基于小波技术的GPS单历元形变信号降噪研究

基于小波变换多分率分析原理,本文阐述了阈值降噪、中值滤波小波降噪原理,在中值滤波基础上通过改进,提出加权中值滤波小波降噪方法。通过仿真实验分别与软硬阈值降噪,中值滤波降噪方法作比较。实验表明,对小波高频系数采用加权中值滤波,然后重构信号,不仅可以最大限度地保留有效信号、有效降噪,保持信号的光滑性,而且具有良好的抗粗差性。     

基于遥感的区域尺度森林地上生物量估算研究

森林是陆地生态系统最大的碳库,精确估算森林生物量是陆地碳循环研究的关键。首先从机载LiDAR数据中提取高度和密度统计量,采用逐步回归模型进行典型样区生物量估算;然后利用机载LiDAR数据估算的生物量作为样本数据,与多光谱遥感数据Landsat8 OLI的波段反射率及植被指数建立回归模型,实现区域尺度森林地上生物量估算。实验结果显示,机载LiDAR数据估算的鼎湖山样区生物量与地面实测生物量的相关性R2达0.81,生物量RMSE为40.85 t/ha,说明机载LiDAR点云数据的高度和密度统计量与生物量存在较高的相关性。以机载LiDAR数据估算的生物量为样本数据,结合多光谱遥感数据Landsat8 OLI估算粤西北地区的森林地上生物量,精度验证结果为:R2为0.58,RMSE为36.9 t/ha;针叶林、阔叶林和针阔叶混交林等3种不同森林类型生物量的估算结果为:R2分别为0.51(n=251)、0.58(n=235)和0.56(n=241),生物量RMSE分别为24.1 t/ha、31.3 t/ha和29.9 t/ha,估算精度相差不大。总体上看,利用遥感数据可以开展区域尺度的森林地上生物量估算,为森林固碳监测提供有力的参考数据。     

Wavelet packets based denoising method for measurement domain repeat-time multipath filtering in GPS static high-precision positioning

Repeatable satellite orbits can be used for multipath mitigation in GPS-based deformation monitoring and other high-precision GPS applications that involve continuous observation with static antennas. Multipath signals at a static station repeat when the GPS constellation repeats given the same site environment. Repeat-time multipath filtering techniques need noise reduction methods to remove the white noise in carrier phase measurement residuals in order to retrieve the carrier phase multipath corrections for the next day. We propose a generic and robust three-level wavelet packets based denoising method for repeat-time-based carrier phase multipath filtering in relative positioning; the method does not need tuning to work with different data sets. The proposed denoising method is tested rigorously and compared with two other denoising methods. Three rooftop data sets collected at the University of Nottingham Ningbo China and two data sets collected at three Southern California Integrated GPS Network high-rate stations are used in the performance assessment. Test results of the wavelet packets denoising method are compared with the results of the resistor–capacitor (RC) low-pass filter and the single-level discrete wavelet transform (DWT) denoising method. Multipath mitigation efficiency in carrier phase measurement domain is shown by spectrum analysis of two selected satellites in two data sets. The positioning performance of the repeat-time-based multipath filtering techniques is assessed. The results show that the performance of the three noise reduction techniques is about 1–46 % improvement on positioning accuracy when compared with no multipath filtering. The statistical results show that the wavelet packets based denoising method is always better than the RC filter by 2–4 %, and better than the DWT method by 6–15 %. These results suggest that the proposed wavelet packets based denoising method is better than both the DWT method and the relatively simple RC low-pass filter for noise reduction in multipath filtering. However, the wavelet packets based denoising method is not significantly better than the RC filter.     

基于LiDAR点云数据索引的DEM快速提取

DEM应用日趋广泛,从LiDAR点云数据中提取DEM是一种满足应用需求的简单有效方法。由于Li-DAR点云数据的庞大性,直接提取DEM效率不高。为了提高对点云数据处理的效率,本文探索应用索引技术来优化LiDAR点云数据的处理,生成高精度DEM。该方法首先对LiDAR原始数据点建立网格分块索引;然后再利用形态学的方法对LiDAR原始数据进行滤波处理;最后用逐点内插方法生成DEM。实验结果表明应用空间数据索引技术极大地提高了点云数据滤波与DEM生成的效率。     

基于小波域的InSAR干涉图噪声识别与估计

为识别InSAR干涉图噪声的类型,从而更有效地进行干涉图处理,提出一种基于小波变换的干涉图噪声类型识别方法。该方法结合小波变换和对数变换算法,从能量和分布特征两个角度,对经小波变换后的InSAR干涉图小波系数的特点进行分析。首先研究低频子带小波系数在对数变换前后的能量分布特点,以此识别干涉图的噪声类型,然后在此基础上利用高频子带系数估计噪声的大小。分析结果显示,干涉图中的噪声为加性噪声,且干涉图高频系数呈高斯正态分布,其噪声大小可用尺度1上的HH子带系数估计。这些结果对在小波域内进行InSAR干涉图噪声的分析与处理具有一定指导意义。     

Accuracy test of point-based and object-based urban building feature classification and extraction applying airborne LiDAR data

Point-based and object-based building extractions were conducted in airborne LiDAR data in a sample area of Buffalo, New York. First, the earth surface points were filtered from the entire laser scan data set using a new filtering algorithm, which combines the TIN slope modelling and statistical analysis. The off-ground points were extracted for buildings in the study area using both point cluster analysis and object-oriented classifications. The accuracies of both approaches were tested using the digitised ground truth. The outcomes of accuracy testing of the point-based method are correctness: 88.74%, completeness: 92.67% and quality: 83.50%. The results of the accuracy of object-based building extraction are correctness: 87.21%, completeness: 60.14%, and quality: 55.26%. Reconstructions of 3D building models based on the extracted building points were performed. This study contributes scientific and technological knowledge for researchers in developing more effective methods in converting the LiDAR survey to a 3D GIS database.     

SAR图像斑点噪声抑制方法与应用研究

通过详细分析SAR图像的判读和应用斑点噪声的算法,得出:多视处理能有效地平滑噪声,但降低空间分辨率;基于空间域滤波算法能有效地平滑斑点噪声,但不同程度地损失边缘和细节信息;基于变换域的小波多尺度滤波可以较好地保持边缘信息,然而其滤波效果不理想。在此基础上提出利用小波分析技术把两种或两种以上的单个滤波方法进行融合,在有效去除斑点噪声时能够较好地保持边缘、细节和纹理信息。最后初步讨论在实际应用中应根据不同情况和要求选择相应的滤波方法。     

基于Kalman滤波的高耸建筑物沉降预测模型研究

为了提高高耸建筑物沉降监测数据的可信性与实时预测的准确性,利用小波分析与Kalman滤波在数据处理方面的优势,采用小波分析先对沉降数据进行去噪,并采用Kalman滤波理论进行预测。通过实验数据的对比分析,结合小波去噪分析与Kalman滤波理论对原始沉降变形量进行沉降预测,能克服只使用单一Kalman滤波方法进行沉降预测中噪声处理的不足,验证了小波分析及结合Kalman滤波理论进行沉降预测的可行性,且预测精度比较高。     

一种新的去除遥感影像混合噪声组合滤波方法

提出了一种三层组合滤波的去噪方法,在小波BayesShrink阈值与自适应中值滤波的基础上增加第三层Wiener滤波,利用Wiener滤波对信噪比高的信号去噪效果好的特点可有效去除残留的混合噪声,为了在去噪过程中保留影像的边缘,在滤波过程中加入了边缘提取算法,对影像的细节进行保留使去噪后的影像更加清晰。试验表明,本文提出的三层滤波方法在去除遥感影像常见的高斯与脉冲混合噪声时,效果要明显优于传统的两层组合滤波算法。     

大坝变形监测数据的小波分析处理方法

引入小波分析方法对大坝变形监测数据的处理,实现了对离散型的变形数据的尺度分解,对变形趋势的分析。并且对变形数据在滤波、消噪等方面,对分解层次中的偶然误差特性分析,以及阀值的选取方法进行了比较,表明利用小波变换的方法对变形数据的分析处理是有效、可行的。     

Geostatistical modeling using LiDAR-derived prior knowledge with SPOT-6 data to estimate temperate forest canopy cover and above-ground biomass via stratified random sampling

Forest canopy cover (CC) and above-ground biomass (AGB) are important ecological indicators for forest monitoring and geoscience applications. This study aimed to estimate temperate forest CC and AGB by integrating airborne LiDAR data with wall-to-wall space-borne SPOT-6 data through geostatistical modeling. Our study involved the following approach: (1) reference maps of CC and AGB were derived from wall-to-wall LiDAR data and calibrated by field measurements; (2) twelve discrete LiDAR flights were simulated by assuming that LiDAR data were only available beneath these flights; (3) training/testing samples of CC and AGB were extracted from the reference maps inside and outside the simulated flights using stratified random sampling; (4) The simple linear regression, ordinary kriging and regression kriging model were used to extend the sparsely sampled CC/AGB data to the entire study area by incorporating a selection of SPOT-6 variables, including vegetation indices and texture variables. The regression kriging model was superior at estimating and mapping the spatial distribution of CC and AGB, as it featured the lowest mean absolute error (MAE; 11.295% and 18.929 t/ha for CC and AGB, respectively) and root mean squared error (RMSE; 17.361% and 21.351 t/ha for CC and AGB, respectively). The predicted and reference values of both CC and AGB were highly correlated for the entire study area based on the estimation histograms and error maps. Finally, we concluded that the regression kriging model was superior and more effective at estimating LiDAR-derived CC and AGB values using the spatially-reduced samples and the SPOT-6 variables. The presented modeling workflow will greatly facilitate future forest growth monitoring and carbon stock assessments for large areas of temperate forest in northeast China. It also provides guidance on how to take full advantage of future sparsely collected LiDAR data in cases where wall-to-wall LiDAR coverage is not available from the perspective of geostatistics.     

基于LiDAR的海岛岸线自动提取研究

为了探讨栅格化方法与图像分割法对海岛岸线提取的效果,本文主要研究了基于Li DAR数据利用这两种方法对某岛进行瞬时海岸线的提取。利用栅格化方法通过对Li DAR点云数据进行粗差剔除、滤波去噪、构建Terrain数据集、创建栅格表面、生成TIN模型及自动生成等高线,从而实现了瞬时海岸线的提取;利用图像分割法是通过对Li DAR点云数据进行粗差剔除、滤波处理、构建TIN模型、生成二值栅格图像、图像处理与图像边缘提取的过程实现瞬时海岸线的提取。对两种方法提取的海岸线进行叠加显示分析,试验结果表明:两种方法提取的海岸线形态结构基本吻合,海岸线提取效率较传统方法均有提高,但栅格化方法提取的海岸线比图像分割方法提取的海岸线更平滑、更细化,边缘信息较为丰富,与实际海岸线更贴切,效果更加理想。     

抗差趋势面的机载LiDAR点云滤波方法

传统曲面约束滤波算法中,利用最小二乘拟合地形曲面易受种子点粗差影响。针对这一问题,提出基于抗差趋势面的机载激光雷达点云数据滤波方法,首先构建格网索引组织数据,引入抗差趋势面拟合合理的区块地形,通过自适应阈值的设置实现不同区域的自动灵活处理,最终滤除孤立点完善滤波结果。使用ISPRS提供的测区数据进行实验,与传统曲面拟合方法进行对比,实验结果证明,该方法较传统移动曲面拟合法能够得到更加可靠的滤波结果,具备较高实用价值。     

基于高程统计方法的机载LiDAR点云数据滤波

提出了一种基于高程统计的LiDAR数据滤波方法,该方法以高程分布统计量为依据,通过迭代的方法逐个滤除,是一种基于原始点云的非监督滤波算法。采用北京凤凰岭地区某块机载LiDAR数据进行实验,并做出了实验改进。实验表明,该方法能够准确有效地滤除地物点,既能较好地保持数据信息量与精度,又不依赖于其他数据源,是一种简单有效的滤波算法。     

基于Car(p,q)模型和数学形态学理论的LiDAR点云数据滤波

在分析现有的LiDAR点云数据后处理方法的基础上,本文提出了一种点云数据“分步”滤波方法。首先对LiDAR点云数据进行数学形态学“粗”滤波,得到“地面点假设”和“非地面点假设”。然后引入顾及因果关系的自回归模型（car）对两类点云数据假设进行模型化处理和假设检验,根据假设检验的结果判断地面点和非地面点,最终得到可靠的分类结果。与单纯的“最小二乘拟合预测法”或“数学形态学”方法相比,这种“分步”处理的思想用于LiDAR点云数据分类处理的结果更可靠。     

建筑物立面分类与DIM点云滤波

针对目前基于近景摄影测量方法构建建筑物立面模型过程中因密集影像匹配（DIM）点云噪声所引起的建筑物立面TIN网格模型畸变问题,本文借鉴机器学习中样本学习的思想,对建筑物立面进行了分类并对DIM点云提出了相应的滤波方法,以达到去除DIM点云噪声和改善其TIN网格模型畸变的目的。其中,针对平面结构立面,采取先对点云样本进行学习计算构建数学立面模型所需参数,再对该立面模型设定阈值并对其点云进行滤波处理的方法;针对曲面结构立面,则结合DIM点云特性先将点云样本分类标记归为立面点与非立面点,再进行样本特征值学习,使用Logistic回归算法迭代计算求解最佳回归系数,从而构建滤波分类器的方法对立面点云进行滤波处理。试验结果表明,本文滤波处理方法能将立面DIM点云噪声有效识别并去除,而且使用该方法处理后所得点云构建的建筑物立面TIN网格模型精细化程度得到有效提高,模型质量得到明显改善。     

多源遥感数据支持下的区域性森林冠层高度估测

结合机载LiDAR数据,提出了一种改进的GLAS光斑点冠层高度地形校正模型,以校正后的GLAS光斑点作为输入样本,结合MODIS遥感影像,利用支持向量回归（SVR）的方法对研究区森林冠层高度进行分生态区估测,并利用野外调查数据和机载LiDAR冠层高度结果对估测结果进行验证。结果显示:研究区的坡度等级直接影响GLAS光斑点森林冠层高度估测精度,改进的地形校正模型可以较好的减小坡度对GLAS光斑点森林冠层高度估测的影响,模型精度RMSE稳定在3.25~3.48 m;不同生态分区的SVR模型估测精度较为稳定,其RMSE=6.41~7.56 m;与算数平均高相比,样地的Lorey's高与制图结果拟合最好,不同生态分区平均估测精度为80.3%。机载LiDAR冠层高度结果的验证平均精度为79.5%,和Lorey's高验证结果呈现较好的一致性。     

Generalization of DEM for terrain analysis using a compound method

This paper reports an investigation into the generalization of a grid-based digital elevation model (DEM) for the purpose of terrain analysis. The focus is on the method of restructuring the grid-based surface elevation data to form a triangulated irregular network (TIN) that is optimized to keep the important terrain features and slope morphology with the minimum number of sample points. The critical points of the terrain surface are extracted from the DEM based on their significance, measured not only by their local relief, but also by their importance in identifying inherent geomorphological and drainage features in the DEM. A compound method is proposed by integrating the traditional point-additive and feature-point methods to construct a drainage-constrained TIN. The outcome is then compared with those derived from other selected methods including filtering, point-additive or feature-point algorithms. The results show that the compound approach is capable of taking advantage of both point-additive and feature-point algorithms to maximally keep the terrain features and to maintain RMSE at an acceptable level, while reducing the elevation data points by over 99%. The analytical result also shows that the proposed method outperforms the compared methods with better control in retaining drainage features at the same level of RMSE.     

干涉复小波复数域双变量滤波算法

针对复小波双变量滤波模型仅考虑小波复系数实部,忽略了系数的虚部,导致信号相位噪声的增加而影响滤波效果的问题,提出基于复小波变换的复数域双变量模型干涉图滤波算法。该算法将双变量贝叶斯估计算法从实数域推广到了复数域,用噪声复系数概率密度函数刻画了小波复系数实部与虚部的相关性,根据小波分解复系数来估计噪声方差和信号方差,建立了复小波复数域双变量滤波模型,求得了干涉图复系数的贝叶斯估计。试验结果表明,本算法对干涉图噪声有较强的抑制能力,保留了干涉图的边缘及细节信息,滤波性能优于传统的实数域复小波双变量滤波、Goldstein滤波、单小波滤波和最优化融合滤波方法。     

基于机载LiDAR数据的区域林木信息提取

本文对LiDAR数据的各种滤波方法以及多次回波特性进行了综合研究,提出一种基于其多次回波特性进行林木信息提取的方法,并对该方法的可行性进行了实例验证,为探索LiDAR数据的应用提供了新的思路。