首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 140 毫秒
1.
刘加才  张战胜 《江苏地质》2014,38(4):687-692
金龙村边坡位于四川省梓潼县境内,汶川县东,距离汶川地震中心约150 km。通过现场调查,分析了地形、地貌条件和地震等因素对该边坡稳定性的影响。发现滑动面位于土层与基岩的接触面,采用极限平衡法和数值分析法对边坡的稳定性进行了计算,2种计算得到的稳定性结果较为接近。采用动力时程分析法计算得到了边坡位移与加速度变化的关系。  相似文献   

2.
三峡库区康家嘴滑坡破坏过程及演绎研究   总被引:1,自引:0,他引:1  
三峡库区康家嘴滑坡是在其老滑坡泥石流的前缘堆积扇体中形成的新滑动变形体。滑体表面为第四纪风化土层,滑带为灰绿色粉质粘土或粘土,在降雨与库区蓄水的周期性浸泡作用下,饱和后蠕滑变形,处于欠稳定-极限稳定状态,亟需整治。本文针对其破坏过程及形态加以详细描述,并对滑坡的阶段性演绎过程加以追溯。在查清滑坡地质条件与发展趋势的基础上,通过经济对比分析,对康家嘴滑坡不同变形阶段提出了具有针对性的防治方案:在新滑坡体(强变形区)采用抗滑桩+排水沟+局部回填压脚、后部变形体采用抗滑桩+排水沟。经对滑体计算,该滑坡体处于稳定状态,达到了防灾减灾的目的。  相似文献   

3.
物质点强度折减法及其在边坡中的应用   总被引:1,自引:0,他引:1  
王双  李小春  石露  刘召胜 《岩土力学》2016,37(9):2672-2678
物质点法适用于模拟连续介质大变形,如边坡失稳全过程。在物质点法中应用强度折减法,用于边坡稳定性评价。与极限平衡法相比,二者安全系数计算值、滑动面位置结果基本一致;与有限元强度折减法相比,物质点法失稳评价标准的物理意义明确。利用物质点法大变形计算优势,评价边坡失稳后的破坏后果,通过算例说明其评价不同安全系数下的滑坡堆积形态及滑移距离的能力,尤其是评价滑坡对临近建筑物的影响程度的能力。物质点强度折减法可用于边坡稳定性评价及边坡破坏后果评价。  相似文献   

4.
To investigate the formation mechanism and the stability of Wanjia middle school slope in Wenchuan Earthquake Area, the macroscopic geological characteristics and the failure process of the landslide are researched by engineering geology analysis method, limit equilibrium method, and finit element method. The results show that after the Wenchuan Earthquake, retaining walls, houses and other infrastructure on the foot of Wanjia middle school slope were severely destroyed, 10 cm wide tension fracture appeared at the trailing edge of the slope. Wanjia middle school slope is a type of medium-sized soil landslide. The area of the deformation body is about 19,314 m2, the total volume of the deformation body is about 23 × 104 m3. There may be two potential sliding surfaces in the unstable slope: shallow and deep landslide. The analysis results of the limit equilibrium method and the finite element method show that: under dead weight, dead weight + rainstorm, dead weight + earthquake conditions, the plastic zone occurs mainly at the middle part or the trailing edge of the slope, and it doesn’t fully cut through the deep landslide body, so the deep landslide is stable. However, under rainstorm or earthquake conditions, the plastic zone almost completely cut thorough the shallow landslide body, it shows that the shallow landslide is in the understable–basic stable state. It is found that the results of finite element method is concordant with the results of the limit equilibrium method (F s = 1.06–1.29, the shallow landslide is in the basic stable–stable state). The calculation results show that shallow landslides are likely to occur in Wanjia middle school slope during a rainstorm or an earthquake, so monitoring and control of the slope should be strengthened. The shallow landslide should be managed by some measures, such as anti slide pile retaining structures and drainage works, and the dangerous rock bodies on the slope surface should be cleaned up.  相似文献   

5.
土门子滑坡位于重庆市江津区,自1992年以来滑坡体蠕动变形持续发展,近期变形进一步加剧造成滑体内公路及房屋破坏。在研究滑坡地质环境和变形特征的基础上,对滑坡的成因机制进行了进一步深入研究,并对滑坡体的稳定性进行分析评价。结论表明,滑坡体处于整体蠕动变形局部滑移,持续强降雨是诱发其失稳破坏的主导因素在暴雨工况下,滑坡体处于欠稳定~基本稳定极限状态,可能沿多个剪出口发生失稳破坏。  相似文献   

6.
长江三峡库区位于我国地形第二、三级阶梯过渡地带,地质环境复杂,斜倾顺层基岩滑坡较为发育。本文以重庆石柱龙井滑坡为例,详细分析了大型斜倾顺层基岩滑坡的变形特征、成因机理和破坏模式、并采用极限平衡法计算了滑坡在四种工况条件下的稳定性。结果表明:(1)龙井滑坡位于扬子准地台石柱向斜北西翼,体积约1.42×106 m3,主滑方向162°,前缘发育两个次级滑坡;(2)受地形地貌、地层构造、地下水和降雨等因素影响,滑坡目前处于蠕滑变形阶段,变形方式主要为拉张裂缝、剪切裂缝和局部鼓胀变形;(3)滑坡同时处于暴雨和前缘次级滑坡滑动条件下,稳定性为1.03,处于欠稳定状态,滑坡易沿软弱夹层发生整体滑动破坏。  相似文献   

7.
穆文平  王康  钱程  邢渊  王卓然  朱阁  武雄 《岩土力学》2016,37(3):802-812
青海上湾特大型老滑坡体是一个典型的多期次第四系上更新统黄土与新近系贵德群泥岩切层旋转滑坡,滑动面主要位于新近系贵德群泥岩内。在充分利用现场滑坡勘查和钻探试验所获取资料的基础上,通过对滑坡堆积物中的关键层(黄土状土和砾岩堆积物)与泥岩堆积物的空间位置组合关系的研究,以及对老滑坡体底滑面的形态和黄土状土顶部的淤泥(堰塞湖湖积物)的分析,确定了上湾特大型老滑坡体主要经历了两次规模较大的滑动。利用地下水动力学的理论,计算出两次滑动前的地下水位,并建立了分析滑坡变形与破坏机制的数值模型。综合区域新构造运动特点、地下水位的动态变化、新近系贵德群泥岩在饱水状态下力学强度显著下降的特征以及FLAC3D数值模拟结果,得出老滑坡体第1次滑动主要是由于河流下切作用引起,并给出了河流下切过程中坡体变形的3个阶段。第2次滑动是由于第1次滑动后,斜坡临空面变陡,坡脚剪应力进一步集中,且在其前缘形成一个堰塞湖,导致地下水位上升软化泥岩而发生的累进性牵引滑动。  相似文献   

8.
以青海省南部省道红土山段滑坡为例,在分析区域地质概况和滑坡特征的基础上,对滑坡机理及影响滑坡的因素进行分析,确定滑坡滑动模式;选取合理的计算参数进行滑坡稳定性计算,根据计算结果对滑坡稳定性进行分析。得到以下结论:产生滑坡体病害的主要原因是滑坡所处区域冻土深度较大,区域冬夏温差大,地表水下渗后冻胀,次年夏初消融,这使粘性土及泥岩泥化,粘聚力降低,周而复始,滑体不断蠕动下滑。采用传递系数法对滑坡在不同工况下的稳定性进行计算,结果表明,在天然状态下滑坡浅层滑面处于蠕动变形状态,深层滑面基本稳定;在考虑暴雨和地震的条件下,滑坡处于不稳定状态。  相似文献   

9.

当前滑坡滑面运动特征获取多采用接触式手段,费时费力、成本高昂,且仅能获取稀疏点位滑面运动状态。因此,本文提出一种非接触式滑坡滑面运动特征获取方法,其基本思路是:基于位错理论建立滑坡表面形变与滑面运动间的关系模型,同时引入滑面运动平滑约束条件,最终以InSAR等技术获取的地表形变为约束,反演获得滑面运动特征。本文选择四川省汶川县布瓦村滑坡作为研究对象,以时序InSAR技术获取的滑坡坡面升降轨形变数据为约束,基于发展的理论方法反演获得布瓦村滑坡滑面几何与运动学参数,并结合野外勘查、Lidar观测以及模型残差较好地验证了反演结果的可靠性,其中反演升降轨模型残差仅3.1 mm ·a-1和3.4 mm ·a-1。反演结果显示,布瓦村滑坡滑面位于坡表以下平均~15.0 m深度处,滑面整体以沿坡向运动为主,最大运动量级达~80 mm ·a-1,同时在坡体西侧中下部发现微量的垂直坡向运动。本文提出方法可方便、快速的获取空间连续的滑坡滑面运动特征,为滑坡灾害预警和失稳风险评估提供更为直接可靠的科学参考。

  相似文献   

10.
2015年7月11日23时,受前期连续降雨和灿鸿台风短时强降雨影响,浙江省绍兴市太平山村滑坡在2000年首次发生滑动变形基础上,再次出现剧烈的变形迹象,前缘土体明显隆起,滑坡边界急剧扩大,直接威胁到下方约25幢居民住户的生命财产安全。本文在地表裂缝、滑坡表面位移及坡体深层水平位移监测基础上,结合详细的地质调查、现场工程地质测绘、含水率及渗透试验等手段,对太平山村滑坡的基本特征进行了分析,并形成了滑坡形成机制及破坏模式的初步认识。结果表明:(1)滑坡平面形态呈圈椅状,主滑方向约140,滑坡体斜长约330m,前缘宽150~180m,后缘宽度约75~105m,厚15~25m,体积105104m3,以残坡积和坡洪积含碎石粉质黏土层为主;(2)强降雨是诱发滑坡体失稳变形的主要因素;(3)滑坡基本呈蠕动变形状态,滑动速度缓慢,仅在强降雨条件下出现依次明显的错动,一般时期内基本保持稳定状态,可以判定为牵引式滑坡。  相似文献   

11.
Stability analysis of a large landslide in hydropower engineering   总被引:1,自引:1,他引:0  
This paper is devoted to stability analysis of the Zheng-Gang landslide in the Gu-Shui hydropower station in China. Based on the geological field investigations, the formation processes, the deformation mechanism related to rainfalls and the instability mode are first analyzed. Large scale direct shear tests on soils in the slip zone are performed in order to characterize influences of the content of particle and water on natural shear strength. Due to the difficulty to consider the lateral constrain and curvature effects of the bottom sliding surface, different three-dimensional models are established using the limit equilibrium method and the large strain Lagrange finite difference method. The results of stability analysis are in good agreement with the field observations. It is shown that the natural landslide is in a limit state and the creep deformation along the slipping surface is the main mechanism of landslide instability under in situ conditions.  相似文献   

12.
在分析矿区地形地貌、地层岩性、水文地质条件和影响排土场稳定因素的基础上,结合区内2#排场的监测资料,采用FLAC3D模拟软件和刚体极限平衡法中的毕肖普条分法,对排土场边坡变形、破坏的主要影响因素进行了分析,揭示了其滑坡机理;对3#排土场的稳定性做出预测,认为排土场边坡变形破坏模式是上部排弃物沿圆弧滑面剪切滑移与下部沿粉土、粉质粘土平面滑移的圆弧—平面组合滑移形式;基底土层的内摩擦角对排土场允许排高较为敏感,是决定允许排高的内在因素,基底粉质粘土的极限承载力是决定排土场允许排高的外在因素;基底土体极限承载力所决定的排土场的允许排高为90.60~91.60m。提出了填沟压脚、降低第一排台阶高度和基底排水等措施来满足排土场边坡稳定的要求。  相似文献   

13.
孟家山黄土-红层接触面滑坡破坏机理研究   总被引:5,自引:1,他引:4  
本文以天水市孟家山滑坡为例,分析了黄土-红层接触面滑坡的发育特征,运用相似材料物理模拟试验,研究了“坡体蠕动—后缘拉裂—滑带由中部向两侧发展—剪出口形成—坡体突滑”的变形破坏机理。  相似文献   

14.
旋转平推式滑坡在青藏高原东北缘地区集中分布,论文系统梳理了该类滑坡的分布特征、几何应变模型,结合室外调查、试验与数值模拟计算,探讨了近水平滑动带变形的动力机制。研究表明:(1)旋转平推滑坡集中分布于东北缘上新世泥岩盆地内,其活动强度受到青藏高原隆升过程的影响,自高原腹地至边缘盆地,滑体体积逐步减小。巨大型滑坡群集中于黄河水系上游地区;大、中型型滑坡群分别集中于下游地区;(2)旋转平推滑坡均由高黏粒含量、超固结上新世泥岩组成,河流的侵蚀是近水平剪切应力形成的控制性因素。在水平应力作用下,超固结泥岩趋向与膨胀,表现出剪胀、渐进性破坏。薄层剪切带呈现韧、脆性变形,区域内随机排列的黏土颗粒的逐步定向,表现出低于10o的内摩擦角。(3)滑动带的蠕变、裂隙扩展与地下水的增湿加速材料的流变,滑面选择粘粒含量高、碳酸钙的含量低的软弱层扩展。滑带内粘土矿物蠕变、呈粘滞性流动,导致宏观变形逐步积累,并逐步出现剪切面、裂纹的扩展,是滑坡变形的动力因素之一。  相似文献   

15.
本文以高治村滑坡为例,论述了FLAC3D在滑坡稳定性分析评价中的应用。作者首先介绍了FLAC3D的基本原理和主要流程,然后采用摩尔-库伦模型,对高治村滑坡在天然状态和暴雨状态下的变形和位移情况进行了数值模拟,模拟结果直观地显示了该坡体在上述两种状态下的塑性变形及水平方向位移的分布特征,清楚地显示了坡体内潜在的滑动面。文章根据数值模拟结果,对该滑坡的稳定性进行了分析和评价,对该滑坡的变形和破坏形式进行了研究和探讨。通过对该坡体的塑性变形与位移情况分析认为,该滑坡在天然状态下基本稳定;在连续高强度降雨状态下欠稳定,局部失稳滑塌的可能性很大,这与现场调查分析的结果一致。这个结果表明,利用FLAC3D进行滑坡稳定性分析和评价简单、可行,且更加直观、方便,具有传统极限平衡法所无法比拟的优势。  相似文献   

16.
齐明柱 《工程地质学报》2010,18(S1):346-352
径肚滑坡群由HP1和HP2两条滑坡组成,发育在低山前缘丘陵地带,滑坡场地揭示的地层主要为流纹质凝灰岩及其风化物。HP1滑坡属于既有滑坡的再次滑动,HP2滑坡系受HP1滑坡牵动形成。滑体主要由块碎石土、粉质黏土夹块碎石组成; 主滑段滑带主要由棕黄色、棕红色黏性土组成; 滑床为全风化流纹质凝灰岩。通过深入分析滑坡变形特征和工程地质条件,论证了径肚滑坡群的成因、性质,分析了大气降雨在滑坡生成过程中的作用。指出开挖坡脚使坡体失去支撑是滑坡复活的直接原因,长时间持续的强降雨是发生滑坡的诱发因素。在深圳等降雨量大的亚热带气候区,大气降雨和深层滑动之间没有必然联系,但久雨能够降低深层滑坡的动态稳定性,并促使滑坡发生。深圳地区广泛分布的凝灰岩风化物,在一定的含水条件下成为易滑地层。  相似文献   

17.
To monitor land deformation in detail, we ran a large-scale field test in which an artificial landslide was induced by the application of a load to a natural slope. The measured landslide displacement was reproduced numerically through the use of finite element model analysis with a two-dimensional elasto-viscoplastic model. The analysis suggested that the strength of the sliding surface decreased as the landslide mass moved. We propose a simple method for estimating safety factors. The method involves back-calculation of shear strength parameters through reproduction of observed landslide displacements and calculating the ratio of driving force to resisting force acting on the sliding surface as modeled by joint elements. This ratio, the “stability index”, shows the same trend as safety factors calculated by a two-dimensional limit equilibrium method and a shear strength reduction method that use back-calculated shear strength parameters estimated from the limit equilibrium state. The results indicate that the stability index may be applicable to the assessment of slope stability.  相似文献   

18.
The Guantan landslide, with a total displaced mass of about 468 × 104 m3, was triggered by the 2008 Wenchuan earthquake and succeeding rainfall in Jushui Town, Sichuan Province, China. The landslide occurred on an anti-dip hard rock slope with a weak rock founding stratum of 200 m in thickness. To investigate the failure mechanism of the Guantan landslide, dynamic behaviors of hard and soft rock slopes were investigated by means of large scale shaking table tests. The laboratory models attempted to simulate the field geological conditions of the Guantan landslide. Sinusoidal waves and actual seismic waves measured from the Wenchuan Earthquake were applied on the slope models under 37 loading configurations. The experimental results indicated that deformation mainly developed at a shallow depth in the upper part of the hard rock slope and in the upper (near the crest) and lower (near the toe) parts of the soft rock slope. An equation for predicting the depth of sliding plane was proposed based on the location of the maximum horizontal acceleration. Finally, it was concluded that the failure process of the Guantan landslide occurred in three stages: (1) toppling failure caused by compression of the underlying soft rock strata, (2) formation of crushed hard rock and sliding surface in soft rock as the result of seismic shocks, particularly in the horizontal direction, and (3) aftershock rainfall accelerates the process of mass movement along the sliding plane.  相似文献   

19.
阳鹿(阳朔—鹿寨)高速公路K52新滑坡为古滑坡堆积体中局部复活的滑坡,处于急剧变形状态,需进行抢险性处治。复工后对该滑坡进行了详细的地质勘察及变形监测,借助FLAC3D软件对其成因、变形过程及变形机理进行了研究,得到了以下结论:(1)古滑坡堆积体形成于顺层岩质滑坡,堆积体内部发育软-可塑状软弱夹层风化页岩,为新滑坡的主要滑带土;(2)导致新滑坡变形的主要内因为不良地质、微地貌、特殊的岩土结构,主要外因为在中后部堆载、填土改变地表水径流路径、向滑坡排放生活用水及降雨;(3)新滑坡具有三层滑面,失稳前底部滑面为主滑面,失稳阶段中部滑面为主滑面,属前段推移后段牵引型复合式滑坡,具多级、逐级及渐进滑动特点;(4)新滑坡变形进程为:后缘拉张变形-中部剪切蠕变-滑体A、B推移剪出失稳-滑体C前缘临空牵引失稳;(5)新滑坡处治重点应防止顶部、中部及底部三个滑动面继续变形,也应防止古滑面及古滑坡堆积体内部其余风化页岩夹层产生次级滑动。  相似文献   

20.
某边坡变形破坏机理的数值分析   总被引:3,自引:0,他引:3  
某花岗岩矿岩土体主要有填土、粉质粘土、淤泥及淤泥质土、含泥中粗砂、粘土、残积砂质粘土,其下为花岗岩基岩。边坡最大高度75m,其中残积土层以上的土质边坡高度约50m。本文运用有限元强度折减法对该边坡的稳定性进行了研究,得出了潜在的破坏模式及各个滑动部分的安全系数。分析结果表明,本边坡存在3个潜在滑动面,其中两个为浅层滑动面,另一个为深层滑动面。两个浅层滑动面的稳定系数在1.13~1.17,处于临界状态。深层滑动面稳定性系数在1.29,目前尚处在相对稳定状态。根据分析结果,提出了如下加固措施:(1)对滑坡体进行削坡处理;(2)在其滑动面下方设置抗滑台阶;(3)采用预应力锚索框架梁结合肋柱进行加固处理。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号