An intercomparison of hydrological network-design technologies

Abstract

Two network-design technologies are compared by random sub-sampling of actual streamflow data. The technologies, Network Analysis for Regional Information (NARI) and Network Analysis Using Generalized Least Squares (NAUGLS), have a common objective, viz. to maximize regional information within a limited budget and time horizon. The data used for intercomparison are from a network of 146 streamgauges in the central part of the United States. In general, the results for the illustrative example indicate that the NAUGLS method conveys more information than the NARI method to the network designer interested in maximizing regional information about mean annual flows with a limited budget.     

An intercomparison of remotely sensed soil moisture products at various spatial scales over the Iberian Peninsula

Soil moisture (SM) can be retrieved from active microwave (AM), passive microwave (PM) and thermal infrared (TIR) observations, each having unique spatial and temporal coverages. A limitation of TIR‐based retrievals is a dependence on cloud‐free conditions, whereas microwave retrievals are almost all weather proof. A downside of SM retrievals from PM is the coarse spatial resolution. Although SM retrievals at coarse spatial resolution proved to be valuable for global‐scale and continental‐scale studies, their value for regional‐scale studies remains limited. To increase the use of SM retrievals from PM observations, an existing method to enhance their spatial resolution was applied. We present an intercomparison study over the Iberian Peninsula for three SM products on two different spatial sampling grids. The remotely sensed SM products were also compared with in situ observations from the Remedhus network. Variations between ground data and satellite‐based SM are observed; all three remotely sensed SM products show good agreement to the ground observations. The comparison shows that these ground observations and satellite data are consistent, based on the correlation coefficient (R) and root mean square error (RMSE). The remotely sensed products were intercompared after sampling at 25 × 25 km² and after applying the smoothing filter‐based intensity modulation (SFIM) downscaling technique at 10 × 10 km² grids. After the application of the SFIM technique, the SM retrievals from PM observations show better agreement with the other remotely sensed SM products for approximately 40% of the study area. For another 40% of the study area, we found a similar agreement between these product combinations, whereas in extreme environments, both arid and densely vegetated regions, the agreement decreases after the application of the SFIM technique. Agreement between retrievals of absolute SM content from PM and TIR observations is generally high (R = 0.77 for semi‐arid areas). This study enhances our understanding of the remotely sensed SM products for improvements of SM retrieval and merging strategies. Copyright © 2013 John Wiley & Sons, Ltd.     

ASOND-78: An intercomparison of Väisälä, VIZ and Swiss radiosondes

This paper describes an intercomparison between the Väisälä, VIZ and Swiss (used at upper-air station 06610) radiosondes. The field experiment was supported by a series of carefully implemented laboratory tests. The results show that the temperature sensor data from the SMI and VIZ sondes both require additional radiation compensation for daylight ascents whilst the Swiss sonde's pressure sensor has particularly large errors in the 200–100 mb region. New correction parameters have been determined for the SMI and VIZ sondes and these have now been built into the systems' software.     

An evaluation of the apparent dissociation constants of carbonic acid in seawater

The internal consistency of five sets of apparent dissociation constants of carbonic acid in seawater obtained by Buch (1951), Lyman (1956), Edmond and Gieskes (1970), Hansson (1973) and Mehrbach et al. (1973) have been tested using the GEOSECS Atlantic data for the total alkalinity, the total CO₂ concentration and the partial pressure of CO₂. As a measure of the consistency for each of the five sets of the dissociation constants with the data, the 77 measured values of the partial pressure of CO₂ have been compared with those calculated from the alkalinity and total CO₂ values determined for these samples. It has been found that: (1) the apparent dissociation constants of Lyman (1956), Hansson (1973) and Mehrbach et al. (1973) appear to be internally consistent with the data, whereas those of Buch (1951) and of Edmond and Gieskes (1970) appear to be markedly inconsistent with the GEOSECS data; and (2) on the basis of a statistical analysis of the data grouped in three temperature ranges, the dissociation constants of Lyman (1956) and of Mehrbach et al. (1973) appear to be most satisfactory.     

An intercomparison between finite difference and finite element (TELEMAC) approaches to modelling west coast of Britain tides

A finite element model (namely TELEMAC) with a range of mesh refinements and assumptions of coastal water depths is used to determine an optimal mesh for computing the M ₂ tide in a region of significant geographical extent. The region adopted is the west coast of Britain covering the Irish and Celtic Seas. The nature of the spatially varying topography and tidal distribution, together with a comprehensive set of measurements and existing accurate finite difference model makes it ideal for such a study. Calculations show that a water-depth dependent criterion for determining element size gives an optimal distribution over the majority of the region. However, local refinements in narrow channels such as the North Channel and Bristol Channel are required. Although the specification of a zero coastal water depth, leads to a fine near coastal grid, this does not yield the most accurate solution. In addition the computational cost is high. In practice in a large area model the use of a non-zero coastal water depth yields optimum accuracy at minimal computational cost. However, calculations show that accuracy is critically dependent upon nearshore water depths. Comparison with the finite difference model shows that the bias in elevation amplitude in the finite difference solution is removed in the finite element calculation.     

An intercomparison study of luminescence dating protocols and techniques applied to medieval brick samples from Normandy (France)

A luminescence dating study has been applied to inform the history and archaeology of two early medieval buildings in north western France. Five bricks were sampled from the medieval churches (10th–11th centuries A.D.) of Rugles and Condé-sur-Risle in Normandy. The samples were divided and tested in the luminescence laboratories of the University of Durham (UK) and of Iramat-CRP2A, University of Bordeaux 3 (France). The fine grain and quartz inclusion techniques were applied, and tests included an examination of the anomalous fading of the luminescence signal from fine grain samples and coarse grains of feldspar. With one exception, the dates produced using the fine grain technique, although corrected for fading, were significantly younger than those produced with quartz inclusions. Although most of the corrected fine grain dates were consistent with the medieval construction of the churches, the brick fabric is of Roman type by archaeological assessment, and this is supported by the quartz coarse grain dates. We conclude that the bricks sampled are re-used, likely to be of Roman origin, and that the reliability of measurements with feldspars in brick fabrics requires wider investigation.     

An intercomparison between the GSWM, UARS, and ground based radar observations: a case-study in January 1993

The Global-Scale Wave Model (GSWM) is a steady-state two-dimensional linearized model capable of simulating the solar tides and planetary waves. In an effort to understand the capabilities and limitations of the GSWM throughout the upper mesosphere and thermosphere a comparative analysis with observational data is presented. A majority of the observational data used in this study was collected during the World Day campaign which ran from 20 January to 30 January 1993. During this campaign data from 18 ground-based observational sites across the globe and two instruments located on the UARS spacecraft were analyzed. Comparisons of these data with the simulations from the GSWM indicate that the GSWM results are in reasonable agreement with the observations. However, there are a number of cases where the agreement is not particularly good. One such instance is for the semidiurnal tide in the northern hemisphere, where the GSWM estimates may exceed observations by 50%. Through a number of numerical simulations, it appears that this discrepancy may be due to the eddy diffusivity profiles used by the GSWM. Other differences relating to the diurnal tide and the quasi-two-day wave are presented and discussed. Additionally, a discussion on the biases and aliasing difficulties which may arise in the observational data is alos presented.     

Accuracy of tretyakov precipitation gauge: Result of wmo intercomparison

The Tretyakov non-recording precipitation gauge has been used historically as the official precipitation measurement instrument in the Russian (formerly the USSR) climatic and hydrological station network and in a number of other European countries. From 1986 to 1993, the accuracy and performance of this gauge were evaluated during the WMO Solid Precipitation Measurement Intercomparison at 11 stations in Canada, the USA, Russia, Germany, Finland, Romania and Croatia. The double fence intercomparison reference (DFIR) was the reference standard used at all the Intercomparison stations in the Intercomparison. The Intercomparison data collected at the different sites are compatible with respect to the catch ratio (measured/DFIR) for the same gauge, when compared using mean wind speed at the height of the gauge orifice during the observation period. The Intercomparison data for the Tretyakov gauge were compiled from measurements made at these WMO intercomparison sites. These data represent a variety of climates, terrains and exposures. The effects of environmental factors, such as wind speed, wind direction, type of precipitation and temperature, on gauge catch ratios were investigated. Wind speed was found to be the most important factor determining the gauge catch and air temperature had a secondary effect when precipitation was classified into snow, mixed and rain. The results of the analysis of gauge catch ratio versus wind speed and temperature on a daily time step are presented for various types of precipitation. Independent checks of the correction equations against the DFIR have been conducted at those Intercomparison stations and a good agreement (difference less than 10%) has been obtained. The use of such adjustment procedures should significantly improve the accuracy and homogeneity of gauge-measured precipitation data over large regions of the former USSR and central Europe.     

A sediment trap intercomparison study in the Santa Barbara Basin

Four sediment traps of radically different design were deployed in the Santa Barbara Basin for approximately 45 days. The measured fluxes ranged from 370 to 774 g m^?2 yr^?1 for the different designs. These values lie within flux measurements previously determined for the basin. Compared to the 25-year record (920 g m^?2 yr^?1), however, all fluxes determined in this experiment are somewhat low. Because this experiment was conducted during a general period of high storm activity and runoff, measurement of greater than average flux was expected. It is probable that the higher flux recorded by the sediments results from a significant input of detritus into the basin by near bottom transport.The chemical composition of trapped material was nearly identical in all four trap designs. The deep cone design, however, had a significantly lower Mn content. Since this trap was the only one in which reducing conditions were produced in the sample container, reduction and mobilization of manganese after collection is believed to have occurred.In spite of the very different designs tested, the factor of two agreement in flux determination and the compositional similarity of the material collected is encouraging for future attempts to directly measure the flux of particulates in the ocean.     

Glyphosate persistence in seawater

Glyphosate is one of the most widely applied herbicides globally but its persistence in seawater has not been reported. Here we quantify the biodegradation of glyphosate using standard “simulation” flask tests with native bacterial populations and coastal seawater from the Great Barrier Reef. The half-life for glyphosate at 25 °C in low-light was 47 days, extending to 267 days in the dark at 25 °C and 315 days in the dark at 31 °C, which is the longest persistence reported for this herbicide. AMPA, the microbial transformation product of glyphosate, was detected under all conditions, confirming that degradation was mediated by the native microbial community. This study demonstrates glyphosate is moderately persistent in the marine water under low light conditions and is highly persistent in the dark. Little degradation would be expected during flood plumes in the tropics, which could potentially deliver dissolved and sediment-bound glyphosate far from shore.     

An improvement to linear‐elastic procedures for seismic performance assessment

An improved linear‐elastic analysis procedure is developed in this paper as a simple approximate method for displacement‐based seismic assessment of the existing buildings. The procedure is mainly based on reducing the stiffness of structural members that are expected to respond in the inelastic range in a single global iteration step. Modal spectral displacement demands are determined from the equal displacement rule. Response predictions obtained from the proposed procedure are evaluated comparatively by using the results of benchmark nonlinear response history analysis, and both the conventional and the multi‐mode pushover analyses. In comparative evaluations, a twelve‐story RC plane frame and a six‐story unsymmetrical‐plan RC frame are employed by using 91 ground motion components. It is observed that the proposed procedure estimates the flexural deformation demands in deformation‐controlled members and the shear forces in force‐controlled members with reasonable accuracy. Copyright © 2010 John Wiley & Sons, Ltd.     

An estimate of the Nd isotopic composition of Iapetus seawater from ca. 490 Ma metalliferous sediments

Well-preserved metalliferous sediments and pillow basalts of Lower Ordovician age (ca. 490 Ma) have been studied in an attempt to specify the Nd isotopic composition of Iapetus seawater. Initial¹⁴³Nd/¹⁴⁴Nd ratios of the pillow basalts are indistinguishable from published initial ratios for the 505-Ma Bay of Islands ophiolite complex and are within the anticipated range for MORB-type basalts 500 Ma ago. Metalliferous sediments occur both interstitial to basalt pillows and as well-developed sedimentary accumulations. The initial¹⁴³Nd/¹⁴⁴Nd ratios for the non-interstitial variety range from 0.511851 to 0.511712 (ε_Nd = ?2.7to?5.4) and are considered to provide an estimate of¹⁴³Nd/¹⁴⁴Nd in Iapetus seawater. The interstitial metalliferous sediments show evidence for a significant basalt-derived Nd component. Although volcanic activity occurred at the margin of Iapetus essentially contemporaneous with the formation of the metalliferous sediments, it is clear that arc-type volcanic material was not a major source of Nd in Iapetus seawater. Rather the source of Nd was from continental regions with a similar average age to those supplying material to the present-day Atlantic Ocean.     

Timescales of seawater intrusion and retreat

Quantifying the timescales associated with moving freshwater–seawater interfaces is critical for effective management of coastal groundwater resources. In this study, timescales of interface movement in response to both inland and coastal water level variations are investigated. We first assume that seawater intrusion (SWI) and retreat (SWR) are driven by an instantaneous freshwater-level variation at the inland boundary. Numerical modelling results reveal that logarithmic timescales of SWI (lnT_i) and SWR (lnT_r) can be described respectively by various simple linear equations. For example, SWI timescales are described by lnT_i = a + blnh′_f–s, where a and b are linear regression coefficients and h′_f–s is the boundary head difference after an instantaneous drop of inland freshwater head. For SWR cases with the same initial conditions, but with different increases in freshwater head, lnT_r = c + dΔX_T, where c and d are regression coefficients and ΔX_T is the distance of toe response that can be estimated by a steady-state, sharp-interface analytical solution. For SWR cases with the same freshwater head increase, but with different initial conditions, in contrast, lnT_r = e + flnΔX_T, where e and f are regression coefficients. The timescale of toe response caused by an instantaneous variation of sea level is almost equivalent to that induced by an instantaneous inland head variation with the same magnitude of water level change, but opposite in direction. Accordingly, the empirical equations of this study are also applicable for sea-level variations in head-controlled systems or for simultaneous variations of both inland and coastal water levels. Despite the idealised conceptual models adopted in this study, the results imply that for a particular coastal aquifer, SWI timescales are controlled by the boundary water levels after variations, whereas SWR timescales are dominated by the distance of toe response.     

Dependence of evaporation on meteorological variables at different time-scales and intercomparison of estimation methods

This paper consists of two parts. In the first part, the significance of five major factors, including solar radiation, vapour pressure deficit, relative humidity, wind speed and air temperature, that control evaporation were evaluated comparatively at different time-scales using the data from Changines station in Switzerland. The comparative evaluation was made at hourly, daily, 10-day and monthly time-scales. It was found that the role of controlling variables in evaporation varied with the time-scale. The vapour pressure deficit was best correlated with pan evaporation at all time-scales, while the wind speed was least correlated with pan evaporation, especially when the time period was longer than a day. In the second part, four equations for calculating evaporation, including temperature-based methods, humidity-based methods, mass transfer methods and radiation-based methods, were compared with pan evaporation. Of these four equations, the Penman equation, representing the mass transfer method, resulted in monthly evaporation values that agreed most closely with pan evaporation values. The Romanenko equation, representing the humidity method, also compared reasonably well with pan evaporation. The Turc equation, representing the radiation method, and the Thornthwaite equation, representing the temperature method, were found to underestimate evaporation significantly, especially for cold months. © 1998 John Wiley & Sons, Ltd.     

Neodymium isotopic variations in seawater

New data for the direct measurement of the isotopic composition of neodymium in Atlantic Ocean seawater are compared with previous measurements of Pacific Ocean seawater and ferromanganese sediments from major ocean basins. Data for Atlantic seawater are in excellent agreement with Nd isotopic measurements made on Atlantic ferromanganese sediments and are distinctly different from the observed compositions of Pacific samples. These results clearly demonstrate the existence of distinctive differences in the isotopic composition of Nd in the waters of the major ocean basins and are characteristic of the ocean basin sampled. The average ε_Nd(0) values for the major oceans as determined by data from seawater and ferromanganese sediments are as follows: Atlantic Ocean,ε_Nd(0) ? ?12 ± 2; Indian Ocean,ε_Nd(0) ? ?8 ± 2; Pacific Ocean,ε_Nd(0) ? ?3 ± 2. These values are considerably less than ε_Nd(0) value sources with oceanic mantle affinities indicating that the REE in the oceans are dominated by continental sources. The difference in the absolute abundance of¹⁴³Nd between the Pacific and Atlantic Oceans corresponds to ～10⁶ atoms¹⁴³Nd per gram of seawater. The correspondence between the¹⁴³Nd/¹⁴⁴Nd in seawater and in the associated sediments suggests the possible application of this approach to paleo-oceanography.Distinctive differences in ε_Nd(0) values are observed in the Atlantic Ocean between deep-ocean water associated with North Atlantic Deep Water and near-surface water. This suggests that North Atlantic Deep Water may be relatively well mixed with respect to Nd isotopic composition whereas near-surface water may be quite heterogeneous, reflecting different sources for surface waters relative to deep water. This suggests that it may be possible to distinguish the sources of water masses within an ocean basin on the basis of Nd isotopic composition.The Nd isotopic variations in seawater are used to relate the residence time of Nd and mixing rates between the oceans.     

Inverse modeling for seawater intrusion in coastal aquifers: Insights about parameter sensitivities,variances, correlations and estimation procedures derived from the Henry problem

Inverse modeling studies employing data collected from the classic Henry seawater intrusion problem give insight into several important aspects of inverse modeling of seawater intrusion problems and effective measurement strategies for estimation of parameters for seawater intrusion. Despite the simplicity of the Henry problem, it embodies the behavior of a typical seawater intrusion situation in a single aquifer. Data collected from the numerical problem solution are employed without added noise in order to focus on the aspects of inverse modeling strategies dictated by the physics of variable-density flow and solute transport during seawater intrusion. Covariances of model parameters that can be estimated are strongly dependent on the physics. The insights gained from this type of analysis may be directly applied to field problems in the presence of data errors, using standard inverse modeling approaches to deal with uncertainty in data.