Bed load transport on the shoreface by currents and waves

Tide-driven bed load transport is an important portion of the net annual sediment transport rate in many shoreface and shelf environments. However, bed load transport under waves cannot be measured in the field and bed load transport by currents without waves is barely measurable, even in spring tidal conditions. There is, consequently, a strong lack of field data and validated models. The present field site was on the shoreface and inner shelf at 2 to 8.5 km offshore the central Dutch coast (far outside the surfzone), where tidal currents flow parallel to the coast. Bed load transports were carefully measured with a calibrated sampler in spring tidal conditions without waves at a water depth of 13–18 m with fine and medium sands. The near-bed flow was measured over nearly a year and used for integration to annual transport rates. An empirical bed load model was derived, which predicts bed load transports that are a factor of > 5 smaller than predicted by existing models. However, they agree with laboratory data of sand and gravel transport in currents near incipient motion. The damped transport rates may have been caused by cohesion of sediment or turbulence damping due to mud or biological activity. The annual bed load transport rate was calculated using a probability density function (pdf) derived from the near-bed current and orbital velocity data which represented the current and wave climate well when compared to 30 years of data from a nearby wave station. The effect of wave stirring was included in the transport calculations. The net bed load transport rate is a few m²/year. This is much less than predicted in an earlier model study, which is partly due to different bed load models but also due to the difference in velocity pdf. The annual transport rate is very sensitive to the probability of the largest current velocities.     

Investigation of Π-type breakwaters performance under regular and irregular waves

In this paper, performance of solid and perforated Π-type breakwaters was investigated experimentally. Both regular and irregular waves were used during testing. Four depths of immersions were selected for each breakwater and wave type. Different wave groups were generated over these breakwaters, and the transmission, reflection and energy-dissipation characteristics were determined. The results of the experimental study were evaluated and some empirical expressions based on the results were suggested to define the transmission, reflection and energy-dissipation coefficients for different immersion depths of solid and perforated breakwaters under regular and irregular waves. Moreover, performance of solid and perforated Π-type breakwaters were compared with that of solid and perforated U-type breakwaters investigated by Günaydın and Kabdaşlı [2006. Performance of solid and perforated U-type breakwaters under regular and irregular waves. Ocean Engineering 31, 1377–1405]. These comparisons showed that the most reasonable model and wave type are selected to determine requiring performance parameters.     

A probability distribution for depth-limited extreme wave heights in a sea state

A model for the depth-limited distribution of the highest wave in a sea state is presented. The distribution for the extreme wave height is based on a probability density function (pdf) for depth-limited wave height distribution for individual waves [Méndez, F.J., Losada, I.J., Medina, R. 2004. Transformation model of wave height distribution. Coastal Eng, Vol. 50, 97:115.] and considers the correlation between consecutive waves. The model is validated using field data showing a good representation of the extreme wave heights in the surf zone. Some important statistical wave heights are parameterized obtaining useful expressions that can be used in further calculations.     

Parameter identification of a compliant nonlinear SDOF system in random ocean waves by reverse MISO method

The determination of the drag and inertia coefficients, which enter into the wave force model given by Morison's equation, is particularly uncertain and difficult when a linear spectral model is used for ocean waves, and the structure is compliant and has nonlinear dynamic response. In this paper, a nonlinear System Identification method, called Reverse Multiple Inputs–Single Output (R–MISO) is applied to identify the hydrodynamic coefficients as well as the nonlinear stiffness parameter for a compliant single-degree-of-freedom system. Four different types of problems have been identified for use in various situations and the R–MISO has been applied to all of them. One of the problems requires iterative solution strategy to identify the parameters. The method has been found to be efficient in predicting the parameters with reasonable accuracy and has the potential for use in the laboratory experiments on compliant nonlinear offshore systems.     

Numerical Modeling of a Round Jet Discharged into Random Waves

Coastal disposal of waste water can be idealized as the problem of a jet under random waves. Understanding of this phenomenon is important for engineering design and environmental impact assessment. The present study aims to simulate such phenomenon by using a 3D numerical model based on the solution of the spatially filtered and σ-transformed Navier–Stokes equations with dynamic sub-grid scale model of turbulence. The numerical solution procedures are split into three steps: advection, diffusion and pressure propagation, and a Lagrange–Euler method is used to track the free surface. Cases of vertical jet in stagnant water, pure random waves and vertical jet in random waves are simulated with the same grid system for comparative study. Different methods of generating jet inflow turbulence have been tested and the method of jet azimuthal modes is found to be the optimum. The numerical results reproduce the distinct characteristics of jet in waves, including faster decay of centerline velocity, wider lateral spreading and the occurrence of wave tractive mechanism.     

Design of passive anti-roll tanks for roll stabilization in the nonlinear range

The best way of reducing roll motion is by increasing roll damping. Bilge keels are the most common devices for increasing roll damping. If more control is required, anti-roll tanks and fins are used. Tanks have the advantage of being able to function when the ship is not underway. Our objective is to develop design procedures for passive tanks for roll reduction in rough seas. This paper focuses on the design of passive U-tube tanks. The tank-liquid equation of motion is integrated simultaneously with the six-degree-of-freedom (6DOF) equations of the ship motion. The coupled set of equations is solved by using the Large Amplitude Motion Program ‘LAMP’, which is a three-dimensional time-domain simulation of the motion of ships in waves. The unstabilized and stabilized roll motions of a S60-70 ship with forward speed and beam waves have been analyzed. For high-amplitude waves, the unstabilized roll angle exhibits typical nonlinear phenomena: a shift in the resonance frequency, multi-valued responses, and jumps. The performance of a S60-70 ship with a passive tank is investigated in various sea states with different encounter wave directions. It is found that passive anti-roll tanks tuned in the linear or nonlinear ranges are very effective in reducing the roll motion in the nonlinear range. The effect of the tank damping, frequency, and mass on the tank performance is studied. Also, it is found that passive anti-roll tanks are very effective in reducing the roll motion for ships having a pitch frequency that is nearly twice the roll frequency in sea states 5 and 6.     

Seakeeping performance of a containment boom section in random waves and currents

The seakeeping characteristics of various boom geometries in irregular waves and currents are investigated. The response of a floating boom section on the open sea is a function of a number of parameters, such as boom geometry, distribution of mass, buoyancy/weight ratio, and wave and current characteristics. To understand the relationship between these design parameters more clearly, a series of regular and irregular wave tests were conducted with six different 1:4 scale models for three current velocities and six different wave conditions. To simplify the problem, only rigid boom sections consisting of a buoyancy cylinder and vertical skirt were used. In parallel with this experimental program, a numerical model for the responses of two-dimensional floating boom sections in small-amplitude waves is also developed. The numerical results are compared with our large-scale experimental results. The boom effectiveness on the open sea is evaluated based on the concept of “effective draft” and “effective freeboard” assuming that drainage and oversplashing failures are the prime mechanisms of containment failure. Using the present results, a guideline for the optimum design/selection of future booms is developed.     

Multidirectional wave transformation around detached breakwaters

The performance of the new wave diffraction feature of the shallow-water spectral model SWAN, particularly its ability to predict the multidirectional wave transformation around shore-parallel emerged breakwaters is examined using laboratory and field data. Comparison between model predictions and field measurements of directional spectra was used to identify the importance of various wave transformation processes in the evolution of the directional wave field. First, the model was evaluated against laboratory measurements of diffracted multidirectional waves around a breakwater shoulder. Excellent agreement between the model predictions and measurements was found for broad frequency and directional spectra. The performance of the model worsened with decreasing frequency and directional spread. Next, the performance of the model with regard to diffraction–refraction was assessed for directional wave spectra around detached breakwaters. Seven different field cases were considered: three wind–sea spectra with broad frequency and directional distributions, each coming from a different direction; two swell–sea bimodal spectra; and two swell spectra with narrow frequency and directional distributions. The new diffraction functionality in SWAN improved the prediction of wave heights around shore-parallel breakwaters. Processes such as beach reflection and wave transmission through breakwaters seem to have a significant role on transformation of swell waves behind the breakwaters. Bottom friction and wave–current interactions were less important, while the difference in frequency and directional distribution might be associated with seiching.     

Wave reflection characteristics of plane, dentated and serrated seawalls

The hydrodynamic performance of vertical and sloped plane, dentated and serrated seawalls were investigated using physical model studies. Regular and random waves of wide range of heights and periods were used. Tests were carried out for different inclinations of the seawall (i.e. θ=30, 40, 50, 60 and 90°) and for a constant water depth of 0.7 m. The wave reflection was measured to assess the dissipation character of the seawalls. It was observed that the serrated seawall was superior to the plane and dentated seawall in reducing the wave reflection. Even for the vertical case, the coefficient of reflection due to regular waves for dentated seawall ranged from 0.6–0.99 and for the vertical serrated seawall it was 0.45–0.98, whereas for the vertical plane wall, it was almost 1.0. It was found that the characteristic dimension of the seawall (i.e. L/W) and the relative water depth (i.e. d/L) were better influencing parameters compared to the conventionally used surf similarity parameter ‘ξ’ (ξ=tan θ/(H_i/L)^0.5) in predicting the reflection from the dentated and serrated seawall, where L is the local wave length, W the width of the dent along the length of the seawall slope, d the water depth at the toe and H_i is the incident wave height. A similar trend was observed for the random waves too. The reduction in the wave reflection due to random waves for the dentated seawall as compared to the plane seawall was about 18% and for the serrated seawall, it was 20%. It was observed that the reflection due to random waves was lesser for all the three different walls than the regular waves, due to the mutual interaction of random waves. Multiple regression analysis on the measured data points was carried out and predictive equations for the reflection coefficient were obtained for both regular and random waves. This study will be useful in the design of energy dissipating type vertical quay walls in ports and harbours, sloped seawalls for shore protection from erosion and sloped caisson as breakwaters. Comparison of predictive formulae with the experimental results revealed that the prediction methods were good enough for practical purposes.     

Static stability of submerged partial revetment structures under regular and irregular waves

Physical models of submerged partial revetment structures were built on natural beach sand with a diameter of 0.35 mm and specific gravity of 2.63. The armor units, the diameter and specific gravity of which varied in the range of 8.5–67.95 mm and 1.81–2.77 respectively, were placed only on wave breaking areas. A series of experiments has been conducted on the conditions of different armor units and different wave characteristics using regular waves and irregular waves. Based on the experimental data, the effects of wave height, wave period, diameter and specific gravity of armor units, water depth in the channel, and wave types on static damage of given structures are assessed. Some empirical formulas have been suggested through regression analysis to describe static stability and stability number of submerged partial revetment structures under pure regular waves, pure irregular waves, and regular–irregular waves. The suggested formulas compared with Van der Meer’s (1988) formulas and some differences have occurred because of differences among revetment types and test conditions; therefore, proposed formulas give reasonable results for the test conditions used.     

Probability distributions for maximum wave and crest heights

The paper discusses short- and long-term probability models of ocean waves. The Gaussian theory is reviewed, and nonlinear short-term probability distributions are derived from a narrow band second-order model. The nonlinearity has different impact on different measurement techniques, and this is further demonstrated for wave data from the WAVEMOD Crete measurement campaign and laser data from the North Sea. Finally, we give some examples on how the short-term statistics may be used to estimate the probability distributions for the maximum waves during individual storms as well as in a wave climate described by long-term distributions.     

Variations in the Baltic Sea wave fields

The surface waves in the Baltic Sea are hindcast with the spectral wave model HYPAS during a 12-month period. The model results show a strong temporal and spatial variation in the wave field due to the physical dimensions of the different basins and the predominant wind field. The highest waves in the area are found in the outer part of Skagerrak, as well as in the central and southern parts of the Baltic Proper. To get significant waves above 6 m high, strong winds (15–20 m/s) must have been blowing for 6 to 24 h from a favourable direction over a deep area.     

Characteristics of turbulent boundary layers over a rough bed under saw-tooth waves and its application to sediment transport

A large number of studies have been done dealing with sinusoidal wave boundary layers in the past. However, ocean waves often have a strong asymmetric shape especially in shallow water, and net of sediment movement occurs. It is envisaged that bottom shear stress and sediment transport behaviors influenced by the effect of asymmetry are different from those in sinusoidal waves. Characteristics of the turbulent boundary layer under breaking waves (saw-tooth) are investigated and described through both laboratory and numerical experiments. A new calculation method for bottom shear stress based on velocity and acceleration terms, theoretical phase difference, φ and the acceleration coefficient, a_c expressing the wave skew-ness effect for saw-tooth waves is proposed. The acceleration coefficient was determined empirically from both experimental and baseline k–ω model results. The new calculation has shown better agreement with the experimental data along a wave cycle for all saw-tooth wave cases compared by other existing methods. It was further applied into sediment transport rate calculation induced by skew waves. Sediment transport rate was formulated by using the existing sheet flow sediment transport rate data under skew waves by Watanabe and Sato [Watanabe, A. and Sato, S., 2004. A sheet-flow transport rate formula for asymmetric, forward-leaning waves and currents. Proc. of 29th ICCE, ASCE, pp. 1703–1714.]. Moreover, the characteristics of the net sediment transport were also examined and a good agreement between the proposed method and experimental data has been found.     

An experimental study on non-linear progressive wave-induced dynamic stresses in seabed

In this study, the dynamic stresses within the seabed induced by non-linear progressive waves were explored through a series of hydraulic model tests on a movable bed within a wave flume. By comparing Stokes’ 2nd-order wave theory with the theory of wave-induced dynamic stresses within the seabed as proposed by Yamamoto et al. [1978. On the response of a poro-elastic bed to water waves. Journal of Fluid Mechanics 87 (1), 193–206.] and Hsu and Jeng [1994. Wane-induced soil response in an unsaturated anisotropic seabed of finite thickness. International Journal for Numerical and Analytical Methods in Geomechanics 18, 785–807], the experimental results show that the pressure on the seabed surface, the pore water pressure within the seabed as well as the vertical and the horizontal stresses are all smaller than their theoretical values. If we were to obtain the characteristics of seabed soil, the analytical solution of Hsu and Jeng [1994. Wane-induced soil response in an unsaturated anisotropic seabed of finite thickness. International Journal for Numerical and Analytical Methods in Geomechanics 18, 785–807] might agree to the simulation of the wave-induced effective stresses and shear stress in the sandy seabed. A different phase shift exists among all the three soil stresses. Their influences on the three dynamic stresses within seabed soil are important for seabed stability, and can be used in the verification of numerical models. In the whole, the non-linear progressive waves and the naturally deposited seabed are found to have a strong interaction, and the behavior of the induced dynamic stresses within the seabed is very complicated, and should be investigated integrally.     

An elastic–viscous–plastic sea ice model formulated on Arakawa B and C grids

The elastic–viscous–plastic (EVP) sea ice rheology has been introduced in the large-scale Louvain-la-Neuve sea-Ice Model, version 2 (LIM2), and its performance has been evaluated. Centred difference versions of the rheology have been implemented on both an Arakawa B grid and a C grid, and their performance have been intercompared in coupled simulations with the Nucleus for European Modelling of the Ocean (NEMO) model. Integrations with both implementations lead to fairly similar results which compare well with observations and with previous LIM simulations. The C grid version, however, offers a number of advantages: (a) easier ice coupling with NEMO, which is itself defined on a C grid; (b) possibility of representing ice transport across one-cell-wide straits and passages; (c) better representation of inertial-plastic compressive waves. For these reasons, we recommend the use of the C grid EVP formulation of the ice dynamics in future LIM applications.     

The stability of the antifer units used on breakwaters in case of irregular placement

The primary aim of the study is to experimentally investigate the stability performance of antifer units on the trunk section of breakwaters under the effect of regular and irregular waves in case of irregular placement. The stability performance tests were conducted for different slopes, i.e. cot α=1.25, 1.5, 2.0, 2.5, under irregular waves and for cot α=2.5 under regular waves. Hudson’s formula was employed in order to characterize the stability performance of antifer units for the irregular placement technique. Different representative wave height parameters, i.e. H_s, H_1/10 and H_max, were examined to determine the one best characterizing breakwater stability. Furthermore, the effects of wave period and wave steepness on the stability of the breakwater were explored.     

A Physically Consistent Speckle Model for Marine SLC SAR Images

A new physically based speckle model for marine single-look complex (SLC) synthetic aperture radar (SAR) images is here presented and investigated. The model allows using full-resolution SAR images instead of multilook SAR images, in which, at the expense of a coarser spatial resolution, the speckle is mitigated. The model is based on the three-parameters generalized-K (GK) probability density function (pdf). GK pdf is a suitable physically-based speckle model for marine SAR images ensuring a continuous and physically consistent transition among different scattering scenarios. This speckle model embodies Rayleigh, K, and Rice scattering scenes which are typical of marine scenes. The use of the three parameters, related to the GK pdf ones, is able to highlight the presence of both low backscattering areas and areas in which a small dominant scatterer is present. This is operationally interesting in SAR oil spill detection procedures.     

Wave propagation in a fully nonlinear numerical wave tank: A desingularized method

The problem of wave propagation in a fully nonlinear numerical wave tank is studied using desingularized boundary integral equation method coupled with mixed Eulerian–Lagrangian formulation. The present method is employed to solve the potential flow boundary value problem at each time step. The fourth-order predictor–corrector Adams–Bashforth–Moulton scheme is used for the time-stepping integration of the free surface boundary conditions. A damping layer near the end-wall of wave tank is added to absorb the outgoing waves with as little wave reflection back into the wave tank as possible. The saw-tooth instability is overcome via a five-point Chebyshev smoothing scheme. The model is applied to several wave propagations including solitary, irregular and random incident waves.     

Wave reflection from partially perforated-wall caisson breakwater

In 1995, Suh and Park developed a numerical model that computes the reflection of regular waves from a fully perforated-wall caisson breakwater. This paper describes how to apply this model to a partially perforated-wall caisson and irregular waves. To examine the performance of the model, existing experimental data are used for regular waves, while a laboratory experiment is conducted in this study for irregular waves. The numerical model based on a linear wave theory tends to over-predict the reflection coefficient of regular waves as the wave nonlinearity increases, but such an over-prediction is not observed in the case of irregular waves. For both regular and irregular waves, the numerical model slightly over- and under-predicts the reflection coefficients at larger and smaller values, respectively, because the model neglects the evanescent waves near the breakwater.