Developments in monitoring and modelling small-scale river bed topography

Recent research in fluvial geomorphology has emphasized the spatially distributed feedbacks amongst river channel topography, flow hydraulics and sediment transport. Although understanding of the behaviour of dynamic river channels has been increased markedly through detailed within-channel process studies, less attention has been given to the accurate monitoring and terrain modelling of river channel form using three-dimensional measurements. However, such information is useful in two distinct senses. Firstly, it is one of the necessary boundary conditions for a physically based, deterministic modelling approach in which three-dimensional topography and river discharge drive within-channel flow hydraulics and ultimately spatial patterns of erosion and deposition and therefore channel change. Secondly, research has shown that an alternative means of estimating the medium-term bedload transport rate can be based upon monitoring spatial patterns of erosion and deposition within the river channel. This paper presents a detailed assessment of the distributed monitoring and terrain modelling of river bed topography using a technique that combines rigorous analytical photogrammetry with rapid ground survey. The availability of increasingly sophisticated terrain modelling packages developed for civil engineering application allows the representation of topographic information as a landform surface. Intercomparison of landform surfaces allows visualization and quantification of spatial patterns of erosion and deposition. A detailed assessment is undertaken of the quality of the morphological information acquired. This allow some general comments to be made concerning the use of more traditional methods to monitor and represent small-scale river channel morphology.     

SEDIMENT-REMOVING CAPACITY AND RIVER MOTION DYNAMICS

l INTRODUCTIONT'he landscaPe is mainly shaPed by surface runoff of water through erosion and sedimentahon. mverflows cut the bed, scour the banks and silt the seas. All these are realized by moving sediment frOm oneplace to other places. The caPacity of the flow to remove sediment frOm one place to other places within ariver chanel is called sediment-removing caPacity. It differs frOm the well-defined sediment-capingcapacity For instance, steady flow carries sediment through the river …     

River-aquifer interactions, geologic heterogeneity, and low-flow management

Low river flows are commonly controlled by river-aquifer exchange, the magnitude of which is governed by hydraulic properties of both aquifer and aquitard materials beneath the river. Low flows are often important ecologically. Numerical simulations were used to assess how textural heterogeneity of an alluvial system influences river seepage and low flows. The Cosumnes River in California was used as a test case. Declining fall flows in the Cosumnes River have threatened Chinook salmon runs. A ground water-surface water model for the lower river basin was developed, which incorporates detailed geostatistical simulations of aquifer heterogeneity. Six different realizations of heterogeneity and a homogenous model were run for a 3-year period. Net annual seepage from the river was found to be similar among the models. However, spatial distribution of seepage along the channel, water table configuration and the level of local connection, and disconnection between the river and aquifer showed strong variations among the different heterogeneous models. Most importantly, the heterogeneous models suggest that river seepage losses can be reduced by local reconnections, even when the regional water table remains well below the riverbed. The percentage of river channel responsible for 50% of total river seepage ranged from 10% to 26% in the heterogeneous models as opposed to 23% in the homogeneous model. Differences in seepage between the models resulted in up to 13 d difference in the number of days the river was open for salmon migration during the critical fall months in one given year.     

基于连续方程的河道水流双变量耦合演算模型

针对现有的河道水流洪水演算模型只能模拟单一变量(流量或水位)的问题,以水流连续方程和河段蓄水量的两种不同表达形式(蓄水量等于平均过水断面面积与河段长乘积,蓄水量等于河段平均流量与传播时间的乘积)为基础,对马斯京根模型进行了通用性改进,提出了双变量耦合通用演算模型.选取了四大水系(包括内陆河流和入海河流)的16个河段汛期洪水资料进行模型检验,模型验证考虑了地理范围、不同的河段特征和水力特征、洪水量级等因素,全面地检验了模型结构的合理性和模拟实际洪水的有效性.将双变量耦合通用演算模型与传统的马斯京根法进行了效果比较,结果表明双变量耦合通用演算模型的模拟精度高于马斯京根法,模拟效果比马斯京根法稳定一些,而且具有较好的通用性.     

The channel-geometry method: Guidelines and applications

All river engineering schemes require flood discharge estimates as part of the design and appraisal process. Unfortunately, continuous measurement of flood discharges is limited to those river sites with instrumented gauging stations, which constitute only a small proportion of channel reaches where information is required. Therefore, considerable research effort has been devoted to the development of reliable indirect techniques of flood discharge estimation. Research on the interrelationship of stream channel geometry and river discharge has provided the basis for an indirect method of flood estimation – the channel-geometry method – which employs river channel dimensions alone to estimate discharge characteristics at ungauged river sites. Channel-geometry equations are developed empirically by relating streamflow data from gauging stations and channel dimensions measured from natural river reaches in the vicinity of the gauge, and take the form of power function relations. Once regional channel-geometry equations have been defined, a channel width or channel capacity measurement is the only variable needed to estimate the flood flow characteristics at a specified river site. The method is useful as an alternative to traditional catchment-based approaches or as a rapid reconnaissance technique. In addition to the application for flood discharge prediction, channel-geometry equations could prove helpful in the management of river channels, first, by providing a basis for assessing local deviations in the channel form–discharge relation, deviations which could be employed as indicators of the sensitivity of particular stretches of river channel to change, and secondly, in the computation of natural channel dimensions for use in river channel design and river restoration.     

Properties of fine technogenic sediments and their effect on channel process and self-purification of river water

The role of fine sediments of technogenic origin in channel process is analyzed. The specific features of sedimentation of particles with different density and shape and the issues of flocculation and consolidation of sediments in the bottom part of flow are discussed. Experimental data on the adhesion of particles are given and a relationship for its assessment is proposed. The class of sediments for which the adhesion determines the critical erosion velocity is determined. The processes of river water self-purification and precipitation of fine sediments were compared to show that sedimentation processes play an important role in river water self-purification.     

A study of river channel pattern information recorded by grain size parameters of fluvial sediment

River channel pattern may be regarded as the outcome of streamflow, sediment load, and channel boundary conditions, as can the grain size distribution of bed material. It may therefore be expected that connections should exist between river channel pattern characteristics and the corresponding river bed material grain size parameters. Using data from some Chinese rivers, an attempt has been made to express these connections quantitatively by using statistical methods. The work demonstrates that the river's bed load can be related to the percentage of the traction subpopulation of the bed material shown by the probabilistic plot of grain size cumulative-frequency curve. The study has also revealed some correlations between the bed material grain size parameters of rivers and their channel geometry such as channel width-depth ratio and channel sinuosity. For instance, the higher the ratio of the traction to suspension subpopulation in bed material, the more sinuous, more shallow, and wider the river channel would be. Furthermore, a discrimination function has been given to distinguish between meandering and wandering braided rivers. If the existence of these relationships can be supported by data from more rivers in other regions, then by using them we can postdict palaeoriver channel geometry and its channel pattern character from fluvial sediment grain size parameters of the palaeoriver. This would open a new way to reconstruct the physicogeographical environment in which palaeorivers developed.     

SEDIMENT CARRYING CAPACITY OF SEA CURRENT AND THE TRAINING OF THE YELLOW RIVER MOUTH

1INTRODUCTIONTheYellowRivercarries1.6billiontonsofsedanmentload,rankedthefirstintheworld.Sedimentationinthelowerreachesresultedinfrequentlyshiftoftherivercourses.ThroughoutthehistoryofChina,theYellowRiverhasbeenassociatedwithfloodsandfamine,earningtherivername"China'ssorrow"(Hu,l996).Instabilityoftheriverchannel,especiallythedeltachannel,restraintstheeconomicdevelopmentofthearea.TheDongyingmunicipalgovernment,theShenliOilCorporationandtheYellowRiverMouthManagementBureauofYRCC(Yel…     

Interaction of tides and storm surges at the Elbe River mouth

The main regularities in the interaction of tides and storm surges at river mouths are discussed. A study of the Elbe River mouth area is used to describe the processes of interaction of the eustatic sea level rise, tides, surges, and river flow and special features of formation of maximum water levels. As shown, the intensification of cyclonic activity over the Northern Atlantic in the second half of the XX century resulted in more frequent extremely high storm surges at the Elbe River mouth. An assessment is given for possible changes in the regime of tides and surges at the Elbe River mouth in the XXI century, which may be caused by the acceleration of the eustatic sea level rise. The impact of local hydraulic engineering works (diking, dredging, and channel straightening) on maximum water levels within the town of Hamburg is analyzed.     

Modelling of meander migration in an incised channel

An updated linear computer model for meandering rivers with incision has been developed. The model simulates the bed topography, flow field, and bank erosion rate in an incised meandering channel. In a scenario where the upstream sediment load decreases （e.g., after dam closure or soil conservation）, alluvial river experiences cross section deepening and slope flattening. The channel migration rate might be affected in two ways： decreased channel slope and steeped bank height. The proposed numerical model combines the traditional one-dimensional （1D） sediment transport model in simulating the channel erosion and the linear model for channel meandering. A non-equilibrium sediment transport model is used to update the channel bed elevation and gradations. A linear meandering model was used to calculate the channel alignment and bank erosion/accretion, which in turn was used by the 1D sediment transport model. In the 1D sediment transport model, the channel bed elevation and gradations are represented in each channel cross section. In the meandering model, the bed elevation and gradations are stored in two dimensional （2D） cells to represent the channel and terrain properties （elevation and gradation）. A new method is proposed to exchange information regarding bed elevations and bed material fractions between 1D river geometry and 2D channel and terrain. The ability of the model is demonstrated using the simulation of the laboratory channel migration of Friedkin in which channel incision occurs at the upstream end.     

Processes of delta formation in the mouth area of the Ganges and Brahmaputra rivers

The evolution of the Ganges and Brahmaputra river delta during the Holocene period is discussed. Particular attention is given to the processes of delta formation, the dynamics of the delta hydrographic systems, the channel processes in river branches, as well as to the dynamics of the delta coastline and nearshore zone bed over the last 150–200 years. The calculation of sediment budget in the mouth area of these rivers is presented.     

Fractal sinuosity of stream channels

Analysis of a diverse set of twelve stream channel planforms indicates that at scales relevant to river meandering, river traces are most reasonably treated as fractal curves. The atypically high degree of channel wandering apparent at such scales is a common characteristic of all single-channel streams, while identifiable meandering appears to be only one way in which this tendency is expressed. At smaller scales of view river paths have shapes of smooth curves appropriate to Euclidian geometry, and toward larger scales a distinct change in degree of wandering marks the transition to bends that are considered to be changes in general river course rather than parts of channel pattern. This analysis method provides a natural, objective calculation of river sinuosity as well as other parameters that more completely specify channel planform.     

Daily discharge estimation at ungauged river sites using remote sensing

A methodology is developed to estimate daily river discharge at an ungauged site using remote sensing data. Use is made of ERS‐2 and ENVISAT satellite altimetry to provide a time series of river channel stage levels and longitudinal channel slope and Landsat satellite imagery to provide a range of channel widths over a 50 km reach of river. The data are substituted into the Bjerklie et al. ( 2003 ) equation, which is based on the Manning's resistance equation and has been developed using a global database of channel hydraulic information and discharge measurements. Our methodology has been applied at three locations on the Mekong and Ob Rivers and validated against daily in situ discharge measurements. The results show Nash–Sutcliffe efficiency values of 0.90 at Nakhon Phanom and 0.86 at Vientiane on the Mekong, and 0.86 at Kalpashevo on the Ob. Copyright © 2012 John Wiley & Sons, Ltd.     

Hydrological and morphological processes in the mouth area of the Columbia River (United States) and their changes under the impact of large-scale hydroengineering works

The main hydrological and morphological features of the Columbia River mouth area, including its tidal estuary, are discussed. Close attention is given to the characteristics of large-scale hydraulic projects in the river basin as well as to dredging and channel training operations in the river mouth area and to the assessment of the impact of these operations on hydrological and morphological processes. Variations in the regime of river flow after its regulation, processes of dynamic interaction and mixing of river and sea water in the estuary are characterized. Changes of the mouth bar and sea coasts near the Columbia River mouth as a result of construction of stream-training jetties are discussed.     

The Coefficient of Friction in Channel Flows

The dimensionless Darcy–Weisbach coefficient of friction is used to evaluate the drag in channel flows. A developed turbulent flow with a quadratic drag law is considered. The dependence of the coefficient of friction on the cross-section shape of the channel flow is examined. A coefficient of the channel shape is introduced, which depends on the wetted perimeter and the flow width and allows the complicated geometry of the river cross-section to be taken into account in calculating the drag. The drag estimates calculated using the suggested technique are compared with other authors' estimates for flumes and rivers.     

A hydro‐economic modelling framework for flood damage estimation and the role of riparian vegetation

A modelling framework for the quick estimate of flood inundation and the resultant damages is developed in this paper. The model, called the flood economic impact analysis system (FEIAS), can be applied to a river reach of any hydrogeological river basin. For the development of the integrated modelling framework, three models were employed: (1) a modelling scheme based on the Hydrological Simulation Program FORTRAN model that was developed for any geomorphological river basin, (2) a river flow/floodplain model, and (3) a flood loss estimation model. The first sub‐model of the flood economic impact analysis system simulates the hydrological processes for extended periods of time, and its output is used as input to a second component, the river/floodplain model. The hydraulic model MIKE 11 (quasi‐2D) is the river/floodplain model employed in this study. The simulated flood parameters from the hydraulic model MIKE 11 (quasi‐2D) are passed, at the end of each time step, to a third component, the flood loss model for the estimation of flood damage. In the present work, emphasis was given to the seasonal variation of Manning's coefficient (n), which is an important parameter for the determination of the flood inundation in hydraulic modelling. High values of Manning's coefficient for a channel indicate high flow resistance. The riparian vegetation can have a large impact on channel resistance. The modelling framework developed in this paper was used to investigate the role of riparian vegetation in reducing flood damage. Moreover, it was used to investigate the influence of cutting riparian vegetation scenarios on the flow characteristics. The proposed framework was applied to the downstream part of the Koiliaris River basin in Crete, Greece, and was tested and validated with historical data. Copyright © 2012 John Wiley & Sons, Ltd.     

Historical analysis indicates seepage control on initiation of meandering

In analytical and numerical models of river meandering, initiation of meandering typically occurs uniformly along the streamwise coordinate in the channel. Based on a historical analysis of the Nierskanaal, here we show how and under which circumstances meandering has initiated in isolated sections of a channel. The Nierskanaal was constructed by the end of the 18th century, as a straight channel between the river Niers and the river Meuse. The purpose of this measure was to reduce flood risk in the downstream reaches of the river Niers. The banks on the Dutch part of the channel were left unprotected and developed into a morphodynamically active channel, featuring a meandering planform and valley incision. The planform development and incision process is analysed using topographic maps and airborne LiDAR data. Meandering initiated in three sections of the channel, where the channel sinuosity developed asynchronously. Sedimentary successions in the study area show layers of iron oxide, indicating groundwater seepage from aeolian river dunes and river deposits located nearby. Only at the spots where meandering has initiated iron oxide is found close to the surface level. This provides a clue that seepage triggered bank erosion by increasing moisture content of the banks. The isolated meandering sections expanded in the longitudinal direction. Valley incision has developed in the first decades after the construction of the channel, and diminished after a gravel layer was reached. Gravel was deposited in the downstream half of the channel bed, acting as an armouring layer. The spatial variation in meandering behaviour, as observed in the Nierskanaal, justifies efforts to implement the influence of floodplain heterogeneity and the effect of seepage on bank erosion in meander models. Copyright © 2013 John Wiley & Sons, Ltd.     

Physics‐based numerical modelling of large braided rivers dominated by suspended sediment

Physics‐based models have been increasingly developed in recent years and applied to simulate the braiding process and evolution of channel units in braided rivers. However, limited attention is given to lowland braided rivers where the transport of suspended sediment plays a dominant role. In the present study, a numerical model based on the basic physics laws of hydrodynamics and sediment transport is used to simulate the evolution process of a braided river dominated by suspended load transport. The model employs a fractional method to simulate the transport of graded sediments and uses a multiple‐bed‐layer approach to represent the sediment sorting process. An idealized braided river has been produced, with the hydrodynamic, sediment transport and morphological processes being analysed. In particular, the formation process of local pool–bar units in the predicted river has been investigated. A sensitivity analysis has also been undertaken to investigate the effects of grid resolution and an upstream perturbation on the model prediction. A variety of methods are applied to analyse the geometrical and topographical properties of the modelled river. Self‐organizing characteristics related to river geometry and topography are analysed by state‐space plots, which indicate a close relationship with the periodical erosion and deposition cycles of braiding. Cross‐sectional topography and slope frequency display similar geometries to natural rivers. Scaling characteristics are found by correlation analysis of bar parameters. Copyright © 2014 John Wiley & Sons, Ltd.