考虑桩土作用独桩海洋平台横向振动特性研究

采用动Winkler弹性地基梁模型模拟桩土问动力相互作用，并考虑了流体与桩问相互作用，通过组合成层土中、水中桩单元的刚度阵，推得了独桩海洋平台连续系统横向振动的动刚度阵及在波浪力作用下平台甲板处的频率响应函数，进而求得了在确定性波浪力及随机波浪力作用下桩身任意点的位移响应。最后，通过算例研究和分析了在随机波浪力作用下成层土参数、甲板上重量及冲刷淘深等因素对平台振动响应的影响。     

桩-网路堤位移应力分析及其应用

由于桩-网复合地基的结构形式比较复杂,难以采用解析法求得其应力和位移。利用有限差分法对某桩-网法路堤进行了数值模拟,并取得了较好结果。计算结果显示,桩间土沉降线为悬链线,与现场位移监测结果吻合较好;桩身弯矩和桩土应力反映了桩-网复合地基的一些受力机理。分析认为,桩间土沉降较大的主要原因是由土体本身压缩及桩侧弯引起的。     

海上风电基础结构动力分析

针对单桩、三桩、四桩导管架3种常规海上风电基础结构型式动力特性展开研究。以模态分析为基础,获得结构整体固有频率和振型;进而综合运用谐响应分析、瞬态分析、谱分析等方法,对基础结构在简谐荷载、冲击荷载、地震荷载及波浪荷载作用下的动力响应特性进行了数值模拟计算和分析。结果显示:本设计中的单桩、三桩、四桩基础结构刚度依次增大,一阶固有频率递增;对于相同的动力荷载激励,基础结构动力响应递减;基础结构设计中既要保证结构具有足够的刚度以满足荷载作用下的变形控制要求,还要使基础刚度适中以避免共振。为海上风电基础结构动力分析提供了参考。     

固定式海洋平台非线性动态响应分析

固定式海洋钢结构平台必须考虑到流体—结构—桩—土的相互作用。桩基式海洋平台是一种大型复杂结构系统,通常包括平台及其上部设备并支持在导管架上,用一组桩通过导管架的腿打入土壤中把它固定在海底。作用在这一结构系统上的有波浪、风、流、设备运行、地震等动载荷。其中以波浪载荷为最重要。对于固定式结构,结构的速度相对于水质点速度不可忽略,因而使波浪力呈非线性性质。桩—土相互作用可用分布的弹簧来表示,其刚度变化根据p-y曲线呈非线性。大多数结构设计在设计载荷下材料处于弹性范围,但在强地震和风暴下允许材料进入非线性而不致结构破坏。本文将一种模态综合技术和模态叠加方法推广应用于研究这一系统的非线性响应分析,假设系统受到规则波作用,波浪力可由波浪理论对给出的设计波算出。采用直接积分法对减缩的动力方程求解,非线性作为伪力矢量移置到方程右端。这样大大节省了计算机存贮及机时。迄今为止,非线性系统的动力分析问题藏缩方法为数有限,由于预测大型复杂结构系统非线性响应耗费巨大的机时相价值昂贵,这一工作显得特别重要。最后由计算程序DAPOS给出的算例表明这一方法的优点并卓有成效。     

钱塘江涌潮区护岸工程的设计及研究

丁坝在江道整治及护岸工程中已有比较广泛的应用。丁坝的平面布置、结构型式与丁坝自身的稳定性及护岸效果密切相关。本文在对钱塘江涌潮区护岸丁坝的设计作了初步总结的基础上,指出了在丁坝结构上存在的一些问题,提出了相应的改进方案,并结合抢险修复工程,进行了现场原型试验。试验结果表明,本文提出的改进方案是切实可行的。     

水平循环荷载作用下单桩动力特性的数值模拟

采用修正的p-y曲线方法，分析了桩基础振动过程中桩土之间由于土体塑性变形导致的桩土脱开现象，给出了计算桩土脱开现象的数值模拟方法，并据此分析计算了中国渤海湾JZ20－2MUQ平台的桩基础动力特性，得到了桩基础振动过程中桩土脱开的区域，分析了桩土之间的脱开对桩基础动力响应的影响等问题。     

大直径超长管桩打桩过程中土塞性状研究

大直径超长桩的可打入分析是海洋平台打桩施工顺利进行的重要保障,土塞是否闭合的判断对于桩基可打入性分析具有较大的影响,因此,合理准确的土塞判断结果对提高桩的可打入分析的准确性具有重要的意义。以现场静力触探(CPTU)试验数据为依据,采用孔扩张理论推导了基于CPTU测试结果的桩端土的极限承载力计算公式;在求解桩端土体承载力时考虑了管桩与土体的刚度差异,同时考虑到打桩过程中的土体扰动。采用Randolph推荐的方法得到了土塞阻力,将两者进行比较,进而判断土塞的状态。通过实际工程的实测数据,对各个土层的土塞状况进行了判别,并根据判别情况采用波动方程的方法对桩基的可打入性进行了分析,将预测结果和现场的打桩记录进行了比较。计算结果显示,提出的方法与实测结果更为接近,有效地提高了桩的可打入性的预测精度。     

海洋平台结构动力响应优化设计与灵敏度分析

研究了海洋平台结构动力响应优化设计以结构动力响应的灵敏度计算方法。给出了结构稳态频率响应和瞬态时程响应的灵敏度分析算法，并通过数值试验讨论了瞬态响应灵敏度分析算法的精度和差分法中变量摄动量的影响。在JIFEX软件中实现了结构动力响应灵敏度计算，建立海洋平台结构优化模型和求解方法。数值算例表明了本文方法和程序的有效性。     

低速运动船只撞击埋置框架结构动力分析模型

通过引入合理的撞击模型,建立了水面运动船只低速撞击埋置框架结构的传递矩阵-节点耦合矩阵动力分析模型。该模型可模拟船只与结构在撞击过程中的短暂脱离,并分析撞击力时程曲线和整个撞击系统的动力响应。与有限元方法的比较验证了结构传递矩阵-节点耦合矩阵动力分析方法的有效性。不同于规范计算方法,分析发现撞击过程中的最大撞击力不仅与船只的初始动能有关,还受船只与结构间的接触刚度及结构的自身刚度影响,这两种刚度越大,则最大撞击力也越大,撞击持续时间则越短,而撞击力时程曲线的振荡越明显,甚至在船只撞击结构后的很短时间内就可能产生较大的撞击力峰值。     

半潜式超大浮体连接器动力特性的一种时间序列分析方法

根据刚性模块弹性连接器 (RMFC)假设研究由 3个模块连接而成的半潜式超大浮体MobileOffshoreBase(MOB)的波浪载荷动力响应。模块和连接器动力响应根据时间序列法计算 ,这种方法包括海况模拟 ,波浪载荷计算和结构响应计算三个主要部分。通过对结构的适当简化 ,根据Airy波理论 ,Morrison公式以及流体中的结构运动方程、弹性连接器变形方程 ,计算求得MOB在不规则海况下的动力响应 ,并将其与相关文献中的结果进行比较 ,表明该方法有良好的精确性     

水下加筋圆柱壳结构声散射特性研究

采用有限元/边界元(FEM/BEM)方法对水下加筋圆柱壳结构的声散射特性进行分析。考虑入射声场激发弹性结构振动产生二次辐射声场,总声场为入射场与散射场之和。基于Mindlin理论建立结构受迫振动的有限元模型,考虑入射声场为简谐激励,采用模态叠加法求出结构振动表面速度。根据声学边界元相关理论,利用有限元方法计算得出的弹性结构表面动力相应,可求出弹性结构的散射声场。研究结果表明,在同一波数下,不加筋结构后向散射强于加筋结构;加筋结构的散射指向性图案分叉较为明显;同种结构在波数增加的时候后向散射强度逐渐增大,前向散射强度逐渐减弱。     

Static and dynamic analyses of three-dimensional hollow concrete block revetments using polyhedral finite element method

In this study, we exploit the flexibility and advantages of polyhedral finite elements in modeling 3D hollow concrete block revetments. In the present method, a new concept is proposed, in which the polyhedral elements are subdivided into sub-tetrahedrons through virtual nodes located at the centroids of the faces and element. Piecewise linear shape functions of polyhedral elements are constructed for the sub-tetrahedrons. Then, the shape functions are used to formulate the stiffness and mass matrices. By this way, the present approach yields lower computational cost than that of the standard polyhedral finite element method based on rational basis functions. The presented method suits well general polyhedral meshes including concave elements, which are used to model 3D complicated structures in design of coastal defenses system protection such as interlocking revetments. Reliability and effectiveness of the present approach are validated by the well-known commercial ANSYS software through static and dynamic analysis.     

Field Test and Numerical Simulation of Tidal Bore Pressures on Sheet-Pile Groin in Qiantang River

A field test of bore pressures on a sheet-pile groin in the Qiantang River was carried out to investigate the characteristics of tidal bore pressures in which temporal and spatial distributions of bore pressures on the sheet-pile groin were obtained through the test. The standard turbulence model was used to simulate the propagation of the tidal bore over a sheet-pile groin with the free surface tracked by the volume of fluid (VOF) method. With the simulated bore pressure over the sheet-pile groin, a finite difference method was used to simulate the dynamic response of the sheet-pile groin subjected to bore pressures. Good agreement between the field test and the simulated results validated the present numerical method. It was found that the bore pressures on the sheet-pile groin varied linearly in the vertical direction and obtained maximum value at the still water level. Bore pressures below the still water level decreased slightly with the depth and were characterized by a trapezoidal distribution.     

基于有限差分法的复合系泊链缆动力模型及其验证

具有链—缆—链结构的复合系泊链缆因其相对于全钢链质量和成本上的优势而在深水系泊中得以广泛应用。基于细长杆理论采用有限差分法建立了可以考虑链—缆—链结构的复合系泊缆数值模型,将其应用于不同工况下全钢链和复合链缆运动的数值模拟中,并开展了验证。首先,将单根钢链顶张力数值模拟结果与不同工况下的模型试验结果进行了对比,验证了数值预报程序应用于全钢链的准确性。然后,对于复合系泊链缆开展了静刚度和动刚度迭代数值模拟,并将模拟结果同已发表文章中的算例结果进行比较,验证了该数值模型在复合链缆模拟上的准确性。发现对于单根钢锚链的验证,激励半径越大,激励周期越小,一个周期内顶张力幅值及其极差越大,钢链运动就越剧烈。对于链—缆—链式复合系泊链缆的验证,发现静刚度迭代中数值模拟结果与算例结果差异较小;对于动刚度迭代,除个别大幅慢漂工况外,两者有较高的吻合;且激励周期越小,激励半径越大,复合系泊链缆顶张力越大,弹性模量越小,运动越剧烈。对于聚酯缆刚度的敏感性分析,发现改变动刚度经验公式参数的情况下,杨氏模量的静刚度迭代和动刚度迭代结果误差分别最大达到了60.81%和68.21%,因此合成纤维材料特性对复合系泊链...     

基于优化设计理论的高桩码头结构振动有限元模型修正

高桩码头是码头建筑物中应用最广泛的结构形式,利用高桩码头物理模型振动测试结果对码头结构有限元模型的修正进行研究。以结构特征灵敏度分析为基础进行了基于优化理论的有限元模型修正。修正后的有限元模型动力特性更趋近于实测值,同时为高桩码头结构的动力响应分析、损伤诊断和整体性评估提供基准。     

Nonlinear response of membranes to ocean waves using boundary and finite elements

The behavior of a highly deformable membrane to ocean waves was studied by coupling a nonlinear boundary element model of the fluid domain to a nonlinear finite element model of the membrane. The hydrodynamic loadings induced by water waves are computed assuming large body hydrodynamics and ideal fluid flow and then solving the transient diffraction/radiation problem. Either linear waves or finite amplitude waves can be assumed in the model and thus the nonlinear kinematic and dynamic free surface boundary conditions are solved iteratively. The nonlinear nature of the boundary condition requires a time domain solution. To implicitly include time in the governing field equation, Volterra's method was used. The approach is the same as the typical boundary element method for a fluid domain where the governing field equation is the starting point. The difference is that in Volterra's method the time derivative of the governing field equation becomes the starting point.The boundary element model was then coupled through an iterative process to a finite element model of membrane structures. The coupled model predicts the nonlinear interaction of nonlinear water waves with highly deformable bodies. To verify the coupled model a large scale test was conducted in the OH Hinsdale wave Research Laboratory at Oregon State University on a 3-ft-diameter fabric cylinder submerged in the wave tank. The model data verified the numerical prediction of the structure displacements and of the changes in the wave field.The boundary element model is an ideal modeling technique for modeling the fluid domain when the governing field equations is the Laplace equation. In this case the nonlinear boundary element model was coupled with a finite element model of membrane structures, but the model could have been coupled with other finite element models of more rigid structures, such as a pontoon floating breakwater.     

Estimation of Land Subsidence Based on Groundwater Flow Model

This article presents an approach for estimating land subsidence due to withdrawal of groundwater. The proposed method calculates the groundwater seepage in 3-D-condition and calculates the land subsidence one-dimensionally. The governing equation on groundwater seepage is based on the three-dimensional mass conservation law and the principle of effective stress. The land subsidence calculation method is derived based on the following assumptions: (1) displacements occur only in the vertical direction, and (2) in vertical direction the total stresses do not change. The governing equation is solved by numerical method, i.e., finite element method (FEM) in spatial discretization and finite difference method (FDM) in time series discretization. In FEM Galerkin method is adopted and in FDM, lumped matrix method is employed. The proposed method is calibrated via analyzing 1-D consolidation problem and the results are compared with those from Terzaghi's one-dimensional consolidation theory and oedometer test. The proposed method is employed to analyze the consolidation of a soft layer due to withdrawal of groundwater from an aquifer under it. Moreover, this method is also applied to a field case of land subsidence due to groundwater pumping in a gas production field in Japan. The analytical results are compared with the field observed data. The results show that this approach simulates the field case well.     

Estimation of Land Subsidence Based on Groundwater Flow Model

This article presents an approach for estimating land subsidence due to withdrawal of groundwater. The proposed method calculates the groundwater seepage in 3-D-condition and calculates the land subsidence one-dimensionally. The governing equation on groundwater seepage is based on the three-dimensional mass conservation law and the principle of effective stress. The land subsidence calculation method is derived based on the following assumptions: (1) displacements occur only in the vertical direction, and (2) in vertical direction the total stresses do not change. The governing equation is solved by numerical method, i.e., finite element method (FEM) in spatial discretization and finite difference method (FDM) in time series discretization. In FEM Galerkin method is adopted and in FDM, lumped matrix method is employed. The proposed method is calibrated via analyzing 1-D consolidation problem and the results are compared with those from Terzaghi's one-dimensional consolidation theory and oedometer test. The proposed method is employed to analyze the consolidation of a soft layer due to withdrawal of groundwater from an aquifer under it. Moreover, this method is also applied to a field case of land subsidence due to groundwater pumping in a gas production field in Japan. The analytical results are compared with the field observed data. The results show that this approach simulates the field case well.