Rates of reaction of pyrite and marcasite with ferric iron at pH 2

The relative reactivities of pulverized samples (100–200 mesh) of 3 marcasite and 7 pyrite specimens from various sources were determined at 25°C and pH 2.0 in ferric chloride solutions with initial ferric iron concentrations of 10^?3 molal. The rate of the reaction:

$\text{FeS}{}_2\text{+ 14}\text{Fe}{}^{\mathrm{3+}}\text{+ 8}\text{H}{}_2\text{O}\text{= 15}\text{Fe}{}^{\mathrm{2+}}\text{+ 2}\text{SO}{}^{\mathrm{2?}}{}_4\text{+ 16}\text{H}{}^{\mathrm{+}}$

was determined by calculating the rate of reduction of aqueous ferric ion from measured oxidation-reduction potentials. The reaction follows the rate law:

where m_Fe³⁺ is the molal concentration of uncomplexed ferric iron, k is the rate constant and $\text{A}\text{M}$ is the surface area of reacting solid to mass of solution ratio. The measured rate constants, k, range from 1.0 × 10^?4 to 2.7 × 10^?4 sec^?1 ± 5%, with lower-temperature/early diagenetic pyrite having the smallest rate constants, marcasite intermediate, and pyrite of higher-temperature hydrothermal and metamorphic origin having the greatest rate constants. Geologically, these small relative differences between the rate constants are not significant, so the fundamental reactivities of marcasite and pyrite are not appreciably different.The activation energy of the reaction for a hydrothermal pyrite in the temperature interval of 25 to 50°C is 92 kJ mol^?1. This relatively high activation energy indicates that a surface reaction controls the rate over this temperature range. The BET-measured specific surface area for lower-temperature/early diagenetic pyrite is an order of magnitude greater than that for pyrite of higher-temperature origin. Consequently, since the lower-temperature types have a much greater $\text{A}\text{M}$ ratio, they appear to be more reactive per unit mass than the higher temperature types.     

Gibbsite solubility and thermodynamic properties of hydroxy-aluminum ions in aqueous solution at 25°C

Solubility curves were determined for a synthetic gibbsite and a natural gibbsite (Minas Gerais, Brazil) from pH 4 to 9, in 0.2% gibbsite suspensions in 0.01 M NaNO₃ that were buffered by low concentrations of non-complexing buffer agents. Equilibrium solubility was approached from oversaturation (in suspensions spiked with Al(NO₃)₃ solution), and also from undersaturation in some synthetic gibbsite suspensions. Mononuclear Al ion concentrations and pH values were periodically determined. Within 1 month or less, data from over-and undersaturated suspensions of synthetic gibbsite converged to describe an equilibrium solubility curve. A downward shift of the solubility curve, beginning at pH 6.7, indicates that a phase more stable than gibbsite controls Al solubility in alkaline systems. Extrapolation of the initial portion of the high-pH side of the synthetic gibbsite solubility curve provides the first unified equilibrium experimental model of Al ion speciation in waters from pH 4 to 9.The significant mononuclear ion species at equilibrium with gibbsite are Al³⁺, AlOH²⁺, Al(OH)⁺₂ and Al(OH)^?₄, and their ion activity products are $\text{1K}{}_{50}\text{= 1.29 × 10}{}^8$, $\text{1K}{}_{\mathrm{s1}}\text{= 1.33 × 10}{}^3$, $\text{1K}{}_{\mathrm{s2}}\text{= 9.49 × 10}{}^{\mathrm{?3}}$ and $\text{1K}{}_{\mathrm{s4}}\text{= 8.94 × 10}{}^{\mathrm{?15}}$. The calculated standard Gibbs free energies of formation (ΔG°_f) for the synthetic gibbsite and the A1OH²⁺, Al(OH)⁺₂ and Al(OH)^?₄ ions are ?276.0, ?166.9, ?216.5 and ?313.5 kcal mol^?1, respectively. These ΔG°_f values are based on the recently revised ΔG°_f value for Al³⁺ (?117.0 ± 0.3 kcal mol_?1) and carry the same uncertainty. The ΔG°_f of the natural gibbsite is ?275.1 ± 0.4 kcal mol^?, which suggests that a range of ΔG°_f values can exist even for relatively simple natural minerals.     

An electrochemical study of Ni2+, Co2+, and Zn2+ ions in melts of composition CaMgSi2O6

Cyclic voltammetry has been done for Ni²⁺, Co²⁺, and Zn²⁺ in melts of diopside composition in the temperature range 1425 to 1575°C. Voltammetric curves for all three ions excellently match theoretical curves for uncomplicated, reversible charge transfer at the Pt electrode. This implies that the neutral metal atoms remain dissolved in the melt. The reference electrode is a form of oxygen electrode. Relative to that reference assigned a reduction potential of 0.00 volt, the values of standard reduction potential for the ions are $\text{E}{}^1\text{(}\text{Ni}{}^{\mathrm{2+}}\text{Ni}{}^0\text{,}\text{diopside}\text{, 1500°C) = ?0.32 ± .01}\text{V}$, $\text{E}{}^1\text{(}\text{Co}{}^{\mathrm{2+}}\text{Co}{}^0\text{,}\text{diopside}\text{, 1500°C) = ?0.45 ± .02}\text{V}$, and $\text{E}{}^1\text{(}\text{Zn}{}^{\mathrm{2+}}\text{Zn}{}^0\text{,}\text{diopside}\text{, 1500°C) = ?0.53 ± .01}\text{V}$. The electrode reactions are rapid, with first order rate constants of the order of 10^?2 cm/sec. Diffusion coefficients were found to be 2.6 × 10^?6 cm²/sec for Ni²⁺, 3.4 × 10^?6 cm²/sec for Co²⁺, and 3.8 × 10^?6 cm²/sec for Zn²⁺ at 1500°C. The value of $\text{E1}$ ($\text{Ni}{}^{\mathrm{2+}}\text{Ni}{}^0$, diopside) is a linear function of temperature over the range studied, with values of ?0.35 V at 1425°C and ?0.29 V at 1575°C. At constant temperature the value of $\text{E}{}^1\text{(}\text{Ni}{}^{\mathrm{2+}}\text{Ni}{}^0\text{, 1525°C}$) was not observed to vary with composition over the range CaO · MgO · 2SiO₂ to CaO·MgO·3SiO₂ or from 1.67 CaO·0.33MgO·2SiO₂ to 0.5 CaO·1.5MgO·2SiO₂. The value for the diffusion coefficient for Ni²⁺ decreased by an order of magnitude at 1525°C over the compositional range CaO · MgO · 1.25SiO₂ to CaO · MgO · 3SiO₂. This is consistent with a mechanism by which Ni²⁺ ions diffuse by moving from one octahedral coordination site to another in the melt, with the same Ni²⁺ species discharging at the cathode regardless of the SiO₂ concentration in the melt.     

Solubility product of galena at 298°K: A possible explanation for apparent supersaturation in nature

The synthetic chelating agent ethylenediaminetetraacetic acid (EDTA) has been used to evaluate the stoichiometric solubility product of galena (PbS) at 298°K: $\text{K}{}_{\mathrm{s2}}\text{=}{}^{\mathrm{a}}\text{Pb}{}^{\mathrm{2+}}{}^{\mathrm{a}}\text{HS}{}^{\mathrm{?}}{}^{\mathrm{a}}\text{H}{}^{\mathrm{+}}$ This method circumvents the possible uncertainties in the stoichiometry and stability of lead sulfide complexes. At infinite dilution, $\text{Log K}{}_{\mathrm{s2}}\text{= ?12.25 ±0.17}$, and at an ionic strength corresponding to seawater ($\text{I = 0.7 M}$), $\text{Log K}{}_{\mathrm{s2}}\text{= ?11.73 ± 0.05}$. Using the value of $\text{K}{}_{\mathrm{s2}}$ at infinite dilution, and the free energies of formation of HS^? and Pb²⁺ at 298°K (literature values), the free energy of formation of PbS at 298°K is computed to be $\text{?79.1 ± 0.8 KJ/mol (?18.9 Kcal/mol)}$. Galena is shown to be more than two orders of magnitude more soluble than indicated by calculations based on previous thermodynamic data.     

Revised values for the Gibbs free energy of formation of [Al(OH)4 aq−], diaspore,boehmite and bayerite at 298.15 K and 1 bar,the thermodynamic properties of kaolinite to 800 K and 1 bar,and the heats of solution of several gibbsite samples

Solution calorimetric measurements compared with solubility determinations from the literature for the same samples of gibbsite have provided a direct thermochemical cycle through which the Gibbs free energy of formation of [Al(OH)_{4 aq}^?] can be determined. The Gibbs free energy of formation of [Al(OH)_{4 aq}^?] at 298.15 K is ?1305 ± 1 kJ/mol. These heat-of-solution results show no significant difference in the thermodynamic properties of gibbsite particles in the range from 50 to 0.05 μm.The Gibbs free energies of formation at 298.15 K and 1 bar pressure of diaspore, boehmite and bayerite are ?9210 ± 5.0, ?918.4 ± 2.1 and ?1153 ± 2 kJ/mol based upon the Gibbs free energy of [A1(OH)_{4 aq}^?] calculated in this paper and the acceptance of ?1582.2 ± 1.3 and ?1154.9 ± 1.2 kJ/mol for the Gibbs free energy of formation of corundum and gibbsite, respectively.Values for the Gibbs free energy formation of [Al(OH)_{2 aq}⁺] and [AlO_{2 aq}^?] were also calculated as ?914.2 ± 2.1 and ?830.9 ± 2.1 kJ/mol, respectively. The use of [AlC_{2 aq}^?] as a chemical species is discouraged.A revised Gibbs free energy of formation for [H₄SiO_4aq⁰] was recalculated from calorimetric data yielding a value of ?1307.5 ± 1.7 kJ/mol which is in good agreement with the results obtained from several solubility studies.Smoothed values for the thermodynamic functions C_P⁰, ($\text{H}{}_{\mathrm{T}}{}^0\text{- H}{}_{298}{}^0\text{)}\text{T}$, $\text{(}\text{G}{}_{\mathrm{T}}{}^0\text{- H}{}_{298}{}^0\text{)}\text{T}$, S_T⁰ - S₀⁰, $\text{ΔH}{}_{\mathrm{?,298}}{}^0$ kaolinite are listed at integral temperatures between 298.15 and 800 K. The heat capacity of kaolinite at temperatures between 250 and 800 K may be calculated from the following equation: C_P⁰ = 1430.26 ? 0.78850 T + 3.0340 × 10^?4T² ?1.85158 × 10^?4T²$\text{1}\text{2}\text{+ 8.3341 × 10}{}^6\text{T}{}^{\mathrm{?2}}$.The thermodynamic properties of most of the geologically important Al-bearing phases have been referenced to the same reference state for Al, namely gibbsite.     

Complex formation in the ternary system Mg(II)-CO2-H2O

The carbonato and hydrogencarbonato complexes of Mg²⁺ were investigated at 25 and 50° in solutions of the constant ClO₄^? molality (3 M) consisting preponderantly of NaClO₄. The experimental data could be explained assuming the following equilibria: Mg²⁺ + CO_2B + H₂O ag MgHCO⁺₃ + H⁺, $\text{log}{}^1\text{β}{}_1\text{= ?7.64}{}_4\text{± 0.01}{}_7\text{(25°), ?7.46}{}_2\text{± 0.01}{}_1\text{(50°)}$, Mg²⁺ + 2 CO_2g + 2 H₂Oag Mg(HCO₃)⁰₂ ± 2 H⁺, $\text{log}{}^1\text{β}{}_2\text{= ?15.00 ± 0.14 (25°)}$, ?15.37 ± 0.39 (50°), Mg²⁺ + CO_2g + H₂Oag MgCO⁰₃ + 2 H⁺, $\text{log}{}^1\text{k}{}_1\text{= ?15.64 ± 0.06 (25°)}$,?15.23 ± 0.02 (50°), with the assumption γ_MgCO3⁰ = γ_Mg(HCO3)⁰2, ΔG⁰(I = 0) for the reaction MgCO⁰₃ + CO_2g + H₂O = Mg(HCO₃)⁰₂ was estimated to be ?3.9₁ ± 0.8₆ and 0.6 ± 2.4 kJ/mol at 25 and 50°C, respectively. The abundance of carbonate linked Mg(II) species in fresh water systems is discussed.     

Partial molal volume calculations for the dissolution of aged amorphous silica in salt water and seawater at 0–2°C

Measurement of solubility as a function of pressure allows calculation of $\text{3}\text{V}\text{?}{}_1$. Using this experimental approach, the best estimate of $\text{3}\text{V}\text{?}{}_1$ for the dissolution of aged amorphous silica in salt water or seawater at 0–2°C is ?9.9 cm³ mol^?1 (standard error = 0.4 cm³ mol^?1). This gives , which compares well with other published values of .     

Use of Pitzer's equations to determine the media effect on the formation of lead chloro complexes

The spectrophotometric measurements of chloro complexes of lead in aqueous HCl, NaCl, MgCl₂ and CaCl₂ solutions at 25°C have been analyzed using Pitzer's specific interaction equations. Parameters for activity coefficients of the complexes PbCl⁺, PbCl₂⁰ and PbCl₃^? have been determined for the various media. Values of $\text{K}{}_1\text{= 30.0 ± 0.6}$, $\text{K}{}_2\text{= 106.7 ± 2.1}$ and $\text{K}{}_3\text{= 73.0 ± 1.5}$ were obtained for the cumulative formation constants. [$\text{Pb}{}^{\mathrm{2+}}\text{+ nCl}{}^{\mathrm{?}}\text{→ PbCl}{}_{\mathrm{n}}{}^{\mathrm{2?n}}\text{)}$]. These values are in reasonable agreement with literature data. The Pitzer parameters for the PbCl ion pairs in various media were used to calculate the speciation of Pb²⁺ in an artificial seawater solution.     

Prediction of Gibbs free energies of calcite-type carbonates and the equilibrium distribution of trace elements between carbonates and aqueous solutions

A linear correlation exists between the standard Gibbs free energies of formation of calcite-type carbonates (MCO3) and the corresponding conventional standard Gibbs free energies of formation of the aqueous divalent cations (M2+) at 25 °C and 1 bar ΔGMCO30 = m(ΔGf,M2+0) ? 141,200 cal · mole?1 where m is equal to 0.9715. This relationship enables prediction of the standard free energies of formation of numerous hypothetical carbonates with the calcite structure. Associated uncertainties typically range from about ± 250 to 600 cal · mole?1. An important consequence of the above correlation is that the thermodynamic equilibrium constant for the distribution of two trace elements M and N between carbonate mineral and aqueous solution at 25 °C and 1 bar is proportional to the free energy difference between the corresponding two aqueous ions: In Combination of predicted standard free energies, entropies and volumes of carbonate minerals at 25°C and 1 bar with standard free energies of aqueous ions and the equation of state in Helgesonet al. (1981) enables prediction of the thermodynamic equilibrium constant for trace element distribution between carbonates and aqueous solutions at elevated temperatures and pressures. Interpretation of the thermodynamic equilibrium constant in terms of concentration ratios in the aqueous phase is considerably simplified if pairs of divalent trace elements are considered that have very similar ionic radii (e.g., $\text{Sr}{}^{\mathrm{2+}}\text{Pb}{}^{\mathrm{2+}}$, $\text{Mg}{}^{\mathrm{2+}}\text{Zn}{}^{\mathrm{2+}}$). In combination with data for the stabilities of complex ions in aqueous solutions, the above calculations enable useful limits to be placed on the concentrations of trace elements in hydrothermal solutions.     

Density calculations for silicate liquids. I. Revised method for aluminosilicate compositions

Equations are developed for calculating the density of aluminosilicate liquids as a function of composition and temperature. The mean molar volume at reference temperature T_r, is given by $\text{V}{}_{\mathrm{r}}\text{= ∑X}{}_{\mathrm{i}}\text{V}\text{?}{}^{\mathrm{o}}{}_{\mathrm{i}}\text{+ X}{}_{\mathrm{A}}\text{V}\text{?}{}^{\mathrm{o}}{}_{\mathrm{A}}$, where the summation is taken over all oxide components except A1₂O₃, X stands for mole fraction, terms are constants derived independently from an analysis of volume-composition relations in alumina-free silicate liquids, and $\text{V}\text{?}{}^{\mathrm{o}}{}_{\mathrm{A}}$ is the composition-dependent apparent partial molar volume of Al₂O₃. The thermal expansion coefficient of aluminosilicate liquids is given by $\text{α = ∑X}{}_{\mathrm{i}}\text{}\text{?}\text{ga}{}_{\mathrm{i}}{}^{\mathrm{o}}\text{+ X}{}_{\mathrm{A}}\text{}\text{?}\text{ga}{}_{\mathrm{A}}{}^{\mathrm{o}}$, where $\text{}\text{?}\text{ga}{}_{\mathrm{i}}{}^{\mathrm{o}}$ terms are constants independent of temperature and composition, and $\text{}\text{?}\text{ga}{}^{\mathrm{o}}{}_{\mathrm{A}}$ is a composition-dependent term representing the effect of Al₂O₃ on the thermal expansion. Parameters necessary to calculate the volume of silicate liquids at any temperature T according to V(T) = V_rexp[α(T-T_r)], where T_r = 1400°C have been evaluated by least-square analysis of selected density measurements in aluminosilicate melts. Mean molar volumes of aluminosilicate liquids calculated according to the model equation conform to experimentally measured volumes with a root mean square difference of 0.28 $\text{cc}\text{mole}$ and an average absolute difference of 0.90% for 248 experimental observations. The compositional dependence of $\text{V}\text{?}{}^{\mathrm{o}}{}_{\mathrm{A}}$ is discussed in terms of several possible interpretations of the structural role of Al³⁺ in aluminosilicate melts.     

Dissociation constants for alkali earth and sodium borate ion pairs from 10 to 50°C

Potentiometric measurements in dilute sodium borate solutions with added alkali earth chlordie salts yield the following expressions for the dissociation constants of alkali earth borate ion pairs from 10 to 50°C:

$\text{p}\text{K(}\text{MgH}{}_2\text{BO}{}_3{}^{\mathrm{+}}\text{=1.266+0.001204 T}$

$\text{p}\text{K(}\text{CaH}{}_2\text{BO}{}_3{}^{\mathrm{+}}\text{=1.154+0.002170 T}$

$\text{p}\text{K(}\text{SrH}{}_2\text{BO}{}_3{}^{\mathrm{+}}\text{=1.033+0.001738 T}$

$\text{p}\text{K(}\text{BaH}{}_2\text{BO}{}_3{}^{\mathrm{+}}\text{=1.942+0.001850 T}$

where T is in °K. Enthalpies for the dissociation reactions at 25°C are less than 1 kcal./mole for all the alkali earth borate ion pairs.Values for pK(NaH₂BO₃°) from 5 to 55°C computed from the experimental data of Owen and King are in good agreement with those determined potentiometrically. The average value from both methods is 0.22 ± 0.1 at 25°C.Application to seawater of computed pK's for MgH₂BO₃⁺, CaH₂BO₃⁺ and NaH₂BO₃⁰ yields an apparent dissociation constant for boric acid of 8.73 vs. 8.70 measured by Lyman, 8.68 by Buch and 8.73 by Byrne and Kester.     

Constantes de formation des complexes hydroxydés de l'aluminium en solution aqueuse de 20 a 70°C

Stability constants of hydroxocomplexes of Al(III):Al(OH)²⁺ and A1(OH)₄^? have been measured in the 20–70°C temperature range by reactions involving only dissolved species. The stability constant ${}^1\text{K}{}_1$ of the first complex ion is studied by measuring pH of solutions of aluminium salts at several concentrations. ${}^1\text{β}{}_4$ of aluminate ion is deduced from equilibrium constants of the reaction between the trioxalato aluminium (III) complex ion and Al³⁺ in acid medium, and between the same complex ion and A1(OH)₄^? in alkaline medium. The K values and the associated ΔH are ${}^1\text{K}{}_1\text{= 10}{}^{\mathrm{?5.00}}$ and ΔH₁ = 11.8 Kcal; ${}^1\text{β}{}_4\text{= 10}{}^{\mathrm{?22.20}}$ and ΔH₄ = 42.45 Kcal. These last results are not in agreement with the values of recent tables for $\text{ΔG}{}^0\text{?}$ and $\text{ΔH}{}^0\text{?}$ of Al³⁺ and Al(OH)₄^?. We suggest a consistent set of data for dissolved and solid Al species and for some aluminosilicates.     

The thermal significance of potassium feldspar K-Ar ages inferred from 40Ar39Ar age spectrum results

${}^{40}\text{Ar}{}^{39}\text{Ar}$ age spectrum analyses of three microcline separates from the Separation Point Batholith, northwest Nelson, New Zealand, which cooled slowly (~5°C-Ma^?1) through the temperature zone of partial radiogenic ⁴⁰Ar accumulation are characterized by a linear age increase over the first 65 percent of gas release with the lowest ages (~80 Ma) corresponding to the time that the samples cooled below about 100°C. The last 35 percent of ³⁹Ar released from the microclines yields plateau ages (103,99 and 93 Ma) which reflect the different bulk mineral ages, and correspond to cooling temperatures between about 130 to 160°C. Theoretical calculations confirm the likelihood of diffusion gradients in feldspars cooling at rates ≤5°C-Ma^?1. Diffusion parameters calculated from the ³⁹Ar release yield an activation energy, E = 28.8 ± 1.9 kcal-mol^?1, and a frequency factor/grain size parameter, $\text{D}{}_0\text{l}{}^2\text{= 5.6}{}_{\mathrm{?3.9}}{}^{\mathrm{+14}}\text{sec}{}^{\mathrm{?1}}$. This Arrhenius relationship corresponds to a closure temperature of 132 ± 13°C which is very similar to the independently estimated temperature. From the observed diffusion compensation correlation, this $\text{D}{}_0\text{l}{}^2$ implies an average diffusion half-width of about 3 μm, similar to the half-width of the perthite lamellae in the feldspars. The range in microcline K-Ar ages from the Separation Point Batholith is the result of relatively small temperature differences within the pluton during cooling. Comparison of the diffusion laws determined for microcline with those for anorthoclases and other homogeneous K-feldspars (E = 40 to 52 kcal-mol^?1) reveals that Ar diffusion is more highly temperature dependent in the disordered structural state than in the ordered structural state. Previously published U-shaped age spectra are probably the result of the superimposition of excess ⁴⁰Ar upon diffusion profiles of the kind described here.     

Mineral-solution equilibria—III. The system Na2OAl2O3SiO2H2OHCl

Chemical equilibrium between sodium-aluminum silicate minerals and chloride bearing fluid has been experimentally determined in the range 500–700°C at 1 kbar, using rapid-quench hydrothermal methods and two modifications of the Ag + AgCl acid buffer technique. The temperature dependence of the thermodynamic equilibrium constant (K) for the reaction $\text{NaAlSi}{}_3\text{O}{}_8\text{+ HCl}{}^{\mathrm{o}}\text{= NaCl}{}^{\mathrm{o}}\text{+}\text{1}\text{2Al}{}_2\text{SiO}{}_5\text{, +}\text{5}\text{2SiO}{}_2\text{+}\text{1}\text{2H}{}_2\text{O}$ Albite Andalusite Qtz. can be described by the following equation: log k = ?4.437 + 5205.6/T(K) The data from this study are consistent with experimental results reported by Montoya and Hemley (1975) for lower temperature equilibria defined by the assemblages albite + paragonite + quartz + fluid and paragonite + andalusite + quartz + fluid. Values of the equilibrium constants for the above reactions were used to estimate the difference in Gibbs free energy of formation between NaCl^o and HCl^o in the range 400–700°C and 1–2 kbar. Similar calculations using data from phase equilibrium studies reported in the literature were made to determine the difference in Gibbs free energy of formation between KCl^o and HCl^o. These data permit modelling of the chemical interaction between muscovite + kspar + paragonite + albite + quartz assemblages and chloride-bearing hydrothermal fluids.     

The effect of pressure on the solubility of minerals in water and seawater

The effect of presure on the solubility of minerals in water and seawater can be estimated from In

$\text{(}\text{K}{}^{\mathrm{P}}{}_{\mathrm{sp}}\text{K}{}^0{}_{\mathrm{sp}}\text{) +}\text{(?ΔVP + 0.5ΔKP}{}^2\text{)}\text{RT}$

where the volume (ΔV) and compressibility (ΔK) changes at atmospheric pressure (P = 0) are given by

$\text{ΔV =}\text{V}\text{?}\text{(M}{}^{\mathrm{+}}\text{, X}{}^{\mathrm{?}}\text{) ?}\text{V}\text{?}\text{[MX(s)]ΔK =}\text{K}\text{?}\text{(M}{}^{\mathrm{+}}\text{, X}{}^{\mathrm{?}}\text{) ?}\text{K}\text{?}\text{[MX(s)]}$

Values of the partial molal volume ($\text{V}\text{?}$) and compressibilty ($\text{K}\text{?}$) in water and seawater have been tabulated for some ions from 0 to 50°C. The compressibility change is quite large (~10 × 10^?3 cm³ bar^?1 mol^?1) for the solubility of most minerals. This large compressibility change accounts for the large differences observed between values of ΔV obtained from linear plots of In K_sp versus P and molal volume data (Macdonald and North, 1974; North, 1974). Calculated values of $\text{K}{}^{\mathrm{P}}{}_{\mathrm{sp}}\text{K}{}^{\mathrm{o}}{}_{\mathrm{sp}}$ for the solubility of CaCO₃, SrSO₄ and CaF₂ in water were found to be in good agreement with direct measurements (Macdonald and North, 1974). Similar calculations for the solubility of minerals in seawater are also in good agreement with direct measurements (Ingle, 1975) providing that the surface of the solid phase is not appreciably altered.     

Thermodynamic stability studies of the basic copper carbonate mineral,malachite

Natural malachite is a well defined solid demonstrating reproducible solubility behavior over a wide range of pH. The following equilibrium constants associated with the malachite dissolution equilibrium at 25°C, 1 atm were determined:

(infinite dilution)

$\text{K}{}^1{}_{\mathrm{sp}}\text{=}\text{[Cu}{}^{\mathrm{2+}}\text{]}{}^2\text{[CO}{}^{\mathrm{2?}}{}_3\text{]K}{}^2{}_{\mathrm{w}}\text{a}{}^2{}_{\mathrm{H+}}\text{= 10. ± 0.2 × 10}{}^{\mathrm{?32}}$

(0.72 ionic strength)

(36.9‰ salinity seawater). The temperature dependence of a “mixed” equilibrium constant, K_sp⁺, of the form:

has been measured at I = 0.72, yielding the relationship:

$\text{log K}{}^2{}_{\mathrm{sp}}\text{= (? 9.8 ± 0.03) × 10}{}^4\text{(}\text{1}\text{T°K}\text{) + (1.52 ± 0.09)}$

within a 5–25°C temperature range. The effect of pressure on the solubility of malachite in water and seawater was estimated from partial molar volume and compressibility data. For 25 °C at infinite dilution $\text{K'}{}_{\mathrm{sp}}\text{(1000 bar)}\text{K'}{}_{\mathrm{sp}}\text{(0)}\text{= 240}$ and in seawater $\text{K′}{}_{\mathrm{sp}}\text{(1000)}\text{K'}{}_{\mathrm{sp}}\text{(0)}\text{= 44}$.Comparison of stoichiometric and apparent malachite equilibrium constants has been used to estimate the extent of copper(II) ion interaction at the ionic strength of seawater. In dilute carbonate medium (total alkalinity, TA = 2.4 meq/kg H₂O, pH 8.3), 2.9% of total dissolved copper exists as the free copper(II) ion and in seawater (S = 36.9%., TA = 2.3 meq/kg H₂O, pH = 8.1), $\text{[Cu}{}^{\mathrm{2+}}\text{]}\text{T(Cu)}$ is 3.1%.Total dissolved copper levels of approximately 450–750 nMol/Kg are necessary to attain malachite saturation conditions in the open ocean. Observations of malachite particles suspended in seawater must be explained by precipitation or solid phase substitution reactions from localized environments rather than by direct precipitation from bulk seawater.     

Oxygen and sulfur isotope equilibria in the BaSO4HSO4−H2O system from 110 to 350°C and applications

Oxygen isotope exchange between BaSO₄ and H₂O from 110 to 350°C was studied using 1 m H₂SO₄-1 m NaCl and 1 m NaCl solutions to recrystallize the barite. The slow exchange rate (only 7% exchange after 1 yr at 110°C and 91% exchange after 22 days at 350°C in 1 m NaCl solution) prompted the use of the partial equilibrium technique. However, runs at 300 and 350°C were checked by complete exchange experiments. The temperature calibration curve for the isotope exchange is calculated giving most weight to the high temperature runs where the partial equilibrium technique can be tested. Oxygen isotope fractionation factors (α) in 1 m NaCl solution (110–350°C), assuming a value of 1.0407 for α_CO2H2O at 25°C, are:

.These data, when corrected for ion hydration effects in solution (Truesdell, 1974), give the fractionation factors in pure water:

.In the 1 m H₂SO₄-1 m NaCl runs, sulfur isotope fractionation between HSO^?₄ and BaSO₄ is less than the detection limit of 0.4%. A barite-sulfide geothermometer is obtained by combining HSO^?₄H₂S and sulfide-H₂S calibration data.Barite in the Derbyshire ore field, U.K., appears to have precipitated in isotopic equilibrium with water and sulfur in the ore fluid at temperatures less than 150°C. At the Tui Mine, New Zealand, the barite-water geothermometer indicates temperatures of late stage mineralization in the range 100–200°C. A temperature of 350 ± 20°C is obtained from the barite-pyrite geothermometer at the Yauricocha copper deposit, Peru, and oxygen isotope analyses of the barite are consistent with a magmatic origin for the ore fluids.     

Determination of the 87Rb decay constant

The decay constant ⁸⁷Rb has been redetermined by measuring the amount of radiogenic ⁸⁷Sr produced over a period of 19 years, in 20 g samples of purified RbClO₄, using isotope dilution techniques. The rubidium sample was spiked with ⁸⁴Sr and the nanogram quantities of strontium separated by coprecipitation with Ba(NO₃)₂. Analyses were carried out on a 25cm, 90° sector mass spectrometer equipped with a Spiraltron electron multiplier. Measurement of three independent ratios permitted continuous monitoring of the ion beam fractionation. The average of nine determinations gives a value for the decay constant of $\text{1.419(±0.012) × 10}{}^{\mathrm{?11}}\text{yr}{}^{\mathrm{?1}}\text{(2σ)}$. [$\text{τ}{}_{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}\text{= 4.89(±0.04) × 10}{}^{10}\text{yr}$.]