阿尔泰造山带内韧性剪切带的显微、超显微构造和变形机制

阿尔泰造山带的剪切带中发育大量S-C糜棱岩,其内云母产生云母鱼和扭折构造并发生边界重结晶。长石发生不同性质的系列变形,并以出熔成核为主的动态重结晶为主要变形机制,同时伴有强烈的扩散作用,属Naborrow-Herring蠕变。石英的变形呈条带状并发生完全的旋转和边界迁移动态重结晶。石英晶内变形以位错运动和动态恢复为主,形成亚颗粒构造及动态重结晶,以致产生应变弱化和超塑性变形,定量分析确定的石英变形机制主要为低温幂指数蠕变。     

The Sierra Ballena Shear Zone in the southernmost Dom Feliciano Belt (Uruguay): evolution, kinematics, and deformation conditions

The Sierra Ballena Shear Zone (SBSZ) is part of a high-strain transcurrent system that divides the Neoproterozoic Dom Feliciano Belt of South America into two different domains. The basement on both sides of the SBSZ shows a deformation stage preceding that of the transcurrent deformation recognized as a high temperature mylonitic foliation associated with migmatization. Grain boundary migration and fluid-assisted grain boundary diffusion enhanced by partial melting were the main deformation mechanisms associated with this foliation. Age estimate of this episode is >658 Ma. The second stage corresponds to the start of transpressional deformation and the nucleation and development of the SBSZ. During this stage, pure shear dominates the deformation, and is characterized by the development of conjugate dextral and sinistral shear zones and the emplacement of syntectonic granites. This event dates to 658–600 Ma based on the age of these intrusions. The third stage was a second transpressional event at about 586 to <560 Ma that was associated with the emplacement of porphyry dikes and granites that show evidence of flattening. Deformation in the SBSZ took place, during the late stages, under regional low-grade conditions, as indicated by the metamorphic paragenesis in the supracrustals of the country rocks. Granitic mylonites show plastic deformation of quartz and brittle behavior of feldspar. A transition from magmatic to solid-state microstructures is also frequently observed in syntectonic granites. Mylonitic porphyries and quartz mylonites resulted from the deformation of alkaline porphyries and quartz veins emplaced in the shear zone. Quartz veins reflect the release of silica associated with the breakdown of feldspar to white mica during the evolution of the granitic mylonites to phyllonites, which resulted in shear zone weakening. Quartz microstructures characteristic of the transition between regime 2 and regime 3, grain boundary migration and incipient recrystallization in feldspar indicate deformation under lower amphibolite to upper greenschist conditions (550–400°C). On the other hand, the mylonitic porphyries display evidence of feldspar recrystallization suggesting magmatic or high-T solid-state deformation during cooling of the dikes.     

华北克拉通基底花岗质片麻岩变形和流变学研究——以辽西寺儿堡地区为例

辽西寺儿堡镇新太古代花岗质片麻岩内发育的宏观、微观构造变形特征表明该地区曾遭受了强烈的韧性变形改造。花岗质岩石变形程度在初糜棱岩–糜棱岩之间,岩石经历了SWW向左行剪切作用改造。岩石中石英有限应变测量判别结果表明,构造岩类型为L-S型,为平面应变。岩石的剪应变平均值为1.43,运动学涡度值为0.788~0.829,指示岩石形成于以简单剪切为主的一般剪切变形中。此外,石英颗粒以亚颗粒旋转重结晶和颗粒边界迁移重结晶作用为主,长石颗粒塑性拉长,部分发生膨凸式重结晶作用;石英组构特征(EBSD)揭示石英以中–高温柱面滑移为主;石英颗粒边界具有明显的分形特征,分形维数值为1.151~1.201,指示了中高温变形条件。综合石英、长石的变形行为、石英组构特征以及分形法Kruhl温度计的判别结果,推断辽西寺儿堡镇新太古代花岗质片麻岩经历过480~600℃的中高温变形,其同构造变质相为高绿片岩相-低角闪岩相。花岗质岩石的古差异应力为10.62~12.21 MPa,估算的应变速率为10~(–11.67)~10~(–13.34) s~(–1),即缓慢的变形,可能记录早期中高温、低应变速率的韧性变形过程,反映华北克拉通基底中下部地壳变形特征。     

THE DEFORMATION BEHAVIOUR OF HORNBLENDE IN THE FLORENCE SHEAR ZONE,CENTRAL AUSTRALIA

角闪石在低温变形中通常显示脆性变形行为,通过对中澳洲Ｆｌｏｒｅｎｃｅ剪切带的铁镁质糜棱岩的观察研究表明,角闪石在这些高温变形环境形成的糜棱岩中显示出显著的塑性变形行为,表现在角闪石遭强应变后,无碎裂出现,而具明显的晶内塑性应变现象和强烈的晶体优选定向,角闪石的细粒化是由边界重结晶迁移所致。本文探讨了引起角闪石塑性变形的一些因素,认为岩石发生糜棱岩化时的高温环境增强了角闪石的韧性,几何软化对角闪的塑性变形行为也起到一定的作用。     

东天山康古尔韧性变形带韧性挤压变形特征:以哈密黄山东地区为例

东天山康古尔断裂带和雅满苏断裂带之间石炭纪沉积-火山岩系中发育一条东西向韧性变形带，具两期性质不同的韧性变形，早期韧性挤压性质，晚期右行韧性剪切.对早期韧性挤压变形的宏观构造（糜棱面理、糜棱线理、对称石香肠构造、不对称褶皱等）和显微构造（压力影构造、布丁构造、动态重结晶、不同类型砾石变形特征等）特征做了详细的研究.糜棱岩中砾石有限应变Flinn图解判别岩石类型为L-S和SL型构造岩，三轴应变量的测量均揭示了一般压缩和少部分的平面应变类型.石英亚颗粒旋转重结晶及少量边界迁移重结晶，长石塑性变形、部分膨凸重结晶等变形特征；石英C轴组构揭示中温柱面 < a>和菱面 < a>滑移为主，后期叠加底面 < a>滑移.因此，推测早期韧性挤压变形温度范围在450~550℃.综合区域地质资料，康古尔变形带早期韧性挤压变形形成于300~290 Ma，塔里木板块和中天碰撞闭合后陆内南北挤压环境下.      

糜棱岩化过程中锆石的稳定性 ——以西南三江高黎贡、西盟地区花岗质糜棱岩为例

自然条件下锆石的稳定性对于合理解释锆石年龄及深入理解锆石同位素年代学有重要意义.本文对西南三江造山带高黎贡山和西盟地区的花岗质糜棱岩进行了显微构造和锆石U-Pb年代学研究.高黎贡山和西盟糜棱岩中主要造岩矿物长石、石英、云母发生了明显的变形和重结晶,而锆石则以独立晶体或以残留核的形式保存了原始的岩浆结构.高黎贡山和西盟糜...     

Variscan deformation,microstructural zonation and extensional exhumation of the Moravian Cadomian basement

Abstract

The Cadomian Dyje Batholith, in the foot–wall of the Variscan Moravian nappe pile, has been involved in Variscan ductile deformation. The Cadomian Brunovistulian rocks were obliquely underthrusted during Carboniferous dextral transpression.

Strain intensity is inversely proportional to the distance from the contact of the Variscan thrust front. The microstructures of deformed granodiorites and quartz–diorites show a characteristic zonality marked by relatively high temperature flow in the west (550–580 °C) characterized by dynamic recrystallization of feldspars and grain boundary migration recrystallization of quartz. The size of quartz grains decreases with decreasing strain towards the east. At the easternmost part of the autochthonous Dyje massif, fracturing of feldspar and subgrain rotation recrystallization of quartz predominate. Flow stress estimates calculated from recrystallized quartz grain size show a regional increase of stress intensity from the highly strained margin towards the less deformed core of the Dyje massif. This microstructural zonation is oblique with respect to the major thrust boundary and corresponds roughly to metamorphic isogrades. The microstructural zonation reflects underthrusting of the Brunovistulian domain below the Moldanubian nappe.

The main ductile tectonic event D₁ is followed by a retrogressive brittle–ductile and brittle deformation D₂. D₂ results in the development of shear zones and faults superimposed on the D₁ mylonite fabric. D₂ is related to extension oblique to the D₁ fabric, associated with detachment and the westward movement of the Moravian nappes. © Elsevier, Paris     

Microstructures of deformed grains in the augen gneisses of southern Menderes Massif (western Turkey) and their tectonic significance

A detailed fabric and microstructural analysis of the granitic mylonites was carried out on the southern side of Bes,parmak Mountain north of Selimiye (Milas). The mylonitic augen gneisses have?a blastomylonitic texture characterized by large retort-shape porphyroclasts or augen of feldspars, around which a more ductile, medium to fine-grained matrix of muscovite, biotite, quartz and feldspar is deflected. Feldspars behave in both plastic and brittle fashion, because size reduction occurs through grain boundary migration and/or subgrain rotation, and also through fracturing. Typical “core-and-mantle” structure, characterized by a large feldspar core surrounded by a mantle of fine recrystallized grains, is very characteristic. The majority of plagioclase twins obey the albite-twin law; however, the association with pericline-law twinning suggests that many of the twins are mechanical. Evidence of strain, such as deformation twins, bent or curved twins, undulatory extinction, deformation bands and kink bands occur characteristically in plagioclase. Myrmekite is ubiquitous at K-feldspar grain boundaries, most notably on the long sides of inequant grains parallel to the S-foliation direction, which invariably face the maximum finite shortening direction. Deformation of quartz in mylonitic augen gneisses commonly results in the development of core-and-mantle structure and “type-4” quartz ribbons of elongated, preferably oriented, newly recrystallized quartz aggregates suggesting a primary dynamic recrystallization. Undulatory extinction, deformation bands and lamellae are the strain-related features associated with quartz porphyroclasts. Micas, especially biotite, undergo internal deformation by bend gliding and kinking. Most of the micas are completely attenuated and aligned such that their (001) planes are subparallel or parallel to the margins of quartz ribbons and define the foliation in the rock. These microstructures of feldspars, quartz and mica in the mylonitic augen gneisses in this part of the southern Menderes Massif are broadly consistent with fabric development under upper-greenschist- to lower-amphibolite-facies conditions, rather than almandine–amphibolite facies, as was previously believed. This supports the previous contention of the authors that the protoliths of augen gneisses are younger granitoids and do not represent an exposed Precambrian Pan-African basement in the Menderes Massif.     

Garnet crystal plasticity in the continental crust,new example from south Madagascar

Garnet (10 vol.%; pyrope contents 34–44 mol.%) hosted in quartzofeldspathic rocks within a large vertical shear zone of south Madagascar shows a strong grain‐size reduction (from a few cm to ～300 μm). Electron back‐scattered diffraction, transmission electron microscopy and scanning electron microscope imaging coupled with quantitative analysis of digitized images (PolyLX software) have been used in order to understand the deformation mechanisms associated with this grain‐size evolution. The garnet grain‐size reduction trend has been summarized in a typological evolution (from Type I to Type IV). Type I, the original porphyroblasts, form cm‐sized elongated grains that crystallized upon multiple nucleation and coalescence following biotite breakdown: biotite + sillimanite + quartz = garnet + alkali feldspar + rutile + melt. These large garnet grains contain quartz ribbons and sillimanite inclusions. Type I garnet is sheared along preferential planes (sillimanite layers, quartz ribbons and/or suitably oriented garnet crystallographic planes) producing highly elongated Type II garnet grains marked by a single crystallographic orientation. Further deformation leads to the development of a crystallographic misorientation, subgrains and new grains resulting in Type III garnet. Associated grain‐size reduction occurs via subgrain rotation recrystallization accompanied by fast diffusion‐assisted dislocation glide. This plastic deformation of garnet is associated with efficient recovery as shown by the very low dislocation densities (10¹⁰ m^?3 or lower). The rounded Type III garnet experiences rigid body rotation in fine‐grained matrix. In the highly deformed samples, the deformation mechanisms in garnet are grain‐size‐ and shape‐dependent: dislocation creep is dominant for the few large grains left (>1 mm; Type II garnet), rigid body rotation is typical for the smaller rounded grains (300 μm or less; Type III garnet) whereas diffusion creep may affect more elliptic garnet (Type IV garnet). The P–T conditions of garnet plasticity in the continental crust (≥950 °C; 11 kbar) have been identified using two‐feldspar thermometry and GASP conventional barometry. The garnet microstructural and deformation mechanisms evolution, coupled with grain‐size decrease in a fine‐grained steady‐state microstructure of quartz, alkali feldspar and plagioclase, suggests a separate mechanical evolution of garnet with respect to felsic minerals within the shear zone.     

Deformation of granitic rocks across the brittle-ductile transition

A microstructural analysis has been carried out on mylonites and mylonitic gneisses of the Eastern Peninsular Ranges Mylonite Zone, which were formed over a range of metamorphic conditions from lower greenschist to amphibolite facies. Composite planar fabrics in the form of C and S planes are found at all metamorphic grades. Fractured feldspars, kinked biotites and ductile deformation of quartz characterize the lower greenschist facies mylonites. At mid-upper greenschist grade orthoclase grains show dynamic recrystallization textures whereas plagioclase exhibits low temperature plasticity with only minor recovery. Biotite ribbons form by progressive rotation and coalescence of kink band segments to produce chevron fold patterns. At epidote-amphibolite grade and above, recovery processes and annealing recrystallization predominate in all minerals. Residual orthoclase porphyroclasts show strain-related myrmekite formation along those sides of the grains that face the instantaneous shortening direction. Myrmekite formation due to replacement reactions cannot explain this geometry. It is proposed that the myrmekites formed due to a combination of exsolution, replacement and strain-enhanced diffusion.     

长春东南劝农山地区早二叠世范家屯组岩石变形组构及流变学特征

劝农山地区位于长春市东南部,处于佳-伊断裂和西拉木伦河缝合带交汇处.详细野外调查发现,该区曾遭受强烈韧性剪切变形,剪切带内岩石普遍糜棱岩化,主要由下二叠统范家屯组（P₁f）钙质糜棱岩与侵入其中的燕山期花岗质糜棱岩组成,变形程度处于初糜棱岩至糜棱岩之间,多具有糜棱结构.岩石应变类型主要为压扁型应变,偏一般压缩,为L=S型构造岩,指示其形成于挤压型剪切带的构造环境.多种宏微观韧性剪切变形标志,指示明显的左行剪切运动.电子探针方解石-白云石地质温度计、方解石和石英EBSD组构特征、方解石e双晶形态以及石英长石变形行为等均显示岩石具有低温塑性流变特点,变形环境不超过绿片岩相.剪切带内应变速率偏高,应变集中带应变速率最大,在10-6.95~10-8.89之间,远离强变形带应变速率在10-9.25~10-12.17之间,糜棱岩化作用过程中差异应力下限应大致为51.27~65.46 MPa,代表剪切带糜棱岩化作用为低温中等强度应变,在稍快的应变速率条件下形成.压溶扩散和双晶滑移为劝农山韧性剪切带变形初期的主要变形机制,随着递进变形,逐渐以双晶滑移和晶内滑移为主,递进变形晚期,局部强变形域内发生了粒间滑移.劝农山韧性剪切带形成与早白垩世中晚期伊泽纳崎板块NNW向高斜度斜向俯冲于欧亚大陆之下有关,是佳-伊断裂带左旋走滑事件的局部表现.      

北喜马拉雅穹隆带然巴韧性剪切带石英动态重结晶颗粒的分维几何分析与主要流变参数的估算

位于北喜马拉雅穹隆带东段的然巴构造穹隆外围发育环形韧性剪切带,带内岩石经韧性剪切形成各类糜棱状岩石。石英为带内变形岩中最为常见的造岩矿物,在不同的温度、应变速率下产生不同的显微构造,其中动态重结晶最为常见。重结晶新晶颗粒边界普遍具有锯齿状或港湾状结构,是应变和变形环境的天然记录。新晶粒分维几何统计分析表明:带内动态重结晶石英颗粒边界形态具有自相似性(1≤D≤2),表现出分形特征,分维数值为1.14～1.19,变形温度大约500℃。同构造变质环境属中——高绿片岩相;初步估算古应变速率可能低于10^-9.5S^-1;根据重结晶粒径估算变形古应力6.2～58.8MPa。     

Development of quartz ribbons in quartzofeldspathic granulites

In high-grade (granulite facies) quartzofeldspathic rocks the progressive development of a fabric records contrasting deformation behaviour of quartz and feldspar. Feldspar has undergone deformation mainly by recrystallization-accommodated dislocation creep and produced smaller recrystallized grains progressively in the course of deformation. Quartz has not deformed solely by dislocation creep but also by a diffusion-controlled mechanism. Dislocation climb is important in the dislocation creep of quartz. In contrast to feldspar, quartz grains have not recrystallized into smaller grains at any stage of deformation. Rather, they have transformed initially to short monocrystalline ribbons and ultimately to long polycrystalline ribbons. This textural change of quartz is a continuous process and has taken place in the course of bulk textural change of the rocks during the deformation.     

High-temperature deformation in the Neoproterozoic transpressional Ribeira belt, southeast Brazil

The Neoproterozoic Ribeira belt is subdivided in two domains with contrasting tectonic characteristics. The northern domain is dominated by shallowly dipping foliations and orogen-normal thrust tectonics. The southern domain is characterized by a 1000-km-long network of anastomosing transcurrent shear zones parallel to the belt. This contrast is interpreted as reflecting continent–continent convergence that is almost orthogonal to the margins in the northern domain and significantly oblique in the southern domain. The central, transitional, domain of the Ribeira belt displays the northern termination of the transcurrent shear zone network: the Além Paraíba–Pádua shear zone system (APPSS). The 250-km-long Além Paraíba–Pádua system involves granulites facies mylonites deformed through transpression.A detailed study of the microstructure and lattice preferred orientation (LPO) of the rock-forming minerals in these granulite mylonites allow a better understanding of deformation mechanisms active at high temperature in the crust. Plagioclase crystals are plastically deformed; they display curved twins and cleavages, mechanical twins, and evidence of dynamic recrystallization. LPO of plagioclase is consistent with activation of the (010) [100] and (010) [001] slip systems. LPO of orthopyroxene and amphibole indicates that these minerals have been deformed through dislocation creep with the activation of the (100) [001] slip system. Quartz in granulite mylonite displays evidence of extensive growth through grain boundary migration. The LPO of quartz is therefore the result of a static transformation of an initial, syn-kinematic LPO, and cannot be straightforwardly interpreted in terms of deformation mechanisms active during mylonitization.     

舒兰韧性剪切带应变分析及石英动态重结晶颗粒分形特征与流变参数估算

舒兰北东向韧性剪切带位于佳木斯-伊通断裂带(佳-伊断裂带)中南段, 剪切带内糜棱岩具有明显左行走滑特征, 片麻理产状近NNE向.糜棱岩中长石有限应变Flinn图解判别岩石类型为L-S型构造岩, 属拉长型应变.石英C轴EBSD组构分析表明, 石英组构以中低温菱面为主, 滑移系为{0001} < 110>.剪切带内糜棱岩的剪应变为0.44, 不同方法计算所得运动学涡度值均大于0.95, 指示剪切变形以简单剪切为主.综合矿物变形温度计、石英C轴EBSD组构、石英的粒度-频数图及Kruhl温度计综合估计该韧性剪切带变形机制以位错蠕变机制为主, 变质相为低绿片岩相, 发生韧性变形和糜棱岩化温度范围在400~500 ℃之间.糜棱岩内石英动态重结晶新晶粒边界普遍具有锯齿状或港湾状结构, 利用分形方法对其重结晶新晶边界研究表明, 这些晶粒边界具有自相似性, 表现出分形特征, 分形维数值为1.195~1.220.根据石英重结晶粒径估算差应力值为24.35~27.59 MPa, 代表了舒兰韧性剪切带糜棱岩化作用过程的差异应力下限.使用不同实验方法估算、比较和分析了该剪切带古应变速率, 认为该速率应为10-12.00~10-13.18 s-1, 与区域性应变速率10-13.00~10-15.00 s-1对比, 说明舒兰韧性剪切带的应变速率与世界上大多数韧性剪切带中的糜棱岩应变速率一致, 是缓慢变形的结果, 其形成可能与早白垩世伊泽纳崎板块向欧亚大陆俯冲发生转向有关.      

Microstructural and metamorphic evolution of a high‐pressure granitic orthogneiss during continental subduction (Orlica–Śnieżnik dome,Bohemian Massif)

A microstructural and metamorphic study of a naturally deformed medium‐ to high‐pressure granitic orthogneiss (Orlica–?nie?nik dome, Bohemian Massif) provides evidence of behaviour of the felsic crust during progressive burial along a subduction‐type apparent thermal gradient (～10 °C km^?1). The granitic orthogneisses develops three distinct microstructural types, as follows: type I – augen orthogneiss, type II – banded orthogneiss and type III – mylonitic orthogneiss, each representing an evolutionary stage of a progressively deformed granite. Type I orthogneiss is composed of partially recrystallized K‐feldspar porphyroclasts surrounded by wide fronts of myrmekite, fully recrystallized quartz aggregates and interconnected monomineralic layers of recrystallized plagioclase. Compositional layering in the type II orthogneiss is defined by plagioclase‐ and K‐feldspar‐rich layers, both of which show an increasing proportion of interstitial minerals, as well as the deformation of recrystallized myrmekite fronts. Type III orthogneiss shows relicts of quartz and K‐feldspar ribbons preserved in a fine‐grained polymineralic matrix. All three types have the same assemblage (quartz + plagioclase + K‐feldspar + muscovite + biotite + garnet + sphene ± ilmenite), but show systematic variations in the composition of muscovite and garnet from types I to III. This is consistent with the equilibration of the three types at different positions along a prograde P?T path ranging from <15 kbar and <700 °C (type I orthogneiss) to 19–20 kbar and >700 °C (types II and III orthogneisses). The deformation types thus do not represent evolutionary stages of a highly partitioned deformation at constant P?T conditions, but reflect progressive formation during the burial of the continental crust. The microstructures of the type I and type II orthogneisses result from the dislocation creep of quartz and K‐feldspar whereas a grain boundary sliding‐dominated diffusion creep regime is the characteristic of the type III orthogneiss. Strain weakening related to the transition from type I to type II microstructures was enhanced by the recrystallization of wide myrmekite fronts, and plagioclase and quartz, and further weakening and strain localization in type III orthogneiss occurred via grain boundary sliding‐enhanced diffusion creep. The potential role of incipient melting in strain localization is discussed.     

The effect of deformation on the TitaniQ geothermobarometer: an experimental study

We performed high strain (up to 47 %) axial compression experiments on natural quartz single crystals with added rutile powder (TiO₂) and ~0.2 wt% H₂O to investigate the effects of deformation on the titanium-in-quartz (TitaniQ) geothermobarometer. One of the objectives was to study the relationships between different deformation mechanisms and incorporation of Ti into recrystallized quartz grains. Experiments were performed in a Griggs-type solid-medium deformation apparatus at confining pressures of 1.0–1.5 GPa and temperatures of 800–1,000 °C, at constant strain rates of 1 × 10^?6 or 1 × 10^?7 s^?1. Mobility of Ti in the fluid phase and saturation of rutile at grain boundaries during the deformation experiments are indicated by precipitation of secondary rutile in cracks and along the grain boundaries of newly recrystallized quartz grains. Microstructural analysis by light and scanning electron microscopy (the latter including electron backscatter diffraction mapping of grain misorientations) shows that the strongly deformed quartz single crystals contain a wide variety of deformation microstructures and shows evidence for subgrain rotation (SGR) and grain boundary migration recrystallization (GBMR). In addition, substantial grain growth occurred in annealing experiments after deformation. The GBMR and grain growth are evidence of moving grain boundaries, a microstructure favored by high temperatures. Electron microprobe analysis shows no significant increase in Ti content in recrystallized quartz grains formed by SGR or by GBMR, nor in grains grown by annealing. This result indicates that neither SGR nor moving grain boundaries during GBMR and grain growth are adequate processes to facilitate re-equilibration of the Ti content in experimentally deformed quartz crystals at the investigated conditions. More generally, our results suggest that exchange of Ti in quartz at low H₂O contents (which may be realistic for natural deformation conditions) is still not fully understood. Thus, the application of the TitaniQ geothermobarometer to deformed metamorphic rocks at low fluid contents may not be as straightforward as previously thought and requires further research.     

Macro‐and Microstructural,Textural Fabrics and Deformation Mechanism of Calcite Mylonites from Xar Moron‐Changchun Dextral Shear Zone,Northeast China

The calcite mylonites in the Xar Moron-Changchun shear zone show a significance dextral shearing characteristics. The asymmetric(σ-structure) calcite/quartz grains or aggregates, asymmetry of calcite c-axes fabric diagrams and the oblique foliation of recrystallized calcite grains correspond to a top-to-E shearing. Mineral deformation behaviors, twin morphology, C-axis EBSD fabrics, and quartz grain size-frequency diagrams demonstrate that the ductile shear zone was developed under conditions of greenschist facies, with the range of deformation temperatures from 200 to 300°C. These subgrains of host grains and surrounding recrystallized grains, strong undulose extinction, and slightly curved grain boundaries are probably results of intracrystalline deformation and dynamic recrystallization implying that the deformation took place within the dislocation-creep regime at shallow crustal levels. The calculated paleo-strain rates are between 10~(–7.87)s~(–1) and 10~(–11.49)s~(–1) with differential stresses of 32.63–63.94 MPa lying at the higher bound of typical strain rates in shear zones at crustal levels, and may indicate a relatively rapid deformation. The S-L-calcite tectonites have undergone a component of uplift which led to subhorizontal lifting in an already non-coaxial compressional deformation regime with a bulk pure shear-dominated general shear. This E-W large-scale dextral strike-slip movement is a consequence of the eastward extrusion of the Xing'an-Mongolian Orogenic Belt, and results from far-field forces associated with Late Triassic convergence domains after the final closure of the Paleo-Asian Ocean.     

伸展作用过程中石英变形与重结晶的微观机制

在伸展作用过程中，石英的变形主要表现为三种不同类型变形石英的出现：SGR-R型以中高温条件下的亚颗粒旋转与动态重结晶为主要特点；GBM-R型以中低温条件下的局部颗粒边界迁移与重结晶过程为主；FC型以低温条件下破裂和碎裂作用为主要特点。三种石英变形类型及其变形机制主要受三方面的影响：区域伸展环境的存在；伸展抬升作用过程中变化的p-T条件；变形岩石中的微量流体的参与。     

The role of deformation partitioning in the deformation and recrystallization of plagioclase and K-feldspar in the Woodroffe Thrust mylonite zone, central Australia

ABSTRACT In the Woodroffe Thrust mylonite zone, central Australia, recrystallization in plagioclase and K-feldspar involved subgrain rotation, assisted by grain-boundary or kink band boundary bulging, without contribution from a change in the chemical composition from host grains to new grains. The size of subgrains and new grains changes across the mylonite zone, apparently as a function of the strain rate and the H2O content of the rock. The partitioning of deformation into zones of progressive shearing and progressive shortening controls the sites of recovery and recrystallization in feldspar during mylonitization. The size of feldspar porphyroclasts in well developed mylonites is governed by the scale of deformation partitioning reached in the earlier stages of mylonitization, before the formation of a large proportion of fine-grained matrix that can accommodate the progressive shearing component of the deformation. Recrystallization occurs in microcline, apparently without involving a translation to a monoclinic structure, as microcline-twinned new grains are common adjacent to microcline-twinned host grains. K-feldspar triclinicity values calculated from XRD traces increase from the margins to the interior of the mylonite zone, in conjunction with deformation intensity. K-feldspar host grains locally have cores of orthoclase or untwinned microcline, surrounded by mantles of twinned microcline, suggesting a relationship between the presence of microcline twinning and the degree of K-feldspar triclinicity.