The “slip law” of the free surface

A “slip law” connects the excess velocity or “slip” of a wind-blown water surface, relative to the motion in the middle of the mixed layer, to the wind stress, the wind-wave field, and buoyancy flux. An inner layer-outer layer model of the turbulent shear flow in the mixed layer is appropriate, as for a turbulent boundary layer or Ekman layer over a solid surface, allowing, however, for turbulent kinetic energy transfer from the air-side via breaking waves, and for Stokes drift. Asymptotic matching of the velocity distributions in inner and outer portions of the mixed layer yields a slip law of logarithmic form, akin to the drag law of a turbulent boundary layer. The dominant independent variable is the ratio of water-side roughness length to mixed layer depth or turbulent Ekman depth. Convection due to surface cooling is also an important influence, reducing surface slip. Water-side roughness length is a wind-wave property, varying with wind speed similarly to air-side roughness. Slip velocity is typically 20 times water-side friction velocity or 3% of wind speed, varying within a range of about 2 to 4.5%. A linearized model of turbulent kinetic energy distribution shows much higher values near the surface than in a wall layer. Nondimensional dissipation peaks at a value of about eight, a short distance below the surface.     

Modification of the damping function in the k–ε model to analyse oscillatory boundary layers

A simple relationship has been developed between the wall coordinate y⁺ and Kolmogorov's length scale using direct numerical simulation (DNS) data for a steady boundary layer. This relationship is then utilized to modify two popular versions of low Reynolds number k–ε model. The modified models are used to analyse a transitional oscillatory boundary layer. A detailed comparison has been made by virtue of velocity profile, turbulent kinetic energy, Reynolds stress and wall shear stress with the available DNS data. It is observed that the low Reynolds number models used in the present study can predict the boundary layer properties in an excellent manner.     

Effects of Stokes production on summer ocean shelf dynamics

A two-dimensional numerical model,which is configured on the basis of Princeton ocean model（POM）,is used to study the effect of Stokes production（SP） of the turbulent kinetic energy on a density profile and Ekman transport in an idealized shelf region in summer.The energy input from SP is parameterized and included into the Mellor-Yamada turbulence closure submodel.Results reveal that the intensity of wind-driven upwelling fronts near the sea surface is weakened by the SP-associated turbulent kinetic energy input.The vertical eddy viscosity coefficient in the surface boundary layer is enhanced greatly owing to the impact of SP,which decreases the alongshore velocity and changes the distribution of upwelling.In addition,the SP-induced mixing easily suppresses the strong stratification and significantly increases the depth of the upper mixed layer（ML） under strong winds.     

Flow under standing waves: Part 1. Shear stress distribution,energy flux and steady streaming

The conditions for energy flux, momentum flux and the resulting streaming velocity are analysed for standing waves formed in front of a fully reflecting wall. The exchange of energy between the outer wave motion and the near bed oscillatory boundary layer is considered, determining the horizontal energy flux inside and outside the boundary layer. The momentum balance, the mean shear stress and the resulting time averaged streaming velocities are determined. For a laminar bed boundary layer the analysis of the wave drift gives results similar to the original work of Longuet–Higgins from 1953. The work is extended to turbulent bed boundary layers by application of a numerical model. The similarities and differences between laminar and turbulent flow conditions are discussed, and quantitative results for the magnitude of the mean shear stress and drift velocity are presented. Full two-dimensional simulations of standing waves have also been made by application of a general purpose Navier–Stokes solver. The results agree well with those obtained by the boundary layer analysis. Wave reflection from a plane sloping wall is also investigated by using the same numerical model and by physical laboratory experiments. The phase shift of the reflected wave train is compared with theoretical and empirical models.     

Effect of surface wave breaking on the surface boundary layer of temperature in the Yellow Sea in summer

Near-surface enhancement of turbulent mixing and vertical mixing coefficient for temperature owing to the effect of surface wave breaking is investigated using a two-dimensional (2-D) ocean circulation model with a tidal boundary condition in an idealized shelf sea. On the basis of the 2-D simulation, the effect of surface wave breaking on surface boundary layer deepening in the Yellow Sea in summer is studied utilizing a 3-D ocean circulation model. A well-mixed temperature surface layer in the Yellow Sea can be successfully reconstructed when the effect of surface wave breaking is considered. The diagnostic analysis of the turbulent kinetic energy equation shows that turbulent mixing is enhanced greatly in the Yellow Sea in summer by surface wave breaking. In addition, the diagnostic analysis of momentum budget and temperature budget also show that surface wave breaking has an evident contribution to the turbulent mixing in the surface boundary layer. We therefore conclude that surface wave breaking is an important factor in determining the depth of the surface boundary layer of temperature in the Yellow Sea in summer.     

Reynolds number variation in oscillatory boundary layers: Part I. Purely oscillatory motion

A numerical model based upon a low Reynolds number turbulence closure is proposed to study Reynolds number variation in reciprocating oscillatory boundary layers. The model is used to compute the boundary layer for flow regimes ranging from smooth laminar to rough turbulent. Criteria for fully developed turbulence are derived for walls of the smooth and rough types. In particular, a new criterion to identify the rough turbulent regime is determined based on the time-averaged turbulence intensity. The reliability of the present model is assessed through comparisons with detailed experimental data collected by other investigators. The model globally improves upon standard high Reynolds number closures. Variation through the wave cycle of the main flow variables (ensemble-averaged velocity, shear stress, turbulent kinetic energy) is remarkably well-predicted for smooth walls. Predictions are satisfactory for rough walls as well. Yet, the turbulence level in the rough turbulent regime is overpredicted in the vicinity of the bed.     

Bottom friction and its effects on periodic long wave propagation

A new set of Boussinesq-type equations describing the free surface evolution and the corresponding depth-integrated horizontal velocity is derived with the bottom boundary layer effects included. Inside the boundary layer the eddy viscosity gradient model is employed to characterize Reynolds stresses and the eddy viscosity is further approximated as a linear function of the distance measured from the seafloor. Boundary-layer velocities are coupled with the irrotational velocity in the core region through boundary conditions. The leading order boundary layer effects on wave propagation appear in the depth-integrated continuity equation to account for the velocity deficit inside the boundary layer. This formulation is different from the conventional approach in which a bottom stress term is inserted in the momentum equation. An iterative scheme is developed to solve the new model equations for the free surface elevation, depth-integrated velocity, the bottom stress, the boundary layer thickness and the magnitude of the turbulent eddy viscosity. A numerical example for the evolution of periodic waves propagating in one-dimensional channel is discussed to illustrate the numerical procedure and physics involved. The differences between the conventional approach and the present formulation are discussed in terms of the bottom frictional stress and the free surface profiles.     

Asymptotic behaviour of a turbulent mixing path near a wave layer

The paper reports on a class of models for a turbulent boundary layer which are based on the turbulent energy balance equation and closure and use hypothesis of the type of Karman relations for turbulent mixing paths or complementary transport equations. It is shown that in the absence of a velocity shear near the kinetic turbulent energy flux all the models are encompassed by a unique hypothesis and satisfy with depth a linear dependence of the mixing path.Translated by Vladimir A. Puchkin.     

Modeling a neutrally stratified turbulent air flow over a horizontal rough surface

The neutrally stratified boundary layer over a smooth rough surface is consider. The turbulent flow is simulated using a finite-difference eddy-resolving model of the atmospheric boundary layer (ABL). The model includes different turbulence closure schemes and numerical approximations for advection components of the momentum balance equation. We investigate the quality of reproduction of spectral characteristics of the turbulent flow and the model’s capabilities to reproduce the observed profile of mean wind velocity near the rough surface. It is shown that the best result is obtained by coupling a numerical scheme of higher order of accuracy with a mixed closure scheme based on an adaptive estimation of the mixing length for subgrid-scale fluctuations. Here, we are able to reproduce the asymptotics of the fluctuation spectrum of the longitudinal component of wind velocity near the surface and within the boundary layer as well as the logarithmic profile of mean velocity near the surface.     

湍流局地平衡假设的新推论--齐次湍流动能输运方程封闭模型与应用(Ⅱ)

在湍流局地平衡假设下 ,建立了齐次湍能输运方程封闭模型 (HKE) ,并在平板边界层的两种经典流动中加以检验 ,给出 HKE封闭下的流速、湍流动能和湍流混合系数剖面的形式解。结果表明 ,HKE可以避免在流速剪切为零时的无湍流混合问题 ,其解与 L aufer湍流实验吻合 ,因而HKE模型比混合长理论有更合理的内涵。文中还给出 HKE封闭的浅海动力学模型 ,以湍应力和水位梯度力的平衡为运动的基本受力平衡 ,进行了模型的量阶分析和运动分析 :当阻尼频率和运动频率同量阶时 ,惯性运动不可忽略 ;在潮振荡占优的浅海中 ,对流非线性相对于惯性运动为小量 ;当阻尼频率足够大时 ,科氏力项相对于湍应力也可能为小量。     

A new approach to oscillatory rough turbulent boundary layers

Velocity measurements have been performed in an oscillatory turbulent boundary layer over a rough wall, using a large oscillating water tunnel. These together with measurements by Kalkanis (1964) over an oscillating wall indicate the existence of universal wall and defect laws for velocity. A logarithmic overlap layer is predicted and observed as in a steady turbulent boundary layer, and this results in a new relationship between friction factor and relative boundary layer thickness. The phase lead of the defect velocity relative to the wall ditto seems to follow a universal law over the whole defect layer. A method is suggested for the calculation of the phase lead of wall shear stress over velocity in the free stream for large amplitude to roughness ratios. Apart from the inner layer, it is in principle possible to construct the velocity profiles in a turbulent oscillatory boundary layer at a rough wall, using the findings of this report. A review of experimental and theoretical investigations of the stability of the oscillatory boundary layer is also given.     

珠江河口底边界层湍流特征量研究

通过高频流速仪ADV和脉冲相干声学多普勒剖面仪PC-ADP对珠江河口崖门底边界层进行了三个测次潮内(25 h)顶点连续观测,利用观测数据计算分析了潮流底边界层内的湍流特征量及其时空变化.结果表明:1)对于半日潮流占优的河口,各湍流特征量均具有明显的四分之一周日的变化规律;2)湍流强度、床底应力和摩阻流速在潮内的平均值以位于河口湾的测点所测值最大,依次向上游递减,而湍动能耗散率则沿河口湾至上游逐渐增大;3)三个测次边界层内涡动粘滞系数的平均值分别为2.42×10 -3 m 2/s、2.20×10 -4m 2/s和6.16×10 -4 m 2/s,拖曳系数的均值为7.89×10 -3、1.63×10 -3和1.99×10 -2,两者潮内的变化均非常显著,相差可达一到两个数量级;4)在充分混合的潮流底边界层内,湍动能生成与耗散基本处于局部平衡状态,三个测次湍动能耗散率均值在8.89×10 -5 W/kg～7.43×10 -6 W/kg之间.     

Effect of bed roughness on turbulent boundary layer and net sediment transport under asymmetric waves

This paper presents an investigation of the roughness effects in the turbulent boundary layer for asymmetric waves by using the baseline (BSL) k–ω model. This model is validated by a set of the experimental data with different wave non-linearity index, N_i (namely, N_i = 0.67, N_i = 0.60 and N_i = 0.58). It is further used to simulate asymmetric wave velocity flows with several values of the roughness parameter (a_m/k_s) which increase gradually, namely from a_m/k_s = 35 to a_m/k_s = 963. The effect of the roughness tends to increase the turbulent kinetic energy and to decrease the mean velocity distribution in the inner boundary layer, whereas in the outer boundary layer, the roughness alters the turbulent kinetic energy and the mean velocity distribution is relatively unaffected. A new simple calculation method of bottom shear stress based on incorporating velocity and acceleration terms is proposed and applied into the calculation of the rate of bed-load transport induced by asymmetric waves. And further, the effect of bed roughness on the bottom shear stress and bed-load sediment transport under asymmetric waves is examined with the turbulent model, the newly proposed method, and the existing calculation method. It is found that the higher roughness elements increase the magnitude of bottom shear stress along a wave cycle and consequently, the potential net sediment transport rate. Moreover, the wave non-linearity also shows a big impact on the bottom shear stress and the net sediment transport.     

海浪破碎对海洋上混合层中湍能量收支的影响

海浪破碎产生一向下输入的湍动能通量,在近海表处形成一湍流生成明显增加的次层,加强了海洋上混合层中的湍流垂向混合。为了研究海浪破碎对混合层中湍能量收支的影响,文中分析了海浪破碎对海洋上混合层中湍流生成的影响机制,采用垂向一维湍封闭混合模式,通过改变湍动能方程的上边界条件,引入了海浪破碎产生的湍动能通量,并分别对不同风速下海浪破碎的影响进行了数值研究,分析了混合层中湍能量收支的变化。当考虑海浪破碎影响时,近海表次层中的垂直扩散项和耗散项都有显著的增加,该次层中被耗散的湍动能占整个混合层中耗散的总的湍能量的92.0%,比无海浪破碎影响的结果增加了近1倍;由于平均流场切变减小,混合层中的湍流剪切生成减小了3.5%,形成一种存在于湍动能的耗散和垂直扩散之间的局部平衡关系。在该次层以下,局部平衡关系与壁层定律的结论一致,即湍动能的剪切生成与耗散相平衡。研究结果表明,海浪破碎在海表产生的湍动能通量影响了海洋上混合层中的各项湍能量收支间的局部平衡关系。     

A Lagrangian model for boundary layer growth and bed shear stress in the swash zone

A new model for the boundary layer development and associated skin friction coefficients and shear stress within the swash zone is presented. The model is developed within a Lagrangian reference frame, following fluid trajectories, and can be applied to both laminar flow and smooth turbulent flow. The model is based on the momentum integral approach for steady, flat-plate boundary layers, with appropriate modifications to account for the unsteady flow regime and flow history. The model results are consistent with previous measurements of bed shear stress and skin friction coefficients within the swash zone. These indicate strong temporal and spatial variation throughout the swash cycle, and a clear distinction between the uprush and backwash phase. This variation has been previously attributed the unsteady flow regime and flow history effects, both of which are accounted for in the new model. Fluid particle trajectories and velocity are computed using the non-linear shallow water wave equations and the boundary layer growth across the entire swash zone is estimated. Predictions of the bed shear stress and skin friction coefficients agree reasonably well with direct bed shear stress measurements reported by Barnes et al. (Barnes, M.P., O’Donaghue, T., Alsina, J.M., Baldock, T.E., 2009. Direct bed shear stress measurements in bore-driven swash. Coastal Engineering 56 (8), 853–867) and, for a given flow velocity, give stresses which are consistent with the bias toward uprush sediment transport which has consistently been observed in measurements. The data and modelling suggest that the backwash boundary layer is initially laminar, which results in the late development of significant bed shear during the backwash, with a transition to a turbulent boundary layer later in the backwash. A new conceptual model for the boundary layer structure at the leading edge of the swash is proposed, which accounts for both the no-slip condition at the bed and the moving wet–dry interface. However, further development of the Lagrangian Boundary Layer Model is required in order to include bore-generated turbulence and to account for variable roughness and mobile beds.     

Boundary layer approach in the modeling of breaking solitary wave runup

The boundary layer is very important in the relation between wave motion and bed stress, such as sediment transport. It is a known fact that bed stress behavior is highly influenced by the boundary layer beneath the waves. Specifically, the boundary layer underneath wave runup is difficult to assess and thus, it has not yet been widely discussed, although its importance is significant. In this study, the shallow water equation (SWE) prediction of wave motion is improved by being coupled with the k–ω model, as opposed to the conventional empirical method, to approximate bed stress. Subsequently, the First Order Center Scheme and Monotonic Upstream Scheme of Conservation Laws (FORCE MUSCL), which is a finite volume shock-capturing scheme, is applied to extend the SWE range for breaking wave simulation. The proposed simultaneous coupling method (SCM) assumes the depth-averaged velocity from the SWE is equivalent to free stream velocity. In turn, free stream velocity is used to calculate a pressure gradient, which is then used by the k–ω model to approximate bed stress. Finally, this approximation is applied to the momentum equation in the SWE. Two experimental cases will be used to verify the SCM by comparing runup height, surface fluctuation, bed stress, and turbulent intensity values. The SCM shows good comparison to experimental data for all before-mentioned parameters. Further analysis shows that the wave Reynolds number increases as the wave propagates and that the turbulence behavior in the boundary layer gradually changes, such as the increase of turbulent intensity.     

Laboratory study of wave and turbulence velocities in a broad-banded irregular wave surf zone

The characteristics of wave and turbulence velocities created by a broad-banded irregular wave train breaking on a 1:35 slope were studied in a laboratory wave flume. Water particle velocities were measured simultaneously with wave elevations at three cross-shore locations inside the surf zone. The measured data were separated into low-frequency and high-frequency time series using a Fourier filter. The measured velocities were further separated into organized wave-induced velocities and turbulent velocity fluctuations by ensemble averaging. The broad-banded irregular waves created a wide surf zone that was dominated by spilling type breakers. A wave-by-wave analysis was carried out to obtain the probability distributions of individual wave heights, wave periods, peak wave velocities, and wave-averaged turbulent kinetic energies and Reynolds stresses. The results showed that there was a consistent increase in the kurtosis of the vertical velocity distribution from the surface to the bottom. The abnormally large downward velocities were produced by plunging breakers that occurred from time to time. It was found that the mean of the highest one-third wave-averaged turbulent kinetic energy values in the irregular waves was about the same as the time-averaged turbulent kinetic energy in a regular wave with similar deep-water wave height to wavelength ratio. It was also found that the correlation coefficient of the Reynolds stress varied strongly with turbulence intensity. Good correlation between u′ and w′ was obtained when the turbulence intensity was high; the correlation coefficient was about 0.3–0.5. The Reynolds stress correlation coefficient decreased over a wave cycle, and with distance from the water surface. Under the irregular breaking waves, turbulent kinetic energy was transported downward and landward by turbulent velocity fluctuations and wave velocities, and upward and seaward by the undertow. The undertow in the irregular waves was similar in vertical structure but lower in magnitude than in regular waves, and the horizontal velocity profiles under the low-frequency waves were approximately uniform.     

Large-scale turbulence under a solitary wave

The structure of large-scale turbulence under a broken solitary wave on a 1 in 50 plane slope was studied. Three-component velocity measurements were taken at different heights above a smooth bed in the middle surf zone using an acoustic Doppler velocimeter. The measured data showed that turbulent velocity components were well correlated in the middle part of the water column. The velocity correlations could be produced by an oblique vortex similar to the obliquely descending eddy observed previously by other investigators. The vertical distributions of the relative values of the components of the Reynolds stress tensor showed that the structure of turbulence evolved continuously between the free surface and the bottom. The evolution was related to transition from two-dimensional to three-dimensional flow structures and the effect of the solid bottom on flow structures. Time histories of measured turbulent kinetic energy and turbulence stresses showed episodic turbulent events near the free surface but more sporadic turbulence in the lower layer. Large or intense turbulent events were found to have short duration and time lag relative to the wave crest point. These events also maintained good correlations between the turbulence velocity components close to the bottom.Instantaneous turbulent velocity fields were measured near the bottom at the same cross-shore location by using a stereoscopic particle image velocimetry system. These measurements showed that the near-bed flow field was characterized by large-scale, coherent flow structures that were the sources of most of the turbulent kinetic energy and turbulence stresses. The types of organized flow structures observed included vortices and downbursts of turbulence descending directly from above, lateral spreading of turbulent fluid along the bed, and formation of vortices in shear layers between fluid streams. A common feature of the organized flow structures near the bed was the large turbulence velocities in the longitudinal and transverse directions, which reflected the influence of a solid bottom on the breaking-wave-generated turbulence arriving at the bed.     

Turbulence-induced steady streaming in an oscillating boundary layer: On the reliability of turbulence closure models

The accuracy of several closure models of the Reynolds-Averaged Navier–Stokes Equations in predicting the characteristics of an oscillating turbulent wall boundary layer is analyzed. The analysis involves four low Reynolds number k − ε models and a k − ω model and it is carried out by comparing the model results both with experimental data and with data obtained by a Direct Numerical Simulation (DNS) of the Navier–Stokes equations. The boundary layer is generated by a spatially constant time-oscillating pressure gradient given by the sum of two harmonic components characterized by angular frequencies Ω^∗ and 2Ω^∗ respectively, which generates a steady streaming because of the asymmetry of turbulence intensity during the cycle. Thus the results are relevant to the boundary layer at the bottom of nonlinear sea waves. The attention is therefore focused on the accuracy of the models in reproducing the period averaged profiles of the hydrodynamic characteristics of the steady streaming. The instantaneous quantities, such as time development of the wall shear stress, profiles of the streamwise velocity, Reynolds stresses and turbulent kinetic energy are also considered and analyzed. The results shows that a model can be judged better or worse than other models depending on the specific flow characteristic under investigation. However, an approach has been adopted which allowed to rank the models according to their accuracy in predicting the values of the hydrodynamic quantities involved in the present study.