模型储罐三维地震反应振动台试验研究

针对立式钢制模型罐,进行了三维地震激励和一维地震激励振动台的动响应试验研究。结果表明:储罐在三维地震动激励下的反应与一维激励相比,加速度反应、罐壁的应变反应、储罐提离反应具有较明显的放大效应。位移反应在不同地震激励下,其放大效应不同,El Centro波激励下各测点三维激励下位移较一维激励下位移放大明显,Taft、天津波激励下各测点三维激励下位移较一维激励下位移有放大也有缩小,幅度均不大。由罐壁测点加速度功率谱分析表明:一维激励其峰值频率区域较为集中,主峰突出,能量主要集中于低频区;在三维地震激励下,频率峰值区域明显拉长,峰值点模糊,频率成份十分丰富,表现出多主峰的特点。     

卵石土场地地震反应特征振动台试验研究

为研究卵石土场地地震反应特征,基于四川成都典型卵石土场地,通过振动台模型试验研究卵石土场地在不同地震波、不同地震强度激励下的加速度峰值放大系数、加速度频谱反应及动土压力反应,并且对其场地地震反应非线性效应及土体动剪应力-动剪应变关系进行分析。结果表明：卵石土场地表层土层对地震波具有明显的放大效应,加速度峰值放大系数介于1～1.4之间,下部土层放大效应较小,加速度峰值放大系数介于0.9～1.2之间。卵石土场地对地震波具有低频放大,高频滤波的作用,滤波频率上、下限随激励强度的增大逐渐向低频方向移动。激励强度较小时,土体尚未破坏,动土压力在地震过程中逐渐增大;随着激励强度的增大,动土压力反应明显增大,表现出骤减后逐渐增大的现象。在激励强度较小时(SN1),中部土体最先进入非线性反应阶段,地震波在中部土层能量损耗最大;激励强度较大时(EL3),土体均发生了较大变形,土体最大动剪应变达到1.7%,此时卵石土场地对地震波的放大作用明显减弱。     

某全钢结构地震模拟振动台试验和理论研究

对体型不规则的全钢结构建筑进行了地震模拟振动台试验研究和理论分析，这种结构体系是由内椭球塔与外框筒连接而成的特殊结构体系。地震模拟试验结果表明这种结构体系仍然以主振型为主，内椭球塔与外框筒连接方式能够满足设计要求。文末采用SAP2000程序对结构模型进行三维受力分析，沿最不利加振方向的理论分析结果与振动台试验结果显示该结构在设计地震作用下，具有足够的安全性。     

饱和软土自由场地地震反应特性振动台试验

为了解软土自由场地地震反应特性,开展饱和软土自由场地地震反应特性大型振动台模型试验。分别从模型体系自振特性、震陷位移及不同土层深度测点的加速度、动孔压比等动力响应指标方面,较为深入和全面地分析饱和软土自由场地地震反应规律、破坏机理。同时还分析模型箱的"边界效应"以验证试验土箱的合理性、有效性和测试仪器性能,并由此进一步确定模型地基有效工作区域。研究表明:(1)地震动作用下,饱和软土自由场地特征频率降低,阻尼增大;(2)饱和软土自由场地对水平输入地震波具有短周期滤波、长周期放大效应,且强震作用下地基失效并表现为减隔震作用;(3)饱和软土自由场地动孔压比优势区域位于浅埋土层,并随着输入地震动强度的增大,该区域动孔压比优势逐渐减弱。该研究可为非自由软土场地试验研究提供必要的技术经验。     

AP1000核电厂模型基底隔震振动台试验研究

为研究AP1000核电厂基底隔震性能,设计了缩尺比为1/40的AP1000核电厂模型结构,进行了AP1000核电厂模型基底隔震振动台试验。试验中采用铅芯橡胶隔震支座进行隔震,并选取RG1.60人工波、El Centro波和Kobe波作为地震动输入。本文从加速度响应、楼层加速度反应谱、加速度峰值放大系数、减震率等方面对隔震与非隔震核电厂结构的地震响应特性进行了研究。试验结果表明:隔震能明显减小上部结构水平向加速度响应和加速度反应谱峰值,而在隔震频率处隔震模型加速度反应谱有所增加;隔震模型由于摇摆效应在隔震频率处的水平向楼层加速度反应谱随楼层高度的升高先减小后增大;在三向输入地震动作用下,隔震和非隔震AP1000模型各楼层在竖向基频附近的竖向加速度反应谱较竖向输入的地震动放大较为明显。     

地震模拟振动台试验系统频率特性估计的研究及应用

系统地分析了在地震模拟振动台试验系统频率特性测试过程中，测量误差，环境对振动台驱动信号的干扰噪声及试验系统本身非线性等因素的影响，得到了对指导试验具有重要意义的结论，阐述了应用试验系统频率特性对试验进行数字补偿控制的方法，并列举一些实例。     

基于振动台试验的黄土场地效应研究

地震作用下黄土场地对地震波不同分量的放大效应影响显著。针对黄土高原典型黄土场地在地震作用下的放大效应,设计并完成大型地震模拟振动台试验,通过输入不同强度的地震动荷载,研究黄土场地加速度（PGA）放大系数、傅里叶谱、加速度反应谱、H/V谱比与地震动强度和场地高度的变化规律,揭示地震波不同分量对黄土场地效应的影响。结果显示：黄土场地对地震波的水平分量具有明显的放大效应,对地震波垂直分量的放大效应影响较小;随着高程的增加,地震波水平分量PGA放大系数呈现非线性变化;随着地震动强度和高程的增加水平分量卓越频率的频段和幅值逐渐增加,卓越频率向低频偏移,放大倍数呈现出非线性特性。     

地震作用下隔震简支梁桥碰撞反应的振动台试验

由地震引发的碰撞是影响桥梁地震反应以及造成桥梁破坏的重要因素。本文对地震作用下隔震简支梁桥的碰撞反应进行了振动台试验。设计制作1个两跨简支的隔震梁桥模型,试验研究了梁间隙、邻梁质量比、隔震支座类型等参数对桥梁碰撞反应的影响。试验结果表明邻梁间隙、邻梁质量比、隔震支座类型等参数对桥梁的碰撞反应有着显著的影响。邻梁间隙越大,碰撞次数越少;邻梁质量比越大,撞击力越大。铅芯橡胶支座比板式橡胶支座耗能能力更强,可以有效降低邻梁之间的撞击力甚至避免碰撞发生。从而为桥梁防碰撞设计提供了可靠的试验依据。     

燃气调压站地震安全控制装置参数的振动台试验

为了更好地确定城市燃气调压站管道上地震安全控制装置的参数,针对城市燃气调压站的管道开展了振动台地震响应定量研究.以河北省唐山市某小区装有地震安全控制装置的调压站管道为实验对象,建立了振动台分析模型,选取了不同频谱特性的地震动,并获得了不同地震加速度输入工况下燃气调压站内地震安全控制装置的安装点及其他位置的加速度时程、频...     

核电站设备的振动台试验

本文进行了核电站设备（IS型单级单吸清水离心泵）的动力特性测试和振动台试验，使用自由振动衰减法、白噪声激振法和半功率点法分别测出了水泵在三个方向上的自振频率和阻尼比。给出了楼板加速度时程的模拟方法。根据本文给出的模拟方法和楼板反应谱，模拟了楼板加速度时程，并进行了水泵的振动台试验。振动台试验是在水泵工作状态下进行的。     

High-fidelity control of a seismic shake table

A high-fidelity PC-based control system has been developed to improve the tracking characteristics of a small-scale seismic motion simulator used for testing structural control designs. This work outlines the development and testing of the control system. First, the simulator hardware is described in detail. The process of constructing a mechanistic model of the system and identifying model parameters is then described. Next, a closed-loop feedback/feed-forward control algorithm, based on an optimal receding horizon formulation, is developed. The control design was tested and the results indicate that the seismic shake table precisely tracked reference seismic motions. Copyright © 1999 John Wiley & Sons, Ltd.     

Experimental assessment of the seismic performance of hospital cabinets using shake table testing

An experimental investigation of hospital building equipment is presented. Dynamic properties and seismic performance of typical ambulatory freestanding cabinets are assessed by unidirectional and bidirectional shake table tests, also considering the presence of internal partitions and cabinet contents. Vulnerability analysis is performed according to the most recent and reliable assessment methods, evaluating the influence of different parameters of the sample cabinets. The performance criteria referred within this research are the limit states reached by the specimens (ie, rocking and overturning) and by their contents (ie, overturning and breaking). Fragility curves are evaluated for the components and the contents, considering both acceleration and velocity intensity measures, and also using dimensionless intensity measures developed in recent studies. The outcomes of the present study confirm the findings of previous laboratory tests and numerical simulations carried out by the same authors and provide a further insight for the reliable seismic performance assessment of hospital cabinets and their contents.     

基于HHT的结构强震记录分析研究

本文利用HHT(Hilbert-HUang Transform)研究了结构强震记录的时频特性及结构动力特性。介绍了一座7层钢混框架结构及其强震观测台阵概况以及经历的地震情况,选择了在3次有代表性地震中的强震记录,利用一种新的非平稳信号处理方法HHT对记录进行了处理和分析,得到了该结构强震记录的时频幅值三维分布以及边际谱,并将边际谱与傅里叶谱进行了对比,识别了结构的自振频率。研究表明,对结构强震记录这种强非平稳信号,可以利用HHT分析得到能量集中分布的频段与时间范围。HHT边际谱与傅里叶谱相比,在低频部分幅值要大于傅里叶谱,而在高频部分,幅值要小于傅里叶谱。利用结构强震记录识别的自振频率比环境振动测试结果要小。     

低频振动台主要性能指标测试分析

为了更好满足地震计的振动测试需求,对振动台的波形失真度、横向运动比、台面不均匀度及稳定性等主要性能指标进行了测试分析.测试结果表明:该振动台具有较好的低频振动特性.利用低频标准套组对该振动台和中国计量科学研究院标准振动台进行比对分析,测试结果存在较小偏差.     

Simulation of floor response spectra in shake table experiments

Among several different experimental techniques, used to test the response of structures and to verify their seismic performance, the shake table testing allows to reproduce the conditions of true effects of earthquake ground motions in order to challenge complex model structures and systems. However, the reproduction of dynamic signals, due to the dynamics of the shake table and of the specimen, is usually imperfect even though closed‐loop control in a shake table system is used to reduce these errors and obtain the best fidelity reproduction. Furthermore, because of the dynamic amplifications in the specimen, the signal recorded at desired locations could be completely different from the expected effect of shake table motion. This paper focuses on the development of practical shake table simulations using additional ‘open loop’ feedforward compensation in form of inverse transfer functions (i.e. the ratio of the output structural response to an input base motion in the frequency domain) in order to obtain an acceptable reproduction of desired acceleration histories at specific locations in the specimen. As the first step, a well‐known global feedforward procedure is reformulated for the compensation of the table motion distortions due to the servo‐hydraulic system. Subsequently, the same concept is extended to the table‐structure system to adjust the shake table input in order to achieve a desired response spectrum at any floor of the specimen. Implementations show how such a method can be used in any experimental facility. Copyright © 2010 John Wiley & Sons, Ltd.     

HHT方法在地电场数据处理中的应用

较为详细地介绍了一种新的非线性、非平稳信号的处理方法—HHT（Hilbert-Huang Transform）方法,阐述了该方法的创新性,并对其有效性进行了数值检验.把该方法应用于新疆和田地电场台站和陕西西安地电场台站的观测数据,得到了各自的经验模态分解图、HHT时频图和相应的边际谱图,从这些图中可以清楚看出各自的频谱特征.最后阐述了HHT方法在地电场数据处理中的应用前景.     

混合结构振动台模型试验研究与计算分析

为研究混合结构的整体抗震性能,本研究以一个Ⅷ度区的LG大厦为原型,制作了1／20的整体模型,在同济大学土木工程国家重点实验室进行振动台试验,以考察地震动频谱及地震强度对混合结构地震反应的影响,了解混合结构体系的抗震性能、地震反应和破坏特征．本文还利用纤维模型建模对混合结构整体抗震性进行了非线性分析计算,并将计算结果与振动台试验数据进行对比分析,试验和计算结果表明：外钢骨框架-内混凝土核心筒混合结构具有较好的抗震性能．     

轮辐式大跨度张拉结构地震反应分析

以世纪莲体育中心大跨度轮辐式张拉索膜结构为研究对象,利用有限元程序ANSYS,分别采用振型分解反应谱法和时程分析方法,计算地震作用下结构的受力性能。研究表明:结构以索膜屋盖竖向振动为主,上压环、下压环及腹杆等均参与了振动,动力特性复杂;地震作用下结构内力和位移较大,不同方向地震作用的危害主次不明显,应同时考虑一维及多维地震组合作用的影响;2种计算方法下,结构的内力和位移变化趋势基本一致,为全面了解结构的动力特性,建议采用时程分析方法。     

Shake table testing of a multi-tower connected hybrid structure

Many single-tower reinforced concrete core wall-steel frame (RCC-SF) buildings have been built in China, but there are no buildings of different-height multi-tower hybrid system. A multi-tower RCC-SF tall building was thus studied because of its structural complexity and irregularity. First, a 1/15 scaled model structure was designed and tested on the shake table under minor, moderate, and major earthquake levels. Then, the dynamic responses of the model structure were interpreted to those of the prototype structure according to the similitude theory. Experimental results demonstrate that, despite the complexity of the structure, the lateral deformation bends as the "bending type" and the RC core walls contribute more than the steel frames to resist seismic loads. The maximum inter-story drift of the complex building under minor earthquakes is slightly beyond the elastic limitation specified in the Chinese code, and meets code requirements under major earthquakes. From the test results some suggestions are provided that could contribute favorable effect on the seismic behavior and the displacement of the building.     

Experimental characterization,modeling and identification of the NEES‐UCSD shake table mechanical system

This paper proposes a simple conceptual mathematical model for the mechanical components of the NEES‐UCSD large high‐performance outdoor shaking table and focuses on the identification of the parameters of the model by using an extensive set of experimental data. An identification approach based on the measured hysteresis response is used to determine the fundamental model parameters including the effective horizontal mass, effective horizontal stiffness of the table, and the coefficients of the classical Coulomb friction and viscous damping elements representing the various dissipative forces in the system. The effectiveness of the proposed conceptual model is verified through a comparison of analytical predictions with experimental results for various tests conducted on the system. The resulting mathematical model will be used in future studies to model the mechanical components of the shake table in a comprehensive physics‐based model of the entire mechanical, hydraulic, and electronic system. Copyright © 2007 John Wiley & Sons, Ltd.