A New Method for the Determination of Area-Averaged Turbulent Surface Fluxes from Low-Level Flights Using Inverse Models

The low-level flight method (LLF) has been combined with linear inverse models (IM) resulting in an LLF+IM method for the determination of area-averaged turbulent surface fluxes. With this combination, the vertical divergences of the turbulent latent and sensible heat fluxes were calculated from horizontal flights. The statistical errors of the derived turbulent surface fluxes were significantly reduced. The LLF+IM method was tested both in numerical and field experiments. Large-eddy simulations (LES) were performed to compare ‘true’ flux profiles with ‘measurements’ of simulated flights in an idealised convective boundary layer. Small differences between the ‘true’ and the ‘measured’ fluxes were found, but the vertical flux divergences were correctly calculated by the LLF+IM method. The LLF+IM method was then applied to data collected during two flights with the Helipod, a turbulence probe carried by a helicopter, and with the research aircraft Do 128 in the LITFASS-98 field campaign. The derived surface fluxes were compared with results from eddy-covariance surface stations and with large-aperture scintillometer data. The comparison showed that the LLF+IM method worked well for the sensible heat flux at 77 and 200 m flight levels, and also for the latent heat flux at the lowest level. The model quality control indicated failures for the latent heat flux at the 200 m level (and higher), which were probably due to large moisture fluctuations that could not be modelled using linear assumptions. Finally the LLF+IM method was applied to more than twenty low-level flights from the LITFASS-2003 experiment. Comparison with aggregated surface flux data revealed good agreement for the sensible heat flux but larger discrepancies and a higher statistical uncertainty for the latent heat flux     

Spectral Structure of Small-Scale Turbulent and Mesoscale Fluxes in the Atmospheric Boundary Layer over a Thermally Inhomogeneous Land Surface

Spectral analysis was performed on aircraft observations of a convective boundary layer (CBL) that developed over a thermally inhomogeneous, well-marked mesoscale land surface. The observations, part of the GAME-Siberia experiment, were recorded between April and June 2000 over the Lena River near Yakutsk City. A special integral parameter termed the ‘reduced depth of the CBL’ was used to scale the height of the mixed layer with variable depth. Analysis of wavelet cospectra and spectra facilitated the separation of fluxes and other variables into small-scale turbulent fluctuations (with scales less than the reduced depth of the CBL, approximately 2 km) and mesoscale fluctuations (up to 20 km). This separation approach allows for independent exploration of the scales. Analyses showed that vertical distributions obeyed different laws for small-scale fluxes and mesoscale fluxes (of sensible heat, water vapour, momentum and carbon dioxide) and for other variables (wind speed and air temperature fluctuations, coherence and degree of anisotropy). Vertical profiles of small-scale turbulent fluxes showed a strong decay that differed from generally accepted similarity models for the CBL. Vertical profiles of mesoscale fluxes and other variables clearly showed sharp inflections at the same relative (with respect to the reduced depth of the CBL) height of approximately 0.55 in the CBL. Conventional similarity models for sensible heat fluxes describe both small-scale turbulent and mesoscale flows. The present results suggest that mesoscale motions that reach up to the relative level of 0.55 could be initiated by thermal surface heterogeneity. Entrainment between the upper part of the CBL and the free atmosphere may cause mesoscale motions in that region of the CBL.     

Validation of the “Lokal-Modell” over heterogeneous land surfaces using aircraft-based measurements of the REEEFA experiment and comparison with micro-scale simulations

Summary An aircraft-based experimental investigation of the atmospheric boundary layer (ABL) structure and of the energy exchange processes over heterogeneous land surfaces is presented. The measurements are used for the validation of the mesoscale atmospheric model “Lokal-Modell” (LM) of the German Weather Service with 2.8 km resolution. In addition, high-resolution simulations using the non-hydrostatic model FOOT3DK with 250 m resolution are performed in order to resolve detailed surface heterogeneities. Two special observation periods in May 1999 show comparable convective boundary layer (CBL) conditions. For one case study vertical profiles and area averages of meteorological quantities and energy fluxes are investigated in detail. The measured net radiation is highly dependent on surface albedo, and the latent heat flux exhibits a strong temporal variability in the investigation area. A reduction of this variability is possible by aggregation of multiple flight patterns. To calculate surface fluxes from aircraft measurements at low altitude, turbulent energy fluxes were extrapolated to the ground by the budget method, which turned out to be well applicable for the sensible heat flux, but not for the latent flux. The development of the ABL is well captured by the LM simulation. The comparison of spatiotemporal averages shows an underestimation of the observed net radiation, which is mainly caused by thin low-level clouds in the LM compared to observed scattered CBL clouds. The sensible heat flux is reproduced very well, while the latent flux is highly overestimated especially above forests. The realistic representation of surface heterogeneities in the investigation area in the FOOT3DK simulations leads to improvements for the energy fluxes, but an overestimation of the latent heat flux still persists. A study of upscaling effects yields more structures than the LM fields when averaged to the same scale, which are partly caused by the non-linear effects of parameter aggregation on the LM scale.     

Airborne measurements of turbulent fluxes during LITFASS-98: Comparison with ground measurements and remote sensing in a case study

Summary ?Simultaneous flight measurements with the research aircraft Do 128 and the helicopter-borne turbulence probe Helipod were performed on 18 June 1998 during the LITFASS-98 field experiment. The area-averaged turbulent vertical fluxes of momentum, sensible, and latent heat were determined on a 15 km × 15 km and a 10 km × 10 km flight pattern, respectively. The flights were carried out over heterogeneous terrain at different altitudes within a moderately convective boundary layer with Cumulus clouds. Co-spectra-analysis demonstrated that the small scale turbulent transport was completely sampled, while the comparatively small flight patterns were possibly of critical size regarding the large-scale turbulence. The phygoide of the airplane was identified as a significant peak in some co-spectra. The turbulent fluxes of momentum and sensible heat at 80 m above the ground showed systematic dependence on the location of the flight legs above the heterogeneous terrain. This was not observed for the latent heat flux, probably due to the vertical distribution of humidity in the boundary layer. Statistical error analysis of the fluxes F showed that the systematic statistical error ΔF was one order of magnitude smaller than the standard deviation σ _F . The difference between area-averaged fluxes derived from simultaneous Helipod and Do 128 measurements was much smaller than σ _F , indicating that the systematic statistical error was possibly over-estimated by the usual method. In the upper half of the boundary layer the airborne-measured sensible heat flux agreed well with windprofiler/RASS data. A linear fit was the best approximation for the height dependence of all three fluxes. The linear extrapolations of the latent and sensible heat fluxes to the ground were in good agreement with tower, scintillometer, and averaged ground-station measurements on various surface types. Systematic discrepancies between airborne and ground-based measurements were not found. Received June 18, 2001; revised December 21, 2001; accepted June 3, 2002     

Creating Surface Flux Maps from Airborne Measurements: Application to the Mackenzie Area GEWEX Study MAGS 1999

The objective of this study is to produce two-dimensional maps of the sensible and the latent heat fluxes from airborne measurements, based on the analysis of a flight pattern, called grid flights. A footprint model with along-wind and cross-wind components was used to project the measured fluxes onto the surface map. The method was applied to measurements over Arctic tundra during the Mackenzie Area GEWEX (Global Energy and Water Cycle Experiment) Study (MAGS) 1999. The resulting flux estimates were computed by integration of a wavelet transform, and corrected for long wavelength losses using information from 100 km long regional runs that were conducted close to the grid flights. The random flux error was estimated based on the flight length that is represented in each map element, and a map resolution of 3 × 3 km was chosen in order to keep the average random error of the latent heat flux below 25%. The random error of the sensible heat flux was smaller by a factor of 1.4 on average. An analysis of airborne flux measurements at different altitudes showed no significant increase of flux estimates for measurement heights below 90 m. Thus, the fluxes measured at heights between 48 and 64 m were not corrected for vertical flux divergence. The resulting flux maps provide quantitative two-dimensional estimates of the energy exchange between the surface and the atmosphere during the snow melt period in an Arctic environment, which are well-suited for calibration and validation of numerical models.     

Heterogeneity-Induced Heat-Flux Patterns in the Convective Boundary Layer: Can they be Detected from Observations and is There a Blending Height?—A Large-Eddy Simulation Study for the LITFASS-2003 Experiment

An understanding of how the convective boundary layer (CBL) is mixed under heterogeneous surface forcing is crucial for the interpretation of area-averaged turbulence measurements. To determine the height and degree to which a complex heterogeneous surface affects the CBL, large-eddy simulations (LES) for two days of the LITFASS-2003 experiment representing two different wind regimes were undertaken. Spatially-lagged correlation analysis revealed the turbulent heat fluxes to be dependent on the prescribed surface flux pattern throughout the entire CBL including the entrainment layer. These findings prompted the question of whether signals induced by surface heterogeneity can be measured by airborne systems. To examine this question, an ensemble of virtual flights was conducted using LES, according to Helipod flight measurements made during LITFASS-2003. The resulting ensemble-averaged heat fluxes indicated a clear dependence on the underlying surface up to the top of the CBL. However, a large scatter between the flux measurements in different ensemble runs was observed, which was the result of insufficient sampling of the largest turbulent eddies. The random and systematic errors based on the integral length scale did not indicate such a large scatter. For the given flight leg lengths, at least 10–15 statistically independent flight measurements were necessary to give a significant estimate of heterogeneity-induced signals in the CBL. The need for ensemble averaging suggests that the observed blending of heterogeneity-induced signals in the CBL can be partly attributed to insufficient averaging.     

Surface fluxes estimation over agricultural areas. Comparisonof methods and the effects of land surface inhomogeneity

Summary  The Bowen Ratio-Energy Balance (BREB) and the aerodynamic method were used to estimate turbulent fluxes of sensible and latent heat flux over an irrigated agricultural area (IAA) and over two dry agricultural areas (DAA1 and DAA2). These turbulent fluxes were analysed and particular attention paid to two specific areas. First, a quantitative analysis of sensible and latent heat fluxes obtained by the BREB method was carried out, taking into account different soil type, vegetation and surface conditions. The results showed that in IAA latent heat flux was higher than sensible heat flux, except in summer months, while in DAA1 and DAA2, sensible heat flux was higher except in the months when the vegetation was at the stage of maximum development. Second, sensible and latent heat fluxes estimates from the BREB method were compared with those obtained from the aerodynamic method. In this comparison factors such as soil type, soil vegetation cover, homogeneity or inhomogeneity of terrain and mesoscale effects such as orography and wind patterns were taken into account. The results show that in conditions of light wind, the two methods only concur if the condition of horizontal homogeniety is fulfilled. The influence of inhomogeneity seems to decrease and agreement between methods improves, if the wind is stronger and the effects of meso and synoptic scales are predominant. Received May 18, 1999/Revised March 15, 2000     

基于FLUXNET数据集对陆面模式CoLM能量通量的单点评估

模式评估是模式发展中的重要一环。本文利用来自FLUXNET2015数据集的30个站点的涡动相关系统观测数据,重点关注能量通量,对通用陆面模式（Common Land Model version 2014,CoLM2014）在不同典型下垫面的模拟能力进行评估。结果表明,模式总体上能抓住感热、潜热和净辐射通量在日、季节和年平均等不同时间尺度上的变化特征,对感热、潜热和净辐射通量都有较好的模拟能力,净辐射的模拟效果最好,潜热通量次之。季节变化模拟中,感热、潜热通量在夏季不同植被型下站点的空间离散程度大于冬季,不同站点间模拟效果相差较大,净辐射多站点标准差变化幅度要小于感热、潜热,不同站点间模拟效果偏差较小。CoLM在常绿针叶林、稀树林地、草地、农田模拟感热、潜热通量的效果相对较好,在永久湿地、落叶阔叶林下模拟感热通量较差。本研究对CoLM2014在未来的改进和发展中提供了有用的参考。     

Aircraft Observations of the Development of Thermal Internal Boundary Layers and Scaling of the Convective Boundary Layer Over Non-Homogeneous Land Surfaces

This study investigates the convective boundary layer (CBL) that develops over anon-homogeneous surface under different thermal and dynamic conditions. Analysesare based on data obtained from a Russian research aircraft equipped with turbulentsensors during the GAME-Siberia experiment over Yakutsk in Siberia, from April to June 2000.Mesoscale thermal internal boundary layers (MTIBLs) that radically modified CBLdevelopment were observed under unstable atmospheric conditions. It was found thatMTIBLs strongly influenced the vertical and horizontal structures of virtual potentialtemperature, specific humidity and, most notably, the vertical sensible and latent heatfluxes. MTIBLs in the vicinity of the Lena River lowlands were confirmed by clouddistributions in satellite pictures.MTIBLs spread through the entire CBL and radically modify its structure if the CBL isunstable, and strong thermal features on the underlying surface have horizontal scalesexceeding 10 km. MTIBL detection is facilitated through the use of special parameterslinking shear stress and convective motion.The turbulent structure of the CBL with and without MTIBLs was scaled usingthe mosaic or flux aggregate approach. A non-dimensional parameterL_Rau/L_hetero (where L_Rau is Raupach's length and L_hetero is the horizontal scale of the surface heterogeneity)estimates the application limit of similarity and local similarity scaling models forthe mosaic parts over the surface. Normalized vertical profiles of wind speed, airtemperature, turbulent sensible and latent heat fluxes for the mosaic parts withL_RauL_hetero < 1 could be estimated by typical scalingcurves for the homogeneous CBL. Traditional similarity scaling models for the CBLcould not be applied for the mosaic parts with L_Rau/L_hetero > 1.For some horizontally non-homogeneous CBLs, horizontal sensible heat fluxes werecomparable with the vertical fluxes. The largest horizontal sensible heat fluxes occurred at the top of the surface layer and below the top of the CBL.Formerly affiliated to the Frontier Observational Research System for Global ChangeFormerly affiliated to the Frontier Observational Research System for Global Change     

Further Development of the Vegetated Urban Canopy Model Including a Grass-Covered Surface Parametrization and Photosynthesis Effects

The vegetated urban canopy model (VUCM), which includes parametrizations of urban physical processes for artificial surfaces and vegetated areas in an integrated system, has been further developed by including physical processes associated with grass-covered surfaces in urban pervious surfaces and the photosynthesis effects of urban vegetation. Using measurements made from three urban/suburban sites during the BUBBLE field campaign in 2002, the model’s performance in modelling surface fluxes (momentum flux, net radiation, sensible and latent heat fluxes and storage heat flux) and canopy air conditions (canopy air temperature and specific humidity) was critically evaluated for the non-precipitation and the precipitation days. The observed surface fluxes at the urban/suburban sites were significantly altered by precipitation as well as urban vegetation. Especially, the storage heat at urban surfaces and underlying substrates varied drastically depending on weather conditions while having an important role in the formation of a nocturnal urban surface layer. Unlike the nighttime canopy air temperature that was largely affected by the storage-heat release, the daytime canopy air conditions were highly influenced by the vertical turbulent exchange with the overlying atmosphere. The VUCM well reproduced these observed features in surface fluxes and canopy air conditions at all sites while performing well for both the non-precipitation and the precipitation days. The newly implemented parametrizations clearly improved the model’s performance in the simulation of sensible and latent heat fluxes at the sites, more noticeably at the suburban site where the vegetated area fraction is the largest among the sites. Sensitivity analyses for model input parameters in VUCM elucidated the relative importance of the morphological, aerodynamic, hydrological and radiative/thermal properties in modelling urban surface fluxes and canopy air conditions for daytime and nighttime periods. These results suggest that the VUCM has great potential for urban atmospheric numerical modelling for a range of cities and weather conditions in addition to having a better physical basis in the representation of urban vegetated areas and associated physical processes.     

Key results and implications from phase 1(c) of the Project for Intercomparison of Land-surface Parametrization Schemes

 Using atmospheric forcing data generated from a general circulation climate model, sixteen land surface schemes participating in the Project for the Intercomparison of Land-surface Parametrization Schemes (PILPS) were run off-line to equilibrium using forcing data from a GCM representative of a tropical forest and a mid-latitude grassland grid point. The values for each land surface parameter (roughness length, minimum stomatal resistance, soil depth etc.) were provided. Results were quality controlled and analyzed, focusing on the scatter simulated amongst the models. There were large differences in how the models’ partitioned available energy between sensible and latent heat. Annually averaged, simulations for the tropical forest ranged by 79 1 3;W m^-2 for the sensible heat flux and 80 W m^-2 for the latent heat flux. For the grassland, simulations ranged by 34 W m^-2 for the sensible heat flux and 27 W m^-2 for the latent heat flux. Similarly large differences were found for simulated runoff and soil moisture and at the monthly time scale. The models’ simulation of annually averaged effective radiative temperature varied with a range, between all the models, of 1.4 K for tropical forest and 2.2 K for the grassland. The simulation of latent and sensible heat fluxes by a standard ‘bucket’ models was anomalous although this could be corrected by an additional resistance term. These results imply that the current land surface models do not agree on the land surface climate when the atmospheric forcing and surface parameters are prescribed. The nature of the experimental design, it being offline and with artificial forcing, generally precludes judgements concerning the relative quality of any specific model. Although these results were produced de-coupled from a host model, they do cast doubt on the reliability of land surface schemes. It is therefore a priority to resolve the disparity in the simulations, understand the reasons behind the scatter and to determine whether this lack of agreement in de-coupled tests is reproduced in coupled experiments. Received: 15 October 1997 / Accepted: 22 April 1999     

Regional-Scale Heat and Water Vapour Fluxes in an Agricultural Landscape: An Evaluation of CBL Budget Methods at OASIS

This paper evaluates convective boundary layer (CBL) budget methods as a tool for estimating regionally averaged sensible and latent heat fluxes for the study region used in OASIS (Observations at Several Interacting Scales). This is an agricultural region of mixed cropping and grazing extending about 100 km west of the town of Wagga Wagga, NSW, Australia.The analysis proceeds in three stages: first, a simpleone-dimensional model of the well-mixed layer (the CBL slab model), forced with measurements of the surface heat and evaporation fluxes, is evaluated by comparing measured and modelled CBL temperature, humidity and depths. A comparison of several entrainment schemes shows that a simple model, where the entrainment kinetic energy is parameterised as a fraction (₃) of the surface sensible heat flux, works well if is set to 0.5. Second, the slab model is coupled to a Penman–Monteith model of surface evaporation to predict regional scale evaporation and thence heat fluxes. Finally, the integral CBL budget approach, which is an inverse method using theone-dimensional slab model, is used to infer regional heat and evaporation fluxes from measured time series of CBL temperature and humidity.We find that the simple CBL slab model works reasonably well for predicting CBL depth and very well for CBL temperature, especially if approximate estimates of subsidence velocity and warming due to advection are included. Regional sensible heat fluxes estimated from the integral CBL method match those measured, although the method is very sensitive to measurement errors. Measurement-model differences were larger for short integration times, because the well-mixed assumptions are violated at particular times of the day. The corollary is that `whole-day' (0530–1530 h) estimates are in reasonable agreement with measured values. Integral methods could not be used to infer the regional evaporation flux directly because CBL humidity profiles were complex and often not well mixed until mid-afternoon. We recommend that regional evaporation fluxes be predicted either from a coupled Penman–Monteith – CBL slab model, or inferred as a residual term from estimates of the regionally averaged available energy and sensible heat flux. Furthermore, we show that inferring fluxes via integral methods will always be difficult when the scalar concentrations have either a large surface source and free atmosphere sink (in the case of water vapour and methane), or a large surface sink and upper level source (in the case of CO₂).     

Modelling sensible and latent heat fluxes over sea during unstable,very close to neutral conditions

During slightly unstable but still very close to neutral conditions new results from two previous investigations have shown a significant increase of sensible and latent heat fluxes over the sea. The vertical heat transport during these conditions is dominated by detached eddies originating at the top of the boundary layer, bringing relatively cold and dry air to the surface. This effect can be described in numerical models by either enhanced heat transfer coefficients for sensible and latent heat (Stanton and Dalton numbers respectively) or with an additional roughness length, added to the original roughness lengths for heat and humidity. Such new expressions are developed using turbulence measurements from the Baltic Sea valid for wind speeds up to 14 m s⁻¹. The effect of including the increased heat fluxes is investigated using two different numerical models: a regional three-dimensional climate model covering northern Europe, and a process-oriented ocean model for the Baltic Sea. During periods of several days, the latent heat flux can be increased by as much as 100 W m⁻². The increase in sensible heat flux is significantly smaller since the process is only of importance in the very near-neutral regime where the sensible heat flux is very small. The long-term average effect over the Baltic Sea is of the order of several W m⁻².     

A theoretical analysis of the effects of surface heterogeneity on the fluxes between ground and air

Summary The computation of the fluxes between ground surface and air in atmospheric models is based on the assumption that the surfaces parameters are horizontally homogeneous. In reality, the surface is heterogeneous, inducing a difference between the computed and realistic fluxes. Assuming that the distributions of temperature and humidity of the surface are normal, the difference of the fluxes for homogeneous and heterogeneous surface is found theoretically. The results show that the effect of the heterogeneity on the radiation flux is small, but attains a certain degree on the sensible and latent heat fluxes. However, this effect on the heat fluxes is not great when the standard deviation of the distribution of the surface parameters also is small. Only in case of great standard deviation, the difference may attain several W/m² even the order of magnitude of 10 W/m². Usually the computed sensible and latent heat fluxes are slightly greater for the heterogeneous case than that for homogeneous case, but when the interaction between the temperature and humidity of the surface is considered, the reverse is true. Received January 18, 2001 Revised July 31, 2001     

黑河实验区非均匀地表能量通量的数值模拟

利用三维非静力RAMS模拟研究了黑河实验区非均匀地表能量通量，模拟结果表明：绿洲地表净辐射通量较沙漠戈壁大；绿洲及沙漠戈壁下垫面上的Bowen比分别为0．4和4．0；夜间绿洲上整晚维持蒸发，并有负感热通量。模拟结果与测站实测结果与卫星反演值的对比研究指出，RAMS对绿洲下垫面潜热通量的模拟和沙漠戈壁下垫面感热通量的模拟与实测值基本一致。卫星遥感反演及数值模拟方法对净辐射的估算与实测较吻合，绿洲地表感热通量的卫星反演值较数值模拟结果更接近于实际，但潜热通量的模拟值则较卫星估算值更接近于实际；沙漠戈壁地表则是感热通量的模拟值较卫星反演值更接近于实际。上述分析为今后结合卫星遥感改进RAMS陆面过程参数化，使使用于模拟研究干旱区非均匀下垫面地气相互作用提供了可靠依据。     

Monin–Obukhov Similarity Functions for the Structure Parameters of Temperature and Humidity

Monin–Obukhov similarity functions for the structure parameters of temperature and humidity are needed to derive surface heat and water vapour fluxes from scintillometer measurements and it is often assumed that the two functions are identical in the atmospheric surface layer. Nevertheless, this assumption has not yet been verified experimentally. This study investigates the dissimilarity between the turbulent transport of sensible heat and water vapour, with a specific focus on the difference between the Monin–Obukhov similarity functions for the structure parameters. Using two datasets collected over homogeneous surfaces where the surface sources of sensible heat and water vapour are well correlated, we observe that under stable and very unstable conditions, the two functions are similar. This similarity however breaks down under weakly unstable conditions; in that regime, the absolute values of the correlations between temperature and humidity are also observed to be low, most likely due to large-scale eddies that transport unsteadiness, advection or entrainment effects from the outer layer. We analyze and demonstrate how this reduction in the correlation leads to dissimilarity between the turbulent transport of these two scalars and the corresponding Monin–Obukhov similarity functions for their structure parameters. A model to derive sensible and latent heat fluxes from structure parameters without measuring the friction velocity is tested and found to work very well under moderately to strongly unstable conditions (−z/L > 0.5). Finally, we discuss the modelling of the cross-structure parameter over wet surfaces, which is crucial for correcting water vapour effects on optical scintillometer measurements and also for obtaining surface sensible and latent heat fluxes from the two-wavelength scintillometry.     

A comparison of tropical oceanic heat fluxes determined by airborne eddy correlation and shipboard bulk aerodynamic techniques

Vertical turbulent transports of latent and sensible heat through the tropical marine boundary layer were measured with ship and airborne instruments in the GATE experimental area. The measurements from the two systems are compared for cases of simultaneous sampling in the same locations during undisturbed weather and during the wakes of convective disturbances. The paired average fluxes from the airborne eddy correlation measurements and the shipboard bulk aerodynamic measurements, for undisturbed weather, are related with correlation coefficients in the range of 0.6 to 0.9; the correlations depend primarily on stratifications of the aircraft data according to sampling altitude (15–153 m msl) and flight pattern relative to the mean wind. The agreement between the two types of measurements is best for ship data paired with aircraft samples from the lowest altitudes (15 and 30 m) and from alongwind rather than crosswind flights, as is appropriate since the stationary ships monitor the alongwind characteristics of the turbulence. The use of long (1–3 hr) versus short (10 min) ship samples did not significantly affect the comparability with the aircraft samples during undisturbed periods.The good baseline comparability demonstrated by the undisturbed-weather comparisons was applied to interpret the results from the wakes behind showers. Although these paired measurements were few, not only the sensible heat, but also the latent heat flux was shown to decrease substantially with altitude from 10 m to at least 150 m in the wakes, where the mixing was relatively intense. Variations in the fluxes were much greater at the higher level than nearer the sea surface.     

Regional turbulent statistics over contrasting natural surfaces

Summary Regional turbulent fluxes of momentum, sensible and latent heat collected over both agricultural and native vegetation in the south west of Australia are presented. Analysis of the energy spectrum illustrates that the most energetic eddies are between scales of 20 metres to 5 kilometres and highlights the spatial distance required to obtain representative regional fluxes. For the sensible heat flux, this distance is a function of measurement height whereas the latent flux is also influenced by surface variability. Statistics of these fluxes highlight that for the unstable surface layer, despite marked differences in the underlying vegetation and the corresponding sources of heat and moisture, heat is transported more efficiently than water vapour from the ground surface. Received October 9, 2000/Revised April 23, 2001     

Surface turbulent flux measurements over the Loess Plateau for a semi-arid climate change study

In order to provide high quality data for climate change studies, the data quality of turbulent flux measurements at the station of SACOL (Semi-Arid Climate & Environment Observatory of Lanzhou University), which is located on a semi-arid grassland over the Loess Plateau in China, has been analyzed in detail. The effects of different procedures of the flux corrections on CO₂, momentum, and latent and sensible heat fluxes were assessed. The result showed that coordinate rotation has a great influence on the momentum flux but little on scalar fluxes. For coordinate rotation using the planar fit method, different regression planes should be determined for different wind direction sectors due to the heterogeneous nature of the ground surface. Sonic temperature correction decreased the sensible heat flux by about 9%, while WPL correction (correction for density fluctuations) increased the latent heat flux by about 10%. WPL correction is also particularly important for CO₂ fluxes. Other procedures of flux corrections, such as the time delay correction and frequency response correction, do not significantly influence the turbulent fluxes. Furthermore, quality tests on stationarity and turbulence development conditions were discussed. Parameterizations of integral turbulent characteristics (ITC) were tested and a specific parameterization scheme was provided for SACOL. The ITC test on turbulence development conditions was suggested to be applied only for the vertical velocity. The combined results of the quality tests showed that about 62%–65% of the total data were of high quality for the latent heat flux and CO₂ flux, and as much as about 76% for the sensible heat flux. For the momentum flux, however, only about 35% of the data were of high quality.     

Scintillometer-Based Turbulent Fluxes of Sensible and Latent Heat Over a Heterogeneous Land Surface – A Contribution to Litfass-2003

The performance of a combined large aperture scintillometer (LAS) and a millimetre wave scintillometer (MWS) for estimating surface fluxes of sensible and latent heat over natural landscape is investigated, using data gathered during LITFASS-2003. For this purpose the LAS–MWS system was installed in a moderate heterogeneous landscape over a path length of 4.7 km with an effective beam height of 43 m. The derived surface fluxes have been compared with aggregated eddy-covariance (EC) measurements. The fluxes of sensible and latent heat from the LAS–MWS combination, as well as sensible heat fluxes of the single LAS, agreed fairly well with the EC-based fluxes, considering the uncertainties of the similarity stability functions and observed energy imbalance.