The influence of soil properties on the erodibility of Belgian loamy soils: A study based on rainfall simulation experiments

Twenty soils from the Leuven region were tested in the laboratory with a rainfall simulator. Their texture varied from loam to loamy sand. On the basis of the results obtained, they were classified as a function of the runoff and splash erodibility. For every soil, several properties were determined and tentatively used to explain the classifications based on the runoff and splash erodibility. Significant negative correlations were found between silt content, aggregate stability, C_5–10 index, water content at saturation, and cohesion on the one side and erodibility on the other; a positive correlation was found between sand content and erodibility.     

The erodibility of upland soils and the design of preafforestation drainage networks in the United Kingdom

Hydraulic thresholds for erosion of fourteen upland mineral and organic soils were determined in a hydraulic flume. These soils are from areas to be afforested in the United Kingdom. Some of the group are erosion resistant but others are susceptible to erosion once denuded of vegetation; for example, by preafforestation ploughing. These threshold data were required to calibrate a hydraulic model for effective design of preafforestation drainage networks on a variety of soils. However, simple field measures of soil properties indicative of erosion potential would be of value to the forestry industry for management purposes. Consequently, hydraulic threshold data were related by linear regression methods to basic soil properties, including organic content, grain size, bulk density, compression strength and penetration resistance. The investigation concluded that four peat soils are not eroded by clear water velocities up to 5·7 m s⁻¹, although a mineral bedload might induce erosion at lesser current speeds. Penetration resistance is a good field indicator of the degree of humification of the peat soils. Although selected physical parameters contribute resistance to water erosion, an increased organic content is pre-eminent in reducing erosion susceptibility in both organic and mineral soils. Although compressive strength was not indicative of soil erodibility, field measurements of penetration resistance on a variety of soils could be related to hydraulic thresholds of erosion; albeit through the construction of discriminant functions interpolated by eye. Consequently, organic content (laboratory) or penetration resistance (field) might form the basis of classifying upland soils in terms of erodibility. Mineral soils differ widely in terms of their erodibility, so that subject to further consideration, the use of ploughing for forestry cultivation might be appropriate in wider circumstances than presently recommended by the Forests and Water Guidelines. Ploughing should be acceptable on deep peat providing the underlying mineral soil is not exposed in the bottom of the furrow, and furrows are not led from mineral soils on to deep peat. © 1997 John Wiley & Sons, Ltd.     

Laboratory soil piping and internal erosion experiments: evaluation of a soil piping model for low‐compacted soils

Mechanistic models have been proposed for soil piping and internal erosion on well‐compacted levees and dams, but limited research has evaluated these models in less compacted (more erodible) soils typical of hillslopes and streambanks. This study utilized a soil box (50 cm long, 50 cm wide and 20 cm tall) to conduct constant‐head, soil pipe and internal erosion experiments for two soils (clay loam from Dry Creek and sandy loam from Cow Creek streambanks) packed at uniform bulk densities. Initial gravimetric moisture contents prior to packing were 10, 12 and 14% for Dry Creek soil and 8, 12, and 14% for Cow Creek soil. A 1‐cm diameter rod was placed horizontally along the length of the soil bed during packing and carefully removed after packing to create a continuous soil pipe. A constant head was maintained at the inflow end. Flow rates and sediment concentrations were measured from the pipe outlet. Replicate submerged jet erosion tests (JETs) were conducted to derive erodibility parameters for repacked samples at the same moisture contents. Flow rates from the box experiments were used to calibrate the mechanistic model. The influence of the initial moisture content was apparent, with some pipes (8% moisture content) expanding so fast that limited data was collected. The mechanistic model was able to estimate equivalent flow rates to those observed in the experiments, but had difficulty matching observed sediment concentrations when the pipes rapidly expanded. The JETs predicted similar erodibility coefficients compared to the mechanistic model for the more erodible cases but not for the less erodible cases (14% moisture content). Improved models are needed that better define the changing soil pipe cross‐section during supply‐ and transport‐limited internal erosion, especially for piping through lower compacted (more erodible) soils as opposed to more well‐compacted soils resulting from constructing levees and dams. Copyright © 2013 John Wiley & Sons, Ltd.     

The Effects of Hydrophilic Polymer and Soil Salinity on Corn Growth in Sandy and Loamy Soils

The interaction effects of different applied ratios of a hydrophilic polymer (Superab A200) (0, 0.2, 0.6% w/w) under various soil salinity levels (initial salinity, 4 and 8 ms/cm) were evaluated on available water content (AWC), biomass, and water use efficiency for corn grown in loamy sand and sandy clay loam soils. The results showed that the highest AWC was measured at the lowest soil salinity. The application of 0.6% w/w of the polymer at the lowest salinity level increased the AWC by 2.2 and 1.2 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. The analysis of variance of data showed that the effect of salinity was significant on biomass and water use efficiency of corn in the loamy sand and sandy clay loam soils. The highest amounts of these traits were measured in soils with the lowest salinity level. Application of polymer at the rate of 0.6% in the loamy sand soil and at the rate of 0.2% in the sandy clay loam soil resulted in the highest aerial and root biomass and water use efficiency for corn. At these polymer rates the amounts of water use efficiency for corn were 2.6 and 1.7 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. Thus, the use of hydrophilic polymer in soils especially in the sandy soils increases soil water holding capacity, yield, and water use efficiency of plant. On the other hand, decreases the negative effect of soil salinity on plant and helps for irrigation projects to succeed in arid and semi‐arid areas.     

Assessment of soil factors controlling ephemeral gully erosion on agricultural fields

The soil factor is crucial in controlling and properly modeling the initiation and development of ephemeral gullies (EGs). Usually, EG initiation has been related to various soil properties (i.e. sealing, critical shear stress, moisture, texture, etc.); meanwhile, the total growth of each EG (erosion rate) has been linked with proper soil erodibility. But, despite the studies to determine the influence of soil erodibility on (ephemeral) gully erosion, a universal approach is still lacking. This is due to the complex relationship and interactions between soil properties and the erosive process. A feasible soil characterization of EG erosion prediction on a large scale should be based on simple, quick and inexpensive tests to perform. The objective of this study was to identify and assess the soil properties – easily and quickly to determine – which best reflect soil erodibility on EG erosion. Forty‐nine different physical–chemical soil properties that may participate in establishing soil erodibility were determined on agricultural soils affected by the formation of EGs in Spain and Italy. Experiments were conducted in the laboratory and in the field (in the vicinity of the erosion paths). Because of its importance in controlling EG erosion, five variables related to antecedent moisture prior to the event that generated the gullies and two properties related to landscape topography were obtained for each situation. The most relevant variables were detected using multivariate analysis. The results defined 13 key variables: water content before the initiation of EGs, organic matter content, cation exchange capacity, relative sealing index, two granulometric and organic matter indices, seal permeability, aggregates stability (three index), crust penetration resistance, shear strength and an erodibility index obtained from the Jet Test erosion apparatus. The latter is proposed as a useful technique to evaluate and predict soil loss caused by EG erosion. Copyright © 2018 John Wiley & Sons, Ltd.     

Effect of soil properties on erosion by wash and splash

This paper describes laboratory testing of 148 samples collected from Southern Alberta for erosion by wash and splash. Rainfall intensity was held constant during these tests. Soil aggregation was the most significant variable explaining soil loss. The significance of other soil properties, such as organic carbon and clay content is variable, depending on the interrelationships among aggregate stability, organic content, and clay content of particular soils. Variations in erodibility of the major soils examined are explained by the resistance of aggregates to compaction and dispersion. Splash detachment and wash transport are the dominant erosion mechanisms in inter-rill areas.     

Erodibility of soil and organic matter: independence of organic matter resistance to interrill erosion

The enrichment of organic matter in interrill sediment is well documented; however, the respective roles of soil organic matter (SOM) and interrill erosion processes for the enrichment are unclear. In this study, organic matter content of sediment generated on two silts with almost identical textures, but different organic matter contents and aggregations, was tested. Artificial rainfall was applied to the soils in wet, dry and crusted initial conditions to determine the effects of soil moisture and rainfall and drying history on organic matter enrichment in interrill sediment. While erosional response of the soils varied significantly, organic matter enrichment of sediment was not sensitive to initial soil conditions. However, enrichment was higher on the silt with a lower organic matter content and lower interrill erodibility. The results show that enrichment of organic matter in interrill sediment is not directly related to either SOM content or soil interrill erodibility, but is dominated by interrill erosion processes. As a consequence of the complex interaction between soil, organic matter and interrill erosion processes, erodibility of organic matter should be treated as a separate variable in erosion models. Further research on aggregate breakdown, in particular the content and fate of the organic matter in the soil fragments, is required. Copyright © 2007 John Wiley & Sons, Ltd.     

Understanding soil‐pipe flow and its role in ephemeral gully erosion

The role of soil pipeflow in ephemeral gully erosion is not well understood. Experiments were conducted on continuous soil pipes to better understand the role of internal erosion of soil pipes and its relation to ephemeral gully development. Soil beds of 140 cm length, 100 cm width and 20 cm depth had a single soil pipe of different initial sizes (2, 4, 6, 8, and 10 mm diameter) extend from a water reservoir to the outlet. Experiments were run on Providence silt loam and Smithdale loam soils under a constant head of 15 cm established for 30 min. Either the tunnel collapsed or the head could not be maintained. Soil pipes that were initially 2 and 4 mm clogged instantaneously at their mouth and did not exhibit flow, whereas, pipes initially ≥ 6 mm enlarged by 268, 397, and 699% on average for the 6, 8, and 10 mm diameters, respectively. Critical shear stress values were found to be essentially zero, and erodibility values gave erosion indexes that were extremely high. The rapid internal erosion resulted in erratic flow and sediment concentrations with periods of no flow as pipes were temporarily clogged followed by surges of high flow and high sediment concentrations. Tensiometers within 6 cm of the soil pipes did not exhibit pressure increases typically associated with pipe clogging. Flow through 10 mm diameter soil pipes exhibited tunnel collapse for both soils tested. Tunnel collapse typically occurred within minutes of flow establishment suggesting that ephemeral gullies could be misinterpreted as being caused by convergent surface flow if observations were made after the runoff event instead of when flow is first established through soil pipes. Copyright © 2011 John Wiley & Sons, Ltd.     

Simulations of water movement and solute transport through different soil texture configurations under negative‐pressure irrigation

This study examined the effects of different soil texture configurations on water movement and solute transport to provide a reliable scientific basis for the application of negative‐pressure irrigation (NPI) technology. HYDRUS‐2D was used to analyse water movement and solute transport under NPI. The main results are as follows: (a) HYDRUS‐2D can be used to simulate water movement and solute transport under NPI, as there was good agreement between the simulated and measured values for water contents, NaCl concentrations, cumulative water infiltration, and wetting distances in the horizontal and vertical directions; the Nash–Sutcliffe efficiency coefficients were in the range of 0.94–0.97. (b) Layered soils have obvious effects on water movement under NPI. With the emitter position in the loam layer, when a coarse texture of loamy sand was present below the loam layer (namely, L‐LS), irrigation water accumulated in the topsoil, and this led to an increase in evaporation compared with the homogeneous loam profile. However, fine texture silty loam or silty clay loam layers beneath the loam layer (namely, L‐SiL or L‐SiCL, respectively) was more conducive to water infiltration into the lower layer, and this increased the amount of water infiltration and simultaneously reduced the surface evaporation effectively. (c) Layered soils have obvious effects on solute transport under NPI, and salt accumulation will readily occur in the clay‐rich soil layer at the interface. The maximum soil salt accumulation of L‐LS occurred above the soil interface between the two soil layers with a value of 21.80 g/kg; however, for L‐SiCL and L‐SiL, the maximum salt accumulation occurred below the soil interface between the two soil layers, with values of 23.80 g/kg and 20.08 g/kg, respectively. (d) Interlayered soils showed remarkable changes in the water infiltration characteristics and salt‐leaching intensities under NPI, and the properties for the soil profile with a silty loam interlayer were better than those for the soil profile with a silty clay loam interlayer. The soil profile with a loamy sand interlayer had the lowest amount of water infiltration, which resulted in reductions of the salt‐leaching intensities. Thus, NPI is clearly not suitable for loamy sand soil. Overall, the results demonstrated that soil texture configurations affected water movement and solute transport under NPI. Therefore, careful consideration should be given to the use of NPI to achieve target soil water and solution conditions and reduce water loss.     

An analysis of soil crust strength in relation to potential abrasion by saltating particles

Wind erosion depends on the ease with which particles can be detached from the soil surface, but suitable tests to characterize this property are not available. Two possible methods to determine surface soil strength in the field were therefore compared on a range of artificially ‘crusted’ surfaces. These were made by spraying or tension wetting aggregates (10–2, 2–0.5 and <0.5 mm) from a structurally unstable sandy loam, followed by drying. Each test involved measuring the force exerted on a probe driven at a steady rate into the surface, using either a flat-tipped 0.6 mm diameter penetrometer or a flat-ended cylindrical punch with inner and outer diameters of 5 and 6 mm, respectively. Both probes showed that crusts could be produced reproducibly. Depending on the probe and aggregate size, penetration mainly occurred either as a result of aggregates being deflected out of the pathway of the probe or by genuine rupture of aggregates or of the crusted surface. The penetrometer, because it was comparable to the size of sand grains, gave results that can be used to characterize surface erodibility to saltating particles. The punch gave results that would be unsuitable for this purpose, as would other strength tests that are on too large a scale. Penetrometer results were analyzed to calculate the energy required for penetration. It was thus possible to demonstrate that only the spray-wetted fine aggregates had a surface that could undergo large-scale rupture by saltating sand grains. For all other surfaces, saltating particles would be unable to supply sufficient energy to rupture aggregates or the crusted surface. Erosion could only occur by a slower process of abrasion in which smaller particles or aggregates are chipped away from the surface. However, it is shown that saltating particles could rupture the interaggregate bonding in the 2–0.5 mm aggregate surfaces, thus permitting creep. An alternative and potentially simpler way of characterizing surface erodibility by using a surface modulus of elasticity is also discussed. Our results demonstrate that the small diameter penetrometer is a promising technique for characterizing erodibility of aggregated and crusted surfaces. © 1997 by John Wiley & Sons, Ltd.     

Time-dependency of runoff velocity and erosion the effect of the initial soil moisture profile

The paper reports on experiments carried out to evaluate the effect of the initial soil moisture profile on temporal variations in runoff erosion rate. The moisture profile was varied by applying infrared heating to the soil sample surface over various time periods, while runoff erosivity was varied by varying the slope of the flume. The experiment confirms that dry loamy soils are very erodible: on a slope length of only 4.3 m long sediment concentrations are near transporting capacity in case of a dry soil sample. It appears that temporal variations in sediment concentrations can be well simulated using a simple relationship between runoff erosion resistance and initial soil moisture content, thereby implicitly assuming that the effect of initial moisture content is persistent over the whole duration of the experiment. The implications of these findings with respect to the modelling of sediment output from larger catchments and the design of experiments on rill erodibility are discussed. The experiments also show that, under the present circumstances, mean velocities in the rills appear to be independent of slope. This finding may be of importance with respect to overland flow routing and deterministic erosion modelling.     

Influence of cryptogamic crust disturbance to wind erosion on sand and loam rangeland soils

A portable field wind tunnel was used to assess the sediment flux rates of loam and sand textured soils in the Mallee region of southeastern Australia. Three levels of crust disturbance (nil, moderate and severe) simulating stock trampling were investigated. The results demonstrated the importance of cryptogamic crusts in binding the soil surface and providing roughness after the soil was moderately disturbed. On the loamy soil, the crust helped maintain sediment flux rates below the erosion control target to 5 g m⁻¹ s⁻¹ for a 65 km h⁻¹ wind measured at 10 m height. Once the crust was severely disturbed, sediment fluxes increased to 1·6 times the erosion target. On the sandy soil, even with no crust disturbance the sediment flux was 1·6 times the erosion control target. Disturbing the crust increased sediment fluxes to a maximum of 6·7 times the erosion control target. Removal of the crust also decreased the threshold wind velocity that resulted in an increase to the risk of erosion from <5 per cent to 20 per cent. © 1998 John Wiley & Sons, Ltd.     

Rainfall‐induced consolidation and sealing effects on soil erodibility during concentrated runoff for loess‐derived topsoils

Flume experiments simulating concentrated runoff were carried out on remolded silt loam soil samples (0·36 × 0·09 × 0·09 m³) to measure the effect of rainfall‐induced soil consolidation and soil surface sealing on soil erosion by concentrated flow for loess‐derived soils and to establish a relationship between soil erodibility and soil bulk density. Soil consolidation and sealing were simulated by successive simulated rainfall events (0–600 mm of cumulative rainfall) alternated by periods of drying. Soil detachment measurements were repeated for four different soil moisture contents (0·04, 0·14, 0·20 and 0·31 g g^?1). Whereas no effect of soil consolidation and sealing is observed for critical flow shear stress (τ_cr), soil erodibility (Kc) decreases exponentially with increasing cumulative rainfall depth. The erosion‐reducing effect of soil consolidation and sealing decreases with a decreasing soil moisture content prior to erosion due to slaking effects occurring during rapid wetting of the dry topsoil. After about 100 mm of rainfall, Kc attains its minimum value for all moisture conditions, corresponding to a reduction of about 70% compared with the initial Kc value for the moist soil samples and only a 10% reduction for the driest soil samples. The relationship estimating relative Kc values from soil moisture content and cumulative rainfall depth predicts Kc values measured on a gradually consolidating cropland field in the Belgian Loess Belt reasonably well (MEF = 0·54). Kc is also shown to decrease linearly with increasing soil bulk density for all moisture treatments, suggesting that the compaction of thalwegs where concentrated flow erosion often occurs might be an alternative soil erosion control measure in addition to grassed waterways and double drilling. Copyright © 2007 John Wiley & Sons, Ltd.     

The variation of soil erodibility with slope position in a cultivated canadian prairie landscape

This study examined the variation in soil erodibility along hillslopes in a Prairie landscape. The soil loss produced by simulated rainfall on undisturbed soils was used as an index of relative soil erodibility. Relative erodibility, and several soil properties, were measured at the summit, shoulder, midslope footslope and toeslope of 11 slope transects in an area of cultivated grassland soils on hummocky glacial till. The variation of erodibility with slope position was statistically significant, and slope position explained about 40 per cent of the variation in the erodibility measurements. Erodibility was 14 per cent higher on the shoulder and midslope, and 21 per cent lower on the toeslope, than on the summit and footslope. Local variation in erodibility along slopes was considered to be an important control on patterns of soil erosion in the landscape. The variation of erodibility along the slopes reflected soil property trends. The greatest erodibility was associated with upper slope positions where soils tended to be shallow, coarse, poorly leached and low in organic matter, while lower erodibility was found at lower slope positions with deep, organic-rich and leached soils. Of the individual soil properties considered, silt and sand content were the most highly correlated with erodibility. The results, together with results from other studies, also suggest that net erosion and erodibility are positively related.     

Effects of microbiotic crusts under cropland in temperate environments on soil erodibility during concentrated flow

Several studies illustrate the wind and water erosion‐reducing potential of semi‐permanent microbiotic soil crusts in arid and semi‐arid desert environments. In contrast, little is hitherto known on these biological crusts on cropland soils in temperate environments where they are annually destroyed by tillage and quickly regenerate thereafter. This study attempts to fill the research gap through (a) a field survey assessing the occurrence of biological soil crusts on loess‐derived soils in central Belgium in space and time and (b) laboratory flume (2 m long) experiments simulating concentrated runoff on undisturbed topsoil samples (0.4 × 0.1 m²) quantifying the microbiotic crust effect on soil erosion rates. Three stages of microbiotic crust development on cropland soils are distinguished: (1) development of a non‐biological surface seal by raindrop impact, (2) colonization of the soil by algae and gradual development of a continuous algal mat and (3) establishment of a well‐developed microbiotic crust with moss plants as the dominant life‐form. As the silt loam soils in the study area seal quickly after tillage, microbiotic soil crusts are more or less present during a large part of the year under maize, sugar beet and wheat, representing the main cropland area. On average, the early‐successional algae‐dominated crusts of stage 2 reduce soil detachment rates by 37%, whereas the well‐developed moss mat of stage 3 causes an average reduction of 79%. Relative soil detachment rates of soil surfaces with microbiotic crusts compared with bare sealed soil surfaces are shown to decrease exponentially with increasing microbiotic cover (b = 0·024 for moss‐dominated and b = 0·006 for algae‐dominated crusts). In addition to ground surface cover by vegetation and crop residues, microbiotic crust occurrence can therefore not be neglected when modelling small‐scale spatial and temporal variations in soil loss by concentrated flow erosion on cropland soils in temperate environments. Copyright © 2007 John Wiley & Sons, Ltd.     

Meltwater erosion process of frozen soil as affected by thawed depth under concentrated flow in high altitude and cold regions

Changes in thawed depth of frozen soil caused by diurnal and seasonal temperature fluctuations are commonly found in high altitude and latitude regions of the world. These changes significantly influence hydrologic and erosion processes. Experimental data are necessary to improve the understanding and modeling of the phenomenon. Laboratory experiments were conducted in Beijing to assess the impacts of thawed soil depth, slope gradient, and flow rate on soil erosion by concentrated meltwater flow over an underlying frozen soil layer. Soil samples from watershed were filled in flumes, saturated before being frozen. After the soil was completely frozen, flumes were taken out of storage to thaw the frozen soil from top to the designed depths. Meltwater flow was simulated using a tank filled with water and icecubes at approximately 0°C. The erosion experiments involved four thawed soil depths of 1, 2, 5, and 10 cm; three slope gradients of 5°, 10°, and 15°; and three flow rates of 1, 2, and 4 l/min; and seven rill lengths of 0.5, 1, 2, 3, 4, 5, and 6 m. Sediment‐laden water samples were collected at the lower end of the flume for determination of sediment concentration. The results showed that sediment concentration increased exponentially with rill length to approach a maximum value. The sediment concentrations were closely correlated with thawed soil depth, flow rate, and slope gradient. Shallower thawed depths delivered more sediments than deeper thawed depths. Slope gradient was the primary factor responsible for severe erosion. The effect of flow rate on sediment concentration which decreased with increasing slope gradient, was not as significant as that of slope gradient. Results from these experiments are useful for understanding the effect of thawed soil depth on erosion process in thawed soils subject to freezing and for estimating erosion model parameters. Copyright © 2017 John Wiley & Sons, Ltd.     

Soil redistribution and pedologic transformations in coastal plain croplands

In agricultural basins of the southeastern coastal plain there are typically large disparities between upland soil erosion and sediment delivered to streams. This suggests that colluvial storage and redistribution of eroded soil within croplands is occurring, and/or that processes other than fluvial erosion are at work. This study used soil morphology and stratigraphy as an indicator of erosion and deposition processes in a watershed at Littlefield, North Carolina. Soil stratigraphy and morphology reflect the ways in which mass fluxes associated with cultivation transform the local soils. Fluvial, aeolian and tillage processes were all found to be active in the redistribution of soil. The soil transformations are of five general types. First, erosion and compaction in the cultivated area as a whole result in the thinning of Arenic and Grossarenic Paleudults and Paleaquults to form Arenic, Typic and Aquic Paleudults and Paleaquults. Second, redistribution of surficial material within the fields results in transitions between Arenic and Typic or Aquic subgroups as loamy sand A and E horizons are truncated or accreted. Third, aeolian deposition at forested field boundaries leads to the formation of compound soils with podzolized features. Fourth, sandy rill fan deposits at slope bases create cumulic soils distinct from the loamy sands of the source area or the darker, finer terrace soils buried by the fan deposits. Finally, tillage and fluvial deposition in upland depressions results in the gradual burial of Rains (poorly drained Typic Paleaquults) soils. Results confirm the importance of upland sediment storage and redistribution, and the role of tillage and aeolian processes as well as fluvial processes in the region. Copyright © 1999 John Wiley & Sons, Ltd.     

Soil particle size distribution and induced soil carbon transport by ephemeral gully erosion in Mediterranean mountain arable land

In Mediterranean mountain agroecosystems, soil erosion associated with the development of ephemeral gullies is a common environmental problem that contributes to a loss of nutrient-rich topsoil. Little is known about the influence of ephemeral gully erosion on particle size distribution and its effect on soil organic (SOC) and inorganic (SIC) carbon among different sized soil particles in agricultural soils. In this study, laboratory tests were conducted using velocity settling tube experiments to examine the effects of erosion on sediment particle size distributions from an incised ephemeral gully, associated with an extreme event (235 mm). We also consider subsequent deposition on an alluvial fan in order to assess the distribution of SOC and SIC concentrations and dissolved carbon before and after the extreme event. Soil fractionation was carried out on topsoil samples (5 cm) collected along an ephemeral gully in a cultivated field, located in the lower part of a Mediterranean mountain catchment. The results of this study showed that the sediment transported downstream by runoff plays a key role in the particle size distribution and transportability of soil particles and associated carbon distribution in carbonate rich soils. The eroding sediment is enriched in clay and silt-sized particles at upslope positions with higher SOC contents and gradually becomes coarser and enriched in SIC at the end of the ephemeral gully because the finest particles are washed-out of the study field. The extreme event was associated with an accumulation of dissolved organic carbon at the distal part of the depositional fan. Assessment of soil particle distribution using settling velocity experiments provides basic information for a better understanding of soil carbon dynamics in carbonate rich soils. Processes of soil and carbon transport and relationships between soil properties, erodibility and aggregate stability can be helpful in the development of more accurate soil erosion models. © 2019 John Wiley & Sons, Ltd. © 2019 John Wiley & Sons, Ltd.     

Design of Lysimeter Leak Detector Networks for Surface Impoundments and Landfills

Sampling of soil pore moisture in the vadose zone underneath land disposal facilities (landfills and surface impoundments) for hazardous waste has been suggested as an "early warning system" to detect leakage from these facilities. Some states require vadose zone moisture sampling at such sites. Given a leak of a particular size, mathematical models can estimate the necessary moisture sample volume collection times and lysimeter spacings to guarantee detection of the leak in a homogeneous medium. Examination of 47 hazardous waste sites existing in 1984 indicated the most were located in areas with water tables too shallow to permit vadose zone detection monitoring. Several of the 47 sites had soils that could be described as loamy sand, silt loam or silty clay. Using these three soils as examples, the process of lysimeter leak-detector network design has been illustrated. For a particular loamy sand with a saturates hydraulic conductivity of 10^-6 cm/ sec, the maximum ceramic lysimeter spacing is 15.5 feet at a depth of 30 feet to collec a moisture sample of 10 mL in one week from a 1 ft2 leak. For a silt loam, maximum lysimeter spacing would be 17 feet at depth of 15 feet. For silty clays, the maximum lysimeter spacing is 7 feet at a depth of 2 feet; maximum emplacement depth is about 9 feet. Calculations show that in some soils, suction lysimeters will not be able to collect usable moisture samples. Since soil properties vary widely and lysimeter spacing is strongly dependent on soil-moisture characteristics appropriate soil measurements and modeling must be performed at each disposal facility to estimate lysimete performance and to select locations for emplacement.     

Experimental study of rill bank collapse

Rill bank collapse is an important component in the adjustment of channel morphology to changes in discharge and sediment flux. Sediment inputs from bank collapse cause abrupt changes in flow resistance, flow patterns and downstream sediment concentrations. Generally, bank retreat involves gradual lateral erosion, caused by flow shear stress, and sudden bank collapse, triggered by complex interactions between channel flow and bank and soil water conditions. Collapse occurs when bank height exceeds the critical height where gravitational forces overcome soil shear strength. An experimental study examined conditions for collapse in eroding rill channels. Experiments with and without a deep water table were carried out on a meandering rill channel in a loamy sand and sandy loam in a laboratory flume under simulated rainfall and controlled runon. Different discharges were used to initiate knickpoint and rill incision. Soil water dynamics were monitored using microstandpipes, tensiometers and time domain reflectometer probes (TDR probes). Bank collapse occurred with newly developed or rising pre‐existing water tables near rill banks, associated with knickpoint migration. Knickpoint scour increased effective bank height, caused positive pore water pressure in the bank toe and reduced negative pore pressures in the unsaturated zone to near zero. Matric tension in unsaturated parts of the bank and a surface seal on the ‘interrill’ zone behind the bank enhanced stability, while increased effective bank height and positive pore water pressure at the bank toe caused instability. With soil water contents >35 per cent (sandy loam) and >23 per cent (loamy sand), critical bank heights were 0·11–0·12 m and 0·06–0·07 m, respectively. Bank toe undercutting at the outside of the rill bends also triggered instability. Bank displacement was quite different on the two soils. On the loamy sand, the failed block slid to the channel bed, revealing only the upper half of the failure plane, while on the sandy loam the failed block toppled forwards, exposing the failure plane for the complete bank height. This study has shown that it is possible to predict location, frequency and magnitude of the rill bank collapse, providing a basis for incorporation into predictive models for hillslope soil loss or rill network development. Copyright © 2006 John Wiley & Sons, Ltd.