Scattering of water wave by a submerged horizontal plate and a submerged permeable breakwater

Based on a two-dimensional linear water wave theory, this study develops the boundary element method (BEM) to examine normally incident wave scattering by a fixed, submerged, horizontal, impermeable plate and a submerged permeable breakwater in water of finite depth. Numerical results for the transmission coefficients are also presented. In addition, the numerical technique's accuracy is demonstrated by comparing the numerical results with previously published numerical and experimental ones. According to that comparison, the transmission coefficient relies not only on the submergence of the horizontal impermeable plate and the height of the permeable breakwater, but also on the distance between horizontal plate and permeable breakwater. Results presented herein confirm that the transmission coefficient is minimum for the distance approximately equal to four times the water depth.     

Flow field analysis of submerged horizontal plate type breakwater

Submerged horizontal plate can be considered as a new concept breakwater. In order to reveal the wave elimination mechanism of this type breakwater, boundary element method is utilized to investigate the velocity field around plate carefully. The flow field analysis shows that the interaction between incident wave and reverse flow caused by submerged plate will lead to the formation of wave elimination area around both sides of the plate. The velocity magnitude of flow field has been reduced and this is the main reason of wave elimination.     

Wave motion over a submerged breakwater with an upper horizontal porous plate and a lower horizontal solid plate

This study examines the hydrodynamic performance of a modified two-layer horizontal-plate breakwater. The breakwater consists of an upper submerged horizontal porous plate and a lower submerged horizontal solid plate. By means of the matched eigenfunction expansion method, a linear analytical solution is developed for the interaction of water waves with the structure. Then the reflection coefficient, the transmission coefficient, the energy-loss coefficient and the wave forces acting on the plates are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a single submerged horizontal solid plate and a single submerged horizontal porous plate. Numerical results show that with a suitable geometrical porosity of the upper plate, the uplift wave forces on both plates can be controlled at a low level. Numerical results also show that the transmission coefficient will be always small if the dimensionless plate length (plate length versus incident wavelength) exceeds a certain moderate value. This is rather significant for practical engineering, as the incident wavelength varies over a wide range in practice. Moreover, it is found that the hydrodynamic performance of the present structure may be further enhanced if the lower plate is also perforated.     

聚焦波作用下透水潜堤消波特性数值模拟研究

基于非静压数值计算模型,本文系统研究了聚焦波作用下透水潜堤的消波特性,通过设置合理的计算工况,详细分析了波高、堤顶水深、谱峰周期、孔隙率以及堤顶宽度5种因素对透水潜堤消波特性的影响。与此同时,本文将透水潜堤的计算结果同不透水潜堤的计算结果进行了对比分析。计算结果表明：透水潜堤对聚焦波的消减作用要强于不透水潜堤,从而说明,透水潜堤能更有效地降低畸形波对海岸基础设施的影响;波高和堤顶水深是影响潜堤消波特性的重要因素,随入射波高增加、堤顶水深减小,透水潜堤对波浪的消减作用逐渐增强。透水潜堤对长周期波浪的消波效果较差。在本文考虑的孔隙率范围内,孔隙率越大,透水潜堤消波效果越好;当孔隙率为0.4,堤顶宽度为0.612 5 m时,透水潜堤可消减54%的入射波能,比不透水潜堤对入射波能的消减增加36.1%。本文研究结果可为进一步认识透水潜堤的消波特性和海岸防护工程设计提供相应的参考。     

Wave interaction with a perforated wall breakwater with a submerged horizontal porous plate

This study examines the hydrodynamic performance of a new perforated-wall breakwater. The breakwater consists of a perforated front wall, a solid back wall and a submerged horizontal porous plate installed between them. The horizontal porous plate enhances the stability and wave-absorbing capacity of the structure. An analytical solution based on linear potential theory is developed for the interaction of water waves with the new proposed breakwater. According to the division of the structure, the whole fluid domain is divided into three sub-domains, and the velocity potential in each domain is obtained using the matched eigenfunction method. Then the reflection coefficient and the wave forces and moments on the perforated front wall and the submerged horizontal porous plate are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a perforated-wall breakwater with a submerged horizontal solid plate [Yip, T.L., Chwang, A.T., 2000. Perforated wall breakwater with internal horiontal plate. Journal of Engineering Mechanics ASCE 126 (5), 533–538] and a vertical wall with a submerged horizontal porous plate [Wu, J.H., Wan, Z.P., Fang, Y., 1998. Wave reflection by a vertical wall with a horizontal submerged porous plate. Ocean Engineering 25 (9), 767–779]. Numerical results show that with suitable geometric porosity of the front wall and horizontal plate, the reflection coefficient will be always rather small if the relative wave absorbing chamber width (distance between the front and back walls versus incident wavelength) exceeds a certain small value. In addition, the wave force and moment on the horizontal plate decrease significantly with the increase of the plate porosity.     

Physical model studies on wave transmission of a submerged inclined plate breakwater

This paper examines the results of physical model studies conducted in a monochromatic wave flume, to evaluate the wave transmission characteristics of a submerged plate breakwater consisting of a fixed plate of 0.50 m length and 0.003 m thickness. The model was oriented at varying inclinations and submergence. The influence of wave steepness, relative depth, relative submergence and angle of inclination on wave transmission was analysed. It was found that the horizontal plate is effective for short waves with steepness parameter higher than 5×10^?3 in relative depth grater than 0.21. The plate oriented at an angle of inclination of 60° is found to be effective for the entire ranges of wave parameters considered for the study and it reduces the wave height by about 40%.     

Higher harmonics induced by a submerged horizontal plate and a submerged rectangular step in a wave flume

The decomposition of a monochromatic wave over a submerged plate is investigated experimentally in a wave flume. Bound and free higher harmonic modes propagating upstream and downstream the structure are discriminated by means of moving resistive probes. The first-order analysis shows a resonant behaviour linked to the ratio of the plate's width and the fundamental mode wavelength over the plate. The second-order analysis shows an energy transfer from the fundamental mode towards free harmonics propagating downstream the structure. This transfer is linked to the ratio of the width of the plate and the bound harmonic wavelength over the plate. We also performed experiments with a submerged step to compare the efficiency of both structures. The submerged plate is shown to be a more efficient breakwater than the step, at the first as well as the second-order.     

Propagation of solitary waves over a submerged permeable breakwater

We study the interactions between a non-breaking solitary wave and a submerged permeable breakwater experimentally and numerically. The particle image velocimetry (PIV) technique is employed to measure instantaneous free surface displacements and velocity fields in the vicinity of a porous dike. The porous medium, consisting of uniform glass spheres, is mounted on the seafloor. Due to the limited size of each field of view (FOV) for high spatial resolution purposes, four FOVs are set in order to form a continuous flow field around the structure. Quantitative mean properties are obtained by ensemble averaging 30 repeated instantaneous measurements. The Reynolds decomposition method is then adopted to separate the velocity fluctuations for each trial to estimate the turbulent kinetic energy. In addition, a highly accurate two-dimensional model with the volume of fluid interface tracking technique is used to simulate an idealized volume-averaged porous medium. The model is based on the Volume-Averaged Reynolds Averaged Navier–Stokes equations coupled with the non-linear k–ε turbulence closure solver. Comparisons are performed between measurements and numerical results for the time histories of the free surface elevation recorded by wave gauges and the spatial distributions of free surface displacement with the corresponding velocity and turbulent kinetic energy around the permeable object imaged by the PIV system. Fairly good agreements are obtained. It is found that the measured and modeled turbulent intensities on the weather side are much larger than those on the lee side of the object, and that the magnitude of the turbulent intensity increases with increasing wave height of a solitary wave at a constant water depth. The verified numerical model is then used to estimate the energy reflection, transmission and dissipation using the energy integral method by varying the aspect ratio and the grain size of the permeable obstacle.     

Solitary wave propagation influenced by submerged breakwater

The form of Boussinesq equation derived by Nwogu （1993） using velocity at an arbitrary distance and surface elevation as variables is used to simulate wave surface elevation changes. In the numerical experiment, water depth was divided into five layers with six layer interfaces to simulate velocity at each layer interface. Besides, a physical experiment was carried out to validate numerical model and study solitary wave propagation.“Water column collapsing”method （WCCM） was used to generate solitary wave. A series of wave gauges around an impervious breakwater were set-up in the flume to measure the solitary wave shoaling, run-up, and breaking processes. The results show that the measured data and simulated data are in good agreement. Moreover, simulated and measured surface elevations were analyzed by the wavelet transform method. It shows that different wave frequencies stratified in the wavelet amplitude spectrum. Finally, horizontal and vertical velocities of each layer interface were analyzed in the process of solitary wave propagation through submerged breakwater.     

波浪与起伏水平板防波堤相互作用数值模拟

利用自主研发的基于紧致插值曲线CIP(constrained interpolation profile)方法的数学模型,开展规则波与起伏水平板防波堤相互作用的数值模拟研究。模型在笛卡尔直角坐标下建立,以CIP方法为流场基本求解器,分步求解Navier-Stokes方程,利用高精度的流体体积类型的THINC/SW (tangent of hyperbola for interface capturing with slope weighting)方法重构自由液面,采用浸入边界IBM(immersed boundary method)方法处理波浪与起伏板防波堤的耦合作用问题,通过动量源项造波方法模拟波浪的产生。重点关注波浪的浅水变形和板两端涡旋脱落的非线性现象,分析不同潜深、波要素下的板周围流场分布、板的运动响应和波浪的反透射系数。结果表明:起伏水平板主要通过能量反射、板上浅水变形和板两端的涡脱落消能,能有效减小板后波高,具有作为防波堤的可行性。     

多向聚焦波作用下透水潜堤消波特性数值模拟研究

本文采用非静压模型NHWAVE建立高精度三维波浪数值水槽,对多向聚焦波作用下透水和不透水潜堤消波特性进行数值模拟研究。通过计算结果与实验数据的对比,验证了该模型模拟多向聚焦波产生传播及多孔介质内流动的能力,进一步考虑了有效波高、水深、谱峰周期和传播角度等因素对潜堤消波特性的影响。结果表明：潜堤对多向聚焦波的最大波幅、最大水位、沿水深平均最大流速和波能均有显著消减作用,且透水潜堤因孔隙介质的存在消波性能更好。随着有效波高增大,堤顶处波浪破碎点前移,不透水潜堤消波性能受波高影响较大。水深越大,潜堤消波性能越低。透水潜堤对长周期波浪消减效果较差。传播角度越小,聚焦位置处波幅越大,波浪非线性作用越强。研究结果可为我们进一步保护沿海设施免受极端海洋环境的影响提供一定的参考     

Wave height transformation and set-up between a submerged permeable breakwater and a seawall

In this study,we investigated wave transformation and wave set-up between a submerged permeable breakwater and a seawall.Modified time-dependent mild-slope equations,which involve parameters of the porous medium,were used to calculate the wave height transformation and the mean water level change around a submerged breakwater.The numerical solution is verified with experimental data.The simulated results show that modulations of the wave profile and wave set-up are clearly observed between the submerged breakwater and the seawall.In contrast to cases without a seawall,the node or pseudo-node of wave height evolution can be found between the submerged breakwater and the seawall.Higher wave set-up occurs if the nodal or pseudo-nodal point appears near the submerged breakwater.We also examined the influence of the porosity and friction factor of the submerged permeable breakwater on wave transformation and set-up.     

Linearised water wave problems involving submerged horizontal plates

In this paper a number of related linearised water wave problems all involving thin submerged horizontal plates are considered. An integral transform approach is adopted and used to formulate integral equations in terms of unknown functions related to the jump in pressure across the plate. A Galerkin method is applied to the solution of these integral equations leading to elegant expressions for quantities of interest and a rapidly convergent numerical scheme. The focus of the paper is to demonstrate the application of this method in a number of settings including both two-dimensional problems applied to infinitely-long plates of constant width and three-dimensional problems involving circular discs. In the process we present new results including, for example, for wave-free forced oscillations of plates.     

Wave transformation over submerged permeable breakwater on porous bottom

A numerical model is presented in this study to investigate the wave transformation over a submerged permeable breakwater on a porous slope seabed. For this purpose, the time-dependent mild-slope equation is newly derived for waves propagating over two layers of porous medium. This new mild-slope equation involves the parameters of the porous medium, and it is a type of hyperbolic differential equation, therefore numerically efficient. The validity of the present model is verified based on the comparisons with the previous experiments. The effects of the permeable properties of both the porous seabed and the submerged permeable breakwater are discussed in detail. The geometry of the submerged permeable breakwater to the wave transformation is also investigated based on the numerical solutions.     

波浪在Jarlan型开孔潜堤上的运动

The wave motion over a submerged Jarlan-type breakwater consisting of a perforated front wall and a solid rear wall was investigated analytically and experimentally. An analytical solution was developed using matched eigenfunction expansions. The analytical solution was confirmed by previously known solutions for single and double submerged solid vertical plates, a multidomain boundary element method solution, and experimental data. The calculated results by the analytical solution showed that compared with double submerged vertical plates, the submerged Jarlan-type perforated breakwater had better wave-absorbing performance and lower wave forces. For engineering designs, the optimum values of the front wall porosity, relative submerged depth of the breakwater, and relative chamber width between front and rear walls were 0.1–0.2, 0.1–0.2, and 0.3–0.4, respectively. Interchanging the perforated front wall and solid rear wall may have no effect on the transmission coefficient. However, the present breakwater with a seaside perforated wall had a lower reflection coefficient.     

Experimental studies on a perforated horizontal floating plate breakwater

In recent years floating breakwaters are considered for creating calm basin under open sea conditions for short period of time. In this paper, experimental studies on the performance characteristics of a horizontal floating plate breakwater are presented. The results of this two-dimensional model study are for regular waves of shallow and intermediate water depths. Analysis of the results shows that the transmission coefficient is strongly influenced by wave steepness and relative length of breakwater. It is also found to be dependent, to a lesser extent, on the relative depth of draft. Mooring forces are found to increase with increasing wave steepness and relative depth of draft. The performance of this breakwater is compared with other types of breakwater reported by earlier workers.     

Computation of wave transmission over a shore protecting submerged breakwater

Among the offshore breakwaters which are increasingly used in shore protection projects, a bevelled block submerged breakwater with 1 on 1.67 seaward slope and a vertical shoreward face is most advantageous, especially from the point of view of optimum wave damping, minimum wave reflection and maximum sand trapping effects. Different computational methods of wave transmission coefficient of this breakwater are examined with laboratory tests. The Goda's method is found to be the simplest and most suitable in the case of the shore protecting submerged breakwater. However, the consideration of wave steepness also, in selecting the constants may yield better results with this method.     

A new approximate analytic solution for water wave scattering by a submerged horizontal porous disk

This study gives a new approximate analytic solution for water wave scattering by a submerged horizontal porous disk in the context of the linear potential theory. The solution is based on the domain decomposition method. The velocity potentials are determined by two different approaches. One approach is to adopt decompositions for velocity potentials, and the other is to expand the vertical derivative of the velocity potential on the porous disk along the radial direction. Hence the velocity potentials are determined by the matched eigenfunction expansions. Differing from previous solutions with respect to the porous disk, the present solution needs no complex dispersion relations. Thus the new solution is easier for numerical implementation. According to numerical examples, the convergence of the present solution is satisfactory. In addition, the present predictions of the wave surface elevation and the vertical wave force on the disk agree very well with previous results by different approaches. The present solution can also be extended to other structures involving disks, such as a fish cage, a porous disk with finite thickness, and a submerged elastic disk.     

V形防波堤与圆弧型防波堤之浅水波绕射作用的比较

应用椭圆余弦波的绕射理论,推导了V形防波堤的浅水波浪绕射解析解,从而对现有的Airy微幅波理论进行了有效拓展。据此理论对V形防波堤的浅水波绕射作用进行了解析计算,并与几何形状相近的圆弧型防波堤结果加以了对比。结果表明：椭圆余弦波理论计算的V形防波堤最大波浪力和最大绕射波面明显大于微幅波理论的对应值。本方法适用于张角180°的有限长直立薄壁防波堤的浅水波绕射作用计算,从而将无限长直立薄壁堤的反射波理论加以有效拓展。张角同为120°的V形堤与圆弧堤的堤后防浪效果相近,而180°圆弧堤的堤后防浪效果优于张角90°的V形堤。     

没水倾斜板式防波堤消波性能分析

提出了一种将波浪中倾斜板问题等效化简为波浪中水平板单元组的方法,该方法建立在使用分离变量法求解水工结构边值问题的基础上,并使用伽辽金法精确求解连续边界条件,确定考虑衰减波态的速度势函数,从而求解没水倾斜板结构的消波性能。等效化简法计算精度于边界元法相当,且计算单元数量少、开销低。基于二维线性势波理论,对没水倾斜板式防波堤消波性能分析显示,没水板的倾斜角度、没水深度与板长是结构消波性能的控制因素:没水倾斜板防波堤的消波性能优于没水水平板防波堤的消波性能,随着没水板结构的倾斜角度增大,没水倾斜板结构的波浪透射系数显著减小,且长板优于短板,浅板优于深板;与前人的水槽实验对比显示,相对没水深度与波陡影响结构的消波性能,且波陡造成的波浪破碎贡献了显著的波能消耗。该结论对板式防波堤的结构配置、优化设计有重要意义。