首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
利用澳大利亚悉尼观测站连续16年的实测资料,并结合波高阈值法以及年N大波法两种新的采样方法,利用最小二乘法原理,对对数正态分布、Gumbel第一型极值分布、Weibull分布、指数分布和皮尔逊Ⅲ型曲线五种分布函数进行分析和比较,从而选出一种适用的分布函数。同时,文章介绍了一种最新的估计三参数Weibull分布参数的方法。结果表明:三参数Weibull分布函数的相关系数较大,拟合较好,而且均方误也都较小。从而得出结论,三参数Weibull分布函数得到的结果较好,并建议使用该分布函数进行设计波高的计算。  相似文献   

2.
在概率分布线型确定下,水文频率计算就是根据样本资料估算其中包含的参数。计算P-Ⅲ型分布参数的方法很多,目前常采用的最简单的方法是三点法,用图解适线求参数。本文中笔者建议用二点法直接利用K值表求参数。该方法简便,且不易出错。同时又能保证适线法的精度要求。  相似文献   

3.
简要论述了Copula理论与几种常用的二维Archimedean Copula函数的性质和适用性。以粤东汕头海域妈屿历年最高增水高度与相应风速的遭遇为研究实例,在分别采用3个三参数的概率分布模式:广义极值分布(GEV)、Weibull分布(WBL)和皮尔逊Ⅲ型(P-Ⅲ)分布对两个边缘分布(年最高增水高度与相应风速)拟合优度检验基础上构建了两变量联合概率分布模型。主要结果如下:(1) 年最大增水高度与相应风速的边缘分布分别服从Weibull分布和P-Ⅲ型分布;(2) 拟合优度检验指标表明二者的最优连接函数为Archimedean Copula类的Gumbel-Hougaard Copula;(3) 重现期介于2~200 a之间的边缘分布与同频率的联合分布的重现水平相对差值大约介于6.7%~22.2%之间;(4) 特定风速设计频率条件下,随年最大增水设计频率的减小,二者的遭遇概率也随之迅速减小;反之,特定增水设计频率随风速条件频率的减小,二者的遭遇概率随之明显增大。  相似文献   

4.
张秀芝 《海洋预报》1994,11(3):55-61
本文应用Weibull分布各参数的概率权重矩表达式,估计Weibull分布参数,并用该分布推算一百年一遇最大风速值,与目前国内较为流行的极值Ⅰ型和对数正态分布推算值比较接近。通过统计检验对概率权重矩法与最小二乘法和最大似然法进行比较,结果表明,虽然其拟合优度与最小二乘法和最大似然法相当,但计算过程要简单得多。  相似文献   

5.
年极值波浪长期分布推算的探讨   总被引:1,自引:0,他引:1  
一、前言极值波浪的长期分布规律对于海港和海上建筑物的设计是极为重要的。它包括对极值波浪系列选定一个合适的概率分布,并外延确定一个合适的设计值。在我国“海港水文”规范中,建议用皮尔逊Ⅲ型分布来拟合经验频率曲线,在实际工作中,适线时常常为照顾首部累积率很小的一两个大值及尾部若干小值等少数点据而人为地调整 CV 及 Cs  相似文献   

6.
墨西哥湾波候统计特性分析   总被引:2,自引:0,他引:2  
简要介绍了波候的概念,简述Weibull分布及对数一正态分布的拟合方法,提出最大熵分布拟合有效波高、峰周期分布的新方法;选取半封闭海湾墨西哥湾内水深不同、地理位置不同的六个观测站一年的连续资料,以上述三种拟合方法对其有效波高,峰周期概率分布进行拟合,并与观测直方图进行比较检验,结果表明,在墨西哥海湾内,最大熵分布优于对数-正态分布,对数-正态分布优于Weibull分布。  相似文献   

7.
基于广义极值分布的设计波高推算   总被引:1,自引:0,他引:1  
简介了广义极值分布函数及其3种参数估计方法,包括极大似然(ML)、线性矩(LM)和间隔最大积(MPS)估计的计算方法。使用广义极值分布函数推算了北部湾涠洲岛海域3个波向的年波高极值序列设计波高,并与Weibull分布、Gumbel分布和皮尔逊Ⅲ型分布的推算结果加以对比。分析表明,涠洲岛海域极值波高服从于广义极值Ⅲ型分布,拟合优度检验结果表明广义极值分布能更好地拟合极值波高;MPS方法是一种优良的参数估计法,推算的设计波高可作为海岸环境工程设计的首要参考值。  相似文献   

8.
年极值波浪长期分布的研究   总被引:1,自引:0,他引:1  
本文指出现行海港水文规范中设计波浪频率分析计算的缺点并探讨了用对数正态分布律来拟合年极值波浪的可能性。提出了理论频率曲线的抽样误差:探讨了经验频率计算公式,试用建筑物使用年限及危险率作为设计波浪标准的可能性。  相似文献   

9.
极值风速重现期不仅是海岸工程设计的重要参考项,也是海洋预报部门发布预报、预警的重要依据。因此,本文通过统计分析1949-2015年之间经过浙江近海的热带气旋过程中的风速极值,采用P-III分布和Gumbel分布求矩适线法对其进行重现期的计算。由最小二乘法准则可知,P-III分布求矩适线法的拟合曲线优于Gumbel分布求矩适线法的拟合曲线,能够很好地拟合实测数据序列。比较P-III分布和Gumbel分布的计算结果可知,P-III分布计算结果更符合实测数据,且其计算的百年一遇极值风速设计值为92.26m/s。此外,文中还对计算方法进行了Matlab编程设计,以自适应的过程选取与数据序列拟合最好的曲线,不仅在计算方法上,而且在操作方式上,都较传统适线法更具有客观性和有效性。  相似文献   

10.
极值分布的推算方法及其在黄河口海区的应用   总被引:1,自引:0,他引:1  
本文介绍了以两种不同类型的样本求取多年一遇极值的推算方法。第一种类型是用长期资料的年极值为样本,分别依耿贝尔极值分市(矩法估算参数和最小二乘法估算参数)、第一极值分布、皮尔逊Ⅲ型分布,推算了多年一遇的风暴增水和水位;对所有这些分布的推算结果,用柯尔莫哥洛夫方法进行了测适度检验,给出了95%的可信度。第二种类型用短期连续资料力样本,以三个月的实测水位资料用Weibull分布推算了不同重现期的水位。用两种类型推算的结果是相同的。  相似文献   

11.
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.  相似文献   

12.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明:土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。  相似文献   

13.
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.  相似文献   

14.
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.  相似文献   

15.
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.  相似文献   

16.
17.
18.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.  相似文献   

19.
A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria ( 〉 99% ), but also between polar marine bacteria and bacteria from other aquatic environments ( ≥ 98.8% ), including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.  相似文献   

20.
Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号