic gases migrated through fault networks and preferentially invaded coarse-grained layers that have relatively high hydraulic conductivity and low gas entry pressures; hydrate started forming before the beginning of the permafrost; eventually, the permafrost deepened and any remaining free water froze so that ice and hydrate may coexist at some elevations. The single tested specimen (depth 620.47-620.62 m) from the D unit consists of uncemented quartzitic fine sand with a high fraction of fines (56% by mass finer than sieve #200). The as-received specimen shows no evidence of gas present. The surface texture of sediment grains is compatible with a fluvial-deltaic sedimentation environment and shows no signs of glacial entrainment. Tests conducted on sediments with and without THF hydrates show that effective stress, porosity, and hydrate saturation are the major controls on the mechanical and geophysical properties. Previously derived relationships between these variables and mechanical/geophysical parameters properly fit the measurements gathered with Mount Elbert specimens at different hydrate saturations and effective stress levels. We show that these measurements can be combined with index properties and empirical geomechanical relationships to estimate engineering design parameters. Volumetric strains measured during hydrate dissociation vanish at 2-4 MPa; therefore, minimal volumetric strains are anticipated during gas production at the Mount Elbert well. However, volume changes could increase if extensive grain crushing takes place during depressurization-driven production strategies, if the sediment has unexpectedly high in situ porosity associated to the formation history, or if fines migration and clogging cause a situation of sustained sand production.     

Formation pressure testing at the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Operational summary, history matching, and interpretations

In February 2007, the U.S. Department of Energy, BP Exploration (Alaska), and the U.S. Geological Survey, collected open-hole pressure-response data, as well as gas and water sample collection, in a gas hydrate reservoir (the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well) using Schlumberger's Modular Dynamics Formation Tester (MDT) wireline tool. Four such MDT tests, ranging from six to twelve hours duration, and including a series of flow, sampling, and shut-in periods of various durations, were conducted. Locations for the testing were selected based on NMR and other log data to assure sufficient isolation from reservoir boundaries and zones of excess free water. Test stages in which pressure was reduced sufficiently to mobilize free water in the formation (yet not cause gas hydrate dissociation) produced readily interpretable pressure build-up profiles. Build-ups following larger drawdowns consistently showed gas-hydrate dissociation and gas release (as confirmed by optical fluid analyzer data), as well as progressive dampening of reservoir pressure build-up during sequential tests at a given MDT test station.History matches of one multi-stage, 12-h test (the C2 test) were accomplished using five different reservoir simulators: CMG-STARS, HydrateResSim, MH21-HYDRES, STOMP-HYD, and TOUGH + HYDRATE. Simulations utilized detailed information collected across the reservoir either obtained or determined from geophysical well logs, including thickness (11.3 m, 37 ft.), porosity (35%), hydrate saturation (65%), both mobile and immobile water saturations, intrinsic permeability (1000 mD), pore water salinity (5 ppt), and formation temperature (3.3-3.9 °C). This paper will present the approach and preliminary results of the history-matching efforts, including estimates of initial formation permeability and analyses of the various unique features exhibited by the MDT results.     

The characteristics of gas hydrates recovered from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

Systematic analyses have been carried out on two gas hydrate-bearing sediment core samples, HYPV4, which was preserved by CH₄ gas pressurization, and HYLN7, which was preserved in liquid-nitrogen, recovered from the BPXA-DOE-USGS Mount Elbert Stratigraphic Test Well. Gas hydrate in the studied core samples was found by observation to have developed in sediment pores, and the distribution of hydrate saturation in the cores imply that gas hydrate had experienced stepwise dissociation before it was stabilized by either liquid nitrogen or pressurizing gas. The gas hydrates were determined to be structure Type I hydrate with hydration numbers of approximately 6.1 by instrumentation methods such as powder X-ray diffraction, Raman spectroscopy and solid state ¹³C NMR. The hydrate gas composition was predominantly methane, and isotopic analysis showed that the methane was of thermogenic origin (mean δ¹³C = −48.6‰ and δ_D = −248‰ for sample HYLN7). Isotopic analysis of methane from sample HYPV4 revealed secondary hydrate formation from the pressurizing methane gas during storage.     

Pre- and post-drill comparison of the Mount Elbert gas hydrate prospect, Alaska North Slope

In 2006, the United States Geological Survey (USGS) completed a detailed analysis and interpretation of available 2-D and 3-D seismic data, along with seismic modeling and correlation with specially processed downhole well log data for identifying potential gas hydrate accumulations on the North Slope of Alaska. A methodology was developed for identifying sub-permafrost gas hydrate prospects within the gas hydrate stability zone in the Milne Point area. The study revealed a total of 14 gas hydrate prospects in this area.In order to validate the gas hydrate prospecting protocol of the USGS and to acquire critical reservoir data needed to develop a longer-term production testing program, a stratigraphic test well was drilled at the Mount Elbert prospect in the Milne Point area in early 2007. The drilling confirmed the presence of two prominent gas-hydrate-bearing units in the Mount Elbert prospect, and high quality well logs and core data were acquired. The post-drill results indicate pre-drill predictions of the reservoir thickness and the gas-hydrate saturations based on seismic and existing well data were 90% accurate for the upper unit (hydrate unit D) and 70% accurate for the lower unit (hydrate unit C), confirming the validity of the USGS approach to gas hydrate prospecting. The Mount Elbert prospect is the first gas hydrate accumulation on the North Slope of Alaska identified primarily on the basis of seismic attribute analysis and specially processed downhole log data. Post-drill well log data enabled a better constraint of the elastic model and the development of an improved approach to the gas hydrate prospecting using seismic attributes.     

Physical properties of sediment from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

This study characterizes cored and logged sedimentary strata from the February 2007 BP Exploration Alaska, Department of Energy, U.S. Geological Survey (BPXA-DOE-USGS) Mount Elbert Gas Hydrate Stratigraphic Test Well on the Alaska North Slope (ANS). The physical-properties program analyzed core samples recovered from the well, and in conjunction with downhole geophysical logs, produced an extensive dataset including grain size, water content, porosity, grain density, bulk density, permeability, X-ray diffraction (XRD) mineralogy, nuclear magnetic resonance (NMR), and petrography.This study documents the physical property interrelationships in the well and demonstrates their correlation with the occurrence of gas hydrate. Gas hydrate (GH) occurs in three unconsolidated, coarse silt to fine sand intervals within the Paleocene and Eocene beds of the Sagavanirktok Formation: Unit D-GH (614.4 m-627.9 m); unit C-GH1 (649.8 m-660.8 m); and unit C-GH2 (663.2 m-666.3 m). These intervals are overlain by fine to coarse silt intervals with greater clay content. A deeper interval (unit B) is similar lithologically to the gas-hydrate-bearing strata; however, it is water-saturated and contains no hydrate.In this system it appears that high sediment permeability (k) is critical to the formation of concentrated hydrate deposits. Intervals D-GH and C-GH1 have average “plug” intrinsic permeability to nitrogen values of 1700 mD and 675 mD, respectively. These values are in strong contrast with those of the overlying, gas-hydrate-free sediments, which have k values of 5.7 mD and 49 mD, respectively, and thus would have provided effective seals to trap free gas. The relation between permeability and porosity critically influences the occurrence of GH. For example, an average increase of 4% in porosity increases permeability by an order of magnitude, but the presence of a second fluid (e.g., methane from dissociating gas hydrate) in the reservoir reduces permeability by more than an order of magnitude.     

Gas geochemistry of the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Implications for gas hydrate exploration in the Arctic

Gases were analyzed from well cuttings, core, gas hydrate, and formation tests at the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well, drilled within the Milne Point Unit, Alaska North Slope. The well penetrated a portion of the Eileen gas hydrate deposit, which overlies the more deeply buried Prudhoe Bay, Milne Point, West Sak, and Kuparuk River oil fields. Gas sources in the upper 200 m are predominantly from microbial sources (C₁ isotopic compositions ranging from −86.4 to −80.6‰). The C₁ isotopic composition becomes progressively enriched from 200 m to the top of the gas hydrate-bearing sands at 600 m. The tested gas hydrates occur in two primary intervals, units D and C, between 614.0 m and 664.7 m, containing a total of 29.3 m of gas hydrate-bearing sands. The hydrocarbon gases in cuttings and core samples from 604 to 914 m are composed of methane with very little ethane. The isotopic composition of the methane carbon ranges from −50.1 to −43.9‰ with several outliers, generally decreasing with depth. Gas samples collected by the Modular Formation Dynamics Testing (MDT) tool in the hydrate-bearing units were similarly composed mainly of methane, with up to 284 ppm ethane. The methane isotopic composition ranged from −48.2 to −48.0‰ in the C sand and from −48.4 to −46.6‰ in the D sand. Methane hydrogen isotopic composition ranged from −238 to −230‰, with slightly more depleted values in the deeper C sand. These results are consistent with the concept that the Eileen gas hydrates contain a mixture of deep-sourced, microbially biodegraded thermogenic gas, with lesser amounts of thermogenic oil-associated gas, and coal gas. Thermal gases are likely sourced from existing oil and gas accumulations that have migrated up-dip and/or up-fault and formed gas hydrate in response to climate cooling with permafrost formation.     

Microbial community distribution in sediments from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

We studied the microbial communities collected from hydrate-bearing sediments on the North Slope of Alaska to determine how abiotic variables (e.g., grain size, hydrate presence, formation fluid gases) may correspond to the type and distribution of microbes in the sediments. The cores were acquired from sub-permafrost, Eocene (46-55 million year old) sediments in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well within which hydrates are believed to have formed 1.5 mya. Forty samples, eight of which originally contained hydrates, were acquired from depths of ca. 606-666 m below land surface. Five drilling fluid samples acquired from the same depth range were included in the analysis as a control for possible contamination by drilling fluid microbes during the drilling and handling of cores. DNA was extracted from 15 samples (typically <1 ng DNA/g sediment was recovered) and then amplified using polymerase chain reaction with primers specific for bacterial and archaeal 16S rDNA genes, which indicates the likelihood that microbes were present in all analyzed samples. Only bacterial DNA amplicons were detected. Terminal-restriction fragment length polymorphism (T-RFLP) was used to measure bacterial diversity in the respective samples. Non-metric multidimensional scaling (NMS) was used to determine the abiotic variables that may have influenced bacterial diversity. NMS analysis revealed that the microbial taxa present in the sediment were distinct from the taxa present in the drilling fluids suggesting that the sediments were not contaminated by the drilling fluids. Multi-response permutation procedures (MRPP) found no significant difference between three sample groups identified a priori as being from within a hydrate zone, outside of hydrate zone, or on the edge of a hydrate/non-hydrate zone according to downhole nuclear magnetic resonance spectroscopy logs. However, among the several other abiotic parameters that were evaluated mud gas methane concentration and variables related to hydrate presence (e.g., chloride concentration, salinity, and resistivity) appeared to define the arrangement of microbial community signatures in plots resulting from NMS analysis. Communities from hydrate and non-hydrate layers each contained unique taxa as determined by the T-RFLP assay.     

Experimental investigation of gas-water relative permeability for gas-hydrate-bearing sediments from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

Permeability of hydrate reservoirs found in nature is likely to be heavily influenced by the percent of the pore volume occupied by hydrates. The quantification of how hydrate saturation affects permeability is of key interest for reservoir engineering studies. In this study, an experimental setup was modified to test permeability characteristics of unconsolidated core samples containing various saturations of methane hydrates. Hydrates were formed in the unconsolidated samples using a refrigerated core holder connected to a brine and methane injection system. Studies of this type conducted to date have rarely been performed on core samples recovered from actual hydrate-bearing sedimentary sections from natural hydrate intervals. Samples from the Mount Elbert site on the Alaska North Slope (ANS) were used for this study.Relative permeability measurements using hydrate constituent components (e.g. water and methane) are not very desirable due to difficulties in preventing additional hydrate formation during displacement experiments. Relative permeability measurements performed with hydrate constituent components (e.g. water and nitrogen) can help to significantly mitigate issues with additional hydrate formation. However, unsteady state relative permeability experiments produce piston like displacement results suggesting that steady state experiments might be preferable.It was observed that as in previous work using consolidated core samples, permeability of both brine and gases was reduced in unconsolidated hydrate-bearing core samples. Experimental results show that low to moderate hydrate saturations (1.5 to 36%) can significantly reduce permeability of porous media. These saturations, in fact, are lower than hydrate saturations observed in the natural hydrate systems at Mount Elbert.     

Permafrost-associated natural gas hydrate occurrences on the Alaska North Slope

In the 1960s Russian scientists made what was then a bold assertion that gas hydrates should occur in abundance in nature. Since this early start, the scientific foundation has been built for the realization that gas hydrates are a global phenomenon, occurring in permafrost regions of the arctic and in deep water portions of most continental margins worldwide. In 1995, the U.S. Geological Survey made the first systematic assessment of the in-place natural gas hydrate resources of the United States. That study suggested that the amount of gas in the gas hydrate accumulations of northern Alaska probably exceeds the volume of known conventional gas resources on the North Slope. Researchers have long speculated that gas hydrates could eventually become a producible energy resource, yet technical and economic hurdles have historically made gas hydrate development a distant goal. This view began to change in recent years with the realization that this unconventional resource could be developed with existing conventional oil and gas production technology. One of the most significant developments was the completion of the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well on the Alaska North Slope, which along with the Mallik project in Canada, have for the first time allowed the rational assessment of gas hydrate production technology and concepts. Almost 40 years of gas hydrate research in northern Alaska has confirmed the occurrence of at least two large gas hydrate accumulations on the North Slope. We have also seen in Alaska the first ever assessment of how much gas could be technically recovered from gas hydrates. However, significant technical concerns need to be further resolved in order to assess the ultimate impact of gas hydrate energy resource development in northern Alaska.     

Environmental significance of dinoflagellate cysts from the proximal part of the Po-river discharge plume (off southern Italy,Eastern Mediterranean)

To determine the relationship between region specific dinoflagellate cyst distribution in the Po-river discharge area and oceanic environmental conditions, surface sediments of 48 sites in the middle and distal part of the discharge plume area have been studied. Establishing such a relationship is a prerequisite to create reconstructions of the eutrophication history as well as the palaeoclimatic and palaeoceanography history of the area.Literature based information about the sedimentation rates based on ²¹⁰Pb dating methods are available for 18 sites. This enables the calculation of cyst accumulation rates of individual cyst species which reflect their cyst production. Correlation of the accumulation rates of individual species with environmental parameters of the upper waters allows us to adapt and refine the ecological characteristics of a selection of cyst species. This latter is trivial since the current concepts on the ecological significance of dinoflagellate cyst have to be revised as a result of the current developments in the dinoflagellate research field. These developments have elucidated that a considerable part of the relative abundance datasets that form the basis for the present day ecological concepts of dinoflagellate cysts might have suffered from so called “closed sum effects” and have been overprinted by early diagenetic processes.The dinoflagellate cyst association reflects both upper and bottom water circulation. Based on the relative abundance data four associations can be distinguished that are characteristic for the major oceanographic settings in the region. (1) River discharge association. This association consists of Echinidinium spp., Lejeunecysta sabrina, Lingulodinium machaerophorum, Polykrikos kofoidii, Polykrikos schwarzii, cysts of Protoperidinium stellatum, Selenopemphix quanta and reworked cysts. These species have high relative abundances in sites where bottom waters are low in oxygen and upper waters are influenced by river discharge waters that are characterized by high productivity and relative low salinity. (2) Warm water association. This association consists of Spiniferites mirabilis, Spiniferites pachydermus, Spiniferites ramosus and Spiniferites spp. which have their highest relative abundances in the sites at the plume margin that are characterized by relative warm upper waters and intermediate chlorophyll-a concentrations. (3) Oxygenated bottom water group. Species of this group; Impagidinium aculeatum, Impagidinium patulum, Impagidinium sphaericum, Operculodinium centrocarpum and Operculodinium israelianum have their highest relative abundances at sites where bottom waters are formed by well ventilated Adriatic Deep Water or Eastern Mediterranean Deep Water. (4) Golfo di Taranto group consisting of round brown cysts produced by Protoperidinium species (grouped as Brigantedinium spp.).The variation in accumulation rates can be related to gradiental changes in the trophic state of the surface waters linked to river outflow. Most species show a positive relationship between cyst production and nutrient/trace element availability in upper waters. No negative correlation between cyst production and nutrient/trace element availability could be documented. Production of Brigantidinium spp., Echinidinium spp., L. sabrina, L. machaerophorum, P. kofoidii/schwarzii, Spiniferites spp., S. mirabilis and S. quanta shows the most pronounced increase with increasing nutrient/trace element availability. These species can be considered as valuable indicators for reconstructing changes in the trophic state of the upper waters within the Po-river area in palaeo-environmental studies.     

Gas hydrate characterization and grain-scale imaging of recovered cores from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

Using cryogenic scanning electron microscopy (CSEM), powder X-ray diffraction, and gas chromatography methods, we investigated the physical states, grain characteristics, gas composition, and methane isotopic composition of two gas-hydrate-bearing sections of core recovered from the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well situated on the Alaska North Slope. The well was continuously cored from 606.5 m to 760.1 m depth, and sections investigated here were retrieved from 619.9 m and 661.0 m depth. X-ray analysis and imaging of the sediment phase in both sections shows it consists of a predominantly fine-grained and well-sorted quartz sand with lesser amounts of feldspar, muscovite, and minor clays. Cryogenic SEM shows the gas-hydrate phase forming primarily as a pore-filling material between the sediment grains at approximately 70-75% saturation, and more sporadically as thin veins typically several tens of microns in diameter. Pore throat diameters vary, but commonly range 20-120 microns. Gas chromatography analyses of the hydrate-forming gas show that it is comprised of mainly methane (>99.9%), indicating that the gas hydrate is structure I. Here we report on the distribution and articulation of the gas-hydrate phase within the cores, the grain morphology of the hydrate, the composition of the sediment host, and the composition of the hydrate-forming gas.     

Integrated biochemical,molecular genetic,and bioacoustical analysis of mesoscale variability of the euphausiid Nematoscelis difficilis in the California Current

Integrated assessment of the euphausiid Nematoscelis difficilis (Crustacea; Euphausiacea) and the zooplankton assemblage of the California Current was designed to investigate individual, population, and community responses to mesoscale variability in biological and physical characters of the ocean. Zooplankton samples and observational data were collected along a cross-shelf transect of the California Current in association with the California Cooperative Fisheries Investigations (CalCOFI) Survey during October 1996. The transect crossed three domains defined by temperature and salinity: nearshore, mid-Current, and offshore. Individual N. difficilis differed in physiological condition along the transect, with higher size-corrected concentrations of four central metabolic enzymes (citrate synthetase, hexokinase, lactate dehydrogenase (LDH), and phosphoglucose isomerase (PGI)) for euphausiids collected in nearshore waters than in mid-Current and offshore waters. There was little variation in the DNA sequences of the genes encoding PGI and LDH (all DNA changes were either silent or heterozygous base substitutions), suggesting that differences in enzyme concentration did not result from underlying molecular genetic variation. The population genetic makeup of N. difficilis varied from sample to sample based on haplotype frequencies of mitochondrial cytochrome oxidase I (mtCOI; P=0.029). There were significant differences between pooled nearshore and offshore samples, based on allele frequencies at two sites of common substitutions in the mtCOI sequence (P=0.020 and 0.026). Silhouette and bioacoustical backscattering measurements of the zooplankton assemblage of the top 100 m showed marked diel vertical migration of the scattering layer, of which euphausiids were a small but significant fraction. The biochemical and molecular assays are used as indices of complex physiological (i.e., growth and condition) and genetic (i.e., mortality) processes; the bioacoustical observations provide insight into the ecosystem context for the single-species measurements. All data are intended for integration into predictive models of secondary production and biomass concentration in the ocean.