Controls on spatial and temporal variations in sand delivery to salmonid spawning riffles

Fine sediment infiltration into gravel interstices is known to be detrimental to incubating salmonid embryos. Infiltration into spawning riffles can show large spatial variations at the scale of a morphological unit and over time, with significant implications for embryo survival. Furthermore, some process‐based infiltration studies, and incubation‐to‐emergence models assume that fines are delivered to redds via suspension rather than bedload. This process‐based 12‐month study examined spatial patterns of predominantly sand infiltration into gravels in an upland trout stream, using infiltration baskets. An assessment of Rouse numbers for infiltrated sand indicated that it was transported predominantly as bedload at flow peaks. Clear temporal and spatial patterns existed, with highest rates of infiltration strongly associated with higher discharges (r² = 0.7, p < .05). Seasonal variations in the delivery of different grain sizes were also a feature, with enhanced contributions of 0.5–2 mm sediment during elevated winter flows and 0.125–0.5 mm sediment during spring and summer; the latter is potentially harmful to the later stages of embryo incubation. Clear spatial patterns were also evident across riffles, with highest rates of infiltration tending to occur in areas of lower relative roughness—the areas competent to transport sand for longer periods. Incubation‐to‐emergence models should take into consideration spatial patterns of fine sediment dynamics at the pool–riffle scale, to improve prediction.     

A remote controlled freeze corer for sampling unconsolidated surface sediments

A new coring device is presented which allows the recovery of loose watery surface sediments and the water/sediment interface byin situ freezing, resulting in well preserved samples. The instrument consists of a tripod with adjustable legs, a hydraulic system, an insulated thermos (with two electrical pumps), and a wedge-shaped freeze box. Alcohol chilled with dry ice is the freezing agent. The corer can be deployed from a boat or a raft and permits recovery of undisturbed surface sediment sections up to 100 cm long in deep waters. The corer is particularly useful for sampling varved sediments.     

Cryogenic Core Collection and Preservation of Subsurface Samples for Biomolecular Analysis

A cryogenic coring system for the collection and preservation of biomolecules in unconsolidated subsurface solid samples is presented here. The sampler is based on existing direct‐push coring technology, with the addition of a cryogenic step to freeze the sample in situ. Once brought to the surface, the frozen cores can be packed in dry ice and shipped to the laboratory for further processing and analysis. The approach prevents redistribution of fluids during sample recovery and shipping, and because the cores are frozen in situ there is little loss of solid material during retrieval to ground surface. To evaluate the performance of the approach, DNA analyses of samples collected by cryogenic coring in a very large physical model are compared with results from water samples and horizontal core samples taken in close proximity. The data indicate that the vertical distribution of DNA within the cryogenic core can be measured at the centimeter scale, providing unprecedented characterization of subsurface biogeochemical interfaces.     

Time‐integrated sampling of fluvial suspended sediment: a simple methodology for small catchments

Fine‐grained (<62·5 µm) suspended sediment transport is a key component of the geochemical flux in most fluvial systems. The highly episodic nature of suspended sediment transport imposes a significant constraint on the design of sampling strategies aimed at characterizing the biogeochemical properties of such sediment. A simple sediment sampler, utilizing ambient flow to induce sedimentation by settling, is described. The sampler can be deployed unattended in small streams to collect time‐integrated suspended sediment samples. In laboratory tests involving chemically dispersed sediment, the sampler collected a maximum of 71% of the input sample mass. However, under natural conditions, the existence of composite particles or flocs can be expected to increase significantly the trapping efficiency. Field trials confirmed that the particle size composition and total carbon content of the sediment collected by the sampler were representative statistically of the ambient suspended sediment. Copyright © 2000 John Wiley & Sons, Ltd.     

Composite suspended sediment particles in river systems: their incidence,dynamics and physical characteristics

Most of the existing data on the effective particle size characteristics of fluvial suspended sediment derive from instantaneous sampling methods that may not be representative of the overall suspended sediment loads. This presents difficulties when there is a need to incorporate effective particle size data into numerical models of floodplain sedimentation and sediment‐associated contaminant transfer. We have used a field‐based water elutriation apparatus (WEA) to assemble a large (36 flood) database on the time‐integrated nature of the effective and absolute particle size characteristics of suspended sediment in four subcatchments of the River Exe basin of southwest England. These catchments encompass a wide range of terrains and fluvial environments that are broadly representative of much of the UK and temperate, low relief northwest Europe. The WEA provides important data on the physical characteristics of composite particles that are not attainable using other methods. This dataset has allowed, for the first time, detailed interbasin comparisons of the time‐integrated particle size characteristics of suspended sediment and reliable estimates of the contribution of five effective size classes to the mean annual suspended sediment load of the study catchments. The suspended sediment load of each river is dominated by composite rather than primary particles, with, for example, almost 60% (by mass) of the sediment load of the River Exe at Thorverton transported as composite particles > 16 µm in size. All the effective size classes contain significant clay components. A key outcome of this study is the recognition that each catchment has a distinctive time‐integrated effective particle size signature. In addition, the time‐integrated effective particle size characteristics of the suspended loads in each of the catchments display much greater spatial variability than the equivalent absolute particle size distributions. This indicates that the processes producing composite particles vary significantly between these catchments, and this has important implications for our understanding of the dynamics of suspended sediment properties. Copyright © 2007 John Wiley & Sons, Ltd.     

The composite method: an improved method for stream‐water solute load estimation

The composite method is an alternative method for estimating stream‐water solute loads, combining aspects of two commonly used methods: the regression‐model method (which is used by the composite method to predict variations in concentrations between collected samples) and a period‐weighted approach (which is used by the composite method to apply the residual concentrations from the regression model over time). The extensive dataset collected at the outlet of the Panola Mountain Research Watershed (PMRW) near Atlanta, Georgia, USA, was used in data analyses for illustrative purposes. A bootstrap (subsampling) experiment (using the composite method and the PMRW dataset along with various fixed‐interval and large storm sampling schemes) obtained load estimates for the 8‐year study period with a magnitude of the bias of less than 1%, even for estimates that included the fewest number of samples. Precisions were always <2% on a study period and annual basis, and <2% precisions were obtained for quarterly and monthly time intervals for estimates that had better sampling. The bias and precision of composite‐method load estimates varies depending on the variability in the regression‐model residuals, how residuals systematically deviated from the regression model over time, sampling design, and the time interval of the load estimate. The regression‐model method did not estimate loads precisely during shorter time intervals, from annually to monthly, because the model could not explain short‐term patterns in the observed concentrations. Load estimates using the period‐weighted approach typically are biased as a result of sampling distribution and are accurate only with extensive sampling. The formulation of the composite method facilitates exploration of patterns (trends) contained in the unmodelled portion of the load. Copyright © 2006 John Wiley & Sons, Ltd.     

Ambient Changes in Tracer Concentrations from a Multilevel Monitoring System in Basalt

Starting in 2008, a 4‐year tracer study was conducted to evaluate ambient changes in groundwater concentrations of a 1,3,6‐naphthalene trisulfonate tracer that was added to drill water. Samples were collected under open borehole conditions and after installing a multilevel groundwater monitoring system completed with 11 discrete monitoring zones within dense and fractured basalt and sediment layers in the eastern Snake River aquifer. The study was done in cooperation with the U.S. Department of Energy to test whether ambient fracture flow conditions were sufficient to remove the effects of injected drill water prior to sample collection. Results from thief samples indicated that the tracer was present in minor concentrations 28 days after coring, but was not present 6 months after coring or 7 days after reaming the borehole. Results from sampling the multilevel monitoring system indicated that small concentrations of the tracer remained in 5 of 10 zones during some period after installation. All concentrations were several orders of magnitude lower than the initial concentrations in the drill water. The ports that had remnant concentrations of the tracer were either located near sediment layers or were located in dense basalt, which suggests limited groundwater flow near these ports. The ports completed in well‐fractured and vesicular basalt had no detectable concentrations.     

Riffle‐pool morphometry and stage‐dependant morphodynamics of a large floodplain river (Vereinigte Mulde,Sachsen‐Anhalt,Germany)

Riffle‐pool sequences are a common feature of gravel‐bed rivers. However, mechanisms of their generation and maintenance are still not fully understood. In this study a monitoring approach is employed that focuses on analysing cross‐sectional and longitudinal channel geometry of a large floodplain river (Vereinigte Mulde, Sachsen‐Anhalt, Germany) with a high temporal and spatial resolution, in order to conclude from stage‐dependant morphometric changes to riffle and pool maintaining processes. In accordance with previous authors, pool cross‐sections of the Mulde River are narrow and riffle cross‐sections are wide suggesting that they should rather be addressed as two general types of channel cross‐sections than solely as bedforms. At high flows, riffles and pools in the study reaches changed in length and height but not in position. Pools were scoured and riffles aggraded, a development which was reversed during receding flows below the threshold of 0·4Q_bf (40% bankfull discharge). An index for the longitudinal amplitude of riffle‐pool sequences, the bed undulation intensity or bedform amplitude, is introduced and proved to be highly significant as a form parameter, its first derivative as a process parameter. The process of pool scour and riffle fill is addressed as bedform maintenance or bedform accentuation. It is indicated by increasing longitudinal bed amplitudes. According to the observed dynamics of bed amplitudes, maintenance of riffle‐pool sequences lags behind discharge peaks. Maximum bed amplitudes may be reached with a delay of several days after peak discharges. Increasing bed undulation intensity is interpreted to indicate bed mobility. Post‐flood decrease of the bed undulation intensity indicates a retrograde phase when transport from pools to riffles has ceased and bed mobility is restricted to riffle tails and heads of pools. This type of transport behaviour is referred to as disconnected mobility. The comparison of two river reaches, one with undisturbed sediment supply, the other with sediment deficit, suggests that high bed undulation intensity values at low flows indicate sediment deficit and potentially channel degrading conditions. It is more generally hypothesized that channel bed undulations constitute a major component of form roughness and that increased bed amplitudes are an important feature of channel bed adjustment to sediment deficit be it temporally during late floods or permanently due to a supply limitation of bedload. Copyright © 2011 John Wiley & Sons, Ltd.     

Evaluation of a simple,inexpensive, in situ sampler for measuring time‐weighted average concentrations of suspended sediment in rivers and streams

The accurate measurement of suspended sediment (<200 μm) in aquatic environments is essential to understand and effectively manage changes to sediment, nutrient, and contaminant concentrations on both temporal and spatial scales. Commonly used sampling techniques for suspended sediment either lack the ability to accurately measure sediment concentration (e.g., passive sediment samplers) or are too expensive to deploy in sufficient number to provide landscape‐scale information (e.g., automated discrete samplers). Here, we evaluate a time‐integrated suspended sediment sampling technique, the pumped active suspended sediment (PASS) sampler, which collects a sample that can be used for the accurate measurement of time‐weighted average (TWA) suspended sediment concentration and sediment particle size distribution. The sampler was evaluated against an established passive time‐integrated suspended sediment sampling technique (i.e., Phillips sampler) and the standard discrete sampling method (i.e., manual discrete sampling). The PASS sampler collected a sample representative of TWA suspended sediment concentration and particle size distribution of a control sediment under laboratory conditions. Field application of the PASS sampler showed that it collected a representative TWA suspended sediment concentration and particle size distribution during high flow events in an urban stream. The particle size distribution of sediment collected by the PASS and Phillips samplers were comparable and the TWA suspended sediment concentration of the samples collected using the PASS and discrete sampling techniques agreed well, differing by only 4% and 6% for two different high flow events. We should note that the current configuration of the PASS sampler does not provide a flow‐weighted measurement and, therefore, is not suitable for the determination of sediment loads. The PASS sampler is a simple, inexpensive, and robust in situ sampling technique for the accurate measurement of TWA suspended sediment concentration and particle size distribution.     

Spatial variations in surface sediment structure in riffle–pool sequences: a preliminary test of the Differential Sediment Entrainment Hypothesis (DSEH)

Riffle–pool sequences are maintained through the preferential entrainment of sediment grains from pools rather than riffles. This preferential entrainment has been attributed to a reversal in the magnitude of velocity and shear stress under high flows; however the Differential Sediment Entrainment Hypothesis (DSEH) postulates that differential entrainment can instead result from spatial sedimentological contrasts. Here we use a novel suite of in situ grain‐scale field measurements from a riffle–pool sequence to parameterize a physically‐based model of grain entrainment. Field measurements include pivoting angles, lift forces and high resolution digital elevation models (DEMs) acquired using terrestrial laser scanning, from which particle exposure, protrusion and surface roughness were derived. The entrainment model results show that grains in pools have a lower critical entrainment shear stress than grains in either pool exits or riffles. This is because pool grains have looser packing, hence greater exposure and lower pivoting angles. Conversely, riffle and pool exit grains have denser packing, lower exposure and higher pivoting angles. A cohesive matrix further stabilizes pool exit grains. The resulting predictions of critical entrainment shear stress for grains in different subunits are compared with spatial patterns of bed shear stress derived from a two‐dimensional computational fluid dynamics (CFD) model of the reach. The CFD model predicts that, under bankfull conditions, pools experience lower shear stresses than riffles and pool exits. However, the difference in sediment entrainment shear stress is sufficiently large that sediment in pools is still more likely to be entrained than sediment in pool exits or riffles, resulting in differential entrainment under bankfull flows. Significantly, this differential entrainment does not require a reversal in flow velocities or shear stress, suggesting that sedimentological contrasts alone may be sufficient for the maintenance of riffle–pool sequences. This finding has implications for the prediction of sediment transport and the morphological evolution of gravel‐bed rivers. Copyright © 2012 John Wiley & Sons, Ltd.     

Sediment and fluvial particulate carbon flux from an eroding peatland catchment

Erosion and the associated loss of carbon is a major environmental concern in many peatlands and remains difficult to accurately quantify beyond the plot scale. Erosion was measured in an upland blanket peatland catchment (0.017 km²) in northern England using structure-from-motion (SfM) photogrammetry, sediment traps and stream sediment sampling at different spatial scales. A net median topographic change of –27 mm yr^–1 was recorded by SfM over the 12-month monitoring period for the entire surveyed area (598 m²). Within the entire surveyed area there were six nested catchments where both SfM and sediment traps were used to measure erosion. Substantial amounts of peat were captured in sediment traps during summer storm events after two months of dry weather where desiccation of the peat surface occurred. The magnitude of topographic change for the six nested catchments determined by SfM (mean value: 5.3 mm, standard deviation: 5.2 mm) was very different to the areal average derived from sediment traps (mean value: –0.3 mm, standard deviation: 0.1 mm). Thus, direct interpolation of peat erosion from local net topographic change into sediment yield at the catchment outlet appears problematic. Peat loss measured at the hillslope scale was not representative of that at the catchment scale. Stream sediment sampling at the outlet of the research catchment (0.017 km²) suggested that the yields of suspended sediment and particulate organic carbon were 926.3 t km^–2 yr^–1 and 340.9 t km^–2 yr^–1, respectively, with highest losses occurring during the autumn. Both freeze–thaw during winter and desiccation during long periods of dry weather in spring and summer were identified as important peat weathering processes during the study. Such weathering was a key enabler of subsequent fluvial peat loss from the catchment. © 2019 John Wiley & Sons, Ltd.     

The use of short‐lived radionuclides to quantify transitional bed material transport in a regulated river

We investigate the use of the short‐lived fallout radionuclide beryllium‐7 (⁷Be; t_1/2 = 53·4 days) as a tracer of medium and coarse sand (0·25–2 mm), which transitions between transport in suspension and as bed load, and evaluate the effects of impoundment on seasonal and spatial variations in bed sedimentation. We measure ⁷Be activities in approximately monthly samples from point bar and streambed sediments in one unregulated and one regulated stream. In the regulated stream our sampling spanned an array of flow and management conditions during the annual transition from flood control in the winter and early spring to run‐of‐the‐river operation from late spring to autumn. Sediment stored behind the dam during the winter quickly became depleted in ⁷Be activity. This resulted in a pulse of ‘dead’ sediment released when the dam gates were opened in the spring which could be tracked as it moved downstream. Measured average sediment transport velocities (30–80 metres per day (m d^?1)) exceed those typically reported for bulk bed load transport and are remarkably constant across varied flow regimes, possibly due to corresponding changes in bed sand fraction. Results also show that the length scale of the downstream impact of dam management on sediment transport is short (c. 1 km); beyond this distance the sediment trapped by the dam is replaced by new sediment from tributaries and other downstream sources. Copyright © 2006 John Wiley & Sons, Ltd.     

Procedures for Sampling Deep Subsurface Microbial Communities in Unconsolidated Sediments

A corehole sampling project utilizing a wireline coring system provided sediment samples for microbiological characterization from deep unconsolidated sediments. Sampling tools were developed or modified to minimize contamination during sample acquisition and to facilitate stringent decontamination requirements. Quality assurance procedures, including the use of tracers, were implemented to minimize and quantify contamination from drilling hardware, drilling fluids and sample processing. Tracers included microspheres, potassium bromide, rhodamine dye, and perfluorocarbons, which enabled the detection and measurement of 1mg of drilling fluid per kg of sediment. In addition, sample processing was performed on-site in an anaerobic chamber to prevent exposure of the subsurface materials to atmospheric oxygen concentrations. Sediment samples were then disbursed to investigators at National Laboratories and universities funded through the Department of Energy Subsurface Science Microbiology Program for microbiological characterization. Results of these efforts demonstrated that representative subsurface samples were collected and disbursed.     

Perturbation of fluvial sediment fluxes following the 2008 Wenchuan earthquake

Quantifying the removal of co‐seismic landslide material after a large‐magnitude earthquake is central to our understanding of geomorphic recovery from seismic events and the topographic evolution of tectonically active mountain ranges. In order to gain more insight into the fluvial erosion response to co‐seismic landslides, we focus on the sediment fluxes of rivers flowing through the rupture zone of the 2008 M_w 7.9 Wenchuan earthquake in the Longmen Shan of the eastern Tibetan Plateau. Over the post‐seismic period of 2008–2013, we annually collected river sediment samples (0.25–1 mm) at 19 locations and measured the concentration of cosmogenic ¹⁰Be in quartz. When compared with published pre‐earthquake data, the ¹⁰Be concentrations declined dramatically after the earthquake at all sampling sites, but with significant spatial differences in the amplitude of this decrease, and were starting to increase toward pre‐earthquake level in several basins over the 5‐year survey. Our analysis shows that the amplitude of ¹⁰Be decrease is controlled by the amount of landslides directly connected to the river network. Calculations based on ¹⁰Be mixing budgets indicate that the sediment flux of the 0.25–1 mm size fraction increased up to sixfold following the Wenchuan earthquake. Our results also suggest that fluvial erosion became supply limited shortly after the earthquake, and predict that it could take a few years to several decades for fluvial sediment fluxes to go back to pre‐earthquake characteristics, depending on catchment properties. We also estimate that it will take at least decades and possibly up to thousands of years to remove the co‐seismic landslide materials from the catchments in the Longmen Shan. Copyright © 2017 John Wiley & Sons, Ltd.     

Texture‐based image segmentation applied to the quantification of superficial sand in salmonid river gravels

The presence of ?ne sediment in river gravels is widely recognized as being detrimental to salmonid habitat quality. In order to facilitate quanti?cation of sand presence at larger scales, this paper presents an application of image processing allowing for rapid and accurate assessments of super?cial sand presence in dry exposed ?uvial gravels. Images for the process are acquired with a 35 mm SLR ?lm camera and then scanned with a desktop scanner. Texture‐based segmentation is then applied to differentiate between sand and clast areas. Results show that the method is accurate and therefore it offers an alternative to bulk sampling in cases where rapid assessments of sand presence are required. Copyright © 2005 John Wiley & Sons, Ltd.     

The effects of sample scheduling and sample numbers on estimates of the annual fluxes of suspended sediment in fluvial systems

Since the 1970s, there has been both continuing and growing interest in developing accurate estimates of the annual fluvial transport (fluxes and loads) of suspended sediment and sediment‐associated chemical constituents. This study provides an evaluation of the effects of manual sample numbers (from 4 to 12 year^?1) and sample scheduling (random‐based, calendar‐based and hydrology‐based) on the precision, bias and accuracy of annual suspended sediment flux estimates. The evaluation is based on data from selected US Geological Survey daily suspended sediment stations in the USA and covers basins ranging in area from just over 900 km² to nearly 2 million km² and annual suspended sediment fluxes ranging from about 4 Kt year^?1 to about 200 Mt year^?1. The results appear to indicate that there is a scale effect for random‐based and calendar‐based sampling schemes, with larger sample numbers required as basin size decreases. All the sampling schemes evaluated display some level of positive (overestimates) or negative (underestimates) bias. The study further indicates that hydrology‐based sampling schemes are likely to generate the most accurate annual suspended sediment flux estimates with the fewest number of samples, regardless of basin size. This type of scheme seems most appropriate when the determination of suspended sediment concentrations, sediment‐associated chemical concentrations, annual suspended sediment and annual suspended sediment‐associated chemical fluxes only represent a few of the parameters of interest in multidisciplinary, multiparameter monitoring programmes. The results are just as applicable to the calibration of autosamplers/suspended sediment surrogates currently used to measure/estimate suspended sediment concentrations and ultimately, annual suspended sediment fluxes, because manual samples are required to adjust the sample data/measurements generated by these techniques so that they provide depth‐integrated and cross‐sectionally representative data. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.     

Variation in the sediment deposition behind check‐dams under different soil erosion conditions on the Loess Plateau,China

To maintain a reasonable sediment regulation system in the middle reaches of the Yellow River, it is critical to determine the variation in sediment deposition behind check‐dams for different soil erosion conditions. Sediment samples were collected by using a drilling machine in the Fangta watershed of the loess hilly–gully region and the Manhonggou watershed of the weathered sandstone hilly–gully (pisha) region. On the basis of the check‐dam capacity curves, the soil bulk densities and the couplet thickness in these two small watersheds, the sediment yields were deduced at the watershed scale. The annual average sediment deposition rate in the Manhonggou watershed (702.0 mm/(km²·a)) from 1976 to 2009 was much higher than that in the Fangta watershed (171.6 mm/(km²·a)) from 1975 to 2013. The soil particle size distributions in these two small watersheds were generally centred on the silt and sand fractions, which were 42.4% and 50.7% in the Fangta watershed and 60.6% and 32.9% in the Manhonggou watershed, respectively. The annual sediment deposition yield exhibited a decreasing trend; the transition years were 1991 in the Fangta watershed and 1996 in the Manhonggou watershed (P < 0.05). In contrast, the annual average sediment deposition yield was much higher in the Manhonggou watershed (14011.1 t/(km²·a)) than in the Fangta watershed (3149.6 t/(km²·a)). In addition, the rainfalls that induced sediment deposition at the check‐dams were greater than 30 mm in the Fangta watershed and 20 mm in the Manhonggou watershed. The rainfall was not the main reason for the difference in the sediment yield between the two small watersheds. The conversion of farmland to forestland or grassland was the main reason for the decrease in the soil erosion in the Fangta watershed, while the weathered sandstone and bare land were the main factors driving the high sediment yield in the Manhonggou watershed. Knowledge of the sediment deposition process of check‐dams and the variation in the catchment sediment yield under different soil erosion conditions can serve as a basis for the implementation of improved soil erosion and sediment control strategies, particularly in semi‐arid hilly–gully regions. Copyright © 2018 John Wiley & Sons, Ltd.     

Tree Coring as a Complement to Soil Gas Screening to Locate PCE and TCE Source Zones and Hot Spots

Preliminary risk assessment for prioritisation of site investigations requires efficient screening to reveal type and level of contamination. The screening methods, tree coring and soil gas sampling were applied and compared at two forested sites contaminated with tetrachloroethylene (PCE) or trichloroethylene (TCE) to evaluate their ability to locate source zones and contaminant hot spots. One test site represented a relatively homogeneous sandy soil and aquifer, and the second a more heterogeneous geology with both sandy and less permeable clay till layers overlying a chalk aquifer. Tree cores from different tree species were sampled and analysed, and compared to soil gas measurements and existing soil gas data. Both methods were found useful as screening tools to locate hot spots of PCE and TCE in the shallow subsurface. Tree coring was found to be particularly beneficial as a complement to soil gas sampling at sites with low permeable soils, and where contamination was located in the capillary rise or shallow groundwater. The shorter time required for tree coring reduced the costs compared to soil gas sampling, but the sensitivity and precision of tree coring were lower. However, this did not affect the feasibility of using tree coring to locate the hot spots. Moreover, a combination of the two methods can help to focus any subsequent investigations like soil or groundwater sampling. The use of tree coring to complement soil gas sampling for pre‐screening is expected to result in higher certainty for revealing hot spots and source zones at contaminated sites.     

The bedform morphology of Chinese sturgeon spawning sites in the Yangtze River

Quantitative measures of the relationships between channel morphology and the habitat use of Chinese sturgeon(Acipenser sinensis) can help management and regulatory agencies to quantify potential spawning habitats and develop recovery goals in view of the decreasing area of sturgeon spawning habitat.This study determined the specific bedform types at the pool-riffle scale and evaluated the slopes,aspects and bed load gradation composition of Chinese sturgeon spawning areas in the Yangtze River,China.A bedform differencing technique was used to objectively quantify the longitudinal riverbed profile into four distinct pool-riffle units that were independent of discharge.The vertical location of thalweg points within these units was quantified with a riffle proximity index.Chinese sturgeon spawning areas were mapped and correlated with the pool-riffle units,slopes and aspects.The results indicate that Chinese sturgeon spawning areas occur primarily in riffles.The majority of Chinese sturgeon spawning occurred at elevations greater than 75%of the difference in elevation between the nearest riffle crest and the pool bottom.The slope of spawning sites was distributed between 0.05 and 6.36,and the average aspects were 219.92 and 207.63,respectively.The bed load is mainly composted of gravel and pebble,sediment diameter concentrated on 50-500mm.These analyses of bedform morphology will assist regional fish managers in quantifying existing and potential Chinese sturgeon spawning habitats and will provide a quantitative framework for evaluating general ecological implications of channel morphology in the Yangtze River.