Hydraulic characteristics of a small Coastal Plain stream of the southeastern United States: effects of hydrology and season

Various physical and biological properties affect solute transport patterns in streams. We measured hydraulic characteristics of Payne Creek, a low‐gradient upper Coastal Plain stream, using tracer experiments and parameter estimation with OTIS‐P (one‐dimensional transport with inflow and storage with parameter optimization). The primary objective of this study was to estimate the effects of varying discharge, season, and litter accumulation on hydraulic parameters. Channel area A ranged from 0·081 to 0·371 m² and transient storage area A_s ranged from 0·027 to 0·111 m². Dispersion D ranged from 1·5 to 11·1 m² min⁻¹ and exchange coefficient α ranged from 0·009 to 0·038 min⁻¹. Channel area and dispersion were positively correlated to discharge Q, whereas storage area and exchange coefficient were not. Relative storage size A_s/A ranged from 0·17 to 0·59, and was higher during fall than other seasons under a similar Q. The fraction of median travel time due to transient storage ranged from 8·8 to 34·5% and was significantly correlated with Q through a negative power function. Both metrics indicated that transient storage was a significant component affecting solute transport in Payne Creek, especially during the fall. Comparison between the measured channel area A_c and A suggested that surface storage was dominant in Payne Creek. During fall, accumulation of leaf litter resulted in larger A and A_s and lower velocity and D than during other seasons with similar discharge. Seasonal changes in discharge and organic matter accumulation, and dynamic channel morphology affected the magnitude of transient storage and overall hydraulic characteristics of Payne Creek. Copyright © 2005 John Wiley & Sons, Ltd.     

Micro-erosion meter measurements of travertine deposition rates: a case study from Louie Creek,Northwest Queensland,Australia

Although originally designed to measure surface denudation, the micro-erosion meter (MEM) can be adapted easily to measure deposition rates of chemical sediments such as travertines and speleothems. At Louie Creek, northwest Queensland, Australia, travertine deposition rates measured using the MEM average 4·15 mm a⁻¹. However, this figure masks considerable rate variability. Both purely hydraulic and hydraulically related variables appear to be the major mechanisms controlling deposition rates. The most rapid rates occur within relatively high-energy hydraulic regimes (impact and flow zones), whilst deposition rates in pools separating individual travertine barrages (standing water zones) are relatively slow. Dsposition rate variations within spray and impact zones are related directly to discharge. The highest rates in flow zones correlate with the incorporation into the travertine of in situ and allochthonous biogenic material, such as caddis fly larvae, green algal mats and phytoclasts, which proliferate or are entrapped easily under such hydraulic conditions. Considerable spatial variability in deposition rates also prevails. The highest rates for a given set of hydraulic conditions occur at two sites, the Upper Everglades and the Lower Everglades. The MEM also measures net erosion of travertines. At Louie Creek, most of the travertine erosion occurs in the wet season and is confined primarily to standing water zones. © 1997 John Wiley & Sons, Ltd.     

Prediction of concentrated flow width in ephemeral gully channels

Empirical prediction equations of the form W = aQ^b have been reported for rills and rivers, but not for ephemeral gullies. In this study six experimental data sets are used to establish a relationship between channel width (W, m) and flow discharge (Q, m³ s^?1) for ephemeral gullies formed on cropland. The resulting regression equation (W = 2·51 Q^0·412; R² = 0·72; n = 67) predicts observed channel width reasonably well. Owing to logistic limitations related to the respective experimental set ups, only relatively small runoff discharges (i.e. Q < 0·02 m³s^?1) were covered. Using field data, where measured ephemeral gully channel width was attributed to a calculated peak runoff discharge on sealed cropland, the application field of the regression equation was extended towards larger discharges (i.e. 5 × 10^?4m³s^?1 < Q < 0·1 m³s^?1). Comparing W–Q relationships for concentrated flow channels revealed that the discharge exponent (b) varies from 0·3 for rills over 0·4 for gullies to 0·5 for rivers. This shift in b may be the result of: (i) differences in flow shear stress distribution over the wetted perimeter between rills, gullies and rivers, (ii) a decrease in probability of a channel formed in soil material with uniform erosion resistance from rills over gullies to rivers and (iii) a decrease in average surface slope from rills over gullies to rivers. The proposed W–Q equation for ephemeral gullies is valid for (sealed) cropland with no significant change in erosion resistance with depth. Two examples illustrate limitations of the W–Q approach. In a first example, vertical erosion is hindered by a frozen subsoil. The second example relates to a typical summer situation where the soil moisture profile of an agricultural field makes the top 0·02 m five times more erodible than the underlying soil material. For both cases observed W values are larger than those predicted by the established channel width equation for concentrated flow on cropland. For the frozen soils the equation W = 3·17 Q^0·368 (R² = 0·78; n = 617) was established, but for the summer soils no equation could be established. Copyright © 2002 John Wiley & Sons, Ltd.     

Measuring streambank erosion due to ground water seepage: correlation to bank pore water pressure,precipitation and stream stage

Limited information exists on one of the mechanisms governing sediment input to streams: streambank erosion by ground water seepage. The objective of this research was to demonstrate the importance of streambank composition and stratigraphy in controlling seepage flow and to quantify correlation of seepage flow/erosion with precipitation, stream stage and soil pore water pressure. The streambank site was located in Northern Mississippi in the Goodwin Creek watershed. Soil samples from layers on the streambank face suggested less than an order of magnitude difference in vertical hydraulic conductivity (K_s) with depth, but differences between lateral K_s of a concretion layer and the vertical K_s of the underlying layers contributed to the propensity for lateral flow. Goodwin Creek seeps were not similar to other seeps reported in the literature, in that eroded sediment originated from layers underneath the primary seepage layer. Subsurface flow and sediment load, quantified using 50 cm wide collection pans, were dependent on the type of seep: intermittent low‐flow (LF) seeps (flow rates typically less than 0·05 L min^?1), persistent high‐flow (HF) seeps (average flow rate of 0·39 L min^?1) and buried seeps, which eroded unconsolidated bank material from previous bank failures. The timing of LF seeps correlated to river stage and precipitation. The HF seeps at Goodwin Creek began after rainfall events resulted in the adjacent streambank reaching near saturation (i.e. soil pore water pressures greater than ?5 kPa). Seep discharge from HF seeps reached a maximum of 1·0 L min^?1 and sediment concentrations commonly approached 100 g L^?1. Buried seeps were intermittent but exhibited the most significant erosion rates (738 g min^?1) and sediment concentrations (989 g L^?1). In cases where perched water table conditions exist and persistent HF seeps occur, seepage erosion and bank collapse of streambank sediment may be significant. Copyright © 2007 John Wiley & Sons, Ltd.     

Hillslope–channel sediment transfer in a slope failure event: Wet Swine Gill,Lake District,northern England

This paper describes and analyses a hillslope–channel slope failure event that occurred at Wet Swine Gill, Lake District, northern England. This comprised a hillslope slide (180 m³, c. 203 ± 36 t), which coupled with the adjacent stream, resulting in a channelized debris flow and fluvial flood. The timing of the event is constrained between January and March 2002. The hillslope failure occurred in response to a rainfall/snowmelt trigger, on ground recently disturbed by a heather moorland fire and modified by artificial drainage. Slide and flow dynamics are estimated using reconstructed velocity and discharge values along the sediment transfer path. There is a rapid downstream reduction in both maximum velocity, from 9·8 to 1·3 m s^?1; and maximum discharge, ranging from 33·5 to 2·4 m³ s^?1. A volumetric sediment budget quantified a high degree of coupling between the hillslope and immediate channel (～92%: 167 m³), but virtually all of the sediment was retained in the first‐order tributary channel. Approximately 44% (81 m³) of the slide volume was retained in the run‐up deposit, and termination of the debris flow prior to the main river meant that the remainder did not discharge into the fluvial system downstream. These results suggest poor transmission of sediment to the main river at the time of the event, but importantly an increase in available material for post‐event sediment transfer processes within the small upland tributary. Copyright © 2007 John Wiley & Sons, Ltd.     

Zur ökonomischen Bedeutung der biologischen Selbstreinigung

In twelve flowing water (Q 1.04… 30.4 m³/s, 0.5… 1.2 m/s) the self-purification efficiency in 110 river sections (L 1.3… 26.4 km) is determined as the load difference in kg · d^?1 COD-Mn as well as in g · m^?3 referred to the daily passage. In the economical comparison, the self-purification efficiency is valued as substitution for wastewater treatment plants of the same capacity. At a mean specific capacity of 8.6 g · m^?3, the self-purification efficiency of the investigated waters is equivalent to economical values of 124 · 10³… 534 · 10³ M km^?1 investment costs, 11 · 10³… 80 · 10³ M · a^?1km^?1 operating costs and 5… 81 MWh · a^?1 km^?1 expenditure of energy. The specific capacity in g · m^?3 COD-Mn shows an exponential regression to the degree of saprobity (L = 0.015 · exp (1.7358 · S)). From this empirical model the limits of the self-purification capacity of aerobic waters by oxygen input can be detected: in respective examples more than 50% of the required oxygen input are due to weirs.     

Effects of sediment load on hydraulics of overland flow on steep slopes

Eroded sediment may have significant effects on the hydraulics of overland flow, but few studies have been performed to quantify these effects on steep slopes. This study investigated the potential effects of sediment load on Reynolds number, Froude number, flow depth, mean velocity, Darcy–Weisbach friction coefficient, shear stress, stream power, and unit stream power of overland flow in a sand‐glued hydraulic flume under a wide range of hydraulic conditions and sediment loads. Slope gradients were varied from 8·7 to 34·2%, unit flow rates from 0·66 to 5·26×10^?3 m² s^?1, and sediment loads from 0 to 6·95 kg m^?1 s^?1. Both Reynolds number (Re) and Froude number (Fr) decreased as sediment load increased, implying a decrease in flow turbulence. This inverse relationship should be considered in modeling soil erosion processes. Flow depth increased as sediment load increased with a mean value of 1·227 mm, caused by an increase in volume of sediment‐laden flow (contribution 62·4%) and a decrease in mean flow velocity (contribution 37·6%). The mean flow velocity decreased by up to 0·071 m s^?1 as sediment load increased. The Darcy–Weisbach friction coefficient (f) increased with sediment load, showing that the total energy consumption increased with sediment load. The effects of sediment load on f depended on flow discharge: as flow discharge increased, the influence of sediment load on f decreased due to increased flow depth and reduced relative roughness. Flow shear stress and stream power increased with sediment load, on average, by 80·5% and 60·2%, respectively; however, unit stream power decreased by an average of 11·1% as sediment load increased. Further studies are needed to extend and apply the insights obtained under these controlled conditions to real‐world overland flow conditions. Copyright © 2010 John Wiley & Sons, Ltd.     

Evaluating nitrate uptake in a Rocky Mountain stream using labelled 15N and ambient nitrate chemistry

Background aqueous chemistry and ¹⁵N_nitrate tracer injection methods were used to calculate in‐stream nitrate uptake metrics at Red Canyon Creek, a third‐order stream in the Rocky Mountains in the state of Wyoming, United States. ‘Net’ nitrate uptake lengths, which reflect both nitrate uptake and regeneration, and ‘gross’ nitrate uptake lengths, which exclude re‐mineralization, were quantified separately from background nitrate chemistry and ¹⁵N labelling tracer data, respectively. Gross nitrate uptake lengths, from tracer injections of ¹⁵N labelled nitrate, ranged from 502 to 3140 m. Net nitrate uptake lengths, from background nitrate chemistry downstream of a point source, ranged from 1170 to 4330 m. Diurnal changes in uptake lengths suggest the importance of nitrate utilization by autotrophs in the stream and benthic zone. The differences between net and gross nitrate uptake lengths along lower reaches of Red Canyon Creek allowed us to estimate the nitrate regeneration rate, which was 0·056–0·080 µmol m^?2 s^?1 during the day and 0·0062–0·0083 µmol m^?2 s^?1 at night. Spatial patterns of streambed pore water chemistry indicate those areas of the hyporheic zone where denitrification was likely occurring. Permanent log dams generated stronger redox gradients in the hyporheic zone than areas with transient beaver dams. By combining isotopically labelled nitrate additions, estimates of uptake from background aqueous nitrate chemistry and characterization of redox conditions in the hyporheic zone, we were able to determine the nitrate regeneration rate and the redox processes responsible for nitrogen cycling in the hyporheic zone. Copyright © 2010 John Wiley & Sons, Ltd.     

The nature and transport of the fine‐grained component of Swift Creek Landslide,Northwest Washington

Extreme sedimentation in Swift Creek, located in the Cascades foothills in NW Washington (48°55′N, 122°16′W), results from erosion of the oversteepened, unvegetated toe of a large (55 hectares) active landslide. Deposition of landslide‐derived sediment has necessitated costly mitigation projects in the channel including annual dredging and temporary sediment traps in an attempt to reduce the risk of flooding and damage to man‐made structures downstream. This study attempts to understand the process of sediment production along with the corresponding erosion rates of the sediment source to help with the development of mitigation plans and construction of optimal sediment reservoirs. The bedload and suspended sediment in the creek are a direct result of the weathering process of the serpentinitic bedrock underlying the landslide. The serpentinite does not weather to smectite clay, as previously thought. Instead, it weathers to asbestiform chrysotile with minor amounts of chlorite, illite and hydrotalcite, all of which occur in clay seeps on the unvegetated surface of the landslide. The chrysotile fibers average 2 µm in length and make up at least 50%, by volume, of the suspended load transported in Swift Creek. This study does not address the environmental or health implications of the asbestiform chrysotile transport or deposition. During the sampled time between February 2005 and February 2006, 127 discrete suspended sediment samples were collected and discharge was measured 66 times. The suspended sediment concentrations ranged from 0·02 g L^?1 to 41·6 g L^?1 and the discharge ranged from 0·0 m³ s^?1 to 0·5 m³ s^?1. A nonlinear functional model estimated the total suspended sediment flux from detailed precipitation records and discrete suspended sediment concentration and discharge measurements to be 910 t km^?2 yr^?1. When the suspended sediment flux is coupled with estimates of downstream deposition of coarse sediment, the estimated erosion rate for the entire Swift Creek landslide is 158 mm yr^?1. The majority of the material entering Swift Creek is presumed to originate on the unvegetated toe of the landslide, for which the erosion rate is thus approximately 1 m yr^?1. Copyright © 2010 John Wiley & Sons, Ltd.     

Suspended sediment dynamics in a steep,glacier‐fed mountain stream,Place Creek,Canada

This study examined suspended sediment concentration (SSC) during the ablation seasons of 2000 and 2001 in Place Creek, Canada, a steep, glacier‐fed mountain stream. Comparison of stream flow in Place Creek with that in an adjacent, almost unglacierized catchment provided a rational basis for separating the ablation seasons into nival, nival–glacial, glacial and autumn recession subseasons. Distinct groupings of points in plots of electrical conductivity against discharge supported the validity of the subseasonal divisions in terms of varying hydrological conditions. Relationships between SSC and discharge (Q) varied between the two study seasons, and between subseasons. Hysteresis in the SSC–Q relationship was evident at both event and weekly time‐scales. Some suspended sediment released from pro‐glacial Place Lake (the source of Place Creek) appeared to be lost to channel storage at low flows, especially early in the ablation season, with re‐entrainment at higher flows. Multiple regression models were derived for the subseasons using predictor variables including Q, Q², the change in Q over the previous 3 h, cumulative discharge over the ablation season, total precipitation over the previous 24 h and SSC measured at 1500 hours as an index value for each day. The models produced adjusted R² values ranging from 0·71 to 0·91, and provided tentative insights into the differences in SSC dynamics amongst subseasons. Introduction of the index value of SSC significantly improved the model fit during the nival–glacial and glacial subseasons for both years, as it adjusts the model to the current condition of sediment supply. Copyright © 2003 John Wiley & Sons, Ltd.     

Step–pool evolution in the Rio Cordon,northeastern Italy

The principle that formative events, punctuated by periods of evolution, recovery or temporary periods of steady‐state conditions, control the development of the step–pool morphology, has been applied to the evolution of the Rio Cordon stream bed. The Rio Cordon is a small catchment (5 km²) within the Dolomites wherein hydraulic parameters of floods and the coarse bedload are recorded. Detailed field surveys of the step–pool structures carried out before and after the September 1994 and October 1998 floods have served to illustrate the control on step–pool changes by these floods. Floods were grouped into two categories. The first includes ‘ordinary’ events which are characterized by peak discharges with a return time of one to five years (1·8–5·15 m³ s^?1) and by an hourly bedload rate not exceeding 20 m³ h^?1. The second refers to ‘exceptional’ events with a return time of 30–50 years. A flood of this latter type occurred on 14 September 1994, with a peak discharge of 10·4 m³ s^?1 and average hourly bedload rate of 324 m³ h^?1. Step–pool features were characterized primarily by a steepness parameter c = (H/L_s)/S. The evolution of the steepness parameter was measured in the field from 1992 to 1998. The results indicate that maximum resistance conditions are gradually reached at the end of a series of ordinary flood events. During this period, bed armouring dominate the sediment transport response. However, following an extraordinary flood and unlimited sediment supply conditions, the steepness factor can suddenly decrease as a result of sediment trapped in the pools and a lengthening of step spacing. The analogy of step spacing with antidune wavelength and the main destruction and transformation mechanism of the steps are also discussed. Copyright © 2001 John Wiley & Sons, Ltd.     

The effect of transient storage on nitrate uptake lengths in streams: an inter‐site comparison

Surface water–groundwater interaction in the hyporheic zone may enhance biogeochemical cycling in streams, and it has been hypothesized that streams exchanging more water with the hyporheic zone should have more rapid nitrate utilization. We used simultaneous conservative solute and nitrate addition tracer tests to measure transient storage (which includes hyporheic exchange and in‐stream storage) and the rate of nitrate uptake along three reaches within the Red Canyon Creek watershed, Wyoming. We calibrated a one‐dimensional transport model, incorporating transient storage (OTIS‐P), to the conservative solute breakthrough curves and used the results to determine the degree of transient storage in each reach. The nitrate uptake length was quantified from the exponential decrease in nitrate concentration with distance during the tracer tests. Nitrate uptake along the most downstream reach of Red Canyon Creek was rapid (turnover time K^?1_c = 32 min), compared with nitrate uptake reported in other studies (K^?1_c = 12 to 551 min), but other sites within the watershed showed little nitrate retention or loss. The uptake length S_w‐NO^?₃ for the most downstream reach was 500 m and the mass transfer coefficient V_f‐NO^?₃ was 6·3 m min^?1. Results from 15 other nitrate‐addition tracer tests were used to create a regression model relating transient storage and measures of stream flow to nitrate uptake length. The model, which includes specific discharge and transient storage area, explains almost half the variability in nitrate uptake length (adjusted R² = 0·44) and is most effective for comparing sites with very different stream characteristics. Although large differences in specific discharge and storage zone area explain inter‐site differences in nitrate uptake, other unmeasured variables, such as available organic carbon and microbial community composition, are likely important for predicting differences in nitrate uptake between sites with similar specific discharge rates and storage zone areas, such as when making intra‐site comparisons. Copyright © 2007 John Wiley & Sons, Ltd.     

The influence of flow discharge variations on the morphodynamics of a diffluence–confluence unit on a large river

Bifurcations are key geomorphological nodes in anabranching and braided fluvial channels, controlling local bed morphology, the routing of sediment and water, and ultimately defining the stability of their associated diffluence–confluence unit. Recently, numerical modelling of bifurcations has focused on the relationship between flow conditions and the partitioning of sediment between the bifurcate channels. Herein, we report on field observations spanning September 2013 to July 2014 of the three‐dimensional flow structure, bed morphological change and partitioning of both flow discharge and suspended sediment through a large diffluence–confluence unit on the Mekong River, Cambodia, across a range of flow stages (from 13 500 to 27 000 m³ s^?1). Analysis of discharge and sediment load throughout the diffluence–confluence unit reveals that during the highest flows (Q = 27 000 m³ s^?1), the downstream island complex is a net sink of sediment (losing 2600 ± 2000 kg s^?1 between the diffluence and confluence), whereas during the rising limb (Q = 19 500 m³ s^?1) and falling limb flows (Q = 13 500 m³ s^?1) the sediment balance is in quasi‐equilibrium. We show that the discharge asymmetry of the bifurcation varies with discharge and highlight that the influence of upstream curvature‐induced water surface slope and bed morphological change may be first‐order controls on bifurcation configuration. Comparison of our field data to existing bifurcation stability diagrams reveals that during lower (rising and falling limb) flow the bifurcation may be classified as unstable, yet transitions to a stable condition at high flows. However, over the long term (1959–2013) aerial imagery reveals the diffluence–confluence unit to be fairly stable. We propose, therefore, that the long‐term stability of the bifurcation, as well as the larger channel planform and morphology of the diffluence–confluence unit, may be controlled by the dominant sediment transport regime of the system. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

In situ quantification of spatial and temporal variability of hyporheic exchange in static and mobile gravel‐bed rivers

Seepage meters modified for use in flowing water were used to directly measure rates of exchange between surface and subsurface water in a gravel‐ and cobble bed river in western Pennsylvania, USA (Allegheny River, Q_mean = 190 m³/s) and a sand‐ and gravel‐bed river in Colorado, USA (South Platte River, Q_mean = 9·7 m³/s). Study reaches at the Allegheny River were located downstream from a dam. The bed was stable with moss, algae, and river grass present in many locations. Median seepage was + 0·28 m/d and seepage was highly variable among measurement locations. Upward and downward seepage greatly exceeded the median seepage rate, ranging from + 2·26 (upward) to ? 3·76 (downward) m/d. At the South Platte River site, substantial local‐scale bed topography as well as mobile bedforms resulted in spatial and temporal variability in seepage greatly in exceedence of the median groundwater discharge rate of 0·24 m/d. Both upward and downward seepage were recorded along every transect across the river with rates ranging from + 2·37 to ? 3·40 m/d. Despite a stable bed, which commonly facilitates clogging by fine‐grained or organic sediments, seepage rates at the Allegheny River were not reduced relative to those at the South Platte River. Seepage rate and direction depended primarily on measurement position relative to local‐ and meso‐scale bed topography at both rivers. Hydraulic gradients were small at nearly all seepage‐measurement locations and commonly were not a good indicator of seepage rate or direction. Therefore, measuring hydraulic gradient and hydraulic conductivity at in‐stream piezometers may be misleading if used to determine seepage flux across the sediment‐water interface. Such a method assumes that flow between the well screen and sediment‐water interface is vertical, which appears to be a poor assumption in coarse‐grained hyporheic settings. Copyright © 2011 John Wiley & Sons, Ltd.     

The effect of El Niño Southern Oscillation cycles on the decadal scale suspended sediment behavior of a coastal dry‐summer subtropical catchment

Rivers display temporal dependence in suspended sediment–water discharge relationships. Although most work has focused on multi‐decadal trends, river sediment behavior often displays sub‐decadal scale fluctuations that have received little attention. The objectives of this study were to identify inter‐annual to decadal scale fluctuations in the suspended sediment–discharge relationship of a dry‐summer subtropical river, infer the mechanisms behind these fluctuations, and examine the role of El Niño Southern Oscillation climate cycles. The Salinas River (California) is a moderate sized (11 000 km²), coastal dry‐summer subtropical catchment with a mean discharge (Q_mean) of 11.6 m³ s^?1. This watershed is located at the northern most extent of the Pacific coastal North America region that experiences increased storm frequency during El Niño years. Event to inter‐annual scale suspended sediment behavior in this system was known to be influenced by antecedent hydrologic conditions, whereby previous hydrologic activity regulates the suspended sediment concentration–water discharge relationship. Fine and sand suspended sediment in the lower Salinas River exhibited persistent, decadal scale periods of positive and negative discharge corrected concentrations. The decadal scale variability in suspended sediment behavior was influenced by inter‐annual to decadal scale fluctuations in hydrologic characteristics, including: elapsed time since small (~0.1 × Q_mean), and moderate (~10 × Q_mean) threshold discharge values, the number of preceding days that low/no flow occurred, and annual water yield. El Niño climatic activity was found to have little effect on decadal‐scale fluctuations in the fine suspended sediment–discharge relationship due to low or no effect on the frequency of moderate to low discharge magnitudes, annual precipitation, and water yield. However, sand concentrations generally increased in El Niño years due to the increased frequency of moderate to high magnitude discharge events, which generally increase sand supply. Copyright © 2014 John Wiley & Sons, Ltd.     

SUR LES PROJECTS FUTURS DE L'AISH / ON THE FUTURE PLANS OF IAHS

Abstract

The baseflow characteristics of some of the numerous small basins in southeastern Nigeria have been analysed to estimate the developable groundwater in the basins. It is shown that from 5.62 × 10⁴ to 1.59 × 10⁶ m³ of groundwater can be developed per square kilometre of basin per annum. The relationship between the baseflow characteristics and other attributes of the basins, such as geology and stream density, were studied statistically, leading to the development of empirical equations for predicting the hydrological features of the several ungauged streams in the region. It is shown, for example, that the basin geology (represented as the percentage of sands), the drainage density, the basin area, the baseflow depletion rate and the total groundwater stored in the basin, Q_tp, are related by the equation:

Q_tp = ?1.85 × 10⁹?7.96 × 10⁸ dd+4.18 × 10⁷ gf?2.01 × 10⁶ df+6.25 × 10⁵ wa

where dd is drainage density; gf geological factor; df depletion factor; and wa basin area.     

A rare landform: Yerköprü travertine bridges in the Taurids Karst Range,Turkey

Two examples of travertine bridges are observed at 8 to 15 m above stream level in the Lower Zamanti Basin, Eastern Taurids, Turkey. Yerköprü‐1 and Yerköprü‐2 bridges are currently being deposited from cool karstic groundwaters with log P_CO2 > 10^?2 atm. The surface area and the total volume of travertine in Yerköprü‐1 bridge are 4350 m² and 40 000 m³, whereas the values for Yerköprü‐2 are 2250 m² and 20 000 m³, respectively. The interplay of hydrogeological structure, local topography, calcite‐saturated hanging springs, algal activity and rapid downcutting in the streambed appear to have led to the formation of travertine bridges. Aeration through cascades and algal uptake causes efficient carbon dioxide evasion that enhances travertine formation. Algal curtains aid lateral development of travertine rims across the stream. Model calculations based on a hypothetical deposit in the form of a half‐pyramid implied that lateral development should have occurred from both banks of the stream in the Yerköprü‐1 bridge, whereas one‐sided growth has been sufficient for Yerköprü‐2. The height difference between travertine springs and the main stream appears to be a result of Pleistocene glaciation during which karstic base‐level lowering was either stopped or slowed down while downcutting in the main stream continued. Copyright © 2002 John Wiley & Sons, Ltd.     

Evaluating sulfur dynamics during storm events for three watersheds in the northeastern USA: a combined hydrological,chemical and isotopic approach

Concerns related to climate change have resulted in an increasing interest in the importance of hydrological events such as droughts in affecting biogeochemical responses of watersheds. The effects of an unusually dry summer in 2002 had a marked impact on the biogeochemistry of three watersheds in the north‐eastern USA. Chemical, isotopic and hydrological responses with particular emphasis on S dynamics were evaluated for Archer Creek (New York), Sleepers River (Vermont) and Cone Pond (New Hampshire) watersheds. From 1 August to 14 September 2002, all three watersheds had very low precipitation (48 to 69 mm) resulting in either very low or no discharge (mean 0·015, 0·15 and 0·000 mm day^?1 for Archer Creek, Sleepers River and Cone Pond, respectively). From 15 September to 31 October 2002, there was a substantial increase in precipitation totals (212, 246 and 198 mm, respectively) with increased discharge. Archer Creek was characterized by a large range of SO₄^2? concentrations (152 to 389 µeq L^?1, mean = 273 µeq L^?1) and also exhibited the greatest range in δ³⁴S values of SO₄^2? (?1·4 to 8·8 ‰ ). Sleepers River's SO₄^2? concentrations ranged from 136 to 243 µeq L^?1 (mean = 167 µeq L^?1) and δ³⁴S values of SO₄^2? ranged from 4·0 to 9·0 ‰ . Cone Pond's SO₄^2? concentrations (126–187 µeq L^?1, mean = 154 µeq L^?1) and δ³⁴S values (2·4 to 4·3 ‰ ) had the smallest ranges of the three watersheds. The range and mean of δ¹⁸O‐SO₄^2? values for Archer Creek and Cone Pond were similar (3·0 to 8·9 ‰ , mean = 4·5 ‰ ; 3·9 to 6·3 ‰ , mean = 4·9 ‰ ; respectively) while δ¹⁸O‐SO₄^2? values for Sleepers River covered a larger range with a lower mean (1·2 to 10·0 ‰ , mean = 2·5). The difference in Sleepers River chemical and isotopic responses was attributed to weathering reactions contributing SO₄^2?. For Archer Creek wetland areas containing previously reduced S compounds that were reoxidized to SO₄^2? probably provided a substantial source of S. Cone Pond had limited internal S sources and less chemical or isotopic response to storms. Differences among the three watersheds in S biogeochemical responses during these storm events were attributed to differences in S mineral weathering contributions, hydrological pathways and landscape features. Further evaluations of differences and similarities in biogeochemical and hydrological responses among watersheds are needed to predict the impacts of climate change. Copyright © 2008 John Wiley & Sons, Ltd.     

Controls on effective settling velocities of mud flocs in the Changjiang Estuary,China

Theoretical and experimental studies were undertaken to gain insight into physical parameters controlling the flocculation and settling properties of mud flocs in the Changjiang Estuary, China. The Rouse equation is applied to vertical profiles of suspended sediment concentration to determine the bulk mean settling velocity (w_s) of sediment suspended in the Changjiang Estuary. Both in situ point‐sampled and acoustically measured profiles of suspended mud concentrations were fit selectively. The calculated settling velocities w_s mainly ranged from 0·4 to 4·1 mm s^?1 for the point‐sampled data set, and from 1·0 to 3·0 mm s^?1 for the acoustically measured data set. Furthermore, the settling velocities of mud flocs increased with mean concentration (C?) of mud flocs in suspension and were proportional to increasing bottom shear stress (τ_b) of tidal flow. The best equation for the field settling velocity of mud flocs in the Changjiang Estuary can be expressed by the power law: w_s = mC?ⁿ (m, 1·14–2·37; n, 0·84–1·03). It is suggested that C? and τ_b were the dominant physical parameters controlling the flocculation and w_s of mud flocs in suspension. Copyright © 2004 John Wiley & Sons, Ltd.     

A comparison of fibre‐optic distributed temperature sensing to traditional methods of evaluating groundwater inflow to streams

There are several methods for determining the spatial distribution and magnitude of groundwater inputs to streams. We compared the results of conventional methods [dye dilution gauging, acoustic Doppler velocimeter (ADV) differential gauging, and geochemical end‐member mixing] to distributed temperature sensing (DTS) using a fibre‐optic cable installed along 900 m of Ninemile Creek in Syracuse, New York, USA, during low‐flow conditions (discharge of 1·4 m³ s^?1). With the exception of differential gauging, all methods identified a focused, contaminated groundwater inflow and produced similar groundwater discharge estimates for that point, with a mean of 66·8 l s^?1 between all methods although the precision of these estimates varied. ADV discharge measurement accuracy was reduced by non‐ideal conditions and failed to identify, much less quantify, the modest groundwater input, which was only 5% of total stream flow. These results indicate ambient tracers, such as heat and geochemical mixing, can yield spatially and quantitatively refined estimates of relatively modest groundwater inflow even in large rivers. DTS heat tracing, in particular, provided the finest spatial characterization of groundwater inflow, and may be more universally applicable than geochemical methods, for which a distinct and consistent groundwater end member may be more difficult to identify. Copyright © 2011 John Wiley & Sons, Ltd.