Oil-oil and oil-source rock correlations in the Alpine Foreland Basin of Austria: Insights from biomarker and stable carbon isotope studies

The Alpine Foreland Basin is a minor oil and moderate gas province in central Europe. In the Austrian part of the Alpine Foreland Basin, oil and minor thermal gas are thought to be predominantly sourced from Lower Oligocene horizons (Schöneck and Eggerding formations). The source rocks are immature where the oil fields are located and enter the oil window at ca. 4 km depth beneath the Alpine nappes indicating long-distance lateral migration. Most important reservoirs are Upper Cretaceous and Eocene basal sandstones.Stable carbon isotope and biomarker ratios of oils from different reservoirs indicate compositional trends in W-E direction which reflect differences in source, depositional environment (facies), and maturity of potential source rocks. Thermal maturity parameters from oils of different fields are only in the western part consistent with northward displacement of immature oils by subsequently generated oils. In the eastern part of the basin different migration pathways must be assumed. The trend in S/(S + R) isomerisation of ααα-C₂₉ steranes versus the αββ (20R)/ααα (20R) C₂₉ steranes ratio from oil samples can be explained by differences in thermal maturation without involving long-distance migration. The results argue for hydrocarbon migration through highly permeable carrier beds or open faults rather than relatively short migration distances from the source. The lateral distance of oil fields to the position of mature source rocks beneath the Alpine nappes in the south suggests minimum migration distances between less than 20 km and more than 50 km.Biomarker compositions of the oils suggest Oligocene shaly to marly successions (i.e. Schoeneck, Dynow, and Eggerding formations) as potential source rocks, taking into account their immature character. Best matches are obtained between the oils and units a/b (marly shale) and c (black shale) of the “normal” Schöneck Formation, as well as with the so-called “Oberhofen Facies”. Results from open system pyrolysis-gas chromatography of potential source rocks indicate slightly higher sulphur content of the resulting pyrolysate from unit b. The enhanced dibenzothiophene/phenanthrene ratios of oils from the western part of the basin would be consistent with a higher contribution of unit b to hydrocarbon expulsion in this area. Differences in the relative contribution of sedimentary units to oil generation are inherited from thickness variations of respective units in the overthrusted sediments. The observed trend towards lighter δ¹³C values of hydrocarbon fractions from oil fields in a W-E direction are consistent with lower δ¹³C values of organic matter in unit c.     

Møre Margin: Crustal structure from analysis of Expanded Spread Profiles

Analysis in both the x—t and —p domains of high-quality Expanded Spread Profiles across the Møre Margin show that many arrivals may be enhanced be selective ray tracing and velocity filtering combined with conventional data reduction techniques. In terms of crustal structure the margin can be divided into four main areas: 1) a thicker than normal oceanic crust in the eastern Norway Basin; 2) expanded crust with a Moho depth of 22 km beneath the huge extrusive complex constructed during early Tertiary breakup; 3) the Møre Basin where up to 13–14 km of sediments overlie a strongly extended outer part with a Moho depth at 20 km west of the Ona High; and 4) a region with a 25–27 km Moho depth between the high and the Norwegian coast. The velocity data restricts the continent-ocean boundary to a 15–30 km wide zone beneath the seaward dipping reflector wedges. The crust west of the landward edge of the inner flow is classified as transitional. This region as well as the adjacent oceanic crust is soled by a 7.2–7.4 km s^–1 lower crustal body which may extend beneath the entire region that experienced early Tertiary crustal extension. At the landward end of the transect a 8.5 km s^–1 layer near the base of the crust is recognized. A possible relationship with large positive gravity anomalies and early Tertiary alkaline intrusions is noted.     

Oil/gas–source rock correlations in the Dniepr-Donets Basin (Ukraine): New insights into the petroleum system

The Dniepr-Donets Basin (DDB) hosts a multi-source petroleum system with more than 200 oil and gas fields, mainly in Carboniferous clastic rocks. Main aim of the present study was to correlate accumulated hydrocarbons with the most important source rocks and to verify their potential to generate oil and gas. Therefore, molecular and isotopic composition as well as biomarker data obtained from 12 oil and condensate samples and 48 source rock extracts was used together with USGS data for a geological interpretation of hydrocarbon charging history.Within the central DDB, results point to a significant contribution from (Upper) Visean black shales, highly oil-prone as well as mixed oil- and gas-prone Serpukhovian rocks and minor contribution from an additional Tournaisian source. Devonian rocks, an important hydrocarbon source within the Pripyat Trough, have not been identified as a major source within the central DDB. Additional input from Bashkirian to Moscovian (?) (Shebelinka Field) as well as Tournaisian to Lower Visean rocks (e.g. Dovgal Field) with higher contents of terrestrial organic matter is indicated in the SE and NW part, respectively.Whereas oil–source correlation contradicts major hydrocarbon migration in many cases for Tournaisian to Middle Carboniferous reservoir horizons, accumulations within Upper Carboniferous to Permian reservoirs require vertical migration up to 4000 m along faults related to Devonian salt domes.1-D thermal models indicate hydrocarbon generation during Permo-Carboniferous time. However, generation in coal-bearing Middle Carboniferous horizons in the SE part of the basin may have occurred during the Mesozoic.     

Application of integrated vitrinite reflectance and FAMM analyses for thermal maturity assessment of the northeastern Malay Basin,offshore Vietnam: Implications for petroleum prospectivity evaluation

Several exploration wells have intersected a Cenozoic coal-bearing, fluvial-deltaic mudstone and sandstone succession in the northeastern Vietnamese part of the Malay Basin, and have successfully tested seismically identified direct hydrocarbon indicators (DHIs). The oil and gas/condensate discovery well 46-CN-1x encountered a ∼55 m thick section of lacustrine mudstones having considerable potential as an oil source. Vitrinite reflectance (VR) measurements from these alginite-bearing rocks introduce several problems in thermal maturity evaluation, including associated VR suppression and delineation of cavings and bitumens. Reliable thermal maturity gradients, however, may be established using a combination of conventional VR measurements and ‘equivalent VR’ (EqVR) values derived from the fluorescence alteration of multiple macerals (FAMM) technique. These measurements, performed on dispersed organic matter (DOM) in cuttings from 46-CN-1x, allow separation of low-reflecting bitumens and vitrinite in cavings from indigenous vitrinite and the FAMM results indicate VR suppression of 0.14% in an alginite-bearing mudstone with a high Hydrogen Index value. On the basis of available ‘raw’ VR data, a highly irregular maturity trend is determined, with the deepest sample (2675–2680 m) having a VR of ∼0.4%R_o. The EqVR value, however, for the deepest sample is 0.70%. The maturity trend determined from the FAMM data (and VR data, omitting samples having suppressed VR) indicates that the top of the oil window (VR of 0.75%R_o) is located at about 2800 m depth. Modelling the geothermal gradient using the EASY%R_o algorithm yields ∼40 °C/km for both of the two maturity profiles; this is in the low end of the range for the Malay Basin. Modelled temperature histories indicate onset of hydrocarbon generation for the uppermost Oligocene source rocks between 2 Ma and present-day, which post-dates trap formation. Seismic facies patterns suggest that lacustrine oil-prone units are in the oil window in the same graben complex a few km NW of the investigated well, and these rocks are likely to be the source of the hydrocarbons found in the well. A more widespread occurrence of hydrocarbons sourced from this kitchen is indicated by other discoveries and mapping of DHIs in the area.     

Hydrocarbon prospects across Narmada-Tapti rift in Deccan trap, central India: Inferences from integrated interpretation of magnetotelluric and geochemical prospecting studies

As the Mesozoic sediments contribute most of the oil and gas reserves of the world, we present an integrated interpretation approach using magnetotellurics (MT) and surface geochemical prospecting studies to demarcate hydrocarbon prospective Gondwana (Mesozoic) formations underneath the Deccan flood basalts of Late Cretaceous age across Narmada-Tapti rift (between Bhusawal and Barwah) in Central India. The MT interpretation shows deep (∼5 km) basement structure between southern and central part of the MT profile however, it gradually becomes shallower to either ends of the profile with a predominant basement depth reduction in the northern end compared to the southern end. The geophysical results suggest thick (2-3.5 km) Mesozoic sediments in the area characterized by deep basement structure. The geochemical analysis of the near surface soil samples indicate higher concentrations of light gaseous hydrocarbons constituents over the area marked with thick sub-basalt Mesozoic formations. Analyses of the geochemical data imply that these hydrocarbons are genetically related, generated from a thermogenic source and these samples fall in the oil-producing zone. The temperature-depth estimations in the region supports favorable temperature conditions (80-120 °C) for oil generation at basement depths.     

Alteration and multi-stage accumulation of oil and gas in the Ordovician of the Tabei Uplift,Tarim Basin,NW China: Implications for genetic origin of the diverse hydrocarbons

The Ordovician is the most important exploration target in the Tabei Uplift of the Tarim Basin, which contains a range of petroleum types including solid bitumen, heavy oil, light oil, condensate, wet gas and dry gas. The density of the black oils ranges from 0.81 g/cm³ to 1.01 g/cm³ (20 °C) and gas oil ratio (GOR) ranges from 4 m³/m³ to 9300 m³/m³. Oil-source correlations established that most of the oils were derived from the Mid-Upper Ordovician marine shale and carbonate and that the difference in oil properties is mainly attributed to hydrocarbon alteration and multi-stage accumulation. In the Tabei Uplift, there were three main periods of hydrocarbon accumulation in the late Caledonian stage (ca. 450–430 Ma), late Hercynian stage (ca. 293–255 Ma) and the late Himalayan stage (ca. 12–2 Ma). The oil charging events mainly occurred in the late Caledonian and late Hercynian stage, while gas charging occurred in the late Hercynian stage. During the late Caledonian stage, petroleum charged the reservoirs lying east of the uplift. However, due to a crustal uplifting episode in the early Hercynian (ca. 386–372 Ma), most of the hydrocarbons were transformed by processes such as biodegradation, resulting in residual solid bitumen in the fractures of the reservoirs. During the late Hercynian Stage, a major episode of oil charging into Ordovician reservoirs took place. Subsequent crustal uplift and severe alteration by biodegradation in the west-central Basin resulted in heavy oil formation. Since the late Himalayan stage when rapid subsidence of the crust occurred, the oil residing in reservoirs was exposed to high temperature cracking conditions resulting in the production of gas and charged from the southeast further altering the pre-existing oils in the eastern reservoirs. A suite of representative samples of various crude oils including condensates, lights oils and heavy oils have been collected for detailed analysis to investigate the mechanism of formation. Based on the research it was concluded that the diversity of hydrocarbon physical and chemical properties in the Tabei Uplift was mainly attributable to the processes of biodegradation and gas washing. The understanding of the processes is very helpful to predict the spatial distribution of hydrocarbon in the Tabei Uplift and provides a reference case study for other areas.     

A comparative study between present and palaeo-heat flow in the Qiangtang Basin,northern Tibet,China

The Qiangtang Basin is a significant prospective area for hydrocarbon and gas hydrate resources in the Tibetan Plateau, China. However, relatively little work has been performed to characterise heat flow in this basin, which has restricted petroleum and gas hydrate exploration. In this study, we compare present and palaeo-heat flow in the Qiangtang Basin to provide information on geothermal regime, hydrocarbon generation and permafrost that is necessary for further petroleum and gas hydrate exploration. We base our study on temperature data from a thermometer well, thermal conductivity tests, vitrinite reflectance data, homogenisation temperature data from fluid inclusions, stratigraphic information and a time-independent modelling approach. Our results indicate that in the central Qiangtang Basin, the present thermal gradient is approximately 15.5 °C/km, and heat flow is approximately 46.69 mW/m². Heat flow in the Qiangtang Basin is not relatively stable since the Early Jurassic, as previous research has suggested, and it is generally decreasing with time. Additionally, there is a clear difference between the hottest thermal regime of the southern and northern Qiangtang Depressions during Cretaceous to Pleistocene time. In the southern Qiangtang Depression, the palaeogeothermal gradient is approximately 32.0 °C/km, and palaeo-heat flow is approximately 70 mW/m². However, in the northern Qiangtang Depression, the palaeogeothermal gradient exceeds 81.8 °C/km, and palaeo-heat flow is greater than 172.09 mW/m². The high thermal regime in the northern Qiangtang Depression is driven mainly by hydrothermal convection. Gas reservoirs are possible targets for hydrocarbon exploration in this depression. Currently, the northwestern part of the northern Qiangtang Depression is the most favourable area for gas hydrate exploration in the Qiangtang Basin.     

Mud volcanism and fluid geochemistry in the Cheleken peninsula,western Turkmenistan

A geological and geochemical study has been carried out to investigate the relationships between major mud volcano structures and deep fluid migration in the Cheleken peninsula, in the South Caspian Basin. The fluid geochemistry allowed the origin and migration of the saline waters and the hydrocarbons to be deduced along with the regional source and reservoir rocks. The emitted waters formed by the mixing of deep highly saline water from the main source rocks of the Maykop Fm with the Caspian-like pore water contained in the Pliocene reservoirs. The water composition is very similar to that emitted by the mud volcanoes in Azerbaijan, allowing comparisons to be done between the reservoirs in the western and eastern sides of the South Caspian Basin. The associated oil is derived from a mixed type II/III kerogen deposited in a sub-oxic marine environment and generated during the early oil window. The oil biomarkers indicate that the source rock is the Maykop Fm., as previously determined for the other areas of the South Caspian Basin.The spontaneous emissions, showing different morphologies, are mainly aligned along normal and transtensive fault systems, which provide effective pathways for rapid fluid ascent from deep reservoirs to the surface.     

Geochemical evidence for coal-derived hydrocarbons and their charge history in the Dabei Gas Field, Kuqa Thrust Belt, Tarim Basin, NW China

Large to middle-scale thrust structures are important reservoir plays for coal-derived hydrocarbons in the foreland basins of NW China, with both gas and some accompanying oil. In the Dabei Gas Field of the Kuqa Thrust, however, the oil and gas pools are vertically distributed in a quite unique way: (1) liquid oil and some dissolved gas are present in the Dawanqi Anticline with the reservoir at 300-700 m depth, forming the only oil field in the Kuqa Thrust; (2) gas and minor accompanying oil are found in the deep reservoir of the Dabei-1 and Dabei-2 thrust traps around 5000-6000 m depth; (3) an extremely dry gas pool is found in the Dabei-3 thrust trap where the depth of the reservoir is over 7000 m. Geochemical data suggest that the hydrocarbons in the Dawanqi Anticline and the Dabei thrust traps originated from a similar source, i.e. the underlying Jurassic coal measures, with some contribution from Jurassic lacustrine shales. The Jurassic source rocks did not start to generate oil until the Miocene (around the Kangcun Stage), and extended into the Pliocene (the Kuche Stage) with the main gas generation period in the Pliocene (the Kuche Stage) and the Quaternary. Because the traps formed relatively early, the Dabei-1 and Dabei-2 thrusts could trap some of the early generated oils, but most of the early charged oil was redistributed to the shallower Dawanqi Anticline during the Kuche Stage. The Dabei-3 thrust trap formed concurrently with major gas generation and thus could not trap liquid hydrocarbons. The difference in the vertical distribution of the hydrocarbon accumulations in the Dabei Gas Field resulted from a complex interplay of source variability, structural evolution of the basin and thermal maturation.     

Geochemical overview and undiscovered gas resources generated from Hamitabat petroleum system in the Thrace Basin,Turkey

Since the first drill in 1957, three oil, 19 gas and condensate fields have been discovered in the Thrace Basin. However, any petroleum system with its essential elements and processes has not been assigned yet. This study consists of two parts, (1) geochemical overview of the previous work in order to get a necessary help to construct a petroleum system and (2) calculation of quantitative undiscovered hydrocarbon resources generated from this system. An extensive overview study showed that the primary reservoir and source rocks in the Thrace Basin are the Middle Eocene Hamitabat sandstones and shales, respectively, hence it appears that the most effective petroleum system of the Thrace Basin becomes the Hamitabat (!) petroleum system. Currently, 18.5 billion m³ of in-place gas, 2.0 million m³ (12.7 million bbl) in-place waxy oil as well as minor amount of associated condensate were discovered from this system. This study showed that the regional distribution of the oil and gas fields almost overlapped with the previously constructed pod of active Hamitabat shales implying that short and up-dip vertical migration pathway of hydrocarbons from the source to trapping side was available. Thermal model demonstrated that hydrocarbon generation from the Hamitabat shales commenced in the Early Miocene. The amount of quantitative gas generation based on the mean-original TOC = 0.94 wt%, mean-original HI = 217 HC/g TOC and the volume of the pod of active source rock = 49 km³ is approximately 110 billion m³ of gaseous hydrocarbons that results in a high generation–accumulation efficiency of 17% when 18.5 billion m³ of already discovered hydrocarbons are considered.     

Crustal structure of the South Florida Platform,eastern Gulf of Mexico: An ocean-bottom seismograph refraction study

Five seismic refraction lines, 70–90 km long, were shot in the South Florida Platform region of the Gulf of Mexico using digital ocean-bottom seismographs. Apparent velocities and depths were calculated from the refracted arrivals using a flat-layer model for the region. The two dominant refractors have apparent compressional-wave velocity ranges of 5.6 to 5.9 km s^–1 and 6.2 to 6.7 km s^–1. On the Sarasota Arch, the depth to the top of a 5.8–5.9km/s layer is 3–4 km below sea level. This depth corresponds to the depth to the crystalline basement. The basement dips to the north and to the south from the arch, with velocity of the upper crust increasing from 5.8–5.9 km s^–1 to a maximum of 6.7 km s^–1 at a depth of 6.3 km. Under the continental slope, the crust has presumably been thinned and extended. The deepest refractor has an apparent velocity of about 7.5 km s^–1 at a depth of 25 km. The thickness of the crustal section and the absence of any mantle arrivals in these long refraction profiles on the platform suggest that thick continental crust underlies the South Florida Platform. A north-south cross-section through the platform suggests the presence of two structural highs separated by a portion of the South Florida Basin, which contains at least 5 km of sediment.     

Geological control factors of micro oil distribution in tight reservoirs

Understanding the oil distribution characteristics in unconventional tight reservoirs is crucial for hydrocarbon evaluation and oil/gas extraction from such reservoirs. Previous studies on tight oil distribution characteristics are mostly concerned with the basin scale. Based on Lucaogou core samples, geochemical approaches including Soxhlet extraction, total organic carbon (TOC), and Rock-Eval are combined with reservoir physical approaches including mercury injection capillary pressure (MICP) and porosity-permeability analysis, to quantitatively evaluate oil distribution of tight reservoirs on micro scale. The emphasis is to identify the key geological control factors of micro oil distribution in such tight reservoirs. Dolomicrites and non-detrital mudstones have excellent hydrocarbon generation capacity while detritus-containing dolomites, siltstones, and silty mudstones have higher porosity and oil content, and coarser pore throat radius. Oil content is mainly controlled by porosity, pore throat radius, and hydrocarbon generation capacity. Porosity is positively correlated with oil content in almost all samples including various lithologies, indicating that it is a primary constraint for providing storage space. Pore throat radius is also an important factor, as oil migration is inhibited by the capillary pressure which must be overcome. If the reservoir rock with suitable porosity has no hydrocarbon generation capacity, pore throat radius will be decisive. As tight reservoirs are generally characterized by widely distributed nanoscale pore throats and high capillary pressure, hydrocarbon generation capacity plays an important role in reservoir rocks with suitable porosity and fine pore throats. Because such reservoir rocks cannot be charged completely. The positive correlation between hydrocarbon generation capacity and oil content in three types of high porosity lithologies (detritus-containing dolomites, siltstones, and silty mudstones) supports this assertion.     

Thermal maturity history and petroleum generation modelling for the Lower Cretaceous Abu Gabra Formation in the Fula Sub-basin,Muglad Basin,Sudan

Two petroleum source rock intervals of the Lower Cretaceous Abu Gabra Formation at six locations within the Fula Sub-basin, Muglad Basin, Sudan, were selected for comprehensive modelling of burial history, petroleum maturation and expulsion of the generated hydrocarbons throughout the Fula Sub-basin. Locations (of wells) selected include three in the deepest parts of the area (Keyi oilfield); and three at relatively shallow locations (Moga oilfield). The chosen wells were drilled to depths that penetrated a significant part of the geological section of interest, where samples were available for geochemical and source rock analysis. Vitrinite reflectances (Ro %) were measured to aid in calibrating the developed maturation models.The Abu Gabra Formation of the Muglad Basin is stratigraphically subdivided into three units (Abu Gabra-lower, Abu Gabra-middle and Abu Gabra-upper, from the oldest to youngest). The lower and upper Abu Gabra are believed to be the major source rocks in the province and generally contain more than 2.0 wt% TOC; thus indicating a very good to excellent hydrocarbon generative potential. They mainly contain Type I kerogen. Vitrinite reflectance values range from 0.59 to 0.76% Ro, indicating the oil window has just been reached. In general, the thermal maturity of the Abu Gabra source rocks is highest in the Abu Gabra-lower (deep western part) of the Keyi area and decreases to the east toward the Moga oilfied at the Fula Sub-basin.Maturity and hydrocarbon generation modelling indicates that, in the Abu Gabra-Lower, early oil generation began from the Middle- Late Cretaceous to late Paleocene time (82.0–58Ma). Main oil generation started about 58 Ma ago and continues until the present day. In the Abu Gabra-upper, oil generation began from the end of the Cretaceous to early Eocene time (66.0–52Ma). Only in one location (Keyi-N1 well) did the Abu Gabra-upper reach the main oil stage. Oil expulsion has occurred only from the Abu Gabra-lower unit at Keyi-N1 during the early Miocene (>50% transformation ratio TR) continuing to present-day (20.0–0.0 Ma). Neither unit has generated gas. Oil generation and expulsion from the Abu Gabra source rocks occurred after the deposition of seal rocks of the Aradeiba Formation.     

Hydrocarbons in the Surface Layer of Bottom Sediments in the Northwestern Caspian Sea

The paper presents research results on the concentrations and compositions of aliphatic and polycyclic aromatic hydrocarbons in the surface layer of bottom sediments in the Northwestern Caspian Sea (2014) and compares them to data for sediments of the Middle and Southern Caspian (2012–2013). The seepage of hydrocarbons out of the sediment mass, resulting in abnormally high concentrations of aliphatic hydrocarbons per dry weight (up to 468 μg/g), as well as within the C_org composition (up to 35.2%), is considered the main source of hydrocarbons in sediments in the surveyed area of the Northern Caspian. This is also confirmed by the absence of any correlation between the hydrocarbon and C_org distributions, as well as by the transformed oil composition of high-molecular alkanes. The distribution of markers within polycyclic aromatic hydrocarbons points to a mixed genesis—petrogenic and pyrogenic—with prevalence of the latter. Unlike the shallow-water northern part of the Caspian Sea, the content and composition of hydrocarbons in deep-seated sediments are affected by facial conditions of sedimentation and by matter exchange at the water–bottom interface. Therefore, despite high C_org concentrations (up to 9.9%), sediments in deep-water depressions are characterized by a quite low concentration of aliphatic hydrocarbons (52 μg/g on average; 0.2% of C_org) with prevailing natural allochthonous alkanes.     

Pressure significance of gas chimneys

Analysis was carried out of part of the northern North Sea to test what the presence and style of gas chimneys indicate about fluid pressure (P_f) within hydrocarbon reservoirs. Previous results suggest that broad chimneys above a trap and thin chimneys on the flanks indicate the presence of hydrocarbons, whilst thin chimneys in the crest suggest the hydrocarbons have escaped. Each type of gas chimney is usually associated with overpressure within Mesozoic reservoirs, but the water leg is hydrostatically-pressured in most Cenozoic reservoirs. This indicates: (a) gas leaking from a trap does not necessarily cause P_f to become hydrostatic; (b) overpressure may not be necessary for the expulsion of gasses through seal units to create the chimneys; (c) although gas chimneys indicate the existence of an active hydrocarbon system, their presence does not appear to indicate anything significant about present-day P_f.     

Geological roles of the siltstones in tight oil play

Understanding the hydrocarbon accumulation pattern in unconventional tight reservoirs is crucial for hydrocarbon evaluation and oil/gas extraction from such reservoirs. Previous studies on tight oil accumulation are mostly concerned with self-generation or from source to reservoir rock over short distances. However, the Lucaogou tight oil in Jimusar Sag of Junggar Basin shows transitional feature in between. The Lucaogou Formation comprises fine-grain sedimentary rocks characterized by thin laminations and frequently alternating beds. The Lucaogou tight silt/fine sandstones are poorly sorted. Dissolved pores are the primary pore spaces, with average porosity of 9.20%. Although the TOC of most silt/fine sandstones after Soxhlet extraction is lower than that before extraction, they show that the Lucaogou siltstones in the area of study have fair to good hydrocarbon generation potential (average TOC of 1.19%, average S₂ of 4.33 mg/g), while fine sandstones are relatively weak in terms of hydrocarbon generation (average TOC of 0.4%, average S₂ of 0.78 mg/g). The hydrocarbon generation amount of siltstones, which was calculated according to basin modeling transformation ratio combined with original TOC based on source rock parameters, occupies 16%–72% of oil retention amount. Although siltstones cannot produce the entire oil reserve, they certainly provide part of them. Grain size is negatively correlated with organic matter content in the Lucaogou silt/fine sandstones. Fine grain sediments are characterized by lower deposition rate, stronger adsorption capacity and oxidation resistance, which are favorable for formation of high quality source rocks. Low energy depositional environment is the primary reason for the formation of siltstones containing organic matter. Positive correlation between organic matter content and clay content in Lucaogou siltstones supports this view point. Lucaogou siltstones appear to be effective reservoir rocks due to there relatively high porosity, and also act as source rocks due to the fair to good hydrocarbon generation capability.     

Contrasting Pliocene fluvial depositional systems within the rapidly subsiding South Caspian Basin; a case study of the palaeo-Volga and palaeo-Kura river systems in the Surakhany Suite,Upper Productive Series,onshore Azerbaijan

The South Caspian Basin contains major hydrocarbon reservoirs within the largely Early Pliocene Productive Series. This paper describes and contrasts outcrops of the uppermost ∼500 m of the series (the Surakhany Suite) deposited by two of the main fluvial systems that supplied the Azeri margin of the basin. Sedimentary facies and, for the first time from the Productive Series, palynological analyses document fluvial channel belt complexes, sheetflood overbank and flood plain to flood plain lake environments. The Productive Series on the Apsheron Peninsula, Azerbaijan, was supplied predominantly from the north by the palaeo-Volga river system. It displays an overall fining-upward trend, such that the Surakhany Suite at Lokbatan is dominated by mudstone. Siltstone and coarser-grained sediments make up 28% of the section. Channel bodies are on average 1.5 m thick and form 13% of the succession. In the sub-surface of the Apsheron Peninsula, ratty wireline log responses also indicate that siltstone and sandstone bodies are predominantly thin bedded, with SP-derived net-to-gross sand ratios of ∼0.35–0.40. The succession in the Kura Basin was sourced predominantly from the west by the palaeo-Kura river system. It displays a coarsening-upward trend, such that in the middle and upper Surakhany Suite at Babazanan siltstone and coarser sediments make up 52% of the section. It is characterised by numerous stacked and laterally continuous channel sandstone bodies that are on average 5.8 m thick and comprise 42% of the outcrop. In the sub-surface of the Kura Basin, wireline log responses of the Surakhany Suite have a blocky character and indicate SP-derived net-to-gross sand ratios of 0.26–0.38. These values are similar to calculated sandstone volumes at outcrop (44%). The palynological data, including multivariate analyses, show that the main controls on palynomorph distribution are the degree of fluvial or lacustrine influence, subaerial exposure and salinity. Despite their more lithic nature, Surakhany Suite sandstones derived from the palaeo-Kura river system along the Kurovdag-Babazanan-Neftchala trend have similar or better petrophysical properties than those derived from the palaeo-Volga river on the Apsheron Peninsula and its offshore continuation. This is probably due to their coarser-grain size. This, combined with their greater sandstone body thickness, would suggest that the axis of the Kura Basin forms the most promising part of the Azeri sector of the South Caspian Basin for exploration within the uppermost part of the Productive Series.     

Gas hydrates in the western deep-water Ulleung Basin, East Sea of Korea

Geophysical surveys and geological studies of gas hydrates in the western deep-water Ulleung Basin of the East Sea off the east coast of Korea have been carried out by the Korea Institute of Geoscience and Mineral Resources (KIGAM) since 2000. The work included a grid of 4782 km of 2D multi-channel seismic reflection lines and 11 piston cores 5–8 m long. In the piston cores, cracks generally parallel to bedding suggest significant in-situ gas. The cores showed high amounts of total organic carbon (TOC), and from the southern study area showed high residual hydrocarbon gas concentrations. The lack of higher hydrocarbons and the carbon isotope ratios indicate that the methane is primarily biogenic. The seismic data show areas of bottom-simulating reflectors (BSRs) that are associated with gas hydrates and underlying free gas. An important observation is the numerous seismic blanking zones up to 2 km across that probably reflect widespread fluid and gas venting and that are inferred to contain substantial gas hydrate. Some of the important results are: (1) BSRs are widespread, although most have low amplitudes; (2) increased P-wave velocities above some BSRs suggest distributed low to moderate concentration gas hydrate whereas a velocity decrease below the BSR suggests free gas; (3) the blanking zones are often associated with upbowing of sedimentary bedding reflectors in time sections that has been interpreted at least in part due to velocity pull-up produced by high-velocity gas hydrate. High gas hydrate concentrations are also inferred in several examples where high interval velocities are resolved within the blanking zones. Recently, gas hydrate recoveries by the piston coring and deep-drilling in 2007 support the interpretation of substantial gas hydrate in many of these structures.     

Timing and mechanism of reservoir forming in the Upper Triassic Halahatang Formation,Yuqi block,Tarim Basin,northwestern China

The Yuqi block is an important area for oil and gas exploration in the northern Akekule uplift, Tarim Basin, northwestern China. The Upper Triassic Halahatang Formation (T₃h) within the Yuqi block can be subdivided into a lowstand system tract (LST), a transgressive system tract (TST), and a highstand system tract (HST), based on a study of initial and maximum flood surfaces. Oil in the lowstand system tract of the Halahatang Formation is characterized by medium to lightweight (0.8075 g/cm³–0.9258 g/cm³), low sulfur content (0.41%–1.4%), and high paraffin content (9.65%–10.25%). The distribution of oil and gas is principally controlled by low-amplitude anticlines and faults. Based on studies of fluorescence thin sections and homogenization temperatures of fluid inclusions, reservoirs in the T₃h were formed in at least two stages of hydrocarbon charge and accumulation. During the first stage (Jurassic–Cretaceous) both the structural traps and hydrocarbon reservoirs were initiated; during the second stage (Cenozoic) the structural traps were finally formed and the reservoirs were structurally modified. The reservoir-forming mechanism involved external hydrocarbon sources (i.e. younger reservoirs with oil and gas sourced from old rocks), two directions (vertical and lateral) of expulsion, and multi-stage accumulation. This model provides a theoretical fundament for future oil and gas exploration in the Tarim Basin and other similar basins in northwestern China.     

Present-day stress and pore pressure fields in the Cuu Long and Nam Con Son Basins, offshore Vietnam

Knowledge of the in situ, or contemporary stress field is vital for planning optimum orientations of deviated and horizontal wells, reservoir characterization and a better understanding of geodynamic processes and their effects on basin evolution.This study provides the first documented analysis of in situ stress and pore pressure fields in the sedimentary formations of the Cuu Long and Nam Con Son Basins, offshore Vietnam, based on data from petroleum exploration and production wells.In the Cuu Long Basin, the maximum horizontal stress is mainly oriented in NNW–SSE to N–S in the northern part and central high. In the Nam Con Son Basin, the maximum horizontal stress is mainly oriented in NE–SW in the northern part and to N–S in the central part of the basin.The magnitude of the vertical stress has a gradient of approximately 22.2 MPa/km at 3500 m depth. Minimum horizontal stress magnitude is approximately 61% of the vertical stress magnitude in normally pressured sequences.The effect of pore pressure change on horizontal stress magnitudes was estimated from pore pressure and fracture tests data in depleted zone caused by fluid production, and an average pore pressure–stress coupling ratio (ΔS_h/ΔP_p) obtained was 0.66. The minimum horizontal stress magnitude approaches the vertical stress magnitude in overpressured zones of the Nam Con Son Basin, suggesting that an isotropic or strike-slip faulting stress regime may exist in the deeper overpressured sequences.