Effect of wetting–drying cycles on swelling behavior of lime stabilized sand–bentonite mixtures

In the present study, influence of wetting–drying cycles on swelling pressures of sand–bentonite mixtures used in the construction of sanitary landfills to have an impermeable liner was investigated before and after lime treatment of the mixtures. Swelling pressure tests were conducted to see if the swelling pressures were affected by wetting–drying cycles. First series of specimens were prepared as a mixture of sand and bentonite only. In the first series of specimens, sand was mixed with bentonite in various proportions with their optimum water contents and compacted by using standard proctor energy. In the second series of the specimens, lime in various proportions was added to the mixtures of sand–bentonite. Then, the sand–bentonite mixtures stabilized by lime were compacted with the standard proctor energy at their optimum moisture contents. Five wetting–drying cycles were performed on each specimen and values of swelling pressures were measured at the end of each cycle. Results of swelling pressure tests indicated that the swelling pressure is decreased when lime is added to the mixtures. In addition, decrements were observed on swelling pressures by wetting–drying cycles. The results of the experiments of this investigation showed that the beneficial effect of lime stabilization to control the swelling pressures was partly lost by the wetting–drying cycles. However, the test results indicated that the swelling pressures of the specimens made of sand–bentonite mixtures stabilized by lime were lower than the swelling pressures of the specimens made of only sand–bentonite mixtures.     

Impact of pore fluid chemistry on the thermal conductivity of bentonite–sand mixture

Thermal conductivity is an important parameter to consider when designing clay-based barriers for use in deep geological repositories (DGR). In the DGR environment, the infiltration of local saline groundwater can potentially change the pore fluid chemistry of a barrier over its lifetime. This change in chemistry is known to alter the thermal properties of the barrier materials. In order to examine the impact of pore fluid salinity on thermal conductivity, experiments were conducted under both distilled water and saline pore fluid conditions. The material mixtures were prepared at two different dry densities using two different salt types. Furthermore, five different thermal conductivity prediction models were selected and evaluated on their performance with respect to the experimental outcomes. In general, these results indicated that an increase in the constituent pore fluid’s salt concentration leads to a decrease in the thermal conductivity of the material. Additionally, the thermal conductivity values of the materials prepared at a high dry density were greater than of those compacted at a low dry density.     

Prediction of hydraulic conductivity for soil–bentonite mixture

Owing to its low hydraulic conductivity, soil and bentonite mixture is applied as a liner material. However, the experimental determination of hydraulic conductivity, which is controlled by various physical, chemical and mineralogical factors, requires an expensive and time-consuming setup. In the present work, multigene symbolic, genetic programming was used to model functional relationships for hydraulic conductivity. The developed model was able to generalize highly nonlinear variations in data as well as predict system behavior from experimental observations. It was found that the predictions obtained from developed model agree well with experimental observations.     

Influence of dry density and water salinity on the swelling pressure and hydraulic conductivity of compacted GMZ01 bentonite–sand mixtures

Acta Geotechnica - Compacted Gaomiaozi bentonite–sand mixtures are regarded as attractive buffer/backfill materials for nuclear waste deep geological disposal. When the mixture blocks are...     

Effect of sand grain size and boundary condition on the swelling behavior of bentonite–sand mixtures

Deep geological repository is a favorable choice for the long-term disposal of nuclear wastes. Bentonite–sand mixtures have been proposed as the potential engineered barrier materials because of their suitable swelling properties and good ability to seal under hydrated repository conditions. To investigate the effects of sand grain size on the engineering performance of bentonite–sand mixtures, we prepare five types of bentonite–sand mixtures by mixing bentonite with sand of varying particle size ranges (0.075–0.25 mm, 0.25–0.5 mm, 0.5–1 mm, 1–2 mm and 2–5 mm, respectively). We carry out sequential oedometer tests under different simulated repository conditions, including constant vertical stress (CVS), constant stiffness (CS) and constant volume (CV) conditions. The microstructural heterogeneity and anisotropy of these soil mixtures are characterized through the quantitative analysis of micro-CT scanning results. Experimental results reveal that both sand grain size and boundary condition significantly influence the swelling of soil mixtures. Under three conditions, the temporal evolutions of swelling stress and strain follow similar trends that they increase faster at the beginning and gradually stabilize afterward. Comparing the ultimate values, swelling strains follow CVS?>?CS?>?CV, while swelling stresses follow CV?>?CS?>?CVS. Under CS boundary conditions, as the stiffness coefficient increases, the swelling pressure increases and the swelling strain decreases. CT results further indicate that mixtures with larger sand inclusions are more structurally heterogeneous and anisotropic, resulting in increased inter-particle friction and collision and a higher energy dissipation during the swelling process. Moreover, the non-uniform distribution of bentonite in local zones would be intensified, which plays an important role in compromising swelling behavior. Therefore, soil samples mixed with larger sand particles present a smaller swelling stress and strain values. This study may guide the choice of engineered barrier materials toward an improved design and assessment of geological repository facilities.

     

Changes in strength,hydraulic conductivity and microstructure of superabsorbent polymer stabilized soil subjected to wetting–drying cycles

Acta Geotechnica - Superabsorbent polymers (SAPs) are environmentally friendly stabilizers to improve the engineering properties of excavated soils with high water contents. The present study aims...     

Effect of fines content and void ratio on the saturated hydraulic conductivity and undrained shear strength of sand–silt mixtures

The hydraulic conductivity represents an important indicator parameter in the generation and redistribution of excess pore pressure of sand–silt mixture soil deposits during earthquakes. This paper aims to determine the relationship between the undrained shear strength (liquefaction resistance) and the saturated hydraulic conductivity of the sand–silt mixtures and how much they are affected by the percentage of low plastic fines (finer than 0.074 mm) and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests carried out on samples reconstituted from Chlef river sand with 0, 10, 20, 30, 40, and 50 % non-plastic silt at an effective confining pressure of 100 kPa and two initial relative densities (D _r = 20, 91 %) are presented and discussed. It was found that the undrained shear strength (liquefaction resistance) can be correlated to the fines content, intergranular void ratio and saturated hydraulic conductivity. The results obtained from this study reveal that the saturated hydraulic conductivity (k _sat) of the sand mixed with 50 % low plastic fines can be, in average, four orders of magnitude smaller than that of the clean sand. The results show also that the global void ratio could not be used as a pertinent parameter to explain the undrained shear strength and saturated hydraulic conductivity response of the sand–silt mixtures.     

Modeling of the swelling–shrinkage behavior of expansive clays during wetting–drying cycles

Acta Geotechnica - This paper presents a constitutive model for simulating the swelling–shrinkage volume change of expansive soils during wetting–drying cycles. Based on the concept of...     

Swelling pressure–suction relationship of heavily compacted bentonite–sand mixtures

This paper presents results of an experimental work to determine a relationship between swelling pressure and suction of heavily compacted bentonite–sand mixtures. For comparison, tests were also carried out on heavily compacted bentonite specimens. A series of swelling pressure tests were performed using multi-step constant-volume method where suction of the specimens tested was reduced in a stepwise manner toward a zero value. The suction reduction was induced using vapor equilibrium and axis-translation techniques. It is shown that compacted specimens did not exhibit any collapse upon suction decrease and exhibited maximum swelling pressures at zero-equilibrium suction. The development of swelling pressure with decreasing suction of the specimens showed threshold suctions below which a further reduction in suction yields an increase in the swelling pressure of the same magnitude. The magnitude of threshold suction was found to be a function of bentonite content in compacted specimens.     

Experimental investigations of the soil water retention curve under multiple drying–wetting cycles

Acta Geotechnica - Natural soils usually experience multiple drying and wetting cycles in geotechnical engineering. In this paper, the influences of history of drying and wetting upon the...     

A compression model for sand–silt mixtures based on the concept of active and inactive voids

A compression model for sand–silt mixtures is needed in geotechnical engineering, for example in the analysis and prediction of deformation of levees and embankments due to internal erosion. In this paper, we introduce a novel concept of dividing the voids of a granular material into two hypothetical fractions: active and inactive voids. The active voids are kinematically available to the compression process. The inactive voids are kinematically unavailable to the compression process. The volume of active voids is dependent on the initial density and effective stress level. The volume of inactive voids is dependent on the amount of fines in the mixture. The current paper considers 1-D and isotropic compression behavior of sand–silt mixtures at stress levels lower than 2 MPa, so no substantial particle breakage is expected to occur. To successfully predict the void ratio for a sand–silt mixture during compression loading, we need (1) a mathematical expression for the evolution of the active void ratio during compression and (2) a relationship between the inactive void ratio and fines content of the mixture. For sand–silt mixtures with any amount of fines, the proposed model requires five material parameters, which are determined from two compression tests, and four minimum void ratio tests on sand–silt mixtures with different fines content. The performance of the proposed model is verified for six different types of sand–silt mixture with various fines contents, by comparing the predicted void ratios with the measured data from the experiments. The comparisons show a good agreement between the predictions and the measured data and prove the suitability of the proposed model for the prediction of compressibility of sand–silt mixtures with any amount of fines.     

Thermo-hydro-mechanical process and damage mechanism of a cold-region canal under coupled wetting–drying and freezing–thawing cycles

Acta Geotechnica - In cold regions, periodic wetting–drying and freezing–thawing (WDFT) actions lead to frequent and heavy canal damage, weakening the water-conveyance capacities of...     

Microscale analysis to characterize effects of water content on the strength of cement-stabilized sand–clay mixtures

Acta Geotechnica - Cement stabilization is a useful and widely adopted method to improve the engineering properties of soils. However, characterization of the unconfined compressive strength, a...     

A laboratory study of the self sealing behaviour of a compacted sand–bentonite mixture

Bricks made of compacted sand–bentonite mixture are considered as a possible engineered barrier to isolate high-level radioactive waste at great depth. This work is aimed at investigating some specific effects related to the presence of discontinuities at the contact between the bricks and the excavation wall. In order to do this, an experimental device was developed in the laboratory. The model is made up of a specially designed infiltration cylinder which allows the precise definition of a planar discontinuity between the compacted specimen (a sand–bentonite mixture made up of sand and Kunigel clay from Japan) and a metal wall. During hydration and subsequent specimen swelling, the planar wall is filled, resulting in a healing process. Three total pressure gauges placed along the wall allow a detailed observation of the increase in total stress against the wall. After different periods of swelling, the maximum resistance of the specimen–wall interface to pressure was tested by imposing a pressure increase through a porous stone placed at one end of the cylinder. It was found that the maximum pressure supported by the interface is a function of the initial thickness of the discontinuity and the initial density of the specimen. It was also found that the maximum sustainable pressure depends linearly on the elapsed time. These results are of interest for optimizing water infiltration procedures in either mock-up tests or real disposal systems. If the maximum sustainable pressure at the interface is known, it is possible either to ensure homogeneous hydration of a mass of bricks by respecting the maximum injection pressure limit or to accelerate hydration by forcing water paths along the discontinuities.     

Global representation of the drying–wetting curves of four engineering soils: experiments and correlations

The main objective of this paper is to examine how different engineering soils react to environmental variations and to provide correlations to characterize their behaviour under null external mechanical stress. Two French and two Algerian soils with liquid limits ranging from 36 to 112 were prepared under both slurry and Proctor compaction conditions, and then subjected to drying–wetting paths with suction controlled from several kPa to several hundreds of MPa. Experimental results are presented in five diagrams to show globally and simultaneously the shrinkage–swelling, saturation–desaturation and water retention characteristics. A reasonable consistency was observed between the oedometric and drying curves of slurry, confirming the equivalence between hydraulic loading (suction) and mechanical loading (consolidation stress) on the volume change behaviour of different soils. As an intrinsic parameter of soil nature, liquid limit was found to have a significant influence on the shrinkage limit, air-entry suction and compressibility of both slurry and compacted samples. For that reason, correlations between these characteristics and liquid limit were set up, providing a good basis for a first estimation of the drying–wetting curves. At the micro-scale, new experimental results were obtained: either on drying or wetting path, the micro-pores were almost unaffected, whereas, when matrix suction increased from 0.1 to 8 MPa, the volume of macro-pores decreased to quasi-closure. At last, the analogy between the compaction and drying–wetting curves, and the comparison of different methods to determine the water retention curve were addressed. Such analogies and comparisons contribute to a better understanding of the mechanisms of mechanical stress and suction.     

Weakening laws of slip zone soils during wetting–drying cycles based on fractal theory: a case study in the Three Gorges Reservoir (China)

Acta Geotechnica - Slip zone soils play a crucial role in the evolution of landslides. In this paper, slip zone soils of the Huangtupo Landslide in the Three Gorges Reservoir area, which is an...     

A new generalized soil thermal conductivity model for sand–kaolin clay mixtures using thermo-time domain reflectometry probe test

As the demand of exploitation and utilization of geothermal energy increases, more geothermal-related earth structures occur recently. The design of the structures depends upon an accurate prediction of soil thermal conductivity. The existing soil thermal conductivity models were mostly developed by empirical fits to datasets of soil thermal conductivity measurements. Due to the gaps in measured thermal conductivities between any two tested natural soils, the models may not provide accurate prediction for other soils, and the predicted thermal conductivity might not be continuous over the entire range of soil type. In this research, a generalized soil thermal conductivity model was proposed based on a series of laboratory experiments on sand, kaolin clay and sand–kaolin clay mixtures using a newly designed thermo-time domain reflectometry probe. The model was then validated with respect to k _dry–n (thermal conductivity of dry soils and porosity) and k _r–S _r (normalized thermal conductivity and degree of saturation) relationships by comparing with previous experimental studies. The predicted thermal conductivities were found to be in a good agreement with the experimental data collected from both this study and the other literatures with at least 85% confidence interval. It is concluded that the proposed model accounts for the effects of both environmental factors (i.e., moisture content and dry density) and compositional factors (i.e., quartz content and soil type) on soil thermal conductivity, and it has a great potential in predicting soil thermal conductivity more accurately for geothermal applications.     

Electrical conductivity of the plagioclase–NaCl–water system and its implication for the high conductivity anomalies in the mid-lower crust of Tibet Plateau

In order to investigate the origin of the high conductivity anomalies geophysically observed in the mid-lower crust of Tibet Plateau, the electrical conductivity of plagioclase–NaCl–water system was measured at 1.2 GPa and 400–900 K. The relationship between electrical conductivity and temperature follows the Arrhenius law. The bulk conductivity increases with the fluid fraction and salinity, but is almost independent of temperature (activation enthalpy less than 0.1 eV). The conductivity of plagioclase–NaCl–water system is much lower than that of albite–NaCl–water system with similar fluid fraction and salinity, indicating a strong effect of the major mineral phase on the bulk conductivity of the brine-bearing system. The high conductivity anomalies of 10^?1 and 10⁰ S/m observed in the mid-lower crust of Tibet Plateau can be explained by the aqueous fluid with a volume fraction of 1 and 9%, respectively, if the fluid salinity is 25%. The anomaly value of 10^?1 S/m can be explained by the aqueous fluid with a volume fraction of 6% if the salinity is 10%. In case of Southern Tibet where the heat flow is high, the model of a thin layer of brine-bearing aqueous fluid with a high salinity overlying a thick layer of partial melt is most likely to prevail.