共查询到20条相似文献,搜索用时 15 毫秒
1.
This paper presents results from a full scale decay test made with a tanker in a relatively protected area in the Brazilian coast. In at least two tests the environmental loads (wind, waves and current) were very small and the time history of the surge motion was well behaved, making it possible to check some proposed models for the damping in the hull and mooring lines. Field data seem to confirm that the damping is indeed of the fluid viscosity type and the theoretical models are able to recover roughly 75% of the observed damping, the energy dissipation in the mooring lines being, by far, the major contribution. The remaining 25% are likely due to non modeled effects, such as the environment influence, which although small and not measured certainly exists, and to the friction between the mooring lines and the seabed. 相似文献
2.
阐述了锚泊阻尼定义以及当前各种研究方法,选取一组用于实际工程中的锚泊线参数.通过改变预张力、振幅、振荡频率、轴向刚度、法向拖曳力系数和表面流速等参数,研究各参数对锚泊水平阻尼及垂向阻尼的影响.为使研究一般化,文中锚泊阻尼以及预张力等参数采取无量纲形式. 相似文献
3.
With the floating structures pushing their activities to the ultra-deep water,model tests have presented a challenge due to the limitation of the existing wave basins.Therefore,the concept of truncated mooring system is implemented to replace the full depth mooring system in the model tests,which aims to have the same dynamic responses as the full depth system.The truncated mooring system plays such a significant role that extra attention should be paid to the mooring systems with large truncation factor.Three different types of large truncation factor mooring system are being employed in the simulations,including the homogenously truncated mooring system,non-homogenously truncated mooring system and simplified truncated mooring system.A catenary moored semi-submersible operating at 1000 m water depth is presented.In addition,truncated mooring systems are proposed at the truncated water depth of 200 m.In order to explore the applicability of these truncated mooring systems,numerical simulations of the platform’s surge free decay interacting with three different styles of truncated mooring systems are studied in calm water.Furthermore,the mooring-induced damping of the truncated mooring systems is simulated in the regular wave.Finally,the platform motion responses and mooring line dynamics are simulated in irregular wave.All these simulations are implemented by employing full time domain coupled dynamic analysis,and the results are compared with those of the full depth simulations in the same cases.The results show that the mooring-induced damping plays a significant role in platform motion responses,and all truncated mooring systems are suitable for model tests with appropriate truncated mooring line diameters.However,a large diameter is needed for simplified truncated mooring lines.The suggestions are given to the selection of truncated mooring system for different situations as well as to the truncated mooring design criteria. 相似文献
4.
A computer program is developed for hull/mooring/riser coupled dynamic analysis of a tanker-based turret-moored FPSO (Floating Production Storage and Offloading) in waves, winds, and currents. In this computer program, the floating body is modeled as a rigid body with six degrees of freedom. The first- and second-order wave forces, added mass, and radiation damping at various yaw angles are calculated from the second-order diffraction/radiation panel program WAMIT. The wind and current forces for various yaw angles of FPSO are modeled following the empirical method suggested by OCIMF (Oil Company International Marine Forum). The mooring/riser dynamics are modeled using a rod theory and finite element method (FEM), with the governing equations described in a generalized coordinate system. The dynamics of hull, mooring lines, and risers are solved simultaneously at each time step in a combined matrix for the specified connection condition. For illustration, semi-taut chain-steel wire-chain mooring lines and steel catenary risers are employed and their effects on global FPSO hull motions are investigated. To better understand the physics related to the motion characteristics of a turret-moored FPSO, the role of various hydrodynamic contributions is analyzed and assessed including the effects of hull and mooring/riser viscous damping, second-order difference-frequency wave-force quadratic transfer functions, and yaw-angle dependent wave forces and hydrodynamic coefficients. To see the effects of hull and mooring/riser coupling and mooring/riser damping more clearly, the case with no drag forces on those slender members is also investigated. The numerical results are compared with MARIN's wave basin experiments. 相似文献
5.
针对圆筒型海上储油装置FPSO垂荡运动性能较差、无法安装干式井口的问题,设计了带延伸筒体与矩形阻尼结构的圆筒型FPSO,根据延伸筒体与矩形阻尼结构是否通海分为两种型式。建立水动力计算模型,比较分析不同延伸筒体和阻尼结构型式对FPSO水动力性能的影响。针对南海作业海域,设计了悬链式系泊系统,基于JONSWAP波浪谱对FPSO的运动进行时域预报,并对系泊系统进行校核。分析结果表明:通海型FPSO垂荡固有周期显著提升,可以错开南海百年一遇谱峰周期,通海型FPSO满足钻井、安装干式井口的运动响应要求,系泊系统系缆张力满足规范要求。 相似文献
6.
The responses of a spar constrained by slack mooring lines to steep ocean waves and tensions in the mooring lines are simulated using two different numerical schemes: a quasi-static approach (SMACOS) and a coupled dynamic approach (COUPLE). The two approaches are the same in computing wave loads on the structure. Their difference is in modeling dynamic forces of mooring lines; that is the dynamic forces are included in the computation of COUPLE but neglected in SMACOS. The numerical simulation is examined against the laboratory measurements of the JIP Spar in a water depth of 318 m. The dynamic coupling effects between the JIP Spar and its mooring lines in different water depths (318, 618 and 1018 m) are investigated by the comparison of numerical simulations obtained using the quasi-static and coupled dynamic approaches. It is found that the damping of mooring lines reduces the slow-drift surge and pitch of the Spar, especially in deep water. The reduction in the amplitude of slow-drift surge can reach about 10% in a water depth of 1018 m. The tension in mooring lines may greatly increase in the wave frequency range when dynamic forces in mooring lines are considered. The mooring-line tension in the wave frequency range predicted by the coupled dynamic approach can be eight times as great as the corresponding prediction by the quasi-static approach in a water depth of 1018 m. This finding may have important implications for the estimation of the fatigue strength and life span of the mooring lines deployed in deep water oceans. 相似文献
7.
The dynamic response of the mooring line will be a dominant factor to consider in their use for the station keeping of a wave energy converter (WEC). Due to the relatively small size of WECs and their being moored in relatively shallow waters the effect of waves, tide and current can be of greater significance than for other floating offshore systems. Axial line stretching and high-frequency ‘top-end’ dynamics can importantly modify damping and top-end loading.If a ‘farm’ of devices is to be considered then limitations in sea space may necessitate that the devices be relatively densely packed. This will mean that the ‘footprint’ of the mooring should be constrained, to ensure that the moorings from each device do not interfere and this will have great significance for the loading experienced by the line. One must also consider how the mooring system might change the response of the WEC and so alter its ability to extract power from the waves. Unlike a typical offshore system, the design of moorings for a WEC device must consider reliability and survivability, and the need to ensure efficient energy conversion.The design and operation of a chain mooring for a WEC is considered here. Generic experimental measurements of mooring line damping were conducted in the Heriot-Watt University wave basin at a scale of 1:10. The measurements were conducted on a single mooring line for surge motions and include the study of axial stretching and high top-end dynamics. The laboratory procedures were designed to resemble tests undertaken earlier at ‘full’ scale in 24 m water depth. The measurements were also compared with numerical studies. The experimental findings for WEC devices, supports the conclusion that dynamic mooring line motion will be an important variable, needing to be considered carefully within the design. 相似文献
8.
The motion response prediction of offshore structures may be carried out using time domain or frequency domain models or model tests. The frequency domain analysis uses the simplified, linearised form of the motion equations and it is very economical. The time domain analysis, unlike frequency domain models, is adequate to deal with non-linearities such as viscous damping and mooring forces, but it requires sophisticated solution techniques and it is expensive to employ. For moored semisubmersibles time domain techniques must be employed since there are strong nonlinearities in the system due to mooring line stiffness and damping and viscous drag forces. In the first part of this paper a time domain model to predict the dynamic response of a semi-submersibles are developed and the effect of thrusters and mooring line damping are incorporated into the time domain model. In the second part time domain simulations are carried out to find the total extreme motions and mooring forces. 相似文献
9.
Based on the theory of impact dynamics, the motion equations for a mooring line-floating body system before and after impact loading are established with consideration of the viscoelastic property of mooring lines. The factors that influence the taut-slack conditions of a mooring system are analyzed through classifying the taut-slack regions, which are defined by non-dimensional ratios of displacement, frequency, and damping of the system. The mooring system of Jip spar platform is analyzed, and the snap te... 相似文献
10.
The dynamic analysis of a deepwater floating structure is complicated by the fact that there can be significant coupling between the dynamics of the floating vessel and the attached risers and mooring lines. Furthermore, there are significant nonlinear effects, such as geometric nonlinearities, drag forces, and second order (slow drift) forces on the vessel, and for this reason the governing equations of motion are normally solved in the time domain. This approach is computationally intensive, and the aim of the present work is to develop and validate a more efficient linearized frequency domain approach. To this end, both time and frequency domain models of a coupled vessel/riser/mooring system are developed, which each incorporate both first and second order motions. It is shown that the frequency domain approach yields very good predictions of the system response when benchmarked against the time domain analysis, and the reasons for this are discussed. It is found that the linearization scheme employed for the drag forces on the risers and mooring lines yields a very good estimate of the resulting contribution to slow drift damping. 相似文献
11.
A point-absorber-type Wave-Energy Converter (WEC) consisting of a floating vertical inner cylinder and an annular outer cylinder that slides along the inner one is considered. The two cylinders heave differently under wave excitation, and wave energy can be harnessed from the relative heave motion between the two cylinders using a Permanent Magnet Linear Generator (PMLG) as the Power Take-Off unit. A mooring cable is attached to the bottom of the inner cylinder. This paper aims to examine the effect of the stiffness of the mooring cable on the performance of the coaxial-cylinder WEC system. The two limiting cases of no mooring cable (freely floating inner and outer cylinders) and an infinitely stiff mooring cable (fixed inner cylinder) were also considered. To perform the analysis, hydrodynamic and interference coefficients of the two heaving cylinders were computed semi-analytically using the method of matched eigenfunction expansions. Experimentally determined viscous corrections on damping were also included in the model in order to have more realistic predictions. The performance of the system in terms of motion responses and capture width were predicted and discussed for both regular and irregular waves. The results of the analysis indicate that both the freely floating design and the design with rigidly moored inner cylinder are viable. The two limiting cases show similar optimal performances, albeit with very different optimal generator damping. However, an ill-chosen mooring-cable stiffness may cause the inner and the outer cylinders to have the same resonance frequency, eliminating the relative heave motion and leading to almost no energy extraction. This situation needs to be avoided when designing the mooring system for a coaxial-cylinder WEC. 相似文献
12.
A design of semi-submersible platform is mainly based on the extreme response analysis due to the forces experienced by the components during lifetime. The external loads can induce the extreme air gap response and potential deck impact to the semi-submersible platform. It is important to predict air gap response of platforms accurately in order to check the strength of local structures which withstand the wave slamming due to negative air gap. The wind load cannot be simulated easily by model test in towing tank whereas it can be simulated accurately in wind tunnel test. Furthermore, full scale simulation of the mooring system in model test is still a tuff work especially the stiffness of the mooring system. Owing to the above mentioned problem, the model test results are not accurate enough for air gap evaluation. The aim of this paper is to present sensitivity analysis results of air gap motion with respect to the mooring system and wind load for the design of semi-submersible platform. Though the model test results are not suitable for the direct evaluation of air gap, they can be used as a good basis for tuning the radiation damping and viscous drag in numerical simulation. In the presented design example, a numerical model is tuned and validated by ANSYS AQWA based on the model test results with a simple 4 line symmetrical horizontal soft mooring system. According to the tuned numerical model, sensitivity analysis studies of air gap motion with respect to the mooring system and wind load are performed in time domain. Three mooring systems and five simulation cases about the presented platform are simulated based on the results of wind tunnel tests and sea-keeping tests. The sensitivity analysis results are valuable for the floating platform design. 相似文献
13.
Hybrid model testing technique is widely used in verification of a deepwater floating structure and its mooring system,but the design of the truncated mooring systems which can reproduce both static and dynamic response same as the full-depth mooring system is still a big challenge,especially for the mooting systems with large truncation.A Cell-Tress Spar operated in 1500 m water depth is verified in a wave basin with 4 m water depth.A large truncation factor arises even though a small model scale 1:100 is adopted.Computer program modules for analyzing the static and frequency domain dynamic response of mooting line are combined with multi-objective genetic algorithm NSGA-II to optimize the truncared mooting system.Considering the asymmetry of layout of mooring hnes,two different truncated mooring systems are respectively designed for both directions in which the restoring forces of the.mooting system are quite,different.Not only the static characteristics of the mooting systems are calibrated,but also the dynamic responses of the single truncated mooting line are evaluated through time domain numerical simulation and model tests.The model test results of 100-year storm in the GOM are reconstructed and extrapolated to a full depth.It is found that the experimental and numerical resuits of Spar wave frequency motion agree well,and the dynamic responses of the full-depth mooring lines are better reproduced,but the low frequency surge motion is overestimated due to the smaller mooring-induced damping.It is a feasible method adopting different truncated mooring systems for different directions in which the restoring force characteristics are quite different and cannot be simulated by one truncated mooring system.Hybrid verification of a deepwater platform in wave basin with shallow water depth is still feasible if the truncated mooring systems are properly designed,and numerical extrapolation is necessary. 相似文献
14.
基于三维频域势流理论,计算船体的水动力参数;采用动态耦合方法分析了深海半潜式生产平台各系统之间的相互作用特征,研究了立管系统对锚泊系统定位能力的影响。计算结果表明,立管系统在一定程度上增加了整个系统的刚度,其所受的附加质量和阻尼可降低平台的低频响应,从而降低平台的偏移和系泊缆的张力;海流将增大立管上的拖曳力,使平台偏移更远,锚索上的张力更大;立管系统对锚泊系统定位性能的最终影响需综合考虑多种因素的叠加。对目标平台而言,由于服役海域的流速较大,对立管的拖曳作用较为明显。因此,为确保平台的安全性,当服役海域流速较大时,带有多立管的平台,其锚泊系统的设计应考虑立管的影响。 相似文献
15.
The drag-induced damping in a mooring cable due to combined first- and second-order wave excited motion of a moored vessel has been determined by statistical linearisation. A dynamic stiffness approach developed elsewhere is used to deal with the dynamics of the mooring cables. The power spectral densities of low- and wave-frequency responses are obtained which clearly show the influence of mooring line damping. The non-Gaussian probability density functions (pdf) and expected crossing rates of vessel responses and dynamic cable tensions are determined using the Kac–Seigert technique, and the influence of drag damping is highlighted. 相似文献
16.
首先介绍全球海域圆筒形装置的工程应用案例,对比圆筒形FPSO相对常规船形的优势,然后以原油储量、工艺模块甲板面积、耐波性、稳性、系泊系统、排水量等控制参数为目标,研究圆筒形FPSO主尺度选取依据,分舱原则。重点研究圆筒形装置的阻尼板结构,此为抑制运动响应的关键结构,通过模型试验方法分析对比了水平阻尼板、不同角度锥形阻尼板的特性。最后研究圆筒形装置运动性能分析方法,介绍二阶响应数值预报方法,研究垂荡和横摇运动的耦合效应,分析波频和低频运动响应,通过模型试验进行了验证,从而指导圆筒形装置设计。 相似文献
17.
Developments in the study of wave forces and construction techniques in deep water by the offshore oil industry have increased the use of marine terminals at deep water locations. A thorough understanding of moored ship dynamics when subjected to waves, wind and current combined with the use of flexible mooring lines would help to design berthing terminals for exposed areas. In this paper, the three dimensional problem of wave interactions with a barge moored to a single point is dealt with, based on the finite element method. The effect of flexibility of the mooring line and the point of mooring on the response of the barge as well as the mooring line tension is investigated. The paper compares the numerical results with model tests carried out on a barge moored to a fixed support under regular and random waves in head sea. The effect of stiffness of the mooring line on the barge response for different mooring points is discussed, which would be useful for the designers. The effect of viscous damping is also considered. The analytical results are in good agreement with the experimental results in both regular and random waves. 相似文献
18.
The two-dimensional problem of wave transformation by, and motions of, moored floating objects is solved numerically as a boundary value problem by direct use of Green's identity formula for a potential function. The cross-sectional shape of the floating object, the bottom configuration and the mooring arrangements may be all arbitrary. For a given incident wave, the three modes of body motion, the wave system and mooring forces are all solved at the same time. A laboratory experiment is conducted to verify the theory. Generally good agreements between the theory and experiments are obtained as long as the viscous damping due to flow separation is small. A numerical experiment indicates that a conventional sluck mooring is to worsen the wave attenuation by a floating breakwater and that a properly arranged elastic mooring can considerably improve the wave attenuation by a floating breakwater. 相似文献
19.
由于聚酯缆绳具备优异的力学性能,促使以其为主体系缆的绷紧式系泊系统得以广泛应用和发展。但聚酯系缆具有复杂的黏弹性和黏塑性,且由于在安装和使用过程中可能产生不同程度的损伤,使得聚酯系缆的动刚度特性发生演变,从而对系泊系统的动力响应产生直接影响。以一系泊于1 020 m水深的Spar平台为例,运用ABAQUS软件建立了由聚酯缆绳组成的系泊系统有限元模型,并利用ABAQUS子程序将损伤缆绳动刚度经验公式进行导入计算,以更好地反映系缆真实的动刚度变化。基于该有限元模型,计算了在相同水流、波浪工况下,不同损伤度、不同损伤系缆的系缆张力历程和平台的横荡、纵荡位移响应,分析了不同损伤度、不同损伤系缆对系缆张力及平台位移的影响。这些成果对把握绷紧式系泊系统在聚酯系缆有损伤情况下的非线性动力响应及其安全应用具有重要的参考价值。 相似文献
20.
移动式海洋平台锚泊系统通常用锚索或锚链等多种成分合成的锚泊线,因而涉及参数较多给设计分析带来不便。针对这一问题,基于准静定方法推导限定水深下多成分锚泊线悬链线方程,并考虑锚泊线组成成分的参数对锚泊系统回复力的影响,建立目标函数最小化的多成分锚泊线优化设计模型。采用遗传算法对南海2号锚泊系统的改造进行分析求解,得到有益的结论。 相似文献
|