Thallium concentrations in seawater

Measurements of the concentration of thallium in seawater collected from numerous ocean locations ranged from 12 to 16 ng kg⁻¹. Variations between the Atlantic and Pacific Oceans, between the northern and southern hemispheres of the Pacific Ocean, and between surface and deep waters of both the Pacific and Atlantic oceans were comparable with the precision of the analyses. This relatively constant distribution indicates that the element's cycle in seawater may be similar to those of the alkali metals which are its principal biogeochemical analogues.     

The reliability of analytical data for tributyltin (TBT) in sea water and its implications on water quality criteria

To investigate the reliability of analytical data for tributyltin (TBT) in sea water, split water samples were distributed to ten laboratories in six countries. The sub-surface samples comprised: (i) an offshore (0·5 km) water sample, (ii) the same sample but spiked with an undisclosed quantity of TBT standard compound (175 ng TBT⁺ liter⁻¹), and (iii) a sample taken from a yacht marina. The seven acceptable data sets were in good agreement for the spiked sample (178 ± 26 ng TBT⁺ liter⁻¹) but showed a greater variation in concentrations reported for the yacht marina sample (366 ± 93 ng TBT⁺ liter⁻¹). Atomic absorption and gas chromatographic-flame photometric detection techniques produced results of similar accuracy and precision. Samples acidified with 1 ml of 10% (v/v) acetic acid appeared stable for more than 2 weeks when stored refrigerated and in darkness. Analyses of the offshore seawater sample revealed TBT contamination (9 ± 7 ng TBT⁺ liter⁻¹) indicating dispersion of the compound to the shelf waters off Monaco. The spread in values reported by the laboratories demonstrates inherent difficulties in obtaining good precision below approximately 20 ng TBT⁺ liter⁻¹. This observation is discussed with respect to the setting and enforcing of water quality standards.     

Dissolved Cd behaviour in some selected french and chinese estuaries. Consequences on Cd supply to the ocean

Few data on dissolved trace metals in rivers and estuaries are presently available. This paper is an attempt to provide additional data on dissolved concentrations obtained in polluted and so-called unpolluted river estuarine systems. Data for two major French rivers (Gironde, Rhône) have been compared with the Chinese Yellow River (Huanghe) and Yangtze River (Changjiang). Dissolved Cd concentrations have been measured by differential pulse anodic stripping voltammetry. Average concentrations range from 15 ng kg⁻¹ to 50 ng kg⁻¹ (0.13–0.45 nmol kg⁻¹) in the French rivers and are below 4 ng kg⁻¹ (0.040 nmol kg⁻¹) in the Chinese rivers.In all the estuaries studied the dissolved Cd concentrations depict a systematic bulge in the mixing zone which is attributed largely to remobilization processes from particulate matter when the chlorinity increases. Other parameters that may also play a significant role for remobilization are discussed. The processes concerned lead us to reassess the net Cd river input to the oceans, and this should be taken into account for a more precise evaluation of the residence time of oceanic Cd.     

Analysis of lead in polluted coastal seawater

The concentrations of total lead were determined in both ordinary coastal seawater and in coastal waters highly polluted with sewage. The average concentration of total lead ranged from about 25 ng/kg in surface samples of the former type to an average of 150 ng/kg in the latter type. 0.4⁻μm filtrate lead was found to be equivalent to lead extracted from untreated seawater by dithizone in chloroform. In highly polluted waters, particle lead ranged from 56 to 39% of the total lead, with the proportion increasing as the amount of sewage in the seawater increased. Virtually all of the lead in sewage is contained in the particle phase before it enters the ocean but about 11% is made freely available by cation exchange when the sewage is mixed with seawater. In ordinary coastal waters that are not highly polluted with sewage lead, particle lead ranged from 90 to > 20%, and most of this lead was associated with plankton. About one-third of total lead, or one-half of particle lead, in untreated seawater adheres to the walls of the water container within the first day. Upon prolonged standing (> 3 months) most of the remaining particle lead can be collected on the surface of algal colonies growing on the walls of the water container. The concentrations of freely available lead in seawater do not seem to be significantly affected by wall adsorption. The ²⁰⁶Pb/²⁰⁷Pb ratio of total lead in coastal surface seawater collected near Los Angeles was 1.194, and a day earlier was 1.188 near La Jolla. It is believed that this shows lack of mixing of contributions from two different sources of lead pollution: a pulse of rain-storm runoff of gasoline lead(²⁰⁶Pb/²⁰⁷Pb 1.197) from paved surfaces added to Los Angeles waters; and sewage lead (²⁰⁶Pb/²⁰⁷Pb 1.188) from San Diego added to La Jolla waters.     

Trace metal fronts in Scottish coastal waters

Dissolved cadmium and copper concentrations have been determined in 76 surface water samples in coastal and ocean waters around Scotland by anodic stripping voltammetry (ASV). A trace metal/salinity ‘front’ is observed to the west, north and north-east of Scotland separating high salinity ocean water (>35 × 10⁻³) with low concentrations of dissolved Cd and Cu from lower salinity (<35 × 10⁻³) coastal water containing higher concentrations of Cd and Cu. Mean Cd concentrations in ocean and coastal waters are 7 ng dm⁻³ (0·06 n ) and 11 ng dm⁻³ (0·10 n ) respectively; for Cu the respective levels are 60 ng dm⁻³ (0·95 n ) and 170 ng dm⁻³ (2·68 n ). The observed distribution is attributed principally to freshwater runoff and the advection of contaminated Irish Sea water into the study area.     

Development and assessment of an analytical system for the accurate and continual measurement of total dissolved inorganic carbon

An automated coulometric titration system based on that described by Johnson, Sieburth, Williams and Brandstrom (1987, Mar. Chem., 21: 117–133) has been evolved for the accurate and continual measurement of total dissolved inorganic carbon (TCO₂). The instrument achieves an analytical precision (1 SD) of ±0.5–1.0 μmol kg⁻¹ (0.025–0.05%). The accuracy of the system has been examined by a limited comparison with other coulometric-based titrators and with a manometric-based system; agreement was to 1 μmol kg⁻¹. The capability for automatic continual analysis allows surface mapping of TCO₂; a sample rate of 10 analyses h⁻¹ gives a mapping resolution of 1–2 km. Provision for frequent standardization with a liquid substandard has been included in the development. The ability to achieve high-density analyses while maintaining interlaboratory consistency and standardization constitutes a vital contribution to surveys of ocean carbon chemistry (e.g. Joint Global Ocean Flux Study, World Ocean Circulation Experiment).     

Assessing site-specific effects of TBT contamination with mussel growth rates

During nine field transplant tests in San Diego Bay (1987–1990), juvenile mussels were exposed to mean concentrations of tributyltin (TBT) in ambient seawater ranging from 2 to 530 ng liter⁻¹ for 12 weeks under natural conditions. A total of 79 cages with 18 mussels each were monitored at 18 different sites. Growth and seawater TBT concentrations were measured weekly or on alternate weeks (biweekly). Mean growth rates ranged from 17 to 505 mg week⁻¹ (0·2 to 2·5 mm week⁻¹). Accumulation of TBT in mussel tissues was measured at the end of each 12-week test exposure and ranged from 0·1 to 3·2 μg g⁻¹ TBT wet weight. The frequency of the measurements and the integration of chemical and biological measurements improved the accuracy of the assessment over more traditional approaches. Growth was significantly related to seawater and tissue TBT. The statistical relationships with growth effects were used to estimate chemical effect zones for TBT in San Diego Bay. Site-specific differences were distinguished by additional statistical analyses and consideration of environmental significance.     

A method to measure the isotopic (C) composition of dissolved organic carbon using a high temperature combustion instrument

The stable isotopes of dissolved organic carbon (DOC) are a powerful tool for distinguishing sources and inputs of organic matter in aquatic systems. While several methods exist to perform these analyses, no labs routinely utilize a high temperature combustion (HTC) instrument. Advantages of HTC instruments include rapid analysis, small sample volumes and minimal sample preparation, making them the favored devices for most routine oceanic DOC concentration measurements. We developed a stable carbon DOC method based around an HTC system. This method has the benefit of a simple setup, requiring neither vacuum nor high pressures. The main drawback of the method is a significant blank, requiring careful accounting of all blank sources for accurate isotopic and concentration values. We present here a series of experiments to determine the magnitude, source and isotopic composition of the HTC blank. Over time, the blank is very stable at  20 ng of carbon with a δ¹³C of − 18.1‰ vs. VPDB. The similarity of the isotopic composition of the blank and seawater samples makes corrections relatively minor. The precision of the method was determined by oxidizing organic standards with a wide isotopic and concentration range (− 9‰ to − 39‰; 18 μM to 124 μM). Analysis of seawater samples demonstrates the accuracy for low concentration, high salinity samples. The overall error on the measurement is approximately ± 0.8‰.     

Winkler's method overestimates dissolved oxygen in seawater: Iodate interference and its oceanographic implications

Dissolved oxygen in seawater has been determined by using the Winkler's reaction scheme for decades. An interference in this reaction scheme that has been heretofore overlooked is the presence of naturally occurring iodate in seawater. Each mole of iodate can result in an apparent presence of 1.5 mol of dissolved oxygen. At the concentrations of iodate in the surface and deep open ocean, it can lead to an overestimation of 0.52 ± 0.15 and 0.63 ± 0.05 μmol kg^− 1 of oxygen in these waters respectively. In coastal and inshore waters, the effect is less predictable as the concentration of iodate is more variable. The solubility of oxygen in seawater was likely overestimated in data sources that were based on the Winkler's reaction scheme for the determination of oxygen. The solubility equation of García and Gordon [Garcia H.E., Gordon, L.I., 1992. Oxygen solubility in seawater: Better fitting equations. Limnol. Oceanogr. 37, 1307–1312] derived from the results of Benson and Krause [Benson, F.B., Krause, D. Jr., 1984. The concentration and isotopic fractionation of oxygen dissolved in freshwater and seawater in equilibrium with the atmosphere. Limnol. Oceanogr. 29, 620–632] is free from this source of error and is recommended for general use. By neglecting the presence of iodate, the average global super-saturation of oxygen in the surface oceans and the corresponding efflux of oxygen to the atmosphere both have been overestimated by about 8%. Regionally, in areas where the degree of super-saturation or under-saturation of oxygen in the surface water is small, such as in the tropical oceans, the net air–sea exchange flux can be grossly under- or overestimated. Even the estimated direction of the exchange can be reversed. Furthermore, the presence of iodate can lead to an overestimation of the saturation anomaly of oxygen in the upper ocean attributed to biological production by 0.23 ± 0.07%. AOU may have been underestimated by 0.52 ± 0.15 and 0.63 ± 0.05 μmol kg^− 1 in the surface mixed layer and deep water, while preformed phosphate and preformed nitrate may have been overestimated by 0.004 ± 0.001 and 0.06 ± 0.02 μmol kg^− 1 in the surface mixed layer, and 0.005 ± 0.0004 and 0.073 ± 0.006 μmol kg^− 1 in the deep water. These are small but not negligible corrections, especially in areas where the values of these parameters are small. At the increasing level of sophistication in the interpretation of oxygen data, this source of error should now be taken into account. Nevertheless, in order to avoid confusion, an internationally accepted standard needs to be adopted before these corrections can be applied.     

The behaviour of dissolved Cd, Co, Zn, and Pb in North Atlantic near-surface waters (30°N/60°W–60°N/2°W)

In September 1993 (M26) and June/July 1996 (M36), a total of 239 surface samples (7 m depth) were collected on two transects across the open Atlantic Ocean (224 samples) and northwest European shelf edge area. We present an overview of the horizontal variability of dissolved Cd, Co, Zn, and Pb in between the northwest and northeast Atlantic Ocean in relation to salinity and the nutrients. Our data show a preferential incorporation of Cd relative to P in the particulate material of the surface ocean when related to previously published parallel measurements on suspended particulate matter from the same cruise. There is a good agreement with results recently estimated from a model by Elderfield and Rickaby (Nature 405 (2000) 305), who predict for the North Atlantic Ocean a best fit for α_Cd/P=[Cd/P]_POM/[Cd/P]_SW of 2.5, whereas the approach of our transect shows a α_Cd/P value of 2.6. The Co concentrations of our transects varied from <5 to 131 pmol kg⁻¹, with the lowest values in the subtropical gyre. There were pronounced elevations in the low-salinity ranges of the northwest Atlantic and towards the European shelf. The Co data are decoupled from the Mn distribution and support the hypothesis of marginal inputs as the dominant source. Zinc varied from a minimum of <0.07 nmol kg⁻¹ to a maximum of 1.2 and 4.8 nmol kg⁻¹ in regions influenced by Labrador shelf or European coastal waters, respectively. In subtropical and northeast Atlantic waters, the average Zn concentration was 0.16 nmol kg⁻¹. Zinc concentrations at nearly three quarters of the stations between 40°N and 60°N were <0.1 nmol kg⁻¹. This suggests that biological factors control Zn concentrations in large areas of the North Atlantic surface waters. The Pb data indicated that significant differences in concentration between the northwest and northeast Atlantic surface waters presently (1996) do not exist for this metal. The transects in 1993 and 1996 exhibited Pb concentrations in the northeast Atlantic surface waters of 30 to 40 pmol kg⁻¹, about a fifth to a quarter of the concentrations observed in 1981. This decline is supported by our particle flux measurements in deep waters of the same region.     

A Gibbs–Pitzer function for high-salinity seawater thermodynamics

A high-salinity Gibbs function for seawater is derived from Pitzer equations of the sea salt components, in conjunction with the 2003 Gibbs function of seawater for low salinities. Various properties, computed from both formulations by thermodynamic rules, are compared with each other, and with high-salinity measurements. The new Gibbs–Pitzer function presented in this paper is valid in the range 0–110 g kg⁻¹ in absolute salinity, −7 to +25 °C in temperature, and 0–100 MPa in applied pressure. The formulation is expressed in the International Temperature Scale 1990 (ITS-90), and is consistent with the International Standard for Fluid Water (IAPWS-95), and with the 2005/2006 equations of state of ice Ih.     

CO<Subscript>2</Subscript> Flux Measurements over the Sea Surface by Eddy Correlation and Aerodynamic Techniques

The measurements of the vertical transport of CO₂ were carried out over the Sea of Japan using the specially designed pier of Kyoto University on September 20 to 22, 2000. CO₂ fluxes were measured by the eddy correlation and aerodynamic techniques. Both techniques showed comparable CO₂ fluxes during sea breeze conditions: −0.001 to −0.08 mg m⁻²s⁻¹ with the mean of −0.05 mg m⁻²s⁻¹. This means that the measuring site satisfies the fetch requirement for meteorological observations under sea breeze conditions. Moreover, the eddy diffusivity coefficient used in the aerodynamic technique is found to be consistent with the coefficient used in the eddy correlation technique. The present result leads us to conclude that the aerodynamic technique may be applicable to underway CO₂ flux measurements over the ocean and may be used in place of the bulk technique. The important point is the need to maintain a measuring accuracy of CO₂ concentration difference of the order of 0.1 ppmv on the research vessels or the buoys.     

Measurement of manganese, zinc and cadmium complexation in seawater using Chelex ion exchange equilibria

Equilibria between Chelex 100* and manganese, zinc and cadmium ions were used to determine the complexation of these trace metals in 36‰ Gulf Stream seawater at 25°C and pH 8.2. The method utilized radiotracers (⁵⁴Mn, ⁶⁵Zn, and ¹⁰⁹Cd) to quantify trace metal adsorption from trace metal-amended seawater and from seawater containing a series of ethylenediaminetetracetate (EDTA)—metal ion buffers. Results were consistent with Chelex adsorption of both trace metal ions and trace metal—EDTA chelates. Equilibrium models fitted to the data were used to establish conditional stability constants for Chelex adsorption of manganese, zinc and cadmium ions and for adsorption of EDTA-chelates. These models also yielded ratios of free metal ions to total dissolved trace metal concentrations in seawater: 10^−0.1 for manganese, 10^−0.2 for zinc, and 10^−1.5 for cadmium. Independent measurements with a cadmium ion-selective electrode also yielded a free: total cadmium ratio of 10^−1.5.     

Photochemical production of molecular hydrogen in lake water and coastal seawater

Samples of lake water and coastal seawater from Nova Scotia, Canada, were irradiated with natural or artificial sunlight to investigate the potential for photochemical hydrogen production. Hydrogen photo-production was observed in all natural water samples. Rates of hydrogen formation were highest in coloured lake water (range: 98–163 pmol L^− 1h^− 1) and lower in seawater (range: 19–45 pmol L^− 1 h ^− 1). Dilutions of the most highly coloured lake sample (Kejimkujik Lake) showed a positive linear relationship between H₂ production rates and CDOM concentration. Photo-production rates normalised to UV absorption coefficients at 350 nm indicated that the photochemical efficiency of hydrogen formation varied between samples, perhaps due to differences in the CDOM composition. Photochemical hydrogen formation was also seen in solutions of syringic acid and acetaldehyde: two low-molecular-weight carbonyl compounds found in natural waters. Photochemistry may therefore offer least a partial explanation for the persistently high levels of hydrogen observed in the low-latitude surface ocean.     

Calibration of a chalcogenide glass membrane ion-selective electrode for the determination of free Fe in seawater: I. Measurements in UV photooxidised seawater

Calibration of a chalcogenide glass membrane, Fe(III)ISE [Fe_2.5(Ge₂₈Sb₁₂Se₆₀)_97.5], in buffered saline media has been undertaken in order to assess the suitability of this ISE for seawater analyses. The electrode slopes in saline citrate and salicylate buffers were 26.3 and 28.2 mV/decade, respectively, for Fe³⁺ concentrations ranging from 10⁻¹⁰ M to less than 10⁻²⁵ M Fe³⁺. The calibration lines in the citrate and salicylate buffers were essentially collinear with the response in unbuffered chloride-free standards containing >10⁻⁵ M Fe³⁺, demonstrating that the response of the FeISE is unaffected by chloride ions. A mechanism involving a combination of charge transfer and ion-exchange of Fe(III), at the electrode diffusion layer, can be used to explain the ≈30 mV/decade slope of the FeISE. The response of the FeISE in UV photooxidised seawater containing 8 nM total Fe was measured as the pH was changed from 8.27 to 3.51. The slope of the response was 24.2 mV/decade [Fe³⁺] calculated as a function of pH using Fe(III) hydrolysis constants for seawater. Moreover, the response was essentially collinear with that in citrate buffers and in unbuffered solutions containing >10⁻⁵ M Fe³⁺ and the slope for the combined data was 26.2 mV/decade. This study was restricted to organic-free seawater because the certainty in Fe(III)–ligand stability constants is insufficient to warrant the selection of an ideal calibration buffer system, and there is evidence that powerful chelating ligands (e.g., EDTA along with humic and fulvic acids) may alter the response of the Fe(III)ISE. The Fe dissolution rate of the FeISE in UV photooxidised seawater was found to be 1.6×10⁻² nmol Fe/min, as measured by cathodic stripping voltammetry (CSV). This would contaminate a 100-ml sample by 0.8–1.6 nM Fe over a typical measurement period of 5–10 min obtained using a stability criterion of 0.5 mV/min. Various methods are proposed for reducing the level of contamination in open ocean samples that contain sub-nanomolar concentrations of iron. The FeISE has the potential to detect free Fe³⁺ at concentrations typically found in natural seawater.     

Evaluation of atmospheric transport as a nonpoint source of polycyclic aromatic hydrocarbons in marine sediments of the Eastern Mediterranean

Coastal marine sediment, air and seawater samples were collected at six sampling stations in the Eastern Mediterranean Sea distant from pollutant point sources. All sediment samples were analyzed to determine polycyclic aromatic hydrocarbon (PAH), black carbon (BC) and organic carbon (OC) contents. The PAH contents of gaseous and seawater samples of the study were determined in order to evaluate the role of air–sea exchange as PAH nonpoint source to the marine sediments. The average concentration of the total PAHs (∑PAHs) in the sediments varied from 2.2 to 1056.2 ng g⁻¹ dry weight. The average BC and OC contents varied from 0.3 to 5.6 and from 2.9 to 21.4 mg g⁻¹ dry weight, respectively. ∑PAH concentration in the marine atmosphere varied from 20.0 to 83.2 ng m⁻³. Air–water exchange flux (F_A–W) estimation has indicated air transport as a significant source of PAHs to pristine marine sediments of Eastern Mediterranean. In addition, the significant correlation between the PAHs and the organic and soot carbon content further suggests the importance of atmospheric input of PAHs to the sediments.     

The shipboard analysis of trace levels of sulfur hexafluoride, chlorofluorocarbon-11 and chlorofluorocarbon-12 in seawater

Methods are described for the rapid (11 min) automated shipboard analysis of dissolved sulfur hexafluoride (SF₆) in small volume (200 cm³) seawater samples. Estimated precision for the SF₆ measurements is 2% or 0.02 fmol kg⁻¹ (whichever is greater). The method also allows for the simultaneous measurement of chlorofluorocarbon-11 (CFC11) and chlorofluorocarbon-12 (CFC12) on the same water sample, with significantly improved sensitivity over previous analytical methods.     

Simultaneous determination of dissolved organic carbon and total dissolved nitrogen in seawater by high temperature catalytic oxidation: conditions for precise shipboard measurements

Appropriate conditions have been achieved for the accurate, rapid, and highly precise shipboard simultaneous determination of dissolved organic carbon and total dissolved nitrogen in seawater by high temperature catalytic oxidation. A nitrogen-specific Antek 705D chemiluminescence detector and a CO₂-specific LiCor Li6252 IRGA have been coupled in-series with a Shimadzu TOC-5000 organic carbon analyser. Precision of both simultaneous measurements is ≤1.5%, i.e. ±1 μmol C l⁻¹ and ±0.3 μmol N l⁻¹, respectively. Quality of analysis is not compromised by vibrations associated with ocean going research vessels.     

Oxygen minimum zones in the eastern tropical Atlantic and Pacific oceans

Within the eastern tropical oceans of the Atlantic and Pacific basin vast oxygen minimum zones (OMZ) exist in the depth range between 100 and 900 m. Minimum oxygen values are reached at 300–500 m depth which in the eastern Pacific become suboxic (dissolved oxygen content <4.5 μmol kg⁻¹) with dissolved oxygen concentration of less than 1 μmol kg⁻¹. The OMZ of the eastern Atlantic is not suboxic and has relatively high oxygen minimum values of about 17 μmol kg⁻¹ in the South Atlantic and more than 40 μmol kg⁻¹ in the North Atlantic. About 20 (40%) of the North Pacific volume is occupied by an OMZ when using 45 μmol kg⁻¹ (or 90 μmol kg⁻¹, respectively) as an upper bound for OMZ oxygen concentration for ocean densities lighter than σ_θ < 27.2 kg m⁻³. The relative volumes reduce to less than half for the South Pacific (7% and 13%, respectively). The abundance of OMZs are considerably smaller (1% and 7%) for the South Atlantic and only 0% and 5% for the North Atlantic. Thermal domes characterized by upward displacements of isotherms located in the northeastern Pacific and Atlantic and in the southeastern Atlantic are co-located with the centres of the OMZs. They seem not to be directly involved in the generation of the OMZs.OMZs are a consequence of a combination of weak ocean ventilation, which supplies oxygen, and respiration, which consumes oxygen. Oxygen consumption can be approximated by the apparent oxygen utilization (AOU). However, AOU scaled with an appropriate consumption rate (aOUR) gives a time, the oxygen age. Here we derive oxygen ages using climatological AOU data and an empirical estimate of aOUR. Averaging oxygen ages for main thermocline isopycnals of the Atlantic and Pacific Ocean exhibit an exponential increase with density without an obvious signature of the OMZs. Oxygen supply originates from a surface outcrop area and can also be approximated by the turn-over time, the ratio of ocean volume to ventilating flux. The turn-over time corresponds well to the average oxygen ages for the well ventilated waters. However, in the density ranges of the suboxic OMZs the turn-over time substantially increases. This indicates that reduced ventilation in the outcrop is directly related to the existence of suboxic OMZs, but they are not obviously related to enhanced consumption indicated by the oxygen ages. The turn-over time suggests that the lower thermocline of the North Atlantic would be suboxic but at present this is compensated by the import of water from the well ventilated South Atlantic. The turn-over time approach itself is independent of details of ocean transport pathways. Instead the geographical location of the OMZ is to first order determined by: (i) the patterns of upwelling, either through Ekman or equatorial divergence, (ii) the regions of general sluggish horizontal transport at the eastern boundaries, and (iii) to a lesser extent to regions with high productivity as indicated through ocean colour data.