Simulations of water movement and solute transport through different soil texture configurations under negative‐pressure irrigation

This study examined the effects of different soil texture configurations on water movement and solute transport to provide a reliable scientific basis for the application of negative‐pressure irrigation (NPI) technology. HYDRUS‐2D was used to analyse water movement and solute transport under NPI. The main results are as follows: (a) HYDRUS‐2D can be used to simulate water movement and solute transport under NPI, as there was good agreement between the simulated and measured values for water contents, NaCl concentrations, cumulative water infiltration, and wetting distances in the horizontal and vertical directions; the Nash–Sutcliffe efficiency coefficients were in the range of 0.94–0.97. (b) Layered soils have obvious effects on water movement under NPI. With the emitter position in the loam layer, when a coarse texture of loamy sand was present below the loam layer (namely, L‐LS), irrigation water accumulated in the topsoil, and this led to an increase in evaporation compared with the homogeneous loam profile. However, fine texture silty loam or silty clay loam layers beneath the loam layer (namely, L‐SiL or L‐SiCL, respectively) was more conducive to water infiltration into the lower layer, and this increased the amount of water infiltration and simultaneously reduced the surface evaporation effectively. (c) Layered soils have obvious effects on solute transport under NPI, and salt accumulation will readily occur in the clay‐rich soil layer at the interface. The maximum soil salt accumulation of L‐LS occurred above the soil interface between the two soil layers with a value of 21.80 g/kg; however, for L‐SiCL and L‐SiL, the maximum salt accumulation occurred below the soil interface between the two soil layers, with values of 23.80 g/kg and 20.08 g/kg, respectively. (d) Interlayered soils showed remarkable changes in the water infiltration characteristics and salt‐leaching intensities under NPI, and the properties for the soil profile with a silty loam interlayer were better than those for the soil profile with a silty clay loam interlayer. The soil profile with a loamy sand interlayer had the lowest amount of water infiltration, which resulted in reductions of the salt‐leaching intensities. Thus, NPI is clearly not suitable for loamy sand soil. Overall, the results demonstrated that soil texture configurations affected water movement and solute transport under NPI. Therefore, careful consideration should be given to the use of NPI to achieve target soil water and solution conditions and reduce water loss.     

Temporal stability of soil water content as affected by climate and soil hydraulic properties: a simulation study

Temporal stability of soil water content (TS SWC) is an often‐observed phenomenon, which characterization finds multiple applications. Climate and variability in soil properties are usually mentioned as factors of TS SWC, but their effects are far from clear. The objective of this work was to use SWC modeling to evaluate the effects of climate and soil hydraulic properties on the TS of soil water at different measurement schedules. We selected four representative climates found in USA and simulated the multiyear SWC dynamics for sandy loam, loam, and silty clay loam soils, all having the lognormal spatial distribution of the saturated hydraulic conductivity. The CLIMGEN and the HYDRUS6 codes were used to generate weather patterns and to simulate SWC, respectively. Four different methods were applied to select the representative location (RL). The low probability of having the same variability of mean relative differences of soil water under different climates was found in most of the cases. The probability that the variance of mean relative differences depended on sampling frequency was generally higher than 91% for the three soils. The interannual difference in mean relative differences variation from short and intensive summer campaigns was highly probable for all climates and soils. The RLs changed as climate and measurement scheduling changed, and they were less pronounced for coarse‐textured soils. The RL selection methods based solely on bias provided more consistency as compared with other methods. The TS appears to be the result of the interplay between climate, soil properties, and survey protocols. One implication of this factor interaction effect on TS SWC is that a simulation study can be useful to decide on the feasibility of including a search for TS‐based RLs for a specific site. Copyright © 2013 John Wiley & Sons, Ltd.     

Effects of water quality on infiltration,runoff and interrill erosion processes during simulated rainfall

This paper discusses the effects of water quality on the hydrological and erosion response of non‐saline, non‐sodic soils during simulated rain experiments. It is well known that rain water quality affects the behaviour of saline soils. In particular, rain simulation experiments cannot be run using tap water if realistic values of infiltration rates and soil erosion are to be found. This paper reports on similar effects for non‐saline, non‐sodic soils. Two soils – a well‐aggregated clay‐rich soil developed on marine silty clay deposits and a soil developed on silt loam – were selected and subjected to a series of simulated rainstorms using demineralized water and tap water. The experiments were conducted in two different laboratories in order to obtain results independent of the tap water quality or the rainfall simulator characteristics. The results indicate that time‐to‐ponding is largely delayed by solute‐rich water (tap water). When tap water is used, infiltration rates are significantly overestimated, i.e. by more than 100 per cent. Interrill erosion rates increase by a factor of 2·5–3 when demineralized water is used. The silty clay soil was more affected by the water quality than the silt loam soil, with respect to infiltration and runoff production. Regarding interrill erosion rates, the two tested soils were similarly affected by the water quality. Therefore, it can be concluded that rainfall simulation experiments with non‐dispersive soils (e.g. non‐saline, non‐sodic) must also be conducted using water with very low electrical conductivity (i.e. less than 30–50 µS cm⁻¹), close to that of distilled water. The use of tap water certainly hampers comparisons and the relative ranking of the hydrological and erosion response of different soils, while parameter values, such as final infiltration rate or time‐to‐ponding, cannot be extrapolated and extended to natural situations. Therefore, the majority of hydrological and erosion models and parameter values measured during rainfall simulations in the past should be used with caution for all types of soils. Copyright © 2001 John Wiley & Sons, Ltd.     

The Effects of Hydrophilic Polymer and Soil Salinity on Corn Growth in Sandy and Loamy Soils

The interaction effects of different applied ratios of a hydrophilic polymer (Superab A200) (0, 0.2, 0.6% w/w) under various soil salinity levels (initial salinity, 4 and 8 ms/cm) were evaluated on available water content (AWC), biomass, and water use efficiency for corn grown in loamy sand and sandy clay loam soils. The results showed that the highest AWC was measured at the lowest soil salinity. The application of 0.6% w/w of the polymer at the lowest salinity level increased the AWC by 2.2 and 1.2 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. The analysis of variance of data showed that the effect of salinity was significant on biomass and water use efficiency of corn in the loamy sand and sandy clay loam soils. The highest amounts of these traits were measured in soils with the lowest salinity level. Application of polymer at the rate of 0.6% in the loamy sand soil and at the rate of 0.2% in the sandy clay loam soil resulted in the highest aerial and root biomass and water use efficiency for corn. At these polymer rates the amounts of water use efficiency for corn were 2.6 and 1.7 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. Thus, the use of hydrophilic polymer in soils especially in the sandy soils increases soil water holding capacity, yield, and water use efficiency of plant. On the other hand, decreases the negative effect of soil salinity on plant and helps for irrigation projects to succeed in arid and semi‐arid areas.     

Simulation of field‐scale water flow and bromide transport in a cracked clay soil

Single domain models may seriously underestimate leaching of nutrients and pesticides to groundwater in clay soils with shrinkage cracks. Various two‐domain models have been developed, either empirical or physically based, which take into account the effects of cracks on water flow and solute transport. This paper presents a model concept that uses the clay shrinkage characteristics to derive crack volume and crack depth under transient field conditions. The concept has been developed to simulate field average behaviour of a field with cracks, rather than flow and transport at a small plot. Water flow and solute transport are described with basic physics, which allow process and scenario analysis. The model concept is part of the more general agrohydrological model SWAP, and is applied to a field experiment on a cracked clay soil, at which water flow and bromide transport were measured during 572 days. A single domain model was not able to mimic the field‐average water flow and solute transport. Incorporation of the crack concept considerably improved the simulation of water content and bromide leaching to the groundwater. Still deviations existed between the measured and simulated bromide concentration profiles. The model did not reproduce the observed bromide retardation in the top layer and the high bromide dispersion resulting from water infiltration at various soil depths. A sensitivity analysis showed that the amounts of bromide leached were especially sensitive to the saturated hydraulic conductivity of the top layer, the solute transfer from the soil matrix to crack water flow and the mean residence time of rapid drainage. The shrinkage characteristic and the soil hydraulic properties of the clay matrix showed a low sensitivity. Copyright © 2000 John Wiley & Sons, Ltd.     

Sodicity effects on hydrological processes of sodic soil slopes under simulated rainfall

Soil salinization can occur in many regions of the world. Soil sodicity affects rainfall‐runoff relationships and related erosion processes considerably. We investigated sodicity effects on infiltration, runoff and erosion processes on sodic soil slopes for two soils from China under simulated rainfall. Five sodicity levels were established in a silt loam and a silty clay with clay contents of 8.5% and 46.0%, respectively. The soils, packed in 50 cm × 30 cm × 15 cm flumes at two slope gradients (22° and 35°), were exposed to 60 min of simulated rainfall (deionized water) at a constant intensity of 125 mm h^?1. Results showed that, for both soils, increasing soil sodicity had some significant effects on hydrological processes, reducing the infiltration coefficient (pr = ?0.69, P  < 0.01) and the quasi‐steady final infiltration rate (pr = ?0.80, P  < 0.01), and increasing the mean sediment loss (pr = 0.39, P  < 0.05); however, it did not significantly affect the cumulative rainfall to ponding (P  > 0.05). Moreover, increasing sodicity significantly increased the Reynolds number and the stream power (pr = 0.78 and 0.66, P  < 0.01, respectively) of the runoff, decreased Manning roughness and Darcy–Weisbach coefficient (pr = ?0.52 and ?0.52, P  < 0.05, respectively), but did not significantly affect the mean flow velocity, mean flow depth, Froude number and hydraulic shear stress. Stream power was shown to be the most sensitive hydraulic variable affecting sediment loss for both soils. Furthermore, as sodicity increased, the values of critical stream power decreased for both the silt loam (R ² = 0.29, P  < 0.05) and the silty clay (R ² = 0.49, P  < 0.05). The findings of this study were applied to a real situation and identified some negative effects that can occur with increasing sodicity levels. This emphasized the importance of addressing the influences of soil sodicity in particularly high risk situations and when predicting soil and water losses.     

Spatio-temporal evolution and time-stable characteristics of soil moisture within remote sensing footprints with varying soil, slope, and vegetation

Air-borne passive microwave remote sensors measure soil moisture at the footprint scale, a scale of several hundred square meters or kilometers that encompasses different characteristic combinations of soil, topography, vegetation, and climate. Studies of within-footprint variability of soil moisture are needed to determine the factors governing hydrologic processes and their relative importance, as well as to test the efficacy of remote sensors. Gridded ground-based impedance probe water content data and aircraft-mounted Electronically Scanned Thinned Array Radiometer (ESTAR) pixel-average soil moisture data were used to investigate the spatio-temporal evolution and time-stable characteristics of soil moisture in three selected (LW03, LW13, LW21) footprints from the Southern Great Plains 1997 (SGP97) Hydrology Experiment. Better time-stable features were observed within a footprint containing sandy loam soil than within two pixels containing silty loam soil. Additionally, flat topography with split wheat/grass land cover produced the largest spatio-temporal variability and the least time stability in soil moisture patterns. A comparison of ground-based and remote sensing data showed that ESTAR footprint-average soil moisture was well calibrated for the LW03 pixel with sandy loam soil, rolling topography, and pasture land cover, but improved calibration is warranted for the LW13 (silty loam soil, rolling topography, pasture land) and LW21 (silty loam soil, flat topography, split vegetation of wheat and grass land with tillage practice) pixels. Footprint-scale variability and associated nonlinear soil moisture dynamics may prove to be critical in the regional-scale hydroclimatic models.     

Research on Dynamic Parameters of Soil Site in the Tianjin Coastal Area

The Tianjin coastal area is a typical soft soil region,where the soil is a marine deposit of the late Quaternary.The soil dynamic parameters from seismic risk assessment reports are collected,and drilling of 15 holes was carried out to sample the soils and measure their dynamic characteristics.The data was divided into 7 types based on lithology,namely,muddy clay,muddy silty clay,silt,silty clay,clay,silty sand and fine sand.Statistics of the dynamic parameters of these soils are collected to obtain the mea...     

Design of Lysimeter Leak Detector Networks for Surface Impoundments and Landfills

Sampling of soil pore moisture in the vadose zone underneath land disposal facilities (landfills and surface impoundments) for hazardous waste has been suggested as an "early warning system" to detect leakage from these facilities. Some states require vadose zone moisture sampling at such sites. Given a leak of a particular size, mathematical models can estimate the necessary moisture sample volume collection times and lysimeter spacings to guarantee detection of the leak in a homogeneous medium. Examination of 47 hazardous waste sites existing in 1984 indicated the most were located in areas with water tables too shallow to permit vadose zone detection monitoring. Several of the 47 sites had soils that could be described as loamy sand, silt loam or silty clay. Using these three soils as examples, the process of lysimeter leak-detector network design has been illustrated. For a particular loamy sand with a saturates hydraulic conductivity of 10^-6 cm/ sec, the maximum ceramic lysimeter spacing is 15.5 feet at a depth of 30 feet to collec a moisture sample of 10 mL in one week from a 1 ft2 leak. For a silt loam, maximum lysimeter spacing would be 17 feet at depth of 15 feet. For silty clays, the maximum lysimeter spacing is 7 feet at a depth of 2 feet; maximum emplacement depth is about 9 feet. Calculations show that in some soils, suction lysimeters will not be able to collect usable moisture samples. Since soil properties vary widely and lysimeter spacing is strongly dependent on soil-moisture characteristics appropriate soil measurements and modeling must be performed at each disposal facility to estimate lysimete performance and to select locations for emplacement.     

Differences in preferential flow with antecedent moisture conditions and soil texture: Implications for subsurface P transport

Preferential flowpaths transport phosphorus (P) to agricultural tile drains. However, if and to what extent this may vary with soil texture, moisture conditions, and P placement is poorly understood. This study investigated (a) interactions between soil texture, antecedent moisture conditions, and the relative contributions of matrix and preferential flow and (b) associated P distributions through the soil profile when fertilizers were applied to the surface or subsurface. Brilliant blue dye was used to stain subsurface flowpaths in clay and silt loam plots during simulated rainfall events under wet and dry conditions. Fertilizer P was applied to the surface or via subsurface placement to plots of different soil texture and moisture condition. Photographs of dye stains were analysed to classify the flow patterns as matrix dominated or macropore dominated, and soils within plots were analysed for their water‐extractable P (WEP) content. Preferential flow occurred under all soil texture and moisture conditions. Dye penetrated deeper into clay soils via macropores and had lower interaction with the soil matrix, compared with silt loam soil. Moisture conditions influenced preferential flowpaths in clay, with dry clay having deeper infiltration (92 ± 7.6 cm) and less dye–matrix interaction than wet clay (77 ± 4.7 cm). Depth of staining did not differ between wet (56 ± 7.2 cm) and dry (50 ± 6.6 cm) silt loam, nor did dominant flowpaths. WEP distribution in the top 10 cm of the soil profile differed with fertilizer placement, but no differences in soil WEP were observed at depth. These results demonstrate that large rainfall events following drought conditions in clay soil may be prone to rapid P transport to tile drains due to increased preferential flow, whereas flow in silt loams is less affected by antecedent moisture. Subsurface placement of fertilizer may minimize the risk of subsurface P transport, particularily in clay.     

The use of small flumes for the determination of soil erodibility

The objective of this study was to examine the possibility of determining soil erodibility of loamy soils with small flumes. This was done by comparing the classification of soil erodibility obtained in the field with that obtained in the laboratory. Therefore twenty soils with a texture varying from silty loam to sandy loam were selected from the Leuven region. The erosion in the field was determined by measuring the volumetric evolution of the rill pattern. In the laboratory the soils were tested with a rainfall simulator and small flumes. The conclusion was that for loamy soils the flume experiments are a quick, simple, and reliable method for the determination of the relative soil erodibility.     

Hillslope scale surface runoff,sediment and nutrient losses associated with tramline wheelings

Research on arable sandy loam and silty clay loam soils on 4° slopes in England has shown that tramlines (i.e. the unseeded wheeling areas used to facilitate spraying operations in cereal crops) can represent the most important pathway for phosphorus and sediment loss from moderately sloping fields. Detailed monitoring over the October–March period in winters 2005–2006 and 2006–2007 included event‐based sampling of surface runoff, suspended and particulate sediment, and dissolved and particulate phosphorus from hillslope segments (each ～300–800 m²) established in a randomized block design with four replicates of each treatment at each of two sites on lighter and heavier soils. Experimental treatments assessed losses from the cropped area without tramlines, and from the uncropped tramline area, and were compared to losses from tramlines which had been disrupted once in the autumn with a shallow tine. On the lighter soil, the effects of removal or shallow incorporation of straw residues was also determined. Research on both sandy and silty clay loam soils across two winters showed that tramline wheelings represented the dominant pathway for surface runoff and transport of sediment, phosphorus and nitrogen from cereal crops on moderate slopes. Results indicated 5·5–15·8% of rainfall lost as runoff, and losses of 0·8–2·9 kg TP ha^?1 and 0·3–4·8 t ha^?1 sediment in tramline treatments, compared to only 0·2–1·7% rainfall lost as runoff, and losses of 0·0–0·2 kg TP ha^?1 and 0·003–0·3 t ha^?1 sediment from treatments without tramlines or those where tramlines had been disrupted. The novel shallow disruption of tramline wheelings using a tine once following the autumn spray operation consistently and dramatically reduced (p < 0·001) surface runoff and loads of sediment, total nitrogen and total phosphorus to levels similar to those measured in cropped areas between tramlines. Results suggest that options for managing tramline wheelings warrant further refinement and evaluation with a view to incorporating them into spatially‐targeted farm‐level management planning using national or catchment‐based agri‐environment policy instruments aimed at reducing diffuse pollution from land to surface water systems. Copyright © 2010 John Wiley & Sons, Ltd.     

Effects of Hydrogel Amendment to Different Soils on Plant Available Water and Survival of Trees under Drought Conditions

The effect of super absorbent polyacrylate (SAP) hydrogel amendment to different soil types on plant available water (PAW), evapotranspiration and survival of Eucalyptus grandis, Eucalyptus citriodora, Pinus caribaea, Araucaria cunninghamii, Melia volkensii, Grevillea robusta, Azadirachta indica, Maesopsis eminii and Terminalia superba was investigated. The seedlings were potted in 3 kg size polythene bags filled with sand, loam, silt loam, sandy loam and clay soils, amended at 0 (control), 0.2 and 0.4% w/w hydrogel. The tree seedlings were allowed to grow normally with routine uniform watering in a glass house set up for a period of eight weeks, after which they were subjected to drought conditions by not watering any further. The 0.4% hydrogel amendment significantly (p < 0.05) increased the PAW by a factor of about three in sand, two fold in silt loam and one fold in sandy loam, loam and clay soils compared to the control. Similarly, the addition of either 0.2 or 0.4% hydrogel to the five soil types resulted in prolonged tree survival compared to the controls. Araucaria cunninghammi survived longest at 153 days, while Maesopsis eminii survived least (95 days) in sand amended at 0.4% after subjection to desiccation. Evapotranspiration was reduced in eight of the nine tree species grown in sandy loam, loam, silt loam and clay soils amended at 0.4% hydrogel. It is probable that soil amendment with SAP decreased the hydraulic soil conductivity that might reduce plant transpiration and soil evaporation.     

Effects of length and application rate of rice straw mulch on surface runoff and soil loss under laboratory simulated rainfall

Forest land affected by deforestation yields high soil and water losses.Suitable management practices need to be found that can reduce these losses and achieve ecological and hydrological sustainability of the deforested areas.Mulch has been found to be effective in reducing soil losses;straw mulch is easy to apply,contributes soil organic matter,and is efficient since the day of application.However,the complex effects of rice straw mulch with different application rates and lengths on surface runoff and soil loss have not been clarified in depth.The current paper evaluates the efficiency of rice straw mulch in reducing the hydrological response of a silty clay loam soil under high intensity and low frequency rainfall events(tap water with total depth of 49 mm and intensity of 98 mm/h)simulated in the laboratory.Surface runoff and soil loss at three lengths of the straw(10,30,and 200 mm)and three application rates(1,2,and 3 Mg/ha)were measured in 50 cm(width)×100 cm(length)×10 cm(depth)plots with disturbed soil samples(aggregate soil size<4 mm)collected in a deforested area.Bare soil was used as control experiment.Runoff volume and erosion were significantly(at p<0.05)lower in mulched soils compared to control plots.These reductions were ascribed to the water absorption capacity of the rice straw and the protection cover of the mulch layer.The minimum runoff was observed for a mulch layer of3 Mg/ha of straw with a length of 200 mm.The lowest soil losses were found with straw length of10 mm.The models developed predict runoff and erosion based on simple linear functions of mulch application rate and length,and can be used for a suitable hydrological management of soil.It is concluded that,thanks to rice straw mulch used as an organic soil conditioner,soil erosion and surface runoff are significantly(at p<0.05)reduced,and the mulch protection contributes to reduce the risk of soil degradation.Further research is,however,needed to analyze the upscaling of the hydrological effects of mulching from the plot to the hillslope scale.     

Effects of incorporating two organic materials at varying levels on splash detachment of some soils from Borno state,Nigeria

Splash detachment by raindrops was measured using a factorial experiment involving three soils (sandy loam, clay loam and clay) and two organic materials (cow dung and groundnut haulms) applied at five levels (0, 2, 4, 6 and 8 per cent by mass). A simulated rainfall intensity of 145 mm h^?1 for 10 min duration was used for the tests. Detachment was described in terms of the direct effects and the first and second order interactions of the variables mentioned above. Results indicated that mean splash detachment was reduced significantly (P < 0·01) from 1·97 kg m^?2 in the sandy loam to 0·67 kgm^?2 in the clay soil. For each soil type, detachment was reduced significantly (P < 0.01) with increasing levels of added organic matter. Groundnut haulms produced lower values of detachment than cow dung. There were also significant interaction effects between the study variables. These interactions were used to describe the effect of added organic materials on splash detachment. For each soil type and organic material, negative exponential relationships were established to relate splash detachment to levels of added organic matter.     

Nitrate leaching through the unsaturated zone following pig slurry applications

As the increase of nitrate concentration in groundwater has often been ascribed to an inappropriate use of liquid manure, the main purpose of this study was to better understand the factors controlling nitrate dynamics in the unsaturated zone of soils subjected to characteristic agronomic practices, and to contribute to improving Action Programmes, with reference to EU Directive 91/676, for nitrate vulnerable zones (NVZ).Water infiltration and nitrate leaching have been studied in experimental fields located inside nitrate vulnerable zones of the Emilia-Romagna region (Northern Italy), characterized by different pedological and hydrogeological properties and equipped with meteorological station, tensiometers, ceramic-cup samplers and piezometers. This article describes the results obtained from one of these sites, monitored over a 6-year period, which was cereal cropped and treated with pig slurry. MACRO and SOILN field-scale models have been used in order to verify the reliability of simulated water flow and nitrogen transport.The results demonstrate how nitrogen inputs from slurry, substantially higher than crop uptake, cause nitrate accumulation in the surface layer of the soil especially in warm periods (concentrations of up to 300 mg NO₃–N l⁻¹ were found in soil water). Even if the soil texture was fine, the shrinking–swelling properties of clay minerals determined fast drainage conditions (related to macroporosity), so that during the early rainy periods nitrates leached through the first meters of the unsaturated zone, at least down to 4 m. This shows that nitrate accumulation should be limited before these periods, i.e. by reducing manure application rates, especially if the soil is to be left uncultivated.The model results confirm the observed role of macroporosity in accelerating the breakthrough of surface applied soluble compounds and provide evidence that MACRO and SOILN may be suitable tools for predicting such phenomena, even though their calibration requires some further refinements.     

The role of rainfall temporal and spatial averaging in seasonal simulations of the terrestrial water balance

The partitioning of rainfall into surface runoff and infiltration influences many other aspects of the hydrologic cycle including evapotranspiration, deep drainage and soil moisture. This partitioning is an instantaneous non-linear process that is strongly dependent on rainfall rate, soil moisture and soil hydraulic properties. Though all rainfall datasets involve some degree of spatial or temporal averaging, it is not understood how this averaging affects simulated partitioning and the land surface water balance across a wide range of soil and climate types. We used a one-dimensional physics-based model of the near-surface unsaturated zone to compare the effects of different rainfall discretization (5-min point-scale; hourly point-scale; hourly 0.125° gridded) on the simulated partitioning of rainfall for many locations across the United States. Coarser temporal resolution rainfall data underpredicted seasonal surface runoff for all soil types except those with very high infiltration capacities (i.e., sand, loamy sand). Soils with intermediate infiltration capacities (i.e., loam, sandy loam) were the most affected, with less than half of the expected surface runoff produced in most soil types when the gridded rainfall dataset was used as input. The impact of averaging on the water balance was less extreme but non-negligible, with the hourly point-scale predictions exhibiting median evapotranspiration, drainage and soil moisture values within 10% of those predicted using the higher resolution 5-min rainfall. Water balance impacts were greater using the gridded hourly dataset, with average underpredictions of ET up to 27% in fine-grained soils. The results suggest that “hyperresolution” modelling at continental to global scales may produce inaccurate predictions if there is not parallel effort to produce higher resolution precipitation inputs or sub-grid precipitation parameterizations.     

Water and solute movement in a coarse-textured water-repellent field soil

Unstable water flow in water-repellent unsaturated soils can significantly affect the processes of infiltration and soil water redistribution. A field experiment was carried out to study the effect of water-repellency on water and bromide movement in a coarse-textured soil in the southwestern part of The Netherlands. The field data were analyzed using a relatively simple numerical model based on the standard Richards' equation for unsaturated water flow and the Fickian-based convection-dispersion equation for solute transport. Water-repellency was accounted for by multiplying the water content and the unsaturated hydraulic conductivity of the soil with F, a factor equal to the volumetric fraction of soil occupied by preferential flow paths resulting from the unstable flow process. The good comparison of simulated and measured bromide concentrations suggests that the model provides a viable method for simulating unstable water flow in water-repellent soils.     

Kationenaustauschkapazität als Grundlage für die Schätzung der Schwermetallmigration im Boden

The adsorption/desorption ratio is an important quantity of the displacement of heavy metals in the soil. Adsorption isotherms as controlled quantities are suitable for the development of a transport model. With the aid of the T value the sorption coefficients and distribution quotients can be determined for different soils. By two examples of simulation the migrations of Cd and Pb were calculated with soil samples of warp clay/gley and loam/para-brown earth. It was found, inter alia, that with increasing time of input the concentration of dissolved and adsorbed heavy metals grows and that the added heavy-metal ions are absorbed in the uppermost layers already. For cases of continuous input the simulation model is recommended for the practice to estimate the migration of heavy metals in soils.     

Effects of antecedent moisture and macroporosity on infiltration and water flow in frozen soil

Infiltration into frozen soil plays an important role in soil freeze–thaw and snowmelt-driven hydrological processes. To better understand the complex thermal energy and water transport mechanisms involved, the influence of antecedent moisture content and macroporosity on infiltration into frozen soil was investigated. Ponded infiltration experiments on frozen macroporous and non-macroporous soil columns revealed that dry macroporous soil produced infiltration rates reaching 10³ to 10⁴ mm day⁻¹, two to three orders of magnitude larger than dry non-macroporous soil. Results suggest that rapid infiltration and drainage were a result of preferential flow through initially air-filled macropores. Using recorded flow rates and measured macropore characteristics, calculations indicated that a combination of both saturated flow and unsaturated film flow likely occurred within macropores. Under wet conditions, regardless of the presence of macropores, infiltration was restricted by the slow thawing rate of pore ice, producing infiltration rates of 2.8 to 5.0 mm day⁻¹. Reduced preferential flow under wet conditions was attributed to a combination of soil swelling, due to smectite-rich clay (that reduced macropore volume), and pore ice blockage within macropores. In comparison, dry soil column experiments demonstrated that macropores provided conduits for water and thermal energy to bypass the frozen matrix during infiltration, reducing thaw rates compared with non-macroporous soils. Overall, results showed the dominant control of antecedent moisture content on the initiation, timing, and magnitude of infiltration and flow in frozen macroporous soils, as well as the important role of macropore connectivity. The study provides an important data set that can aid the development of hydrological models that consider the interacting effects of soil freeze–thaw and preferential flow on snowmelt partitioning in cold regions.