Trapping Ionic Mercury Using Different Adsorbents

Of recent, adsorption process has gained a lot of attention as a cheap and effective means of removing trace metals from wastewater prior to discharge into water bodies. Being flexible in design and operation, the process has enabled an optimal recovery of trace metals such that the treated effluents meet the desired standards for waste disposal. Mercury is a toxicant released into the environment from natural and anthropogenic sources. It is notorious for having an unusual tendency to bio‐accumulate and persist in the food chain. Presence of mercury in food, especially those of aquatic sources has drastic implications on human health. Therefore, efforts have been made to develop and optimize low‐cost activated carbon (AC) as adsorbents for scavenging mercury from aqueous effluents. Herein, how mercury accumulates across the food chain, its health implications, and the recent advancement in the use of low‐cost ACs as adsorbent for trapping mercury from wastewater are highlighted. Relationship between the mercury removal efficiency and the surface morphology of the adsorbents as well as the influence of prevailing experimental condition on the sorption process were addressed. Challenges and future prospects of the use of low‐cost adsorbents in addressing mercury pollution in the environment are discussed.     

Adsorption of Cadmium Ions from Aqueous Solution Using Granular Activated Carbon and Activated Clay

The present study was aimed at removing cadmium ions from aqueous solution through batch studies using adsorbents, such as, granular activated carbon (GAC) and activated clay (A‐clay). GAC was of commercial grade where as the A‐clay was prepared by acid treatment of clay with 1 mol/L of H₂SO₄. Bulk densities of A‐clay and GAC were 1132 and 599 kg/m³, respectively. The surface areas were 358 m²/g for GAC and 90 m²/g for A‐clay. The adsorption studies were carried out to optimize the process parameters, such as, pH, adsorbent dosage, and contact time. The results obtained were analyzed for kinetics and adsorption isotherm studies. The pH value was optimized at pH 6 giving maximum Cd removal of 84 and 75.2% with GAC and A‐clay, respectively. The adsorbent dosage was optimized and was found to be 5 g/L for GAC and 10 g/L for A‐clay. Batch adsorption studies were carried out with initial adsorbate (Cd) concentration of 100 mg/L and adsorbent dosage of 10 g/L at pH 6. The optimum contact time was found to be 5 h for both the adsorbents. Kinetic studies showed Cd removal a pseudo second order process. The isotherm studies revealed Langmuir isotherm to better fit the data than Freundlich isotherm.     

Removal of Selenium by Adsorption onto Granular Activated Carbon (GAC) and Powdered Activated Carbon (PAC)

The present work involves the study of Se(IV) adsorption onto granular activated carbon (GAC) and powdered activated carbon (PAC). The adsorbents are coated with ferric chloride solution for the effective removal of selenium. The physico-chemical characterization of the adsorbents is carried out using standard methods, e. g., proximate analysis, scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR), thermo-gravimetric (TGA) and differential thermal analysis (DTA), etc. The FTIR spectra of the GAC and PAC indicate the presence of various types of functional groups, e. g., free and hydrogen bonded OH groups, silanol groups (Si-OH), alkenes, and CO group stretching from aldehydes and ketones on the surface of adsorbents. Batch experiments are carried out to determine the effect of various factors such as adsorbent dose (w), initial pH, contact time (t), and temperature (T) on the adsorption process. The optimum GAC and PAC dosage is found to be 10 g/L and 8 g/L, respectively, for Se(IV) removal with C₀ = 100 mg/L. The percent removal of Se(IV) increases with increasing adsorbent concentration, while removal per unit weight of adsorbent increases with decreasing adsorbent concentration. Se(IV) adsorption onto both the GAC and PAC adsorbents is high at low pH values, and decreases with increased initial pH. The results obtained are analyzed by various kinetic models. The parameters of pseudo-first order, pseudo-second order kinetics, and Weber-Morris intra particle kinetics are determined. It is seen that the sorption kinetics of Se(IV) onto GAC and PAC can be best represented by the pseudo-second order kinetic model.     

Removal of EDTA from Aqueous Solutions Using Activated Carbon Prepared from Rubber Wood Sawdust: Kinetic and Equilibrium Modeling

Adsorptive removal of EDTA (ethylenediaminetetraacetic acid) from aqueous solution was studied using steam pyrolyzed activated carbon. Rubber wood sawdust, obtained from a local timber facility at Kodangavila, Trivandrum, Kerala, India was used as the precursor for the production of the activated carbon. Batch adsorption experiments were employed to monitor and optimize the removal process. The experimental parameters, i. e., solution pH, agitation time, initial EDTA concentration and adsorbent dosage, affecting the adsorption of EDTA onto sawdust activated carbon (SDAC) were optimized. The inner core mechanism for the interaction between EDTA and SDAC, which resulted in the adsorption process, was also discussed. The change in amount of EDTA adsorbed onto SDAC and CAC (commercial activated carbon) was compared over a wide range of pH (2.0–8.0). The maximum removal of EDTA took place in the pH range of 4.0–6.0 for SDAC and 5.0–5.5 for CAC, which demonstrates the effectiveness of the former adsorbent. Kinetic as well as equilibrium studies were performed to determine the rate constant and adsorption capacity, respectively. The adsorption kinetic data was fitted with pseudo‐first‐order kinetics and the equilibrium data was shown to follow the Langmuir isotherm model. These observations explain the formation of a monolayer of EDTA on the surface of SDAC as confirmed by the slow approach to equilibrium after 4 h of contact time. The adsorption capacity of SDAC for the removal of EDTA was 0.526 mmol/g and is seen to be greater than that of CAC and other reported adsorbents (0.193–0.439 mmol/g). Finally, it is clear that the production of steam pyrolyzed activated carbon in the presence of K₂CO₃ greatly enhanced EDTA removal and resulted in a product with possible commercial value for wastewater treatment strategies.     

Response Surface Optimization of Acid Red 119 Dye Adsorption by Mixtures of Dried Sewage Sludge and Sewage Sludge Ash

The mixtures of dried sewage sludge (DSS) and sewage sludge ash were studied for removal of acid red 119 (AR119) dye as a new, more environmental friendly, and low cost adsorbent. For this purpose, response surface methodology was applied to optimize the dye removal efficiency and turbidity of treated dye solutions as two individual responses. Results revealed that an optimum condition under specified constraints (dye removal efficiency >95% and turbidity <50 NTU) was obtained at a contact time of 60 min, 40 wt% DSS in the mixture, an initial pH of 6, and an initial dye concentration of 200 mg dye/L in distilled water. Under the optimal condition, dye removal efficiency of 94.98% and effluent turbidity of 24.9 NTU was observed. In further studies, at optimum condition, the effect of some additives on adsorption process and desorption/reusability of adsorbent was investigated. It was observed that removal efficiency was significantly decreased to 83.76% when a simulated dye wastewater (containing the selected dye, acetic acid, and Glauber's salt dissolved in tap water) was used. Desorption studies revealed that AR119 dye could be well removed from dye‐loaded adsorbent by 0.3 M NaOH solution.     

Malachite Green Removal from Aqueous Solution by the Peel of Cucumis sativa Fruit

This study investigates the potential use of activated carbon prepared from the peel of Cucumis sativa fruit for the removal of malachite green (MG) dye from simulated wastewater. The effects of different system variables, adsorbent dosage, initial dye concentration, pH, and contact time were investigated and optimal experimental conditions were ascertained. The results showed that when the amount of the adsorbent increased, the percentage of dye removal increased accordingly. Optimum pH value for dye adsorption was 6.0. Maximum dye was sequestered within 50 min of the start of every experiment. The adsorption of MG followed the pseudo‐second‐order rate equation and fits the Langmuir, Freundlich, Dubinin–Radushkevich (D–R), and Tempkin equations well. The maximum removal of MG was obtained at pH 6 as 99.86% for adsorbent dose of 1 g/50 mL and 25 mg L^?1 initial dye concentration at room temperature. Activated carbon developed from the peel of C. sativa fruit can be an attractive option for dye removal from diluted industrial effluents since test reaction made on simulated dyeing wastewater showed better removal percentage of MG.     

Removal of Cadmium from Aqueous Solution Using Castor Seed Hull: A Kinetic and Equilibrium Study

The effects of various parameters such as initial concentration, adsorbent loading, pH, and contact time on kinetics and equilibrium of adsorption of Cd²⁺ metal ion from its aqueous solution by castor seed hull (CSH) and also by activated carbon have been investigated by batch adsorption experiments. The amount of adsorption increases with initial metal ion concentration, contact time, solution pH, and the loading of adsorbent for both the systems. Kinetic experiments indicate that adsorption of cadmium metal ion on both CSH and on activated carbon consists of three steps – a rapid adsorption of cadmium metal ion, a transition phase, and an almost flat plateau region. This has also been confirmed by the intraparticle diffusion model. The lumped kinetic results show that the cadmium adsorption process follows a pseudo‐second order rate law. The kinetic parameters including the rate constant are determined at different initial metal ion concentrations, pH, amount, and type of adsorbent, respectively. The Langmuir and Freundlich adsorption isotherm models are used to describe the experimental data. The Langmuir model yields a better correlation coefficient than the other model. A comparison of the monolayer adsorption capacity (q_m) of CSH, activated carbon, and several other reported adsorbents has been provided. The value of separation factor (R_L) calculated from the Langmuir equation also gives an indication of favorable adsorption of the metal ion. From comparative studies, it has been found that CSH is a potentially attractive adsorbent than commercial activated carbon for cadmium metal ion (Cd²⁺) removal.     

Progress in the Development of Control Strategies for the SBR Process

The sequencing batch reactor (SBR) process has shown great success in the treatment of industrial wastewater from intermittent discharge factories and for the treatment of domestic wastewater from medium or small towns. As automation technology has developed, many studies have been conducted to determine the optimal conditions for the SBR process. This review outlines the progress and application of control strategies that have been developed for the SBR process and provides a summary and comparison of the advantages and disadvantages of various control strategies, especially fixed‐time control strategies and various real‐time control strategies. Moreover, an analysis and discussion of novel optimal control methods for biologic nutrient removal are provided. Although previous studies in this field have greatly enriched our understanding of SBR systems, it is clear that many unsolved problems remain. Therefore, a summary of unanswered questions regarding control strategies for the SBR process is provided and future research directions are suggested.     

Adsorption of Selenium Using Bagasse Fly Ash

The present work involves the study of Se(IV) adsorption onto bagasse fly ash. The adsorbents were coated with a ferric chloride solution for the effective removal of selenium. The physico‐chemical characterization of the adsorbent was carried out using standard methods, e. g., proximate analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, thermo‐gravimetric analysis and differential thermal analysis. Batch experiments were carried out to determine the effect of various parameters such as adsorbent dose, initial pH, contact time, and temperature on the adsorption process. Results obtained from these studies were analyzed using various kinetic models and isotherms. Se(IV) adsorption onto adsorbent was high at low pH values, and decreased with an increase in initial pH. A temperature study showed that the uptake of Se(IV) was greatest at 293 K, within the temperature range studied. The parameters of pseudo first order, pseudo second order, and Weber‐Morris intra‐particle kinetic models were determined. Equilibrium isotherms were analyzed using Langmuir, Freundlich, and Temkin isotherms. Error analyses were also carried out using hybrid fractional error function and Marquardt's percent standard deviation.     

Adsorptive Removal of Acid Blue 15: Equilibrium and Kinetic Study

Activated carbons prepared from sunflower seed hull have been used as adsorbents for the removal of acid blue 15 (AB‐15) from aqueous solution. Batch adsorption techniques were performed to evaluate the influences of various experimental parameters, e. g., temperature, adsorbent dosage, pH, initial dye concentration and contact time on the adsorption process. The optimum conditions for AB‐15 removal were found to be pH = 3, adsorbent dosage = 3 g/L and equilibrium time = 4 h at 30°C. The adsorption of AB‐15 onto the adsorbent was found to increase with increasing dosage. It was found from experimental results that the Langmuir isotherm fits the data better than the Freundlich and Temkin isotherms. The maximum adsorption capacity, Q_m (at 30°C) was calculated for SF1, SF2, and SF3 as 75, 125 and 110 mg g^–1 of adsorbent, respectively. It was found that the adsorption follows pseudo‐second order kinetics. The thermodynamic parameters such as ΔG°, ΔH°, and ΔS° were also evaluated. The activated carbons prepared were characterized by FT‐IR, SEM and BET analysis.     

Adsorption of Thallium(I) Ions Using Eucalyptus Leaves Powder

Using batch method, the adsorption of thallium(I) ions from aqueous solutions on eucalyptus leaves powder, as a low cost adsorbent, was studied. The effect of various modification of considered adsorbent on the adsorption percentage of Tl(I) is an important feature of this study. The results showed that the unmodified and acidic modified adsorbent are the poor adsorbents for the Tl(I) ions while basic modified adsorbent is a suitable adsorbent. Also, the effect of some experimental conditions such as solution initial pH, agitation speed, contact time, sorbent dosage, temperature, particle size, and thallium initial concentration was studied. The results showed that the adsorption percentage depends on the conditions and the process is strongly pH‐dependent. The satisfactory adsorption percentage of Tl(I) ions, 81.5%, obtained at 25 ± 1°C. The equilibrium data agreed fairly better with Langmuir isotherm than Freundlich and Temkin models. The value of q_m that was obtained by extrapolation method is 80.65 mg g^?1. Separation factor values, R_L, showed that eucalyptus leaves powder is favorable for the sorption of Tl(I). The negative values of ΔH⁰ and ΔS⁰ showed that the Tl(I) sorption is an exothermic process and along with decrease of randomness at the solid–solution interface during sorption, respectively.     

Zur Adsorptionsbehandlung von Abwässern eines pharmazeutischen Betriebes

The activity of two adsorbent polymers on the basis of polystyrene and of an activated carbon for the removal of organochlorine substances as well as of substances which are characterized by the COD-Cr or the ultraviolet absorption in the wastewater of a pharmaceutical enterprise is assessed in batch and filtration experiments. The results show a good take-up of the organochlorine compounds by the polymers. Activated carbon showed partially the best values for process wastewater.     

Removal of COD from Industrial Effluent Containing Indigo Dye Using Adsorption Method by Activated Carbon Cloth: Optimization,Kinetic, and Isotherm Studies

The pollution of underground and surface water streams is a tremendous environmental problem. Adsorption, in which activated carbon (AC) is used as an adsorbent, is one of efficient procedures to remove organic and inorganic pollutants from industrial wastewaters. Activated carbon fiber (ACF), a newly developed form of AC, has high adsorption rate and surface area and can be used for the treatment of industrial wastewaters. In this work, ACF was prepared by physicochemical activation method from kenaf and we studied its ability in the treatment of indigo‐containing wastewater produced from a dying factory. The filtered wastewater was treated via adsorption by ACF, and response surface experimental design method was used to study the effect of ACF dosage, contact time, temperature, and pH of the wastewater on the removal process. ACF dosage of 0.256 g, temperature of 12.5°C, pH 8.5, and contact time of 125 min were optimum treatment conditions. The adsorption process obeys pseudo‐second‐order kinetic and Freundlich isotherm models.     

Adsorption of Chromium(III), Nickel(II), and Copper(II) from Aqueous Solution by Activated Alumina

The possible use of activated alumina powder (AAP) as adsorbent for Cr(III), Ni(II), and Cu(II) from synthetic solutions was investigated. The effect of various parameters on batch adsorption process such as pH, contact time, adsorbent dosage, particle size, temperature, and initial metal ions concentration were studied to optimize the conditions for maximum metal ion removal. Both higher (molar) and lower (ppm) initial metal ion concentration sets were subjected to adsorption on AAP. Adsorption process revealed that equilibrium was established in 50 min for Cr(III) at pH 4.70, 80 min for Ni(II) at pH 7.00, and 40 min for Cu(II) at pH 3.02. Percentage removal was found to be highest at 55°C for Cr(III) and Ni(II) with 420 µm and 45°C for Cu(II) with 250‐µm particle size AAP. A dosage of 2 g for Cr(III), 8 g for Ni(II), and 10 g Cu(II) gave promising data in the metal ion removal. The adsorption process followed Langmuir as well as Freundlich models. The thermodynamics of adsorption of these metal ions on activated aluminum indicated that the adsorption was spontaneous and endothermic in nature. Present study indicates that AAP can act as a promising adsorbent for industrial wastewater treatment.     

Abwasserreinigung in der Produktion von Phenolformaldehydharzen

As investigations on model solutions and real wastewaters with 30 … 33 g/l phenol and 5 … 10 g/l formaldehyde as well as pH = 2 … 3 have shown, the following technique of sewage purification proves to be optimal: condensation with addition of 7 g/l sulphuric acid at 98 °C, settling of the condensation products formed for 8 h, centrifugation of the supernatant and adsorption on activated carbon or a polymer sorbent (XAD 4). Preference should be given to activated carbon. The residual concentrations amount to 0.1 mg/l for both phenol and formaldehyde. The adsorbents are largely fully regenerated with methanol, the regeneration solution containing 11 … 20 g/l phenol.     

Design and Development of Onsite Biofilter Unit for Effective Remediation of Contaminants from Wastewater

Agricultural biomass is proven ecofriendly and effective adsorbent for the remediation of contaminants from wastewater. Here, rice husk biochar (600 °C) prepared by a one-step pyrolysis method is used for the remediation of different contaminants in real samples. An onsite biofilter unit is fabricated with parallel trenches of different layers of coconut coir and biochar and is used as a biofiltration unit. The efficiency of the designed unit is assessed for the removal of different contaminants in pilot-scale experiments. Results show that removal efficiency varies from metal to metal and ranges from 5.52% to 90.76% using the biofilter unit. Fourier-transform infrared spectroscopy, scanning electron microscopy with energy dispersive X-ray analysis, carbon, hydrogen, nitrogen, and Brunauer–Emmett–Teller analysis before and after the adsorption represent the changes in the morphology and surface functionalization of the biochar. Results indicate that the designed biofilter unit could also be used as a promising agent for the remediation of pharmaceutical and other emerging contaminants from wastewater.     

Removal of Congo Red from Aqueous Solution by Sorption on Organified Rectorite

Batch sorption technique was carried out for the removal of anionic dye Congo red (CR) from aqueous solution using raw rectorite (R‐REC) and organified rectorite (CTA⁺‐REC) modified by cetyltrimethylammonium bromide (CTAB) as adsorbents. The effects of organification degree of CTA⁺‐REC as well as the process parameters including the pH of dye solution, sorption time, and initial dye concentration on adsorption capacity for CR were investigated and the sorption kinetics was also evaluated. The results showed that the sorption behaviors of R‐REC and CTA⁺‐REC for CR followed pseudo‐second‐order kinetic model and the sorption equilibrium data perfectly obeyed the Langmuir isotherm. The thermodynamic parameters including entropy of sorption (ΔS⁰), enthalpy of sorption (ΔH⁰), and Gibbs free energy of sorption (ΔG⁰) were obtained and analyzed. Fourier transform infrared study revealed that a chemisorption process occurred between CR and CTA⁺‐REC. REC modified by cationic surfactants showed the higher adsorption capacities for CR compared to R‐REC and in theory would be used as an efficient and promising adsorbent for the removal of anionic dyes in wastewater treatment.     

Biosorption of Dyes by Natural and Activated Vine Stem. Interaction between Biosorbent and Dye

In the present study, the vine stem and modified vine stem were used as low cost adsorbents for the removal of acidic and basic dyes from aqueous solutions. A comparative study was also carried out with activated carbon obtained from vine stem and then the adsorption capacities of all adsorbents were evaluated by batch adsorption process. The effects of various adsorption parameters (initial pH, particle size, and contact time) were investigated. The modification of the vine stem with nitric acid increased its adsorption capacity for the basic dye. Both, vine stem and modified vine stem exhibited higher adsorption capacities than activated carbon. The adsorption capacities were found to be 322.58, 250, and 200 mg g^?1 for modified, natural vine stem, and activated carbon, respectively. In the case of acidic dye, the pH strongly affected the adsorption capacity and the maximum dye uptake was observed at pH 2 for all adsorbents. The acidic dye adsorption was lower compared to basic dye on both biosorbents and activated carbon tested. The maximum acidic dye adsorption values (58.82 and 59.88 mg g^?1) were obtained with the vine stem and activated carbon, respectively. In the case of lignocellulosic adsorbents, both surface charge and surface groups had main effect on the adsorption of basic dye, while adsorption mechanism in activated carbon was mainly through the physical adsorption. The results of comparative adsorption capacity of adsorbents indicated that vine stem or modified vine stem can be used as a low cost alternative to activated carbon in aqueous solution for basic dye removal.     

Concentrations of Artificial Sweeteners and Their Ratios with Nutrients in Septic System Wastewater

This study reports the first comprehensive data set of characteristic concentrations of four artificial sweeteners: acesulfame (ACE), sucralose (SUC), saccharin (SAC), and cyclamate (CYC), and their ratios with nutrients, for untreated septic system wastewater. Samples were collected from the tanks of 19 different septic systems from across Ontario, Canada; these had a variety of usages, from single‐family cottages to multiple‐dwelling (campground or resort) facilities and had no additional treatment systems. The artificial sweetener concentrations and their relative proportions were highly variable in some cases, both temporally for several individual tanks and from site‐to‐site. Variability tended to be lower for multiple‐dwelling compared to single‐dwelling systems. This variability likely reflects differing use of artificial sweetener‐containing products. The median concentrations for the complete data set of all four artificial sweeteners (in a range of 10 to 60 μg/L) were of a similar order of magnitude, but slightly higher, than has generally been reported for wastewater treatment plant influent (though these vary substantially globally). Both SUC and ACE provided adequate positive linear relationships for dissolved nitrogen and phosphorus in the septic tanks, while a summation of ACE and SUC concentrations also gave a strong correlation. In contrast, CYC and SAC showed poor linear correlation with these nutrients. These reported ranges for artificial sweetener concentrations and ratios with nutrients may be used in future studies to estimate the contributions of nutrients or other wastewater constituents (e.g., pharmaceuticals, bacteria, and viruses) from domestic septic systems to groundwater, including water supply or irrigation wells, and nearby surface water bodies.