The potential for metal contamination during Apollo lunar sample curation

Curation and preparation of samples for chemical analysis can occasionally lead to significant contamination. This issue is of concern in the study of lunar samples, especially those from the Apollo sample collection, where available masses are finite. Here we present compositional data for stainless steels that have commonly been used in the processing of Apollo lunar samples at NASA Johnson Space Center, including a chisel and a vessel typically used to transfer Apollo samples to principal investigators. The Type 304 stainless steels are Cr-rich, with high concentrations of Mn (4000–18,000 μg g⁻¹), Cu (1000–22,900 μg g⁻¹), Mo (1030–1120 μg g⁻¹), and W (72–193 μg g⁻¹). They have elevated highly siderophile element (HSE) concentrations (up to 92 ng g⁻¹ Os), ¹⁸⁷Os/¹⁸⁸Os ranging from 0.1310 to 0.1336, and negligible lithophile element abundances. We find that, while metal contamination is possible, significant (≫0.01% by mass) addition of stainless steel is required to strongly affect the composition of the HSE, W, Mo, Cr, or Cu for most Apollo lunar samples. Nonetheless, careful appraisal on a case-by-case basis should take place to ensure contamination introduced through sample processing during curation is at acceptably low levels. A survey of lunar mare basalts and crustal rocks indicates that metal contamination plays a negligible role in the compositional variability of the HSE and W compositions preserved in these samples. Further work to constrain contamination for other properties of Apollo samples is required (e.g., organics, microbes, water, noble gases, and magnetics), but the effect of metal contamination can be well-constrained for the Apollo lunar collection.     

From 2D to 3D chondrule size data: Some empirical ground truths

In order to characterize the relation between apparent chondrule sizes (2D) and true chondrule sizes (3D), three ordinary chondrites of the H, L, and LL group have been analyzed. The diameters of a large number of chondrule cut faces in thin sections (2D; n = 2037) and of separated chondrules from the same meteorites (3D: n = 2061) have been measured. The obtained 2D/3D mean chondrule sizes (μm) for the H, L, and LL chondrite are 450/490, 500/610, and 690/830; the corresponding median values (μm) are 370/420, 450/530, and 580/730. The data show that there is a cutoff for small chondrule sizes in each sample. Possibly characteristic minimum sizes exist for the various groups, increasing in the (3D) sequence H (~90 μm) <L (~180 μm) <LL (~240 μm). No systematics were found for the maximum chondrule sizes. The investigated samples show very similar chondrule volume (mass) distributions relative to the mode (peak) of their size-frequency distributions. About 2.6–2.9% and 97.1–97.4% of the total chondrule volume (mass) is present in chondrule sizes smaller and larger than the mode, respectively. It was found that 2D sectioning consistently results in a shift of the true 3D size-frequency distributions toward smaller sizes. This effect leads to the underestimation of the values for (1) the true mean chondrule size by 8–18%, (2) the true chondrule median value by 12–21%, and (3) the true mode value of the size-frequency distributions by 12–17% (50 μm binning). This is the opposite of what popular 2D/3D correction models predict (e.g., Eisenhour 1996 ).     

Quantifying noble gas contamination during terrestrial alteration in Martian meteorites from Antarctica

We investigated exterior and interior subsamples from the Martian shergottite meteorites Allan Hills (ALH) A77005 and Roberts Massif (RBT) 04261 for secondary minerals, oxygen isotopes, Ar‐Ar, and noble gas signatures. Electron microprobe investigations revealed that RBT 04261 does not contain any visible alteration even in its most exterior fractures, whereas fracture fillings in ALHA77005 penetrate into the meteorite up to 300 μm, beyond which the fractures are devoid of secondary minerals. Light noble gases seem to be almost unaffected by terrestrially induced alteration in both meteorites. Thus, a shock metamorphic overprint of 30–35 GPa can be deduced from the helium measurements in RBT 04261. Oxygen isotopes also seem unaffected by terrestrially weathering and variations can easily be reconciled with the differences in modal mineralogy of the exterior and interior subsamples. The measurements on irradiated samples (Ar‐Ar) showed a clear Martian atmospheric contribution in ALHA77005, but this is less apparent in our sample of RBT 04261. Exterior and interior subsamples show slight differences in apparent ages, but the overall results are very similar between the two. In contrast, krypton and xenon are severely affected by terrestrial contamination, demonstrating the ubiquitous presence of elementally fractionated air in RBT 04261. Although seemingly contradictory, our results indicate that RBT 04261 was more affected by contamination than ALHA77005. We conclude that irrespective of on which planet the alteration occurred, exposure of Martian rocks to atmosphere (or brine) introduces noble gases with signatures elementally fractionated relative to the respective atmospheric composition into the rock, and relationships of that process with oxygen isotopes or mineralogical observations are not straightforward.     

The effects of possible contamination by sample holders on samples to be returned by Hayabusa2

Chemical compositions of materials used for new sample holders (vertically aligned carbon nanotubes [VACNTs] and polyimide film), which were developed for the analysis of Hayabusa2‐return samples, were determined by instrumental neutron activation analysis and/or instrumental photon activation analysis, to estimate contamination effects from the sample holders. The synthetic quartz plate used for the sample holders was also analyzed. Ten elements (Na, Al, Cr, Mn, Fe, Ni, Eu, W, Au, and Th) and 14 elements (Na, Al, K, Sc, Ti, Cr, Zn, Ga, Br, Sb, La, Eu, Ir, and Au) could be detected in the VACNTs and polyimide film, respectively. The VACNT data show that contamination by this material with respect to the Murchison meteorite is negligible in terms of the elemental ratios (e.g., Fe/Mn, Na/Al, and Mn/Cr) used for the classification of meteorites due to the extremely low density of VACNTs. However, for the Au/Cr ratio, even small degrees (1.7 wt%) of contamination by VACNTs will change the Au/Cr ratio. Elemental ratios used for the classification of meteorites are only influenced by large amounts of contamination (>60 wt%) of polyimide film, which is unlikely to occur. In contrast, detectable effects on Ti isotopic compositions are caused by >0.1 and >0.3 wt% contamination by VACNTs and polyimide film, respectively, and Hf isotopic changes are caused by >0.1 wt% contamination by VACNTs. The new sample holders (VACNTs and polyimide film) are suitable for chemical classification of Hayabusa2‐return samples, because of their ease of use, applicability to multiple analytical instruments, and low contamination levels for most elements.     

Macroscopic subdivision of silica aerogel collectors for sample return missions

Abstract— Silica aerogel collector tiles have been employed for the collection of particles in low Earth orbit and, more recently, for the capture of cometary particles by NASA's Stardust mission. Reliable, reproducible methods for cutting these and future collector tiles from sample return missions are necessary to maximize the science output from the extremely valuable embedded particles. We present a means of macroscopic subdivision of collector tiles by generating large‐scale cuts over several centimeters in silica aerogel with almost no material loss. The cut surfaces are smooth and optically clear allowing visual location of particles for analysis and extraction. This capability is complementary to the smaller‐scale cutting capabilities previously described (Westphal 2004; Ishii 2005a, 2005b) for removing individual impacts and particulate debris in tiny aerogel extractions. Macroscopic cuts enable division and storage or distribution of portions of aerogel tiles for immediate analysis of samples by certain techniques in situ or further extraction of samples suited for other methods of analysis. The capability has been implemented in the Stardust Laboratory at NASA's Johnson Space Center as one of a suite of aerogel cutting methods to be used in Stardust sample curation.     

Refractory materials in comet samples

Transmission electron microscope examination of more than 250 fragments, >1 μm from comet Wild 2 and a giant cluster interplanetary dust particle (GCP) of probable cometary origin has revealed four new calcium‐aluminum‐rich inclusions (CAIs), an amoeboid olivine aggregate (AOA), and an additional AOA or Al‐rich chondrule (ARC) object. All of the CAIs have concentric mineral structures and are composed of spinel + anorthite cores surrounded by Al,Ti clinopyroxenes and are similar to two previous CAIs discovered in Wild 2. All of the cometary refractory objects are of moderate refractory character. The mineral assemblages, textures, and bulk compositions of the comet CAIs are similar to nodules in fine‐grained, spinel‐rich inclusions (FGIs) found in primitive chondrites and like the nodules may be nebular condensates that were altered via solid–gas reactions in the solar nebula. Oxygen isotopes collected on one Wild 2 CAI also match FGIs. The lack of the most refractory inclusions in the comet samples may reflect the higher abundances of small moderately refractory CAI nodules that were produced in the nebula and the small sample sizes collected. In the comet samples, approximately 2–3% of all fragments larger than 1 μm, by number, are CAIs and nearly 50% of all bulbous Stardust tracks contain at least one CAI. We estimate that ~0.5 volume % of Wild 2 material and ~1 volume % of GCP is in the form of CAIs. ARCs and AOAs account for <1% of the Wild 2 and GCP grains by number.     

Mineralogical characterization of some basaltic asteroids in the neighborhood of (4) Vesta: first results

We present reflectance spectra of 19 V-type asteroids obtained at the 3.6 m Telescopio Nazionale Galileo covering 0.8 to 2.5 μm. For 8 of these asteroids we obtained also visible spectra in the same observational run. The range from 0.8 to 2.5 μm, encompassing the 1 and 2 μm pyroxene features, allows a precise mineralogical characterization of these asteroids. The obtained data suggests the possible coexistence of distinct mineralogical groups among the V-type asteroids, either probing different layers of (4) Vesta or coming from different bodies. No clear correlation was found between mineralogies and the objects being, or not, member of the Vesta dynamical family.     

Heterogeneous distribution of H2O in the Martian interior: Implications for the abundance of H2O in depleted and enriched mantle sources

We conducted a petrologic study of apatite within 12 Martian meteorites, including 11 shergottites and one basaltic regolith breccia. These data were combined with previously published data to gain a better understanding of the abundance and distribution of volatiles in the Martian interior. Apatites in individual Martian meteorites span a wide range of compositions, indicating they did not form by equilibrium crystallization. In fact, the intrasample variation in apatite is best described by either fractional crystallization or crustal contamination with a Cl‐rich crustal component. We determined that most Martian meteorites investigated here have been affected by crustal contamination and hence cannot be used to estimate volatile abundances of the Martian mantle. Using the subset of samples that did not exhibit crustal contamination, we determined that the enriched shergottite source has 36–73 ppm H₂O and the depleted source has 14–23 ppm H₂O. This result is consistent with other observed geochemical differences between enriched and depleted shergottites and supports the idea that there are at least two geochemically distinct reservoirs in the Martian mantle. We also estimated the H₂O, Cl, and F content of the Martian crust using known crust‐mantle distributions for incompatible lithophile elements. We determined that the bulk Martian crust has ~1410 ppm H₂O, 450 ppm Cl, and 106 ppm F, and Cl and H₂O are preferentially distributed toward the Martian surface. The estimate of crustal H₂O results in a global equivalent surface layer (GEL) of ~229 m, which can account for at least some of the surface features on Mars attributed to flowing water and may be sufficient to support the past presence of a shallow sea on Mars' surface.     

THERMAP: a mid-infrared spectro-imager for space missions to small bodies in the inner solar system

We present THERMAP, a mid-infrared spectro-imager for space missions to small bodies in the inner solar system, developed in the framework of the MarcoPolo-R asteroid sample return mission. THERMAP is very well suited to characterize the surface thermal environment of a NEO and to map its surface composition. The instrument has two channels, one for imaging and one for spectroscopy: it is both a thermal camera with full 2D imaging capabilities and a slit spectrometer. THERMAP takes advantage of the recent technological developments of uncooled microbolometer arrays, sensitive in the mid-infrared spectral range. THERMAP can acquire thermal images (8–18 μm) of the surface and perform absolute temperature measurements with a precision better than 3.5 K above 200 K. THERMAP can acquire mid-infrared spectra (8–16 μm) of the surface with a spectral resolution Δλ of 0.3 μm. For surface temperatures above 350 K, spectra have a signal-to-noise ratio >60 in the spectral range 9–13 μm where most emission features occur.     

Effect of polychromatic X‐ray microtomography imaging on the amino acid content of the Murchison CM chondrite

X‐ray microcomputed tomography (μCT) is a useful means of characterizing cosmochemical samples such as meteorites or robotically returned samples. However, there are occasional concerns that the use of μCT may be detrimental to the organic components of a chondrite. Small organic compounds such as amino acids comprise up to ~10% of the total solvent extractable carbon in CM carbonaceous chondrites. We irradiated three samples of the Murchison CM carbonaceous chondrite under conditions akin to and harsher than those typically used during typical benchtop X‐ray μCT imaging experiments to determine if detectable changes in the amino acid abundance and distribution relative to a nonexposed Murchison control sample occurred. After subjecting three meteorite samples to ionizing radiation dosages between ~300 Gray (Gy) and 3 kGy with bremstrahlung X‐rays, we analyzed the amino acid content of each sample. Within sampling and analytical errors, we cannot discern differences in the amino acid abundances and amino acid enantiomeric ratios when comparing the control samples (nonexposed Murchison) and the irradiated samples. We conclude that a polychromatic X‐ray μCT experiment does not alter the abundances of amino acids to a degree greater than how well those abundances are measured with our techniques and therefore any damage to amino acids is minimal.     

The Red Edge Problem in asteroid band parameter analysis

Near‐infrared reflectance spectra of S‐type asteroids contain two absorptions at 1 and 2 μm (band I and II) that are diagnostic of mineralogy. A parameterization of these two bands is frequently employed to determine the mineralogy of S(IV) asteroids through the use of ordinary chondrite calibration equations that link the mineralogy to band parameters. The most widely used calibration study uses a Band II terminal wavelength point (red edge) at 2.50 μm. However, due to the limitations of the NIR detectors on prominent telescopes used in asteroid research, spectral data for asteroids are typically only reliable out to 2.45 μm. We refer to this discrepancy as “The Red Edge Problem.” In this report, we evaluate the associated errors for measured band area ratios (BAR = Area BII/BI) and calculated relative abundance measurements. We find that the Red Edge Problem is often not the dominant source of error for the observationally limited red edge set at 2.45 μm, but it frequently is for a red edge set at 2.40 μm. The error, however, is one sided and therefore systematic. As such, we provide equations to adjust measured BARs to values with a different red edge definition. We also provide new ol/(ol+px) calibration equations for red edges set at 2.40 and 2.45 μm.     

Micromega/IR: Design and status of a near-infrared spectral microscope for in situ analysis of Mars samples

MicrOmega is an ultra miniaturized spectral microscope for in situ analysis of samples. It is composed of 2 microscopes; one with a spatial sampling less or equal to 4 μm, working in 4 colors in the visible range: MicrOmega/VIS, and a NIR hyperspectral microscope working in the spectral range 0.9–4 μm with a spatial sampling of 20 μm per pixel: MicrOmega/IR (described in this paper). MicrOmega/IR illuminates and images samples a few mm in size and acquires the NIR spectrum of each resolved pixel in up to 320 contiguous spectral channels. The goal of this instrument is to analyze in situ the composition of collected samples at almost their grain size scale, in a non-destructive way. With the chosen spectral range and resolution, a wide variety of constituents can be identified: minerals, such as pyroxene and olivine, ferric oxides, hydrated phyllosilicates, sulfates and carbonates and ices and organics. The composition of the various phases within a given sample is a critical record of its formation and evolution. Coupled to the mapping information, it provides unique clues to describe the history of the parent body (planet, satellite and small body). In particular, the capability to identify hydrated grains and to characterize their adjacent phases has a huge potential in the search for possible bio-relics.     

Titan's 5-micron lightcurve

We report on repeated mid-resolution (R∼2000) spectroscopic observations of Titan, acquired between November 2002 and January 2003 with ISAAC at the ESO/VLT and covering the 4.84-5.05 μm range. These observations, which sample four different positions of Titan around Saturn, clearly indicate a variability of the 5-μm continuum albedo, with Titan's geometric albedo decreasing by ∼40% from Titan's leading side to the trailing side. This Titan 5-μm “lightcurve” appears to be in phase with the other near-infrared lightcurves. This can be understood in terms of a surface model in which water ice coexists in minor and variable proportions (13-25%, if pure) with a second, dark, component.     

Spectral reflectance properties of carbonaceous chondrites: 6. CV chondrites

Multiple reflectance spectra of 11 CV chondrites have been measured to determine spectral–compositional relationships for this meteorite class and to aid the search for CV parent bodies. The reflectance of CV chondrite spectra is variable, ranging from ～5% to 13% at 0.56 μm, and ～5% to 15% at the 0.7 μm region local reflectance maximum. Overall slopes range from slightly blue to red for powders, while slab spectra are strongly blue-sloped. With increasing average grain size and/or removal of the finest fraction, CV spectra generally become more blue-sloped. CV spectra are characterized by ubiquitous absorption features in the 1 and 2 μm regions. The 1 μm region is usually characterized by a band centered near 1.05–1.08 μm and a band or shoulder near 1.3 μm that are characteristic of Fe-rich olivine. Band depths in the 1 μm region for powdered CVs and slabs range from ～1% to 10%. The 2 μm region is characterized by a region of broad absorption that extends beyond 2 μm and usually includes band minima near 1.95 and 2.1 μm; these features are characteristic of Fe²⁺-bearing spinel. The sample suite is not comprehensive enough to firmly establish whether spectral differences exist between CV_R, CV_OxA, and CV_OxB subclasses, or as a function of metamorphic grade. However, we believe that the mineralogic and petrologic differences that exist between these classes, and with varying petrologic subtype (CV3.0–>3.7), may not be significant enough to result in measurable spectral differences that exceed spectral variations within a subgroup, within an individual meteorite, or as a function of grain size. Terrestrial weathering seems to affect CV spectra most noticeably in the visible region, resulting in more red-sloped spectra for finds as compared to falls. The search for CV parent bodies should focus on the detection of olivine and spinel absorption bands, specifically absorption features near 1.05, 1.3, 1.95, and 2.1 μm, as these are the most commonly seen spectral features of CV chondrites.     

Asteroids (65) Cybele, (107) Camilla and (121) Hermione: Infrared spectral diversity among the Cybeles

We find a clear diversity in the 3 μm and 10 μm features of three Cybele asteroids: (107) Camilla, (121) Hermione, and (65) Cybele. (121) Hermione exhibits a “check-like” 3 μm feature, which may be attributed to OH-dominated minerals and (107) Camilla shows a rounded “bowl” like feature closer to that of (65) Cybele, which may be attributed to H₂O-dominated minerals. The 10 μm features of these three asteroids are also different from each other.     

Spectroscopic survey of M-type asteroids

M-type asteroids, as defined in the Tholen taxonomy (Tholen, D.J. [1984]. Asteroid Taxonomy from Cluster Analysis of Photometry. Ph.D. Dissertation, University of Arizona, Tucson), are medium albedo bodies supposed to have a metallic composition and to be the progenitors both of differentiated iron–nickel meteorites and enstatite chondrites. We carried out a spectroscopic survey in the visible and near infrared wavelength range (0.4–2.5 μm) of 30 asteroids chosen from the population of asteroids initially classified as Tholen M-types, aiming to investigate their surface composition. The data were obtained during several observing runs during the years 2004–2007 at the TNG, NTT, and IRTF telescopes. We computed the spectral slopes in several wavelength ranges for each observed asteroid, and we searched for diagnostic spectral features. We confirm a large variety of spectral behaviors for these objects as their spectra are extended into the near infrared, including the identification of weak absorption bands, mainly of the 0.9 μm band tentatively attributed to orthopyroxene, and of the 0.43 μm band that may be associated to chlorites and Mg-rich serpentines or pyroxene minerals such us pigeonite or augite. A comparison with previously published data indicates that the surfaces of several asteroids belonging to the M-class may vary significantly.We attempt to constrain the asteroid surface compositions of our sample by looking for meteorite spectral analogs in the RELAB database and by modeling with geographical mixtures of selected meteorites/minerals. We confirm that iron meteorites, pallasites, and enstatite chondrites are the best matches to most objects in our sample, as suggested for M-type asteroids. For 22 Kalliope, we demonstrate that a synthetic mixture obtained enriching a pallasite meteorite with small amounts (1–2%) of silicates well reproduce the spectral behavior including the observed 0.9 μm feature.The presence of subtle absorption features on several asteroids confirms that not all objects defined by the Tholen M-class have a pure metallic composition.A statistical analysis of spectral slope distribution vs. orbital parameters shows that our sample originally defined as Tholen M-types tend to be dark in albedo and red in slope for increasing value of the semi-major axis. However, we note that our sample is statistically limited by our number of objects (30) and slightly varying results are found for different subsets. If confirmed, the albedo and slope trends could be due to a difference in composition of objects belonging to the outer main belt, or alternatively to a combination of surface composition, grain size and space weathering effects.     

Further characterization of carbonaceous materials in Hayabusa‐returned samples to understand their origin

Carbonaceous materials in the sample catcher of the Hayabusa spacecraft were assigned as category 3 particles. We investigated the category 3 particles with a suite of in situ microanalytical methods. Possible contaminants collected from the cleanrooms of the spacecraft assembly and extraterrestrial sample curation center (ESCuC) were also analyzed in the same manner as category 3 particles for comparison. Our data were integrated with those of the preliminary examination team for category 3 particles. Possible origins for the category 3 particles include contamination before and after the operation of the Hayabusa spacecraft.     

Large spinel grains in a CM chondrite (Acfer 331): Implications for reconstructions of ancient meteorite fluxes

By dissolving 30–400 kg of marine limestone in HCl and HF acid, our group has previously recovered common relict chromite grains (approximately 63–250 μm) from ordinary chondritic micrometeorites that fell on ancient sea floors, up to 500 Myr old. Here, we evaluate if CM group carbonaceous chondritic material, which makes up an important fraction of the micrometeorite flux today, contains analogous grains that can be searched for in acid residues. We dissolved 8 g of CM2 meteorite Acfer 331 in HF, which yielded a characteristic assemblage of both transparent Mg‐Al‐ and opaque Cr‐spinels >28 μm. We find on average 4.6 and 130 Mg‐Al‐spinel grains per gram in the 63–250 and 28–63 μm size fractions, respectively. These grains are mostly pink or colorless, and often characterized by heterogeneous Cr‐content. Black, opaque Cr‐spinel grains are absent from the >63 μm fraction, but in the 28–63 μm fraction we find approximately 65 such grains per gram meteorite. The individual grains have a characteristic composition, with heterogeneous major element compositions (e.g., 44.4–61.7 wt% Cr₂O₃), but narrow ranges for maximum TiO₂ (0.6–1.6 wt%) and V₂O₃ (0.5–1.0 wt%) concentrations. The content of spinel grains in the 28–63 μm fraction of CM meteorites appears comparable at the order of magnitude level with the content of >63 μm sized chromite grains in fossil L‐chondrites from Ordovician limestone. Our approach of recovering meteoritic spinel from sediment may thus be extended to include CM meteorites, but the smaller size fraction of the acid residues should be searched.     

The mid-infrared spectrum of the zodiacal and exozodiacal light

The zodiacal light is the dominant source of the mid-infrared sky brightness seen from Earth, and exozodiacal light is the dominant emission from planetary and debris systems around other stars. We observed the zodiacal light spectrum with the mid-infrared camera ISOCAM over the wavelength range 5-16 μm and a wide range of orientations relative to the Sun (solar elongations 68°-113°) and the ecliptic (plane to pole). The temperature in the ecliptic ranged from 269 K at solar elongation 68° to 244 K at 113°, and the polar temperature, characteristic of dust 1 AU from the Sun, is 274 K. The observed temperature is exactly as expected for large (>10 μm radius), low-albedo (<0.08), rapidly-rotating, gray particles 1 AU from the Sun. Smaller particles (<10 μm radius) radiate inefficiently in the infrared and are warmer than observed. We present theoretical models for a wide range of particle size distributions and compositions; it is evident that the zodiacal light is produced by particles in the 10-100 μm radius range. In addition to the continuum, we detect a weak excess in the 9-11 μm range, with an amplitude of 6% of the continuum. The shape of the feature can be matched by a mixture of silicates: amorphous forsterite/olivine provides most of the continuum and some of the 9-11 μm silicate feature, dirty crystalline olivine provides the red wing of the silicate feature (and a bump at 11.35 μm), and a hydrous silicate (montmorillonite) provides the blue wing of the silicate feature. The presence of hydrous silicate suggests the parent bodies of those particles were formed in the inner solar nebula. Large particles dominate the size distribution, but at least some small particles (radii ∼1 μm) are required to produce the silicate emission feature. The strength of the feature may vary spatially, with the strongest features being at the lowest solar elongations as well as at high ecliptic latitudes; if confirmed, this would imply that the dust properties change such that dust further from the Sun has a weaker silicate feature. To compare the properties of zodiacal dust to dust around other main sequence stars, we reanalyzed the exozodiacal light spectrum for β Pic to derive the shape of its silicate feature. The zodiacal and exozodiacal spectra are very different. The exozodiacal spectra are dominated by cold dust, with emission peaking in the far-infrared, while the zodiacal spectrum peaks around 20 μm. We removed the debris disk continuum from the spectra by fitting a blackbody with a different temperature for each aperture (ranging from 3.7″ to 27″); the resulting silicate spectra for β Pic are identical for all apertures, indicating that the silicate feature arises close to the star. The shape of the silicate feature from β Pic is nearly identical to that derived from the ISO spectrum of 51 Oph; both exozodiacal features are very different from that of the zodiacal light. The exozodiacal features are roughly triangular, peaking at 10.3 μm, while the zodiacal feature is more boxy, indicating a different mineralogy.     

Multiwavelength study of 230 IRAS FSC galaxies

A sample of 230 galaxies has been compiled based on their IRAS FSC fluxes to study their multiwavelength properties and carry out comparative analyses with other similar samples. To understand the nature of these galaxies, a comparison with a sample of bright ULIRGs having fluxes at 60 μm fν > 1 Jy and 14 optically faint IRAS FSC galaxies is presented. This comparison shows that galaxies found by IRAS are not always strong infrared sources and that the objects from the sample of ULIRGs represent a sample of extreme galaxies, which are very powerful infrared sources. We have confirmed the consistency between Star Formation Rates (SFRs) calibrated based on luminosities of the PAH feature at 7.7 μm and radio 1.4 GHz flux densities. We have estimated the extinction for our 230 objects using SFRs calibrated from the PAH feature compared to ultraviolet flux, which shows that only 1% of the ultraviolet continuum typically escapes extinction by dust within a starburst.