The effect of spacecraft radiation sources on electron moments from the Cassini CAPS electron spectrometer

Data from the Cassini plasma spectrometer (CAPS) electron spectrometer (ELS) have been found to be contaminated with an energy-independent background count rate which has been associated with radiation sources on Cassini. In this paper we describe this background radiation and quantitatively assess its impact on numerically integrated electron moments. The general properties of such a background and its effects on numerical moments are derived. The properties of the ELS background are described and a model for the background presented. A model to generate synthetic ELS spectra is presented and used to evaluate the density and temperature of pure noise and then extended to include ambient distributions. It is shown that the presence of noise produces a saturation of the electron density and temperature at quasi-constant values when the instrument is at background, but that these noise level moments are dependent on the floating spacecraft potential and the orientation of the ELS instrument with respect to the spacecraft. When the ambient distribution has a poor signal-to-noise ratio (SNR) the noise determines the density and temperature; however, as the SNR increases (increasing primarily with density) the density and temperature tend to those of the ambient distribution. It is also shown that these noise effects produce highly artificial density-temperature inverse correlations. A method to subtract this noise is presented and shown to correct for the presence of the noise. Simulated error estimates for the density and temperature are also presented. The analysis described in this paper not only applies to weak background noise, but also to more significant penetrating backgrounds such as those in radiation belt regions of planetary magnetospheres.     

Investigation of energetic proton penetration in Titan's atmosphere using the Cassini INCA instrument

Saturn's largest moon, Titan, provides an interesting opportunity to study how dense atmospheres interact with the surrounding plasma environment. Without an intrinsic magnetic field, this satellite's nitrogen-rich atmosphere is relatively unprotected from plasma interactions. Therefore, the energy-deposition rate is important for understanding chemistry and dynamics in Titan's atmosphere. Since the plasma environment can vary significantly we focus here on the T18 Titan encounter using in-situ data from instruments on board the Cassini spacecraft. These instruments cannot provide in-situ information below the spacecraft closest approach altitude (∼>960 km) so we use the Cassini magnetospheric imaging instrument (MIMI) ion-neutral camera (INCA) to remotely image energetic hydrogen particle fluxes (20-80 keV) at altitudes below Titan closest approach. We also use the MIMI low-energy magnetosphere measurements system (LEMMS) to measure the incident ion fluxes as the spacecraft approaches Titan and combine these data sets with an atmospheric model to first reproduce INCA images. We then use this model to calculate the energy-deposition profiles for the observed incident proton flux. Our model is able to reproduce the INCA observations and give the energy density deposited vs. altitude in Titan's atmosphere; however, we find that the incident fluxes and energy-deposition profiles vary significantly during the encounter.     

The calibration of the Cassini-Huygens CAPS Electron Spectrometer

We present the two-stage method used to calibrate the electron spectrometer (ELS), part of the plasma spectrometer (CAPS) on board the Cassini spacecraft currently in orbit around Saturn. The CAPS-ELS is a top-hat electrostatic analyser designed to measure electron fluxes between 0.5 eV and 26 keV. The on-ground calibration method described here includes the production of photoelectrons, which are energised and passed into the CAPS-ELS in a purpose designed calibration facility. Knowledge of the intensity of these incident electrons and the subsequent instrument output provides an on-ground calibrated geometric factor. Comparative studies of physical quantities such as plasma density and electron differential flux calculated using on-ground calibration factor with the quantities deduced from the wave experiment and high energy electron detector provide in-flight calibration. The results of this are presented together with a comparison of the experimentally calibrated values with simulated calibration values.     

Energy deposition and primary chemical products in Titan’s upper atmosphere

Cassini results indicate that solar photons dominate energy deposition in Titan’s upper atmosphere. These dissociate and ionize nitrogen and methane and drive the subsequent complex organic chemistry. The improved constraints on the atmospheric composition from Cassini measurements demand greater precision in the photochemical modeling. Therefore, in order to quantify the role of solar radiation in the primary chemical production, we have performed detailed calculations for the energy deposition of photons and photoelectrons in the atmosphere of Titan and we validate our results with the Cassini measurements for the electron fluxes and the EUV/FUV emissions. We use high-resolution cross sections for the neutral photodissociation of N₂, which we present here, and show that they provide a different picture of energy deposition compared to results based on low-resolution cross sections. Furthermore, we introduce a simple model for the energy degradation of photoelectrons based on the local deposition approximation and show that our results are in agreement with detailed calculations including transport, in the altitude region below 1200 km, where the effects of transport are negligible. Our calculated, daytime, electron fluxes are in good agreement with the measured fluxes by the Cassini Plasma Spectrometer (CAPS), and the same holds for the measured FUV emissions by the Ultraviolet Imaging Spectrometer (UVIS). Finally, we present the vertical production profiles of radicals and ions originating from the interaction of photons and electrons with the main components of Titan’s atmosphere, along with the column integrated production rates at different solar zenith angles. These can be used as basis for any further photochemical calculations.     

Evaluating Uncertainties in Coronal Electron Temperature and Radial Speed Measurements Using a Simulation of the Bastille Day Eruption

Obtaining reliable measurements of plasma parameters in the Sun’s corona remains an important challenge for solar physics. We previously presented a method for producing maps of electron temperature and speed of the solar corona using K-corona brightness measurements made through four color filters in visible light, which were tested for their accuracies using models of a structured, yet steady corona. In this article we test the same technique using a coronal model of the Bastille Day (14 July 2000) coronal mass ejection, which also contains quiet areas and streamers. We use the coronal electron density, temperature, and flow speed contained in the model to determine two K-coronal brightness ratios at (410.3, 390.0 nm) and (423.3, 398.7 nm) along more than 4000 lines of sight. Now assuming that for real observations, the only information we have for each line of sight are these two K-coronal brightness ratios, we use a spherically symmetric model of the corona that contains no structures to interpret these two ratios for electron temperature and speed. We then compare the interpreted (or measured) values for each line of sight with the true values from the model at the plane of the sky for that same line of sight to determine the magnitude of the errors. We show that the measured values closely match the true values in quiet areas. However, in locations of coronal structures, the measured values are predictably underestimated or overestimated compared to the true values, but can nevertheless be used to determine the positions of the structures with respect to the plane of the sky, in front or behind. Based on our results, we propose that future white-light coronagraphs be equipped to image the corona using four color filters in order to routinely create coronal maps of electron density, temperature, and flow speed.     

Saturn Satellites as Seen by Cassini Mission

In this paper we will summarize some of the most important results of the Cassini mission concerning the satellites of Saturn. The Cassini Mission was launched in October 1997 on a Titan IV-Centaur rocket from Cape Canaveral. Cassini mission was always at risk of cancelation during its development but was saved many times thanks to the great international involvement. The Cassini mission is in fact a NASA-ESA-ASI project. The main effort was made by NASA, which provided the launch facilities, the integration and several instruments; ESA provided the Huygens probe while ASI some of the key elements of the mission such as the high-gain antenna, most of the radio system and important instruments of the Orbiter, such as the Cassini Radar and the visual channel of the VIMS experiment. ASI contributed also to the development of HASI experiment on Huygens probe. The Cassini mission was the first case in which the Italian planetology community was directly involved, developing state of the art hardware for a NASA mission. Given the long duration of the mission, the complexity of the payload onboard the Cassini Orbiter and the amount of data gathered on the satellites of Saturn, it would be impossible to describe all the new discoveries made, therefore we will describe only some selected, paramount examples showing how Cassini’s data confirmed and extended ground-based observations. In particular we will describe the achievements obtained for the satellites Phoebe, Enceladus and Titan. We will also put these examples in the perspective of the overall evolution of the system, stressing out why the selected satellites are representative of the overall evolution of the Saturn system. Cassini is also an example of how powerful could be the coordination between ground-based and space observations. In fact coordinated ground-based observations of Titan were performed at the time of Huygens atmospheric probe mission at Titan on 14 January 2005, connecting the in situ observations by the probe with the general view provided by ground-based measurements. Different telescopes operating at different wavelengths were used, including radio telescopes (up to 17-tracking of the Huygens signal at 2040 MHz), eight large optical observatories studying the atmosphere and surface of Titan, and high-resolution infrared spectroscopy used to observe radiation emitted during the Huygens Probe entry (Witasse et al. J. Geophys. Res. 111:E07S01, 2006).     

The viscous overstability, nonlinear wavetrains, and finescale structure in dense planetary rings

This paper addresses the fine-scale axisymmetric structure exhibited in Saturn's A and B-rings. We aim to explain both the periodic microstructure on 150-220 m, revealed by the Cassini UVIS and RSS instruments, and the irregular variations in brightness on 1-10 km, reported by the Cassini ISS. We propose that the former structures correspond to the peaks and troughs of the nonlinear wavetrains that form naturally in a viscously overstable disk. The latter variations on longer scales may correspond to modulations and defects in the wavetrains' amplitudes and wavelength. We explore these ideas using a simple hydrodynamical model which captures the correct qualitative behaviour of a disk of inelastically colliding particles, while also permitting us to make progress with analytic and semi-analytic techniques. Specifically, we calculate a family of travelling nonlinear density waves and determine their stability properties. Detailed numerical simulations that confirm our basic results will appear in a following paper.     

Synchrotron X-ray diagnostics of cutoff shape of nonthermal electron spectrum at young supernova remnants

Synchrotron X-rays can be a useful tool to investigate electron acceleration at young supernova remnants(SNRs).At present,since the magnetic field configuration around the shocks of SNRs is uncertain,it is not clear whether electron acceleration is limited by SNR age,synchrotron cooling,or even escape from the acceleration region.We study whether the acceleration mechanism can be constrained by the cutoff shape of the electron spectrum around the maximum energy.We derive analytical formulae of the cutoff shape in each case where the maximum electron energy is determined by SNR age,synchrotron cooling and escape from the shock.They are related to the energy dependence of the electron diffusion coefficient.Next,we discuss whether information on the cutoff shape can be provided by observations in the near future which will simply give the photon indices and the flux ratios in the soft and hard X-ray bands.We find that if the power-law index of the electron spectrum is independently determined by other observations,then we can constrain the cutoff shape by comparing theoretical predictions of the photon indices and/or the flux ratios with observed data which will be measured by NuSTAR and/or ASTRO-H.Such study is helpful in understanding the acceleration mechanism.In particular,it will supply another independent constraint on the magnetic field strength around the shocks of SNRs.     

Comparative study of Langmuir probe characteristics in different ionospheric conditions

This paper examines the role played by the high energy tail of the electron distribution function on Langmuir probe characteristics. A model is developed to derive the mean energy and the density of the hyperthermal electrons from probe characteristics for two ionospheric rocket flights involving different plasma conditions. The hyperthermal electrons are shown to influence the electron temperature measurement even if they constitute only a small fraction of the total electron concentration. The influence of the geomagnetic field, the collisions and the velocity of the vehicle on the probe data are also examined.     

The circumstellar environment of Wolf–Rayet stars and gamma-ray burst afterglows

We study the evolution of the circumstellar medium of massive stars. We pay particular attention to Wolf-Rayet stars that are thought to be the progenitors of some long gamma-ray bursts (GRBs). We detail the mass-loss rates we use in our stellar evolution models and how we estimate the stellar wind speeds during different phases. With these details we simulate the interactions between the wind and the interstellar medium to predict the circumstellar environment around the stars at the time of core-collapse. We then investigate how the structure of the environment might affect the GRB afterglow. We find that when the afterglow jet encounters the free-wind/stalled-wind interface, rebrightening occurs and a bump is seen in the afterglow light curve. However, our predicted positions of this interface are too distant from the site of the GRB to reach while the afterglow remains observable. The values of the final wind density,   A _*  , from our stellar models are of the same order (≲1) as some of the values inferred from observed afterglow light curves. We do not reproduce the lowest   A _*  values below 0.5 inferred from afterglow observations. For these cases, we suggest that the progenitors could have been a WO-type Wolf–Rayet (WR) star or a very low-metallicity star. Finally, we turn our attention to the matter of stellar wind material producing absorption lines in the afterglow spectra. We discuss the observational signatures of two WR stellar types, WC and WO, in the afterglow light curve and spectra. We also indicate how it may be possible to constrain the initial mass and metallicity of a GRB progenitor by using the inferred wind density and wind velocity.     

New perspectives on Titan's upper atmosphere from a reanalysis of the Voyager 1 UVS solar occultations

We have reanalyzed the Voyager 1 UVS solar occultations by Titan to expand upon previous analyses and to resolve inconsistencies that have been noted in the scientific literature. To do so, we have developed a detailed model of the UVS detector and improved both the data reduction methods and retrieval techniques. In comparison to the values previously determined by Smith et al. (1982, J. Geophys. Res. 87, 1351-1359) we find N₂ densities that are 25-60% higher, CH₄ densities that are smaller by a factor of 3-7, and C₂H₂ densities that are roughly two orders of magnitude smaller. Our values for the thermospheric temperature are 153-158 K, which are approximately 20-40 K colder than previous estimates. We also report the first-ever determination from Voyager UVS data of density profile information for C₂H₄, HCN, and HC₃N. Finally, we present a simple engineering model that is consistent with our new results in the upper atmosphere and merges smoothly with the model of Yelle et al. (1997, in: HUYGENS Science, Payload and Mission, in: ESA SP, vol. 1177, pp. 243-256) in the lower atmosphere. Our results provide improved constraints for photochemical models and offer scientists a better understanding of Titan's upper atmosphere as we head into the Cassini era in the exploration of the saturnian system.     

Scalar perturbations in two-temperature cosmological plasmas

We study the properties of density perturbations of a two-component plasma with a temperature difference on a homogeneous and isotropic background. For this purpose, we extend the general relativistic gauge-invariant and covariant (GIC) perturbation theory to include a multifluid with a particular equation of state (ideal gas) and imperfect fluid terms due to the relative energy flux between the two species. We derive closed sets of GIC vector and subsequently scalar evolution equations. We then investigate solutions in different regimes of interest. In particular, we study long-wavelength and arbitrary-wavelength Langmuir and ion-acoustic perturbations. The harmonic oscillations are superposed on a Jeans-type instability. We find a generalized Jeans criterion for collapse in a two-temperature plasma, which states that the species with the largest sound velocity determines the Jeans wavelength. Furthermore, we find that within the limit for gravitational collapse, initial perturbations in either the total density or charge density lead to a growth in the initial temperature difference. These results are relevant for the basic understanding of the evolution of inhomogeneities in cosmological models.     

Structure and physics of solar faculae

Si iv, C iv, and O vi resonance lines have been measured above quiet and active solar regions from both pointed OSO-8 instruments. From calibrated profiles, optical depths are computed with three different methods. All three methods provide evidence that the opacity above faculae is lower than above the quiet Sun. From lower and upper limits of the opacity, we derive limits of the electron density. Our first method assumes only that the source function is constant without any geometrical constraint. We find higher densities above faculae than above quiet regions (about a factor 10). A second method allows us to compute the density, temperature gradient and thickness of a plane-parallel model, for active and quiet Sun. Electron densities agree with those of the first method but they lie in the lower range of values previously determined from Skylab. This result can be explained by the moderate level activity of the observed faculae. Appendices give relevant elements of transfer theory and newly computed values of collisional rates.     

Self-similar shocked accretion of collisional gas with radiative cooling

We describe similarity solutions that characterize the collapse of collisional gas on to scale-free perturbations in an Einstein–de Sitter universe. We consider the effects of radiative cooling and derive self-similar solutions under the assumption that the cooling function is a power law of density and temperature, Λ( T , ρ )∝ ρ ^3/2 T . We use these results to test the ability of smooth particle hydrodynamics (SPH) techniques to follow the collapse and accretion of shocked, rapidly cooling gas in a cosmological context. Our SPH code reproduces the analytical results very well in cases that include or exclude radiative cooling. No substantial deviations from the predicted central mass accretion rates or from the temperature, density and velocity profiles are observed in well-resolved regions inside the shock radius. This test problem lends support to the reliability of SPH techniques to model the complex process of galaxy formation.     

Acceleration of the solar wind by whistler waves from coronal holes

We investigate the possibility of an additional acceleration of the high speed solar wind by whistler waves propagating outward from a coronal hole. We consider a stationary, spherically symmetric model and assume a radial wind flow as well as a radial magnetic field. The energy equation consists of (a) energy transfer of the electron beam which excites the whistler waves, and (b) energy transfer of the whistler waves described by conservation of wave action density. The momentum conservation equation includes the momentum transfer of two gases (a thermal gas and an electron beam). The variation of the temperature is described by a polytropic law. The variation of solar wind velocity with the radial distance is calculated for different values of energy density of the whistler waves. It is shown that the acceleration of high speed solar wind in the coronal hole due to the whistler waves is very important. We have calculated that the solar wind velocity at the earth's orbit is about equal to 670 km/sec (for wave energy density about 10^?4 erg cm^?3 at 1.1R⊙). It is in approximate agreement with the observed values.     

Density waves in Cassini UVIS stellar occultations: 1. The Cassini Division

We analyze density waves in the Cassini Division of Saturn's rings revealed by multiple stellar occultations by Saturn's rings observed with the Cassini Ultraviolet Imaging Spectrograph. The dispersion and damping of density waves provide information on the local ring surface mass density and viscosity. Several waves in the Cassini Division are on gradients in the background optical depth, and we find that the dispersion of the wave reflects a change in the underlying surface mass density. We find that over most of the Cassini Division the ring opacity (the ratio of optical depth to surface mass density) is nearly constant and is ∼5 times higher than the opacity in the A ring where most density waves are found. However, the Cassini Division ramp, a 1100-km-wide, nearly featureless region of low optical depth that connects the Cassini Division to the inner edge of the A ring, has an opacity like that of the A ring and significantly less than that in the rest of the Cassini Division. This is consistent with particles in the ramp originating in the A ring and being transported into the Cassini Division through ballistic transport processes. Damping of the waves in the Cassini Division suggests a vertical thickness of 3–6 m. Using a mean opacity of 0.1 cm²/g we find the mass of the Cassini Division, excluding the ramp, is 3.1×¹⁰¹⁶ kg while the mass of the Cassini Division ramp, with an opacity of 0.015 cm²/g, is 1.1×¹⁰¹⁷ kg. Assuming a power-law size distribution for the ring particles, the larger opacity of the main Cassini Division is consistent with the largest ring particles there being ∼5 times smaller than the largest particles in the ramp and A ring.     

Evolution of Mercury's obliquity

Mercury has a near-zero obliquity, i.e. its spin axis is nearly perpendicular to its orbital plane. The value of the obliquity must be known precisely in order to constrain the size of the planet's core within the framework suggested by Peale [Peale, S.J., 1976. Nature 262, 765-766]. Rambaux and Bois [Rambaux, N., Bois, E., 2004. Astron. Astrophys. 413, 381-393] have suggested that Mercury's obliquity varies on thousand-year timescales due to planetary perturbations, potentially ruining the feasibility of Peale's experiment. We use a Hamiltonian approach (free of energy dissipation) to study the spin-orbit evolution of Mercury subject to secular planetary perturbations. We can reproduce an obliquity evolution similar to that of Rambaux and Bois [Rambaux, N., Bois, E., 2004. Astron. Astrophys. 413, 381-393] if we integrate the system with a set of initial conditions that differs from the Cassini state. However the thousand-year oscillations in the obliquity disappear if we use initial conditions corresponding to the equilibrium position of the Cassini state. This result indicates that planetary perturbations do not force short-period, large amplitude oscillations in the obliquity of Mercury. In the absence of excitation processes on short timescales, Mercury's obliquity will remain quasi-constant, suggesting that one of the important conditions for the success of Peale's experiment is realized. We show that interpretation of data obtained in support of this experiment will require a precise knowledge of the spin-orbit configuration, and we provide estimates for two of the critical parameters, the instantaneous Laplace plane orientation and the orbital precession rate from numerical fits to ephemeris data. Finally we provide geometrical relationships and a scheme for identifying the correct initial conditions required in numerical integrations involving a Cassini state configuration subject to planetary perturbations.     

The Cassini Enceladus encounters 2005–2010 in the view of energetic electron measurements

The moon Enceladus, embedded in Saturn’s radiation belts, is the main internal source of neutral and charged particles in the Kronian magnetosphere. A plume of water ice molecules and dust released through geysers on the south polar region provides enough material to feed the E-ring and also the neutral torus of Saturn and the entire magnetosphere. In the time period 2005–2010 the Cassini spacecraft flew close by the moon 14 times, sometimes as low as 25 km above the surface and directly through the plume. For the very first time measurements of plasma and energetic particles inside the plume and its immediate vicinity could be obtained. In this work we summarize the results of energetic electron measurements in the energy range 27 keV to 21 MeV taken by the Low Energy Magnetospheric Measurement System (LEMMS), part of the Magnetospheric Imaging Instrument (MIMI) onboard Cassini in the vicinity of the moon in combination with measurements of the magnetometer instrument MAG and the Electron Spectrometer ELS of the plasma instrument CAPS onboard the spacecraft. Features in the data can be interpreted as that the spacecraft was connected to the plume material along field lines well before entering the high density region of the plume. Sharp absorption signatures as the result of losses of energetic electrons bouncing along those field lines, through the emitted gas and dust clouds, clearly depend on flyby geometry as well as on measured pitch angle/look direction of the instrument. We found that the depletion signatures during some of the flybys show “ramp-like” features where only a partial depletion has been observed further away from the moon followed by nearly full absorption of electrons closer in. We interpret this as partially/fully connected to the flux tube connecting the moon with Cassini. During at least two of the flybys (with some evidence of one additional encounter) MIMI/LEMMS data are consistent with the presence of dust in energetic electron data when Cassini flew directly through the south polar plume. In addition we found gradients in the magnetic field components which are frequently found to be associated with changes in the MIMI/LEMMS particles intensities. This indicates that complex electron drifts in the vicinity of Enceladus could form forbidden regions for electrons which may appear as intensity drop-outs.     

Production and imaging of energetic neutral atoms from Titan’s exosphere: a 3-D model

Energetic Neutral Atoms (ENAs) are formed when singly charged magnetospheric ions undergo charge exchange collisions with exospheric neutral atoms. The energy of the incident ions is almost entirely transferred to the charge exchange produced ENAs, which then propagate along nearly rectilinear ballistic trajectories. Thus the ENAs can be used like photons in order to form an image of the energetic ion distribution. The Cassini spacecraft is equipped with the Ion and Neutral Camera (INCA), a magnetospheric imaging ENA camera which is part of MIMI (Magnetospheric Imaging Instrument) [Mitchell, D.G., Cheng, A.F., Krimigis, S.M., Keath, E.P., Jaskulek, S.E., Mauk, B.H., McEntire, R.W., Roelof, E.C., Williams, D.J., Hsieh, K.C., Drake, V.A., 1993. INCA: the ion neutral camera for energetic neutral imaging of the Saturnian magnetosphere. Opt. Eng. 32, 3096; Krimigis, S.M., Mitchell, D.G., Hamilton, D.C. et al., 1998. Magnetospheric Imaging Instrument (MIMI) on the Cassini Mission to Saturn/Titan, Space Sci. Rev., submitted]. In this paper we study the production of energetic neutral atoms resulting from the interaction of Titan’s inner exosphere with Saturn’s magnetosphere. We then simulate the ENA images of this interaction, that we anticipate to get from INCA, by using a 3-D model of the ENA production. This first necessitated the development of a model for the altitude density profile and composition of the Titan exosphere [Amsif, A., Dandouras, J., Roelof, E.C., 1997. Modeling the production and the imaging of energetic neutral atoms from Titan’s exosphere. J. Geophys. Res. 102, 22,169]. We thus used the Chamberlain model [Chamberlain, J.W., 1963. Planetary corona and atmospheric evaporation. Planet. Space Sci. 11, 901] and included the five major species: H, H₂, N, N₂ and CH₄. The density and composition profiles obtained were then used to calculate the ENA production, considering a proton spectrum measured by Voyager in the Saturnian magnetosphere as the parent ion population. In order to generate simulated ENA images of the interaction of Titan’s exosphere with Saturn’s magnetosphere, we developed a model based on 3-D trajectory tracing techniques for the parent ions. Since the parent ions (E>10 keV) have gyroradii comparable with the Titan diameter, the screening effect of Titan on the parent ion population was also taken into account. This effect results in highly anisotropic ion distributions, which produce ‘shadows’ in the ENA fluxes, in certain directions. These shadows depend on the ENA energy and on the relative geometry of Titan, the magnetic field and the Cassini spacecraft position. The INCA images will thus enable us to remotely sense the ion fluxes and spectra. They are also expected to give information about the magnetic field in the vicinity of Titan and thus to Titan’s interaction with the magnetosphere of Saturn.     

Analysis of energetic electron drop-outs in the upper atmosphere of Titan during flybys in the dayside magnetosphere of Saturn

We discuss the high energy electron absorption signatures at Titan during the Cassini dayside magnetospheric encounters. We use the electron measurements of the Low Energy Measurement System of the Magnetospheric Imaging Instrument. We also examine the mass loading boundary based on the ion data of the Ion Mass Spectrometer sensor of the Cassini Plasma Spectrometer. The dynamic motion of the Kronian magnetopause and the periodic charged particle flux and magnetic field variations – associated with the magnetodisk of Saturn – of the subcorotating magnetospheric plasma creates a unique and complex environment at Titan. Most of the analysed flybys (like T25–T33 and T35–T51) cluster at similar Saturn Local Time positions. However the instantaneous direction of the incoming magnetospheric particles may change significantly from flyby to flyby due to the very different magnetospheric field conditions which are found upstream of Titan within the sets of encounters.The energetic magnetospheric electrons gyrate along the magnetic field lines of Saturn, and at the same time bounce between the mirror points of the magnetosphere. This motion is combined with the drift of the magnetic field lines. When these flux tubes interact with the upper atmosphere of Titan, their content is depleted over approximately an electron bounce period. These depletion signatures are observed as sudden drop-outs of the electron fluxes. We examined the altitude distribution of these drop-outs and concluded that these mostly detected in the exo-ionosphere of Titan and sometimes within the ionosphere.However there is a relatively significant scatter in the orbit to orbit data, which can be attributed to the which can be attributed to the variability of the plasma environment and as a consequence, the induced magnetosphere of Titan. A weak trend between the incoming electron fluxes and the measured drop-out altitudes has also been observed.