The effect of pH of water and mineralogical properties on the slake durability (degradability) of different rocks from the Lesser Himalaya, India

Slake durability is an important geotechnical parameter and is a measure of degradability of rocks due to the process of mechanical and chemical breakdown. It is closely related to the mineralogical composition and the texture of the rocks. In this paper, mineralogical examination along with slake durability tests under variable pH conditions, both in acidic and alkaline environments, on the limestone, shale and siltsone were evaluated to understand the relationship between mineralogy and the degradability of rocks. The study revealed that rocks rich in calcium carbonate and or magnesium carbonate are adversely affected in the acidic environment, whereas, the rocks rich in quartz, feldspar and muscovite are independent of the pH of the slaking fluid, which in turn, is more influenced by the texture of the constituent minerals. It has also been observed that fine grained rocks are more susceptible to degrade in comparison to the coarse grained rocks.     

一种新的岩石节理面三维粗糙度分形描述方法

研究并提出一种新的岩石节理面三维粗糙度分形描述方法。首先,基于激光扫描数据将节理表面离散成三角网,并建立与剪切方向相关的三维均方根抵抗角的计算方法。其次,运用分形数学理论,提出一种新的基于三维均方根抵抗角的节理面粗糙度分形描述方法。最后,采用新方法对天然玄武岩节理和花岗岩张拉型节理的粗糙特性进行分析。研究结果表明,提出的新方法能够较全面地反映节理面的三维几何形貌信息,并能描述节理粗糙度的各向异性特性。研究成果为进一步建立岩石节理面的三维剪切强度公式和剪切本构理论奠定了基础。     

Slaking durability and its effect on the doline formation in the gypsum

Texture and grain size is of great importance in understanding the mechanical properties of rocks. The aim of this study was to investigate textural and slaking durability characteristics, and correlate them with the gypsum types where the dolines occurred, with particular reference to the texture and crystal size. The investigation comprised two stages: field work and laboratory testing. Initially, rock samples were obtained from various representative karstified and non-karstified locations. Thereafter, mineralogical, physical and slaking durability characteristics of the gypsum samples were determined by means of laboratory testing. After the field and laboratory works, the geological, mineralogical and slaking durability characteristics of the study area gypsum were reviewed and discussed from the point of view of doline formation. Results showed that fine grain sized alabastrine gypsum tends to be karstified and leads to doline formation. This is closely related to the crystal size, texture and attributable to the slaking durability of the gypsum. Consequently, the results demonstrate that the texture, especially crystal size, and effective porosity are important parameters controlling the slake durability of the gypsum and doline formation.     

Slake durability study of shaly rock and its predictions

More than 35% of the earths crust is comprised of clay-bearing rocks, characterized by a wide variation in engineering properties and their resistance to short term weathering by wetting and drying phenomenon. The resistance to short-term weathering can be determined by slake durability index test. There are various methods to determine the slake durability indices of weak rock. The effect of acidity of water (slaking fluid) on slake durability index of shale in the laboratory is investigated. These methods are cumbersome and time consuming but they can provide valuable information on lithology, durability and weather ability of rock. Fuzzy set theory, Fuzzy logic and Artificial Neural Networks (ANN) techniques seem very well suited for typical complex geotechnical problems. In conjunction with statistics and conventional mathematical methods, a hybrid method can be developed that may prove a step forward in modeling geotechnical problems. During this investigation a model was developed and compared with two other models i.e., Neuro-fuzzy systems (combination of fuzzy and artificial neural network systems) and artificial neural network system, for the prediction of slake durability index of shaly rock to evaluate the performance of its prediction capability.     

Artificial neural networks and nonlinear regression techniques to assess the influence of slake durability cycles on the prediction of uniaxial compressive strength and modulus of elasticity for carbonate rocks

Understanding rock material characterizations and solving relevant problems are quite difficult tasks because of their complex behavior, which sometimes cannot be identified without intelligent, numerical, and analytical approaches. Because of that, some prediction techniques, like artificial neural networks (ANN) and nonlinear regression techniques, can be utilized to solve those problems. The purpose of this study is to examine the effects of the cycling integer of slake durability index test on intact rock behavior and estimate some rock properties, such as uniaxial compressive strength (UCS) and modulus of elasticity (E) from known rock index parameters using ANN and various regression techniques. Further, new performance index (PI) and degree of consistency (Cd) are introduced to examine the accuracy of generated models. For these purposes, intact rock dataset is established by performing rock tests including uniaxial compressive strength, modulus of elasticity, Schmidt hammer, effective porosity, dry unit weight, p‐wave velocity, and slake durability index tests on selected carbonate rocks. Afterward, the models are developed using ANN and nonlinear regression techniques. The concluding remark given is that four‐cycle slake durability index (I_d4) provides more accurate results to evaluate material characterization of carbonate rocks, and it is one of the reliable input variables to estimate UCS and E of carbonate rocks; introduced performance indices, both PI and Cd, may be accepted as good indicators to assess the accuracy of the complex models, and further, the ANN models have more prediction capability than the regression techniques to estimate relevant rock properties. Copyright © 2011 John Wiley & Sons, Ltd.     

The strength and fractal dimension characteristics of alum–kaolin flocs

Flocs generated by various shear forces exhibit different characteristics of size, strength and structure. These properties were investigated by employing a continuous optical monitoring and a microscope with CCD camera to directly monitor aggregation under six different shear intensities. The floc structure was characterized by the fractal dimension. The results showed that the flocculation index (FI) decreased from 1.16 at 20 rpm to 0.25 at 250 rpm and the floc size decreased from 550 μm to 150 μm, meantime, the FI value showed a good correlation with floc size. In order to determine the floc strength, two methods were used. One was the strength factor, ranging from 18.3% to 62.5%, calculated from FI curve, and the other was a theoretical value between 0.005 N/m² and 0.240 N/m², estimated by calculation. The floc strength increased with the G value in both cases. Furthermore, the fractal dimension increased with G and its value was between 1.30 and 1.63. The relation between fractal dimension and strength was also obtained.     

岩石破裂过程中的声发射b值及分形特征研究

应用声发射及其定位技术,通过单轴受压岩石破坏声发射试验,对岩石破裂过程中的声发射b值和空间分布分形维值随不同应力水平的变化趋势进行了研究。研究结果表明：声发射分形维值D和b值反映了岩石破坏过程中微裂纹的初始和扩展;在小尺度微裂纹所占比例较高的加载初期,分形维值和b值在较高的水平波动变化,部分岩石试件分形维值和b值呈现升高现象;随着载荷的增加,岩石内部微裂纹的空间分布由无序向有序转变,大尺度裂纹所占比例增加,声发射定位事件出现群集现象,分形维值和b值开始较快速下降并在岩石失稳破坏时达到最低值。在岩石破坏过程中,声发射分形维值和b值的变化趋势相近。由于实际应用时,分形维值和b值的最小值（临界点）难以确定,故可将2个参数相结合,以分形维值D和b值较快速下降作为前兆特征,以提高现场岩体稳定性监测的准确性。     

基于岩体结构面分布分形维的岩体质量评价

尽管岩体结构面具有空间上的不规则性和结构网络上的复杂性,但由于它又具有自相似的特征,可以运用分形理论来对其进行研究。运用盒计维数法对某矿山巷道围岩体结构面分布的分维数进行计算,验证了岩体结构面分布的分形特征。通过对岩体结构面分布分形维值分布规律的分析发现,分形维数越大、结构面分布越密集,结构面迹线越长,岩体质量越差,表明可将岩体结构面分布的分形维作为岩体质量评价的指标。将计算所得的岩体结构面分布的分维数与按工程岩体分级标准对相应岩体分级所得的岩体质量等级进行对比,提出了一个以岩体结构面分布的分形维作为分级指标的岩体质量评价方案。     

Geomorphometry and fractal dimension of a riverine badland in Maharashtra

One of the most serious limitations in studying the surface morphometry of a badland landscape is the nonavailability of a very fine resolution data which is essential for such types of studies. Local relief of most of the badlands in India and also from other parts of the world exhibit limited relief amplitude, often within a few meters. The paper reports a case study carried out in a riverine badland formed along the Western Deccan Trap Region. An attempt has been made in the present paper to extract the morphometric variables of the landscape from the DEMs derived from a high resolution field generated data, because the accuracy of the DEM derived values are dependent on the pixel resolution of the DEM from which they are generated. The size of the pixel resolution should be fixed differently for different landscapes depending on the landscape process in the area. The local relief of the area is around 10 m and for such types of landscapes the topographical maps and also the web-available DEMs are of very coarse resolutions which are not suitable for the analysis. Therefore two well defined tributary catchments were chosen from the area under investigation and theodolite surveys were carried out, contours were generated with 10 cm interval, DEMs were derived by using Arc GIS software. SRTM (Shuttle Radar Topography Mission) 90 m resolution data were utilized to generate DEM for the whole basin. Hypsometric and the drainage basin parameters were extracted from these data by using the same software. Fractal dimension of the whole basin and the sample basins were also obtained for the same data. The morphometric data generated were used to understand the geomorphic processes operating in the area.     

Factors affecting the durability of selected weak and clay-bearing rocks from Turkey, with particular emphasis on the influence of the number of drying and wetting cycles

Weathering can induce a rapid change of rock material from initial rock-like properties to soil-like properties. The resistance of a rock to short-term weathering is described through a durability parameter called the slake durability index. As durability is an important engineering parameter, particularly for weak and clay-bearing rocks, it was assessed by a number of tests. The main purpose of this study is to assess the influence of the number of drying and wetting cycles and controls of mineralogical composition and strength on durability. For this purpose, 141 samples of different types of weak and clay-bearing rocks were selected from different parts of Turkey, and relationships between the above-mentioned rock characteristics were statistically investigated. The samples were subjected to multiple-cycle slake durability testing, X-ray diffraction (XRD) analysis and uniaxial compression testing. In addition, to assess the influence of mineralogical composition on durability, the mineral contents of the original material and the material passing from the drum of the slake durability apparatus after each cycle were also determined by XRD. The results indicate that the type and amount of clay minerals are the main factors influencing the variations of the slake durability index in all samples. The durability of the clay-bearing rocks studied correlates best with the amount of expandable clay minerals. A strong relationship between the uniaxial compressive strength and the fourth-cycle slake durability index is found only for the marls among the rock types studied. Assessment of gradation results of the spoil pile materials consisting of clay-bearing rocks also reveals that the increase in percentage of fines in old piles is indicative of material degradation, as is evident by multiple-cycle slaking. It is emphasized that two-cycle conventional slake durability testing did not appear to offer an acceptable indication of the durability of weak and clay-bearing rocks when compared with multiple-cyclic wetting and drying. Comments on the performance of the test are made that aim to make the testing process and interpretation of the results more reliable.     

The fractal dimension of pores in sedimentary rocks and its influence on permeability

Perimeter-area power-law relationship of pores in five sedimentary rocks are estimated from scanning electron micrographs of thin sections. These relationships for the pores of four sandstones were found to lie between 1.43 and 1.49, while that of an Indiana limestone was found to be 1.67. We show how the perimeter-area power-law relationship of pores, along with a pore-size distribution, can be used to estimate the hydraulic permeability. A discussion is given of how the fractal dimension of the pore perimeter derived by Mandelbrot for islands whose boundaries are fractal: P = ε^DA^D/2, where ε is some constant that depends on the length of the measuring grid size and D is the fractal dimension of the pore perimeter, influences permeability.     

花岗岩电镜扫描图像二值化阈值对分形维数影响的研究

电镜扫描应用于岩土工程研究,能观察到岩石的细观结构,从另一个视角揭示岩石力学机理。分形维数是对岩石表面不规则、非线性裂纹裂隙的定量描述,是一个重要的参数指标。本文首先通过花岗岩电镜扫描实验,获得了花岗岩细观图像;其次研究不同二值化阈值下的图像和分形维数,结果显示分形维数随二值化阈值增大而减小;最后,对比迭代法、双峰法和Otsu法三种求最佳二值化阈值方法,表明Otsu法简单易行,得到的图像能反映岩石表面细节,求出的分形维数具有参考对比价值。因此将Otsu法图像二值化阈值得到的分形维数作为对比参考的标准,对岩石细观研究具有重要的参考价值。     

土石混合料剪切面分形特征试验研究

土石混合料因具有良好的工程特性而被广泛应用于道路、堤坝等工程，填筑体受力后往往沿薄弱面发生剪切破￡混合料的抗剪强度成为稳定和变形分析的重要力学指标。由于土石混合料物质组成的复杂性、结构分布的不规律性及采柠困难性，且受检测仪器的限制，确定其强度指标较为困难。应用改进的直剪试验仪进行了不同类别、不同最大粒径土石福料的室内大型直剪试验，在获得强度指标同时，再现剪切面的实际情况，量测剪切面的起伏特征。根据分形几何学原理，切面具有良好的分形特征，应用三角形棱柱表面积覆盖法编程计算了剪切面的分形维数。初步建立了剪切面分形维数与福料杭萌强度之间的关系，用来快速预测土石混合料的强度指标。     

Fractal dimension of profiles and surfaces using fuzzy morphological coverings

In this paper, we propose a new method, based on fuzzy morphology coverings, to estimate the fractal dimension of profiles and surfaces. This method is geometrically intuitive and simple to implement. Algorithmically, the method fits a covering to the frames or blocks of the profile or surface using fuzzy morphology. Varying the dimension of the frame or block, estimates of the length or area covered are then used to find the fractal dimension. Validation of the proposed method is performed by comparing its results with known fractal dimensions of mathematical profiles. The method is used to obtain the fractal dimension of rock profiles and surfaces.     

岩石结构面粗糙度系数尺寸效应的推拉试验研究

粗糙度系数是结构面抗剪强度的主要影响因素,然而由于结构面表面形态的复杂性,粗糙度系数尺寸效应研究并未获得较大进展。总结了结构面粗糙度系数的3种获取手段：标准剖面对比法、理论公式法、试验反分析法。在此基础上分析了3种方法在研究粗糙度系数尺寸效应方面存在的问题和困难。为了研究结构面粗糙度系数与试样尺寸的相关度,对中砂、硅粉、水泥、非引气型萘系减水剂等原材料的配比进行了研究,获得了与天然钙质板岩物理力学特性相类似的岩石模型材料,然后采用研发的结构面制作模具及其制备工艺制作了8组共176对具有不同尺寸和表面起伏粗糙程度的结构面,并利用改进的高精度岩石结构面推拉仪对结构面粗糙度系数进行了推拉试验研究和数据统计分析,结果表明：模型结构面粗糙度系数的统计均值随试样尺寸的增加而降低,但特定结构面粗糙度系数的尺寸效应规律需要根据结构面的具体表面形貌进行测试;Barton理论公式计算的结构面粗糙度系数尺寸效应变化规律与推拉试验测试规律总体上一致,但试验值与理论值有差异,且结构面试样尺寸越小,二者的差异就越大;具有特定表面形貌的模型结构面粗糙度系数也有差异,工程大尺寸岩体结构面粗糙度系数需要根据表面形貌和分布特征进行综合判定。     

基于岩体结构面统计与分维数的岩体质量评价及其在矿山工程中的应用

以三山岛金矿-510中段和-555中段为例,基于结构面实测数据,利用Matlab对结构面特征进行统计模型,进而实现了岩体裂隙网络Monte-Carlo模拟。然后结合分形理论确定了岩体质量的分维值。研究表明,-510中段和-555中段F3以北的岩体稳定性要好于F3以南的岩体稳定性,从定性和定量的角度对岩体质量进行了分析,为矿山的安全生产提供了一定的依据。     

基于饱和指数模型的坝基帷幕体防渗效果及耐久性研究

帷幕体的修建是为了对坝基进行加固和防渗,但在蓄水条件下,坝基帷幕体遭受长期的高压渗流、溶蚀等作用,坝基帷幕防渗作用衰减以致失效,从而引起坝基渗流量增加和扬压力增高。依据地球化学热力学的基本理论,通过分析坝基地下水微观动态,定量化解析幕后地下水溶液与某种矿物之间的反应状态,采用了基于化学热力学模型的FORTRAN程序,从一个侧面来反映坝基帷幕体防渗效果及其耐久性。结合某工程实例,建立2001－2010年的时间序列模型,计算出的方解石饱和指数由2.03变为0.26,揭示出某坝10坝段处坝基帷幕体的防渗性能及其耐久性发生了衰减,且具有阶段性变化的特点,2001－2004年间与2006－2008年间坝基地下水的微观动态处于相对稳定的时期（缓变）;2005年间与2009－2010年间处于突变时期（陡变）。揭示出该坝段坝基帷幕体的防渗性能出现了局部的衰减,其结果与地下水宏观动态反映出的规律较一致,证明该方法在一个侧面能够反映出帷幕体的防渗性能和耐久性的变化特征。