含气软黏土的不排水抗剪强度计算模型

含气软黏土广泛分布在世界五大洲,大量离散气泡的存在对软黏土的不排水抗剪强度具有强化或损伤作用,然而目前仍缺乏能综合考虑气相强化与气相损伤竞争机制的含气土不排水剪切强度解析表达式。结合临界状态土力学理论,基于笔者提出的含气土屈服函数,建立了v-lnp¢ 空间下临界状态线截距与土体含气特性(u_{w 0},y₀)的数学关系,进而推导了含气软黏土在三轴应力状态下不排水抗剪强度s_u的理论显式表达式。同时,采用所提出的含气软黏土不排水抗剪强度理论计算公式,分别对比了3种典型的含气软黏土在不同含气特性下的不排水抗剪强度理论预测与试验结果,包括马来西亚高岭土、Combwich 黏土和高岭黏土。另外,对比分析了4种不同的含气软黏土不排水抗剪强度理论计算模型的预测误差百分比,证明了提出的基于改进的含气软黏土本构模型的不排水抗剪强度理论计算式的合理性,能够更加准确地同时考虑含气软黏土的气相强化与气相损伤双重效应。     

Simulation of cyclic strength degradation of natural clays via bounding surface model with hybrid flow rule

Strength loss of natural clays subjected to seismic loading is a critical factor contributing to earthquake‐induced ground failure and associated hazards. This work proposes a bounding surface constitutive law to simulate cyclic strength degradation of natural clays resulting from the loss of structure and attendant accumulation of excess pore pressures. The proposed model employs an enhanced plastic flow rule that can simulate accurately the development of pore pressure and explicitly incorporates soil structure effects. The validation of the model with reference to the experimental evidence available for 3 structured clays shows that with a single set of parameters the proposed model can reasonably represent the mechanical behavior of natural clays under various loading conditions (1D compression, monotonic shearing in compression and extension, cyclic loading, and postcyclic shearing). Particularly, its satisfactory performance in terms of quantification of cyclic strength degradation encourages the use of the model in simulating boundary value problems related to the stability of geotechnical facilities under earthquakes.     

Steady‐state solution for cylindrical penetrometers

This paper suggests a new method for obtaining steady‐state solutions for ‘full‐flow’ penetrometers. The method is based on the numerical solution of the small strain plastic‐flow problem (i.e. rigid plastic material) with an inhomogeneous strength field, which is determined by converting changes of material properties over time in a stationary frame of reference into spatial distribution of strength in a moving frame of reference. Rather than building streamlines from back integration of soil element distortion, as previous methods have suggested, the method treats the domain as continuous with the associated field equations. The method employs an upstream weighting technique for the determination of information flow within the domain. The execution order for the calculation is based on topological ordering. This results in the calculation having a complexity of O(N), as compared with O(N^1.5) for the strain path or streamline methods (N is the number of discretized points), which significantly reduces the calculation time. The formulation is presented for the cylindrical (T‐bar) penetrometer, and includes aspects of soil strength degradation, strain rate effects, strength anisotropy, and interface strength law. Comparison to previously published values, based on large displacement finite element simulations with remeshing, showed good agreement, indicating on the correctness of the suggested approach. Investigation into the soil rigid‐body rotation and the remolding effect on anisotropy characteristics showed an interesting behavior, where the decrease of strength anisotropy due to remolding has a greater influence when the soil strength is higher in the vertical direction. Copyright © 2009 John Wiley & Sons, Ltd.     

低含水率非饱和高温冻土模型

在低含水率非饱和土模型的基础上,从冻土物理特性出发,只考虑毛细吸力和附加压力的作用,建立了非饱和高温冻土细观结构模型,并结合相关实验数据资料改进了高温冻土未冻水含量的经验关系式,基此推导出孔隙水压力、有效应力以及抗剪强度随温度、含水量的变化关系. 同时,通过理论计算与实验（实测）结果进行对比分析,发现本模型能够很好地反映非饱和高温冻土的相关物理力学特性,尤其在定性上能够与宏观实测结果相吻合. 最后,基于非饱和高温冻土微观模型,对非饱和高温冻土的有效应力、抗剪强度进行了讨论分析,给出了合理的理论解释,并对高温冻土相关物理力学特性做出了定性的理论预测.     

静三轴试验中水泥土力学特性及本构模型研究

通过不排水三轴压缩试验对水泥土的力学特性进行研究,重点分析了围压与水泥掺入比对水泥土体强度、孔压及刚度的影响。试验结果表明,随着围压与水泥掺入比的增加,水泥土体的强度与刚度均增加,而孔压随之减少;随着轴应变的增加,刚度逐渐减少。而在加载初期,刚度衰减较快,随着轴应变的继续增加曲线渐趋平缓,衰减现象并不明显;随着无量纲化偏应力的增加,无量纲化刚度逐渐减少,并且两者为曲线关系。通过对水泥土的刚度软化规律进行描述,得到了修正的邓肯-张模型。通过对试验曲线进行回归分析确定了模型参数。与实测数据对比发现,该修正模型不仅可以较好地模拟水泥土的应力-应变关系,还体现了水泥土应变软化型曲线的特点。     

A new versatile constitutive law for modelling the monotonic response of soft rocks and structured fine-grained soils

This paper deals with a new critical state–based constitutive model for soft rocks and fine-grained soils. The model, formulated in the single-surface plasticity framework, is characterised by the following main features: (i) a generalised three-invariant yield surface capable of reproducing a wide set of well-known criteria, (ii) the dependency of the elastic stiffness on the current stress state by means of a hyperelastic formulation, (iii) the ability of simulating the plastic strain–driven structure degradation processes by a set of appropriate isotropic hardening laws, and (iv) a nonassociate flow rule in the meridian plane. The adopted formulation is hierarchical, such that the various features of the model can be activated or excluded depending on the specific kind of geomaterial to be modelled and on the quality and quantity of the related available experimental results. The constitutive model was implemented in a commercial finite element code by means of an explicit modified Euler scheme with automatic substepping and error control. The procedure does not require any form of stress correction to prevent drift from the yield surface. The performance of the model is first analysed by means of a wide set of parametric analyses, in order to highlight the main features and to evaluate the sensitivity of the formulation with reference to the input parameters. The model is then adopted to simulate the experimental response observed on three different geomaterials, ranging from soft clays to soft rocks.     

软土抗剪强度指标随固结度变化规律分析

常规的抗剪强度指标黏聚力c和内摩擦角φ无法准确描述堆载作用下任意固结度时软土的力学特性,而现有的考虑软土抗剪强度值随固结度增长的极限平衡法无法得出应力场、位移场等实际工程需要的数据,因此,基于理论推导和室内试验,对堆载作用下软土抗剪强度指标随固结度的变化规律进行了分析。对现有的2个计算公式进行了对比分析,得出它们具有等价性。从孔隙水压力的角度进行分析,提出了新的计算公式,并且得出内摩擦角随固结度单调递增,黏聚力随固结度单调递减的变化规律。当固结度一定且不为100%时,黏聚力与初始固结压力呈线性增长的关系,内摩擦角与其无关。室内试验表明,由于综合考虑了有效应力参数和总应力参数,新推导公式与试验结果吻合得更好,证明了新推导公式正确性和优越性。     

原状膨胀土剪切力学特性的应变速率效应

为研究应变速率对原状膨胀土力学性状的影响,通过GDS三轴试验系统进行了不同速率和围压下的固结不排水三轴剪切试验,分析了应力−应变曲线、孔隙水压力、剪切强度以及破坏模式随应变速率的变化规律。结果表明：不同应变速率下,膨胀土应力−应变曲线均呈应变硬化型。随着应变速率的增加,不排水剪切强度单调递增,引入应变速率参数ρ_0.9后发现,不排水强度增长率为14.3%～23.2%,平均值为18.4%。低围压下,应变速率对孔隙水压力影响较小,随着围压的增大,孔隙水压力的发展趋势由软化型转变为硬化型,孔隙水压力峰值随应变速率的增大而减小。原状膨胀土应变速率效应与其多裂隙性密切相关,破坏形式表现为小应变速率下主剪切带与次剪切带共存,大应变速率下仅有主剪切带,裂隙或多剪切带的出现强化了膨胀土强度的应变速率效应。     

絮凝−真空−电渗联合加固滩涂软土的模型试验研究

针对真空预压作用下排水板淤堵与排水条件受限等问题,提出絮凝−真空−电渗联合加固法。首先通过沉降柱试验确定合适的有机絮凝剂,然后采用该絮凝剂,分别在 48 h（开始介入真空预压,固结度为0 ）、60 h（排水速率明显下降,固结度为60%）及 84 h（排水速率近乎 0,固结度为 80%）时介入电渗,开展不同电渗介入时间的絮凝−真空−电渗联合加固试验。试验从排水量、十字板剪切强度、含水率与孔压等对比分析联合加固的有效性,确定其最佳电渗介入时间。试验结果表明：当固结度为 80% 时介入电渗,絮凝−真空−电渗联合加固法能够有效地抑制排水速率减小的趋势,增长有效排水时间。同时,土体的抗剪强度和承载力亦得到大幅提升,孔压消散更加均匀。此外,在阳离子聚丙烯酰胺絮凝剂的作用下,初始排水速率快,在一定程度上使土体的渗透性得到提升,有效地解决了排水板淤堵问题,说明絮凝−真空−电渗联合加固法具有较强的优越性。     

聚丙烯纤维复合土抗裂补强特性试验研究

将聚丙烯纤维按不同类型、不同组合、不同含量掺入土中的三轴压缩试验,研究了聚丙烯纤维复合土的应力-应变性状及对复合土强度特性的影响。试验结果表明,加固黏性土要选择分散性好的束状单丝聚丙烯纤维,而不是网状聚丙烯纤维,聚丙烯纤维按占土质量0.2%时为最佳掺入量,束状单丝聚丙烯纤维长度为6 mm+10 mm+15 mm+19 mm的4种组合较为理想,可使聚丙烯纤维复合土微结构联结强度得到明显改善,抗裂补强,黏性土抗剪强度得到极大的提高。     

考虑试验阻尼效应的一种土体动力双型抛物线本构模型

针对土动力试验中土体反向卸载（或加载）曲线形状有时表现为先变化平缓后变化剧烈这一特征,基于土体实验结果的 和 曲线,建立了不规则荷载作用下可调的双型抛物线形式的本构曲线规则,阐述了A型和B型抛物线的函数表达式及实现过程。采用9种方法对试验阻尼比的模拟对比,表明所建立的加卸载准则尤其能准确拟合试验阻尼值,是对广义Masing准则的一种简化及实用化。由于调制因子 的可变性,它具有更强地模拟试验本构曲线形状的能力。针对台湾Lotung DHB钻井台阵试验场地,以等效线性化方法SHAKE91、LSSRLI-1,时域非线性方法DESRA-2、Pyke方法、非Masing准则模型1、“隐式应力阻尼等效”模型、“阻尼比退化系数”模型和非Masing准则模型2以及双型抛物线本构模型等9种方法（或模型）分别进行了非线性地震反应分析,并将结果与强震观测记录进行比较,结果表明,双型抛物线本构模型计算的复合加速度地震动的峰值大小、波形大小相对关系及后续波形,与实际地震记录较相一致,说明了模型的合理性以及实际工程应用的可行性。     

A closed form analytical solution for two‐dimensional plane strain consolidation of unsaturated soil stratum

This paper discusses the excess pore‐air and pore‐water pressure dissipations and the average degree of consolidation in the 2D plane strain consolidation of an unsaturated soil stratum using eigenfunction expansion and Laplace transformation techniques. In this study, the application of a constant external loading on a soil surface is assumed to immediately generate uniformly or linearly distributed initial excess pore pressures. The general solutions consisting of eigenfunctions and eigenvalues are first proposed. The Laplace transform is then applied to convert the time variable t in partial differential equations into the Laplace complex argument s. Once the domain is obtained, a simplified set of equations with variable s can be achieved. The final analytical solutions can be computed by taking a Laplace inverse. The proposed equations predict the two‐dimensional consolidation behaviour of an unsaturated soil stratum capturing the uniformly and linearly distributed initial excess pore pressures. This study investigates the effects of isotropic and anisotropic permeability conditions on variations of excess pore pressures and the average degree of consolidation. Additionally, isochrones of excess pore pressures along vertical and horizontal directions are presented. It is found that the initial distribution of pore pressures, varying with depth, results in considerable effects on the pore‐water pressure dissipation rate whilst it has insignificant effects on the excess pore‐air pressure dissipation rate. Copyright © 2015 John Wiley & Sons, Ltd.     

重塑非饱和粘土抗剪强度参数与饱和度的关系研究

土的饱和度是基于水分状态和密度状态的一个衍生变量。存在因应水分状态变化和因应密度状态变化的两类饱和度变化过程。根据23组不同水分状态和密度状态的UU三轴压缩试验结果,讨论了重塑非饱和粘性土抗剪强度参数与饱和度的关系。数据分析表明:粘聚力与水分状态相关的饱和度的关系是强非线性的,与密度状态相关的饱和度的关系是准线性的。内摩擦角与水分状态相关的饱和度的关系是强非线性的,与密度状态相关的饱和度的关系是弱非线性的。     

基于孔隙面积比的麦秸秆防腐分析及秸秆对粉土抗剪强度的影响

粉土性能不良,需改良后才能在高速公路路基中使用;麦秸秆环保可再生,掺入粉土会起到加筋作用,但自身易被水腐蚀,需防腐后才能使用。本文从孔隙面积比出发,分析聚乙烯醇对秸秆的防腐机理和防腐效果,通过抗拉强度试验分析防腐对秸秆抗拉强度的影响;通过直剪试验分析秸秆对粉土抗剪强度的影响。结果表明:聚乙烯醇通过自身防腐性能的发挥、填充麦秸秆孔隙减小吸水通路、在秸秆表面形成保护膜阻隔水分进入来实现防腐,孔隙面积比越小防腐效果越好;试验范围内,麦秸秆的防腐最佳浸泡时间为4 d,防腐剂最佳溶液浓度为10%,此时秸秆孔隙面积比最小,且防腐耗时最短,或经济最优。麦秸秆长度对孔隙面积比的影响主要在4 d内,与最终孔隙面积比关系不大。防腐麦秸秆抗拉强度提高。秸秆加筋土的黏聚力随秸秆掺量、麦秸秆长度的增加先增大后减小,最优掺量范围为0.4%～0.6%,最优秸秆长度为15 mm;内摩擦角随着秸秆掺量的增加略有增加,但增幅很小,不同长度下无明显规律。     

土体动非线性黏弹性模型及其ABAQUS软件的实现

基于土的动应力-应变关系--Davidenkov骨架曲线,采用破坏剪应变幅上限值作为分界点,对Davidenkov骨架曲线进行了修正,即当剪应力值大于破坏剪应力值时,土体产生破坏,土体的动剪切模量采用破坏后的动剪切模量;参考Mashing法则,构造了修正后的Davidenkov骨架曲线土体加卸载对应的应力-应变滞回圈曲线。基于ABAQUS软件的操作平台,开发了土体动弹塑性本构模型的子程序。选择南京某个典型软弱场地为研究对象,首先输入余弦加速度时程曲线,然后选取一条强震加速度记录作为基岩输入地震动,对不同峰值加速度水平下该场地的地震反应进行了二维有限元非线性分析,计算结果验证了所建模型的准确性和可用性。     

Developing a 3D elastoplastic constitutive model for soils: A new approach based on characteristic stress

This paper presents a new approach for the development of an elastoplastic constitutive model to predict the strength and deformation behaviour of soils under general stress conditions. The proposed approach was based on characteristic stress, which considers the effect of the intermediate principal stress on the material strength. Referring to the Cam-clay model, the shear dilatancy equation, plastic potential function and hardening parameter for the developed model were all derived using the characteristic stress. The model predictions indicated that the established model could quantitatively reproduce the negative dilatancy behaviour, positive dilatancy behaviour, and three-dimensional strength properties of soils.     

模拟岩石应变软化变形全过程的统计损伤本构模型研究

建立可以模拟岩石应力-应变全过程的本构模型一直是岩土工程中研究的热点之一.首先,在深入探讨应变软化类岩石受力变形全过程每个阶段特征的基础上,并针对Lemaitre应变等价性理论的不足之处,基于更合理的假定建立了能够反映应变软化类岩石体积变化以及峰后出现残余强度的新型损伤模型;然后,通过引入统计损伤理论并考虑损伤阈值对岩石变形过程的影响,建立了能够模拟应变软化类岩石受力变形全过程的统计损伤本构模型,该模型还可以反映岩石的体积变化以及初始孔隙率对其变形过程的影响;最后,通过理论计算与试验结果及他人模型的对比分析,表明了该模型的合理性与可行性.     

A general approach to the modelling of contaminant transport through composite landfill liners with intact or leaking geomembranes

Finite‐element models of contaminant transport through composite landfill liners require highly refined meshes around the interface between the geomembrane and the clay layer, especially if leakage through holes in the geomembrane is considered. In addition, no general formulation for transport through leaking geomembranes can be found in the literature. The paper develops a general approach to time‐dependent contaminant migration through composite liners with intact or leaking geomembranes. Equations are derived for various combinations of system conditions including Dirichlet and Neumann boundary conditions in the waste, constant mass of contaminants in the waste, steady state or transient transport in the geomembrane, and steady state or transient seepage velocities in the mineral liner. The effect of the geomembrane on transport in the soil is converted into an equivalent boundary condition applicable at the top of the clay layer. Hence, only the media underlying the top geomembrane are explicitly represented in the numerical model, yielding a computationally efficient algorithm. The new formulation is validated in conjunction with finite‐layer, finite‐element and boundary‐element methods, by comparing its predictions to those of more conventional approaches which represent the geomembrane explicitly. The scope of the method is illustrated by modelling a landfill liner with a geomembrane leaking in five locations. Copyright © 2007 John Wiley & Sons, Ltd.     

土壤腐殖物质特征及其对有机碳长时间尺度稳定性的指示：以陕西洛川黄土剖面为例

在长时间尺度上研究土壤中腐殖物质的组成和腐殖化特征对于正确评价土壤有机质的稳定性具有重要意义。文中对洛川黄土/古土壤剖面S8以上的17个黄土和古土壤样品中的胡敏酸（HA）、富里酸（FA）和胡敏素（HM）进行定量研究,并对HA和FA的E465、E665值等进行了测定。结合该课题组对矿物组成、总有机碳（TOC）及其各组分含...