铅在高岭石表面的吸附模式

采用表面络合模式,研究了高岭石表面的酸碱性质以及高岭石表面对铅的吸附行为。结果表明,高岭石表面在不同ｐＨ条件下对质子和铅离子的吸附反应可以用单一表面基团、无静电表面络合模式来描述。高岭石表面酸度常数拟合值分别为ｐＫａ１＝２．７５和ｐＫａ２＝５．５２,电荷零点ｐＨｚｐｃ＝４．１铅在高岭石表面的吸附量随ｐＨ值的升高而增加,吸附铅的两种表面化合态〉ＳＯＰｂ＾＋和〉ＳＯＰｂＯＨ的浓度也随ｐＨ值的变化而变化     

Study on the adsorption kinetics of orthophosphate anions on layer double hydroxide

A kinetic study was conducted on the adsorption of orthophosphate anions on layer double hydroxide (LDH). The adsorption has proved itself to be a spontaneous endothermic process and is large in capacity and rate. The adsorption isotherm correlates well with the Freundlich model, and a rise in temperature will lead to an increase in adsorption efficiency. Additionally, the results suggested that the adsorption is an entropy-increasing process and is in good agreement with the pseudo-second order kinetics. The free energy (ΔG) of adsorption of orthophosphate onto LDH varies within the range of −1.75–−3.34 kJ/mol, the enthalpy (ΔH) varies by 7.96 kJ/mol and the entropy (ΔS) by 33.59 kJ/mol. The adsorption activation energy is 8.3 kJ/mol, showing that the adsorption of orthophosphate onto LDH is determined to be a physical adsorption.     

胡敏酸对高岭石吸附铜离子的强化作用

考察酸性条件特别是在近中性 pH范围内胡敏酸对高岭石吸附铜离子的强化作用。研究表明 ,胡敏酸的加入可以提高高岭石对铜离子的吸附率 ,甚至在pH 5～ 6附近高岭石对铜离子的吸附率也从约 5 0 %提高到约 6 5 %。当 pH <4时 ,由于高岭石表面铝的高溶出或胡敏酸阴离子基团离解程度降低等因素 ,使其表面对胡敏酸的吸附率有所降低 ,但与高岭石样品相比 ,胡敏酸高岭石复合体对铜离子的吸附仍然有明显的增加。胡敏酸对高岭石吸附铜离子的强化机制是 ,高岭石端面形成了Al—HA—Cu三元配合物 (B型 ) ,与传统的诸如pH、离子强度与离子初始浓度等介质条件影响不同。在 pH >7时高岭石端面及腐殖质基团去质子化增强 ,因而静电排斥降低了高岭石对胡敏酸的吸附 ,从而使得胡敏酸对铜离子在高岭石表面上的吸附作用有所减弱 ,此时可能出现胡敏酸铜及氢氧化铜的沉淀 ,铜离子的表观吸附率可能不会有明显变化     

Experimental study on the competitive adsorption of metal ions onto minerals

The study on the competitive adsorption shows that the magnitude order of metal ions adsorbed onto oxide and silicate minerals in near-neutral solution with low ionic strength is in mole/nm² as follows: CaCO₃ > quarte > hydromuscovite > kaolinite > Ca-montmorillonite > goethite > gibbsite. These minerals can be divided into three groups according to their surface equilibrium constantsK _M of the adsorption reactions, which are the function of the dielectric constants ε of the absorbent minerals. The relationships between constantsK _M and mineral dielectric constants ε are described as follows: lgK _M ¹ = 7.813-26.15/ε lgK _M ² = 9.030-26.15/ε lgK _M ³ =11.63-26.15/ε for the adsorption reaction: >SO^- + Mⁿ⁺≥SOM^n-1)+ (n = 1, 2, 3) The first group of minerals include quartz, goethite, 1:1 phyllosilicates and other oxide minerals; the second: gibbsite, brucite and 2:1 phyllosilicates; the third: carbonate, sulphate and phosphorate minerals. The appearance reaction constants have a variation of magnitude ±0.5 for different metal ions with the same mineral. This project was financially supported by the National Natural Science Foundation of China (No. 49572091).     

高岭石和蒙脱石吸附胡敏酸的对比研究

高岭石和蒙脱石分别是暖湿和冷干气候带内典型土壤的代表性矿物,对二者吸附胡敏酸特点的对比研究可以为探索不同地带土壤中重金属的环境行为提供重要的依据。笔者通过一系列实验研究了pH值、离子强度和胡敏酸初始浓度对胡敏酸在高岭石和蒙脱石上吸附量的影响,重点剖析了引起高岭石和蒙脱石在吸附胡敏酸方面表现出的共性和差异的原因。研究结果表明:1)在pH=5条件下,胡敏酸在高岭石和蒙脱石上的吸附量均随着胡敏酸初始浓度和离子强度的升高而逐渐增加;2)胡敏酸在高岭石和蒙脱石上的吸附量均随着pH值的升高而降低;3)pH<6时,高岭石吸附的胡敏酸量多于蒙脱石,pH>6时则相反。这是由高岭石和蒙脱石在不同pH条件下吸附胡敏酸的机制不同造成的。在pH<6时,高岭石与胡敏酸之间的静电引力起主导作用,其次是配位交换作用和氢键作用。此时,蒙脱石以氢键作用为主要吸附机制。在pH>6时,高岭石和蒙脱石的主要吸附机制分别是疏水性作用和阳离子键桥。     

Surface complexation model for multisite adsorption of copper(II) onto kaolinite

We measured the adsorption of Cu(II) onto kaolinite from pH 3-7 at constant ionic strength. EXAFS spectra show that Cu(II) adsorbs as (CuO₄H_n)ⁿ⁻⁶ and binuclear (Cu₂O₆H_n)ⁿ⁻⁸ inner-sphere complexes on variable-charge ≡AlOH sites and as Cu²⁺ on ion exchangeable ≡X--H⁺ sites. Sorption isotherms and EXAFS spectra show that surface precipitates have not formed at least up to pH 6.5. Inner-sphere complexes are bound to the kaolinite surface by corner-sharing with two or three edge-sharing Al(O,OH)₆ polyhedra. Our interpretation of the EXAFS data are supported by ab initio (density functional theory) geometries of analog clusters simulating Cu complexes on the {110} and {010} crystal edges and at the ditrigonal cavity sites on the {001}. Having identified the bidentate (≡AlOH)₂Cu(OH)₂⁰, tridentate (≡Al₃O(OH)₂)Cu₂(OH)₃⁰ and ≡X--Cu²⁺ surface complexes, the experimental copper(II) adsorption data can be fit to the reactions

     

Preferential polymerization and adsorption of L-optical isomers of amino acids relative to D-optical isomers on kaolinite templates

Experiments on the polymerization of the L- and D-optical isomers of aspartic acid and serine using kaolinite as a catalyst showed that the L-optical isomers were polymerized at a much higher rate than the D-optical isomers; racemic (DL-) mixtures were polymerized at an intermediate rate. The peptides formed from the L-monomers were preferentially adsorbed by the clay. In the absence of kaolinite, no significant or consistent difference in the behavior of the L- and D-optical isomers was observed. In experiments on the adsorption of L- and D-phenylalanine by kaolinite, the L-optical isomer was preferentially adsorbed. Adsorption of L-phenylalanine was sensitive to pH, whereas adsorption of D-phenylalanine was not. The experimental results indicate that catalytically active faces of the kaolinite crystals acted as specific templates which preferentially adsorbed and polymerized molecules with the L-configuration. The observed discrimination between the L- and D-optical isomers of the amino acids evidently occurred on the enantiomorphous edge (hk) faces of the kaolinite. These findings may have significance for the pre-biotic origin of proteins.     

Surface complexation modeling of Cu(II) adsorption on mixtures of hydrous ferric oxide and kaolinite

Background  

The application of surface complexation models (SCMs) to natural sediments and soils is hindered by a lack of consistent models and data for large suites of metals and minerals of interest. Furthermore, the surface complexation approach has mostly been developed and tested for single solid systems. Few studies have extended the SCM approach to systems containing multiple solids.     

高岭石和埃洛石-7Å对稀土元素吸附特征的实验研究

针对赣南风化淋积型稀土矿中稀土元素的分异现象,通过研究该稀土矿的主要矿物成分——高岭石和埃洛石-7的矿物特征及其在不同条件下的吸附特征,探讨了该类型稀土矿的成矿机制和稀土元素分异机理。高岭石和埃洛石-7吸附稀土元素的能力受体系p H值以及金属阳离子钾、钠的的影响,且埃洛石-7吸附稀土元素的能力高于高岭石。横向对比实验结果表明当体系中赋存有K+时,两种粘土矿物对稀土元素的吸附呈现出分化趋势,其中高岭石主要吸附中-重稀土元素,埃洛石-7反之,因此风化淋积型稀土矿风化过程中释放出的K+可能会使高岭石和埃洛石-7呈现出差异吸附特征,进而反过来影响稀土矿中稀土元素的配分。     

Kinetic mechanism of competitive adsorption of disperse dye and anionic dye on fly ash

The adsorption behavior of four anionic dyes and one disperse dye in single solution and binary solutions on fly ash was investigated in order to elucidate the effect of competitive adsorption on the kinetics. The experimental findings showed that adsorption equilibriums of four anionic dyes were reached within 50 min either in the single solution or in binary mixtures. Competitive adsorption increased the time of attaining equilibrium of disperse dye. Desorption of dyes suggested the predominant adsorption mechanisms, that is, chemisorption for anionic dyes and physisorption for disperse dye. For the binary mixtures, the anionic dyes could be adsorbed preferentially on fly ash at the first stage. Second-order kinetic models fitted better to the equilibrium data of all dyes in the single solution as well as in the binary mixtures. The maximum rate constant of intraparticle diffusion and the minimum external mass transfer coefficient was found for disperse dye both in single and in binary solutions. The intraparticle diffusion constants and external mass transfer coefficients of the four anionic dyes in binary solution are similar to those obtained in single solution. The Biot number confirmed that the intraparticle diffusion was the rate-limiting step in the dye sorption process.     

煤系高岭石的原始晶粒尺寸及结晶度对插层作用的影响

采用SEM、XRF、XRD和IR研究了大同、平朔和淮北煤系高岭石的结构、粒度及其特性,探讨了粒度大小对高岭石插层作用的影响及其机理。研究发现:粒度中等且结晶有序的平朔煤系高岭石插层率最高,其次为晶体粗大但结晶有序的大同高岭石,粒度最小且结晶无序的淮北高岭石插层率最低。研究认为高岭石原始晶粒粒度对高岭石插层作用有重要影响,中等粒度最有利于高岭石插层作用的进行,粒度过大或过小均不利于高岭石插层作用的进行,其原因是由于不同粒度的高岭石插层作用过程中导致的差异弹性变形引起的。结晶有序度对高岭石插层作用也有重要影响,结构无序不利于插层作用的进行。     

Surface complexation modeling of Co(II) adsorption on mixtures of hydrous ferric oxide, quartz and kaolinite

Co sorption was measured as a function of pH, ionic strength (0.001-0.1 M NaNO₃) and sorbate/sorbent ratio on pure quartz, HFO and kaolinite and on binary and ternary mixtures of the three solids. Sorption data measured for the pure solids were used to derive internally-consistent diffuse layer surface complexation model (DLM) stability constants for Co sorption. Co sorption on HFO could be adequately modeled over a broad range of ionic strengths and sorbate/sorbent ratios with a two variable-charge site model. Fits based on a single variable-charge site model were reasonable, but were improved by using ionic-strength dependent stability constants. A single variable-charge site model with an additional permanent ion exchange site produced the best fit to Co edges measured on kaolinite over a range of ionic strength and sorbate/sorbent ratios. These DLM fits were also improved by using ionic-strength dependent stability constants. The DLM approach could not adequately describe the slope of Co sorption edges on quartz. This study demonstrates that for accurate prediction of Co sorption over wide ranges of ionic strength and sorbate/sorbent ratio, the DLM may require ionic-strength dependent stability constants. DLM stability constants for Co sorption derived for the pure solids were used to predict sorption as a function of pH and solid concentration on binary and ternary mixtures of the three solids. Discrepancies between predictions and measurements were quantitatively similar to those observed for the pure mineral systems. Thus, a simple component additivity approach provides useful predictions of metal sorption in the mixed solid systems.     

Feldspar dissolution in the presence of organic acid anions under diagenetic conditions: an experimental study

Previous experiments to determine the aqueous solubility of lead-rich orthoclase in the presence of the ethanoic acid anion (acetate) at 150°C and 50 MPa have shown that the observed fluid compositions are essentially controlled by the presence of secondary mineral precipitates, which buffer dissolved species apart from lead. Data for lead suggest that dissolution increased with increasing fluid ethanoic acid anion content, but the ethanoic acid anion was unstable under the experimental conditions. Additional experiment have now been carried out using pure natural albite and ethanoic acid anion solutions at 150°C and 50 MPa, in which the ethanoic acid anion remains stable. The results for albite again demonstrate the influence on fluid composition of secondary mineral precipitates, but data for silica allow the rates of dissolution to be estimated. Values obtained for the dissolution rate constant increase from 1.8 × 10⁻⁷ to 5.3 × 10⁻⁷ s⁻¹ with increasing fluid ethanoic acid anion content (0.1–2.5 molal) and approximate to values for quartz and orthoclase dissolution rates for similar PT conditions, reflecting similarity in the mechanisms of dissolution of the minerals' three dimensional (alumino)silicate frameworks. However, these experiments provide no other evidence that the ethanoic acid anion enhances equilibrium solubilities of feldspars or quartz. In contrast to the results for the ethanoic acid anion, data for albite dissolution experiments in the presence of the ethanedioic acid anion (oxalate) at 150°C and 50 MPa show an inhibitionn of solubility (apart from aluminium), while data for the 2-hydroxy-1,2,3-propanetricarboxylic acid trivalent anion (citrate) show considerable enhancement of solubility for aluminium and silicon, and titanium derived from the reaction vessel. The 2-hydroxy-1,2,3-propanetricarboxylic acid trivalent anion is unstable, decaying according to first order kinetics (half life = 1.5 days). In their application to problems of diagenesis in the presence of organic acid anions, these results suggest that the ethanoic acid anion may influence feldspar dissolution by accelerating diagenetic reactions, while geologically short-lived species such as the 2-hydroxy-1,2,3-propanetricarboxylic acid trivalent anion and its decay products may dramatically enhance aluminosilicate solubility.     

Numerical modelling of competitive components transport with non‐linear adsorption

A characteristic finite element (CFE) algorithm for modelling contaminant transport problems coupled with non‐linear competitive adsorption is presented. An alternative algorithm, termed as the transport‐equilibrium Petrov–Galerkin (TEPG) methods in this paper, is also presented for comparison. Through analyses of a number of examples with Peclet number ranging from zero to infinity, it is shown that the CFE algorithm is very competitive with the middle–point TEPG method in terms of accuracy, stability and efficiency. The fully explicit and fully implicit TEPG methods are found to be less appropriate for transport problems coupled with non‐linear equilibrium equations. Copyright © 2000 John Wiley & Sons, Ltd.     

Siderophore adsorption to and dissolution of kaolinite at pH 3 to 7 and 22°C

Siderophores are Fe(III)-specific ligands produced by many aerobic microorganisms under conditions of iron stress. This study examined adsorption of the commercial trihydroxamate siderophore, desferrioxamine B (DFO-B), to an iron-containing kaolinite (0.1 bulk wt.% Fe) and examined DFO-B effects on initial kaolinite dissolution and iron release rates. Adsorption experiments were conducted at pH 3 to 8 in 0.01-M NaClO₄ in the dark and at 22°C; batch initial dissolution experiments were conducted to 96 h.The adsorption envelope (i.e., adsorption as a function of pH) of DFO-B on kaolinite was consistent with cation-like behavior, with adsorption increasing above kaolinite’s pH_pznpc of 4.9. DFO-B enhanced aluminum release from kaolinite at pH 3 to 7, relative to HNO₃, which is consistent with the ligand’s high binding affinity for Al. Correlation between DFO-B adsorption and aluminum release suggested a surface-controlled, ligand-promoted dissolution mechanism. DFO-B had no effect relative to HNO₃ on silicon release at pH 3 and 5, but moderately enhanced silicon release at pH 7. DFO-B enhanced iron release from kaolinite, with dissolved iron concentrations in the 10-ppb range at 96-h reaction time. These results show that kaolinite may serve as a source of iron to aerobic microorganisms in iron-limited conditions and that siderophores may affect kaolinite dissolution and iron content.     

德安锑矿区土壤中锑的形态分析及生物可给性初探

按Tessier连续浸提法对德安锑矿区土壤样品进行了分析,得出锑的存在状态主要以残渣态为主,其次是Fe/Mn结合态,有机/硫化物结合态和碳酸盐结合态,可交换态和水溶态占的比率最小。矿区土壤中锑生物可利用态锑占0.52%~3.51%,其浓度一般在1.78~17.48μg/g,中等可利用态占1.04%~5.56%,生物难利用态锑的浓度占92.1%~98.4%。     

锑矿区水体水环境锑污染及硫同位素示踪研究

本文系统研究了贵州省半坡锑矿区水环境锑污染现状,用硫同位素指示采矿活动对矿区水体的影响,以查明锑矿区水环境中Sb的释放迁移过程和水污染程度。研究发现,矿区水体中Sb和SO42-含量分别高达1377μg/L和1926 mg/L;岔河下游近10 km处仍保持较高水平(182.5μg/L Sb和59.8 mg/L SO42-)。岔河水体中,δ34S-Sb、δ34S-SO42-和Sb-SO42-间均具显著正相关,相关系数分别为r=0.68(p<0.05)、r=0.89(p<0.01)、r=0.72(p<0.05)。表明岔河水体中,δ34S和SO42-能很好地指示矿业活动引起的Sb污染程度和扩散范围。根据同位素质量平衡原理估算,发现矿区下游水体中的硫主要来自矿山,表明矿区下游水体污染受采矿活动影响显著。     

The mechanism of fatty acid adsorption in the presence of fluorite,calcite and barite

The interaction of oleic acid with fluorite, calcite and barite has been studied using solubility, oleate abstraction, electrophoretic mobility and Hallimond-tube flotation measurements. Abstraction of oleate from aqueous solution corresponds to the precipitation of the metal oleate. Multilayers of metal oleate inhibits the dissolution of the minerals and prevents true equilibrium from being obtained. Flotation is not only dependent on the amount of oleate abstracted but also on the strength of adhesion of the precipitated metal oleate to the minerals. Selectivity between the flotation of calcite, fluorite and barite is unlikely to be obtained by varying the pH because similar responses are observed.     

Sorption of lanthanides on smectite and kaolinite

Experiments were carried out to investigate the sorption of the complete lanthanide series (Ln or rare earth elements, REE) on a kaolinite and an a Na-montmorillonite at 22°C over a wide range of pH (3-9). Experiments were conducted at two ionic strengths, 0.025 and 0.5 M, using two different background electrolytes (NaNO₃ or NaClO₄) under atmospheric conditions or N₂ flow (glove box). The REE sorption does not depend on the background electrolyte or the presence of dissolved CO₂, but is controlled by the nature of the clay minerals, the pH and the ionic strength. At 0.5 M, both clay minerals exhibit the same pH dependence for the Ln sorption edge, with a large increase in the sorption coefficient (K_D) above pH 5.5. At 0.025 M, the measured K_D is influenced by the Cation Exchange Capacity (CEC) of the minerals. Two different behaviours are observed for smectite: between pH 3 and 6, the K_D is weakly pH-dependent, while above pH 6, there is a slight decrease in log K_D. This can be explained by a particular arrangement of the particles. For kaolinite, the sorption coefficient exhibits a linear increase with increasing pH over the studied pH range. A fractionation is observed that due to the selective sorption between the HREEs and the LREEs at high ionic strength, the heavy REE is being more sorbed than the light REE. These results can be interpreted in terms of the surface chemistry of clay minerals, where two types of surface charge are able to coexist: the permanent structural charge and the variable pH-dependent charge. The fractionation due to sorption observed at high ionic strength can be interpreted either because of a competition with sodium or because of the formation of inner-sphere complexes. Both processes could favour the sorption of HREEs according to the lanthanide contraction.     

氢化物发生—原子荧光法直接测定锑及其化合物中的铅

通过在样品处理阶段用HBr除去大量锑基体,实现了不需再通过其他化学分离直接运用氢化物发生-原子荧光法测定锑及其相关产品中的微量铅,并用于实际样品的分析.该方法对样品检测下限小于10-6,在实际样品分析中,分析结果与原子吸收法测定结果之间无显著性差异,RSD＜2.0%(n=4),对样品分析的加标回收率在95%～105%.