Late‐glacial to Holocene depositional architecture of the Ombrone palaeovalley system (Southern Tuscany,Italy): Sea‐level,climate and local control in valley‐fill variability

The Ombrone palaeovalley was incised during the last glacial sea‐level fall and was infilled during the subsequent Late‐glacial to Holocene transgression. A detailed sedimentological and stratigraphic study of two cores along the palaeovalley axis led to reconstruction of the post‐Last Glacial Maximum valley‐fill history. Stratigraphic correlations show remarkable similarity in the Late‐glacial to early‐Holocene succession, but discrepancy in the Holocene portion of the valley fill. Above the palaeovalley floor, about 60 m below sea‐level, Late‐glacial sedimentation is recorded by an unusually thick alluvial succession dated back to ca 18 cal kyr bp . The Holocene onset was followed by the retrogradational shift from alluvial to coastal facies. In seaward core OM1, the transition from inner to outer estuarine environments marks the maximum deepening of the system. By comparison, in landward core OM2, the emplacement of estuarine conditions was interrupted by renewed continental sedimentation. Swamp to lacustrine facies, stratigraphically equivalent to the fully estuarine facies of core OM1, represent the proximal expression of the maximum flooding zone. This succession reflects location in a confined segment of the valley, just landward of the confluence with a tributary valley. It is likely that sudden sediment input from the tributary produced a topographic threshold, damming the main valley course and isolating its landward segment from the sea. The seaward portion of the Ombrone palaeovalley presents the typical estuarine backfilling succession of allogenically controlled incised valleys. In contrast, in the landward portion of the system, local dynamics completely overwhelmed the sea‐level signal, following marine ingression. This study highlights the complexity of palaeovalley systems, where local morphologies, changes in catchment areas, drainage systems and tributary valleys may produce facies patterns significantly different from the general stratigraphic organization depicted by traditional sequence‐stratigraphic models.     

Down‐slope facies variability within deep‐water channel systems: Insights from the Upper Cretaceous Cerro Toro Formation,southern Patagonia

In southern Patagonia, outcrops of the Upper Cretaceous Cerro Toro Formation preserve a >150 km long deep‐water axial channel belt in the Magallanes–Austral Basin, providing a unique opportunity to investigate longitudinal variations in the depositional characteristics of a deep‐water channel system. This study documents sedimentological, stratigraphical and geochronological data from the Cerro Toro Formation in the Argentine sector of the basin. New results are integrated with previous work from the Chilean basin sector to conduct a basin‐scale comparison of the timing of deposition, provenance and lithofacies proportions. The Cerro Toro channel belt includes a nearly 1000 m thick section characterized by high‐density turbidites and mass‐wasting deposits. Two ash beds from the base of the section yield U–Pb zircon ages of 90·4 ± 2 Ma and 88·0 ± 3 Ma, indicating similar initiation ages as documented in the Chilean sector. The U–Pb detrital zircon age spectra from samples in the study area reveal similar provenance trends to samples from the Chilean basin sector, with peak age populations at 310 to 260 Ma, 160 to 135 Ma and 110 to 82 Ma. The maximum depositional age of the channel belt in the Argentine sector is 87·8 ± 1·5 Ma and all new geochronology data corroborate an 86 to 80 Ma depositional age for the main Cerro Toro channel belt. Statistical analyses of 7370 beds from nearly 8000 m of new and previously published stratigraphic sections along the entire outcrop belt suggest progressive variations in the down‐system proportion of lithofacies. In the up‐slope region, lithofacies representing mass wasting processes (for example, debris‐flow and mass‐transport deposits) account for ca 29% of the stratigraphic thickness, as opposed to 5% in the down‐slope region of the channel belt, where turbidity current deposits are more prevalent. The proportion of beds >1 m thick also decreases systematically down slope, particularly for conglomeratic turbidite deposits. This work highlights that: (i) the proportion of thick beds and distribution of lithofacies are key down‐system changes in the stratigraphic fill of this deep‐water channel belt; (ii) detrital zircon trends suggest a relatively well‐mixed longitudinal depositional system; and (iii) geochronology of the main Cerro Toro outcrop belt supports but does not necessitate the model of a single, roughly age‐equivalent, channel system. This study has implications for understanding the downslope variability in depositional processes, stratigraphic architecture and reservoir quality of submarine channel systems.     

Geometry,spatial arrangement and origin of carbonate grain‐dominated,scour‐fill and event‐bed deposits: Late Jurassic Jubaila Formation and Arab‐D Member,Saudi Arabia

Outcrop analogues of the Late Jurassic lower Arab‐D reservoir zone in Saudi Arabia expose a succession of fining‐upward cycles deposited on a distal middle‐ramp to outer‐ramp setting. These cycles are interrupted by erosional scours that incise up to 1·8 m into underlying deposits and are infilled with intraclasts up to boulder size (1 m diameter). Scours of similar size and infill are not commonly observed on low‐angle carbonate ramps. Outcrops have been used to characterize and quantify facies‐body geometries and spatial relationships. The coarse grain size of scour‐fills indicates scouring and boulder transport by debris or hyperconcentrated density flows strengthened by offshore‐directed currents. Longitudinal and lateral flow transformation is invoked to produce the ‘pit and wing’ geometry of the scours. Scour pits and wings erode up to 1·8 m and 0·7 m deep, respectively, and are on average 50 m wide between wing tips. The flat bases of the scours and their lack of consistent aspect ratio indicate that erosion depth was limited by the presence of cemented firmgrounds in underlying cycles. Scours define slightly sinuous channels that are consistently oriented north–south, sub‐parallel to the inferred regional depositional strike of the ramp, suggesting that local palaeobathymetry was more complex than commonly assumed. Weak lateral clustering of some scours indicates that they were underfilled and reoccupied by later scour incision and infill. Rudstone scour‐fills required reworking of material from inner ramp by high‐energy, offshore‐directed flows, associated with storm action and the hydraulic gradient produced by coastal storm setup, to generate erosion and sustain transport of clasts that are generally associated with steeper slopes. Quantitative analysis indicates that these coarse‐grained units have limited potential for correlation between wells as laterally continuous, highly permeable reservoir flow units, but their erosional and locally clustered character may increase effective vertical permeability of the Arab‐D reservoir zone as a whole.     

Anatomy of falling‐stage deltas in the Turonian Ferron Sandstone of the western Henry Mountains Syncline,Utah: Growth faults,slope failures and mass transport complexes

Falling‐stage deltas are predicted by sequence stratigraphic models, yet few reliable criteria are available to diagnose falling‐stage deltaic systems in surface exposures. Recent work on the Upper Cretaceous (Turonian) Ferron Sandstone in the western Henry Mountains Syncline of south‐central Utah has established its environment of deposition as a series of modest‐sized (5 to 20 km wide), probably asymmetrical, mixed‐influence deltas (‘Ferron Notom Delta’) that dispersed sediment eastwards from the rising Sevier orogenic hinterland into the Western Cordilleran Foreland Basin. Analysis of sandstone body stacking patterns in a 67 km long, depositional strike‐parallel (north–south) transect indicates that the growth of successive deltas was strongly forced by synsedimentary growth of a long wavelength (ca 100 km), 50 m amplitude fold structure. Herein, two discrete areas within this transect, superbly exposed in three dimensions, are documented in order to determine the details of stratal stacking patterns in the depositional dip direction, and thereby to assess the stratigraphic context of the Ferron Notom Delta. In the two study areas, dip transects expose facies representing river mouth bar to distal delta front environments over distances of 2 to 4 km. Key stratal packages are clinothems that offlap, downlap, and describe descending regressive trajectories with respective to basal and top datums; they are interpreted as the product of relative sea‐level fall. The vertical extent of clinoforms suggests that deltas prograded into <30 m of water. Furthermore, these deltaic successions preserve abundant evidence of delta front slope failure, growth faulting, and incision and filling of deep (<15 m) slope gullies. Gully fills are composed of chaotic intraformational breccia and/or massive sandstone, and constitute linear, ‘shoestring’ sandbodies in the distal portions of individual palaeodelta systems. They are interpreted to have been cut and filled during the late falling‐stage and lowstand of relative sea‐level cycles. The north–south distribution of the stratal style described above seems to be focused on the flanks of the growth anticline, and so the numerous falling‐stage systems tracts preserved within the Ferron Notom Delta probably owe their origin to synsedimentary structural growth, and the unstable fluid pressure regime that this growth imposed on the sea floor and shallow subsurface.     

Three‐dimensional architecture and hydrostratigraphy of cross‐cutting buried valleys using airborne electromagnetics,glaciated Central Lowlands,Nebraska, USA

Buried valleys are characteristic features of glaciated landscapes, and their deposits host important aquifers worldwide. Understanding the stratigraphic architecture of these deposits is essential for protecting groundwater and interpreting sedimentary processes in subglacial and ice‐marginal environments. The relationships between depositional architecture, topography and hydrostratigraphy in dissected, pre‐Illinoian till sheets is poorly understood. Boreholes alone are inadequate to characterize the complex geology of buried valleys, but airborne electromagnetic surveys have proven useful for this purpose. A key question is whether the sedimentary architecture of buried valleys can be interpreted from airborne electromagnetic profiles. This study employs airborne electromagnetic resistivity profiles to interpret the three‐dimensional sedimentary architecture of cross‐cutting buried valleys in a ca 400 km² area along the western margin of Laurentide glaciation in North America. A progenitor bedrock valley is succeeded by at least five generations of tunnel valleys that become progressively younger northward. Tunnel‐valley infills are highly variable, reflecting under‐filled and over‐filled conditions. Under‐filled tunnel valleys are expressed on the modern landscape and contain fine sediments that act as hydraulic barriers. Over‐filled tunnel valleys are not recognized in the modern landscape, but where they are present they form hydraulic windows between deep aquifer units and the land surface. The interpretation of tunnel‐valley genesis herein provides evidence of the relationships between depositional processes and glacial landforms in a dissected, pre‐Illinoian till sheet, and contributes to the understanding of the complex physical hydrology of glacial aquifers in general.     

Seismic rupture during the 1960 Great Chile and the 2010 Maule earthquakes limited by a giant Pleistocene submarine slope failure

Determining factors that limit coseismic rupture is important to evaluate the hazard of powerful subduction zone earthquakes such as the 2011 Tohoku‐Oki event (Mw = 9.0). In 1960 (Mw = 9.5) and 2010 (Mw = 8.8), Chile was hit by such powerful earthquakes, the boundary of which was the site of a giant submarine slope failure with chaotic debris subducted to seismogenic zone depth. Here, a continuous décollement is absent, whereas away from the slope failure, a continuous décollement is seismically imaged. We infer that underthrusting of inhomogeneous slide deposits prevents the development of a décollement, and thus the formation of a thin continuous slip zone necessary for earthquake rupture propagation. Thus, coseismic rupture during the 1960 and 2010 earthquakes seems to be limited by underthrusted upper plate mass‐wasting deposits. More generally, our results suggest that upper plate dynamics and resulting surface processes can play a key role for determining rupture size of subduction zone earthquakes.     

Pleistocene subglacial tunnel valleys in the central North Sea basin: 3‐D morphology and evolution

Four phases of cross‐cutting tunnel valleys imaged on 3‐D seismic datasets are mapped within the Middle–Late Pleistocene succession of the central North Sea basin (Witch Ground area). In plan the tunnel valleys form complex anastomosing networks, with tributary valleys joining main valleys at high angles. The valleys have widths ranging from 250 to 2300 m, and base to shoulder relief varying between 30 and 155 m, with irregular long‐axis profiles characteristic of erosion by water driven by glaciostatic pressures. The youngest phase of tunnel valleys are smaller and have a thinner infill than the older generations. The fill of the larger valleys comprises three seismic facies, the lowermost of which has high amplitudes and is discontinuous. The middle facies consists of wedge‐shaped packages of low‐angle dipping reflectors and is overlain by a facies characterised by sub‐horizontal reflectors, which onlap the valley margins. The seismic character, and comparison with lithologies identified in other northwest European Pleistocene tunnel valleys both onshore and offshore, suggests that the lower two seismic facies are most likely sand and gravel‐dominated, while the uppermost facies consists of glaciolacustrine and marine muds. The 3‐D morphology of the valley margins combined with the geometry of the infill packages suggest that episodic discharge of subglacial meltwater was responsible for incising the valleys and depositing at least some of the infill. Proglacial glaciofluvial deposits are inferred to account for some of the fill overlying the subglacial deposits. Glaciolacustrine and marine muds filled remaining valley topography as the ice sheet retreated. The preserved valley margins are shown to be time‐transgressive erosion surfaces that record changes in geometry of the tunnel valley system as it evolved through time, implying that valleys associated with each ice‐sheet advance/retreat cycle were dynamic and probably long‐lived. Within the constraints of the existing stratigraphy the oldest tunnel valleys in the Witch Ground area of the central North Sea are most likely to be Marine Isotope Stage (MIS) 12 (Elsterian, ca. 470 ka) in age and the youngest pre‐MIS 5e (last interglacial, ca. 120 ka). If each tunnel valley phase was formed during the retreat of a major ice sheet then four glaciations with ice coverage of the central North Sea are recorded in the pre‐Weichselian, Middle–Late Pleistocene stratigraphy. Copyright © 2006 John Wiley & Sons, Ltd.     

Simulation of localization failure with strain‐gradient‐enhanced damage mechanics

Strain gradient implies an important characteristic in localized damage deformation, which can be observed in the softening state of brittle materials, and strain gradients constitute the basic behaviours of localization failure area of the materials. The most important point in strain gradient is its damaging function including an internal length scale, which can be used to express the scale effects of mechanical responses of brittle rock mass. By extending the strain gradient theory and introducing an intrinsic material length scale into the constitutive law, the authors develop an isotropic damage model as well as a micro‐crack‐based anisotropic damage model for rock‐like materials in this paper. The proposed models were used to simulate the damage localization under uniaxial tension and plain strain compression, respectively. The simulated results well illustrated the potential of these models in dealing with the well‐known mesh‐sensitivity problem in FEM. In the computation, elements with C₁ continuity have been implemented to incorporate the proposed models for failure localization. When regular rectangle elements are encountered, the coupling between finite difference method (FDM) and conventional finite element method (FEM) is used to avoid large modification to the existing FEM code, and to obtain relatively higher efficiency and reasonably good accuracy. Application of the anisotropic model to the 3D‐non‐linear FEM analysis of Ertan arch dam has been conducted and the results of its numerical simulation coincide well with those from the failure behaviours obtained by Ertan geophysical model test. In this paper, new applications of gradient theories and models for a feasible approach to simulate localized damage in brittle materials are presented. Copyright © 2002 John Wiley & Sons, Ltd.     

Transition from storm wave‐dominated outer shelf to gullied upper slope: The mid‐Pliocene Orinoco shelf margin,South Trinidad

Shelf‐edge deltas are a key depositional environment for accreting sediment onto shelf‐margin clinoforms. The Moruga Formation, part of the palaeo‐Orinoco shelf‐margin sedimentary prism of south‐east Trinidad, provides new insight into the incremental growth of a Pliocene, storm wave‐dominated shelf margin. Relatively little is known about the mechanisms of sand bypass from the shelf‐break area of margins, and in particular from storm wave‐dominated margins which are generally characterized by drifting of sand along strike until meeting a canyon or channel. The studied St. Hilaire Siltstone and Trinity Hill Sandstone succession is 260 m thick and demonstrates a continuous transition from gullied (with turbidites) uppermost slope upward to storm wave‐dominated delta front on the outermost shelf. The basal upper‐slope deposits are dominantly mass‐transport deposited blocks, as well as associated turbidites and debrites with common soft‐sediment‐deformed strata. The overlying uppermost slope succession exhibits a spectacular set of gullies, which are separated by abundant slump‐scar unconformities (tops of rotational slides), then filled with debris‐flow conglomerates and sandy turbidite beds with interbedded mudstones. The top of the study succession, on the outer‐shelf area, contains repeated upward‐coarsening, sandstone‐rich parasequences (2 to 15 m thick) with abundant hummocky and swaley cross‐stratification, clear evidence of storm‐swell and storm wave‐dominated conditions. The observations suggest reconstruction of the unstable shelf margin as follows: (i) the aggradational storm wave‐dominated, shelf‐edge delta front became unstable and collapsed down the slope; (ii) the excavated scars of the shelf margin became gullied, but gradually healed (aggraded) by repeated infilling by debris flows and turbidites, and then new gullying and further infilling; and (iii) a renewed storm wave‐dominated delta‐front prograded out across the healed outer shelf, re‐establishing the newly stabilized shelf margin. The Moruga Formation study, along with only a few others in the literature, confirms the sediment bypass ability of storm wave‐dominated reaches of shelf edges, despite river‐dominated deltas being, by far, the most efficient shelf‐edge regime for sediment bypass at the shelf break.     

Examining the geometry,age and genesis of buried Quaternary valley systems in the Midland Valley of Scotland,UK

Buried palaeo‐valley systems have been identified widely beneath lowland parts of the UK including eastern England, central England, south Wales and the North Sea. In the Midland Valley of Scotland palaeo‐valleys have been identified yet the age and genesis of these enigmatic features remain poorly understood. This study utilizes a digital data set of over 100 000 boreholes that penetrate the full thickness of deposits in the Midland Valley of Scotland. It identified 18 buried palaeo‐valleys, which range from 4 to 36 km in length and 24 to 162 m in depth. Geometric analysis has revealed four distinct valley morphologies, which were formed by different subglacial and subaerial processes. Some palaeo‐valleys cross‐cut each other with the deepest features aligning east–west. These east–west features align with the reconstructed ice‐flow direction under maximum conditions of the Main Late Devensian glaciation. The shallower features appear more aligned to ice‐flow direction during ice‐sheet retreat, and were therefore probably incised under more restricted ice‐sheet configurations. The bedrock lithology influences and enhances the position and depth of palaeo‐valleys in this lowland glacial terrain. Faults have juxtaposed Palaeozoic sedimentary and igneous rocks and the deepest palaeo‐valleys occur immediately down‐ice of knick‐points in the more resistant igneous bedrock. The features are regularly reused and the fills are dominated by glacial fluvial and glacial marine deposits. This suggests that the majority of infilling of the features happened during deglaciation and may be unrelated to the processes that cut them.     

The post to late glacial valley reconstruction on the Haramosh north side (Mani, Baska and Phuparash valleys)

The post to late glacial valley reconstruction is focused on the Mani- Baska and Phuparash valleys on the Rakaposhi- Haramosh Muztagh in the south Karakoram. The recently glaciated valleys join the Indus valley near Sassi at 1500 m. The knowledge of the tributary valley reconstruction can be seen in the context of the scientific discussion about the extent of glaciation along the main Indus valley. Today, the recent avalanche fed glaciers come down from high lying catchment areas with an average altitude of 6700–6800 m and terminate at 2700 m. Snow line runs at 4700–4800 m in the steep flanks which is common in the Karakoram Mountains. The postglacial extent is marked by the great lateral moraine (GLM) and reached down not more than 2.5–5 km away from the recent glaciers with a calculated snow line depression of 300 m in maximum. It can be shown that the valleys were already glaciated during the lastest Late Glacial down to the valley outlet at 1500 m. The snow line was depressed 600–700 m during that period. A high glacial ice filling of the Haramosh valley and glacial erosion of the flat top of the Darchan ridge as an intermediate valley head is strongly probable.     

岩质边坡倾倒破坏的力学分析

以岩质边坡倾倒破坏地质过程分析为基础,假定岩体倾倒破坏过程中始终处于力平衡状态以及层面上下缘存在着阻止剪切错动破坏的层间阻力,岩体中某一点应力根据弹性力学原理可以简化为垂直的自重应力和水平的侧应力,将倾倒破坏岩体的力学过程概化为平面应变模型,并基于最大拉应力破坏准则,推导出岩体倾倒折断破坏深度的临界公式。实例计算及讨论表明,倾倒破坏临界深度理论适用范围广,并且考虑了边坡水平应力,计算结果更加符合实际破坏特征。另外,边坡坡角、岩层倾角及厚度对岩体倾倒破坏深度影响具有较大影响,特别是层面倾角50°～70°时边坡最易发生倾倒破坏。     

Sedimentation and continental slope processes in the vicinity of an ocean waste‐disposal site,southeastern Tasmania

Digital echo sounding, SeaBeam swath bathymetry data and sediment cores were collected on the continental slope (1500–3700 m water depth) off southeastern Tasmania in order to study sedimentary processes in the vicinity of an ocean disposal site. The new bathymetry data show that the shallower limits of the disposal site are positioned on the seaward edge of a gently dipping (3°) mid‐slope shoulder, between 1200 and 2100 m water depth. The slope below the disposal site is relatively steep (6.5°) and is cut by submarine canyons which lead into the adjacent East Tasman Saddle. The SeaBeam bathymetry data show a small submarine canyon traversing the slope in 2400 m water depth directly downslope from the disposal site, with local slopes of up to 22°. The canyon feeds into a perched basin at 2450 m, which could be acting as a local sediment trap. Short (<90 cm) gravity cores indicate that indurated erosional surfaces characterise the slope environment. The cores contain Upper Cretaceous (upper Campanian) sandstones and siltstones, which in places crop out on the sea floor where they are locally draped by a thin (0–30 cm), modern layer of hemipelagic calcareous ooze. Five cores collected from the vicinity of the disposal site had lead and zinc concentrations in the surface 1 cm of 10.3 ± 5.0 and 39.5 ± 19.6 mg/kg, respectively, significantly greater than the background values (2.9 ± 1.4 for lead and 21.2 ± 5.4 for zinc) which characterise the underlying unit that is composed of the same hemipelagic calcareous ooze. Lead and zinc are constituents of the dumped material, jarosite, which, after mixing with slope sediments, can be used as sediment tracers. One core contains a fining‐upwards bed which is also elevated in lead and zinc. This is interpreted as evidence for dispersal of the jarosite from the disposal site downslope to depths >3000 m via turbidity flows sometime during the past 24 years. Current meter data collected from 30 m above the sea floor over one year at the disposal site show that bottom currents attain speeds of up to 0.46 m/s. The current events are attributed to eddies shed by the East Australia Current. The measured bottom currents are capable of transporting fine‐grained hemipelagic muds and could provide a trigger mechanism for turbidity flows.     

Hummocky moraines in the Namaras and Susam Valleys,Central Taurids,SW Turkey

Late Quaternary glacial features have been found in the Central Taurid Mountains, in U-shaped valleys located at an altitude of more than 2000 m and surrounded by mountain ranges reaching 2850 m. No present day active glaciers exist in this area where the snowline elevation lies at about 3500 m. The Namaras Valley and its tributary Susam Valley are characterized by coarse loose material forming chaotic knob-and-kettle topography. Mounds, 1–10 m high and 10–30 m wide, are separated by 5–30 m wide, several meters deep, irregular depressions. The upper surfaces of the mounds are covered by angular to subangular limestone pebbles and blocks and internal sediments show a typical diamicton appearance with pebbles suspended in a muddy to sandy matrix. These chaotic structures are interpreted as hummocky disintegration moraines from former active glaciers. Successive cross-valley morainic ridges, up to 200 m high and several hundreds of meters long, limit the down-valley extension of these hummocks, and are interpreted as ice-marginal moraines. In the tributary Susam Valley, part of the coarse loose material forms a 200–250 m long and 90–120 m wide tongue-shaped structure with successive arcuate ridges and furrows at its down-valley reach. This structure, which is connected upward to a talus slope and perched cirque, ressembles the morphology of a periglacial rockglacier but is interpreted as the disintegration moraine controlled by small periodic retreat and readvance of the last active ice-front in this region.     

Signatures of slope failures and river‐delta collapses in a perialpine lake (Lake Lucerne,Switzerland)

Historical reports from the 17th Century document two destructive tsunamis with run‐ups exceeding 5 m, affecting proximal basins of Lake Lucerne (Switzerland). One event in ad 1601 is coeval with a strong nearby earthquake (M_W ca 5·9) which caused extensive slope failures in many parts of the lake. The second event in ad 1687 is associated with an apparently spontaneous partial collapse of the Muota river delta. This study combines high‐resolution bathymetry, reflection seismic and lithological data to document the sedimentary and morphological signatures of the two subaqueous mass movements that probably generated the observed tsunamis. Such mass movements are significant as a common sedimentation process and as a natural hazard in fjord‐type lakes and similar environments. The deposits, covering large parts of the basins with thicknesses reaching >10 m, consist of two subunits: A lower ‘massflow deposit’ contains variably deformed sediments from the source areas. Its emplacement affected pre‐existing sediments, incorporating thin sediment slices into the deposit and increasing its volume. Deep‐reaching deformation near basin margins is expressed as bulges on the lake floor. An overlying ‘megaturbidite’, featuring a graded, sandy base and a thick homogeneous muddy part, was deposited from suspended particles. The source area for the ad 1601 event, gently dipping lateral slopes with an unconsolidated hemipelagic sediment cover, hosts a pronounced slide scar with sharp escarpments and sliding surfaces. The source area for the ad 1687 event on an active delta slope has been overprinted by continued sedimentation and does not show an unambiguous scar. The case studies are exemplary for end‐member types of source areas (lateral versus delta slopes) and trigger mechanisms (seismic versus aseismic); they show that morphological mapping and reconstructions of past events are key components of a hazard assessment for mass movement‐generated tsunamis.     

不同压实度下黄土填方边坡失稳的模型试验研究

黄土填方边坡在降雨入渗下容易发生滑坡。为了探讨降雨入渗下压实度对黄土填方边坡变形破坏机制、失稳模式以及滑动机理的影响,基于室内降雨系统,结合传感器监测和三维激光扫描技术,开展了边坡压实度为80%（低压实度）、90%（中压实度）、95%（高压实度）的降雨模型试验研究,分析了压实度对填方边坡体积含水率、基质吸力以及变形破坏过程的影响规律。结果表明:压实度的不同,边坡首先破坏的位置不一。中、高压实度下的边坡最先破坏发生在坡脚处,表现出滑塌破坏;而低压实度则是在坡顶,为湿陷沉降破坏。边坡压实度越大,其变形破坏过程持续时间越长,所需累积雨量就越大,但滑动距离和滑面深度越小。随压实度的增加,边坡破坏模式由深层整体破坏向浅层多级破坏转变。低压实度边坡为湿陷沉降-深层蠕滑拉裂式,中压实度边坡为深层蠕滑拉裂式破坏,而高压实度边坡则为浅层多级后退式失稳。     

Centrifuge modeling of the geogrid-reinforced slope subjected to differential settlement

A series of centrifuge model tests of geogrid-reinforced slopes with superstructure was conducted under differential settlement condition. The influence of reinforcement placement on the deformation and failure behavior of the slope and superstructure is investigated by considering different numbers of geogrid layers. The response of the slope and superstructure is analyzed based on a full-field displacement measurement via image analysis. The differential settlement induces distinguishable superstructure movement and slope deformation above the subsidence zone. The slope displacement, close to the vertical direction, appears only in a limited zone. An integrated analysis scheme of deformation and failure processes is adopted to reveal the failure mechanism of both the unreinforced and reinforced slopes: a certain level of deformation localization induced by differential settlement results in the local failure, and adversely, the local failure aggravates the deformation localization near it. The geogrid reinforcement mechanism is further clarified as the reduction on the deformation localization of the slope due to geogrid placement. The geogrid reinforcement effect can be comprehensively described with two respects: hooping effect and shielding effect, which illustrates the influence sphere and degree of geogrid reinforcement on restraining the slope deformation. The geogrid reinforcement is proven effective to improve the safety of the slope and superstructure.

     

Holocene permafrost history and cryostratigraphy in the High‐Arctic Adventdalen Valley,central Svalbard

This paper presents the history and cryostratigraphy of the upper permafrost in the High‐Arctic Adventdalen Valley, central Svalbard. Nineteen frozen sediment cores, up to 10.7 m long, obtained at five periglacial landforms, were analysed for cryostructures, ice, carbon and solute contents, and grain‐size distribution, and were ¹⁴C‐ and OSL‐dated. Spatial variability in ice and carbon contents is closely related to the sedimentary history and mode of permafrost aggradation. In the valley bottom, saline epigenetic permafrost with pore ice down to depths of 10.7 m depth formed in deltaic sediments since the mid‐Holocene; cryopegs were encountered below 6 m. In the top 1 to 5 m, syngenetic and quasi‐syngenetic permafrost with microlenticular, lenticular, suspended and organic‐matrix cryostructures developed due to loess and alluvial sedimentation since the colder late Holocene, which resulted in the burial of organic material. At the transition between deltaic sediments and loess, massive ice bodies occurred. A pingo developed where the deltaic sediments reached the surface. On hillslopes, suspended cryostructure on solifluction sheets indicates quasi‐syngenetic permafrost aggradation; lobes, in contrast, were ice‐poor. Suspended cryostructure in eluvial deposits reflects epigenetic or quasi‐syngenetic permafrost formation on a weathered bedrock plateau. Landform‐scale spatial variations in ground ice and carbon relate to variations in slope, sedimentation rate, moisture conditions and stratigraphy. Although the study reveals close links between Holocene landscape evolution and permafrost history, our results emphasize a large uncertainty in using terrain surface indicators to infer ground‐ice contents and upscale from core to landform scale in mountainous permafrost landscapes.     

Geological controls on the geometry of incised‐valley fills: Insights from a global dataset of late‐Quaternary examples

Incised valleys that develop due to relative sea‐level change are common features of continental shelves and coastal plains. Assessment of the factors that control the geometry of incised‐valley fills has hitherto largely relied on conceptual, experimental or numerical models, else has been grounded on case studies of individual depositional systems. Here, a database‐driven statistical analysis of 151 late‐Quaternary incised‐valley fills has been performed, the aim being to investigate the geological controls on their geometry. Results of this analysis have been interpreted with consideration of the role of different processes in determining the geometry of incised‐valley fills through their effect on the degree and rate of river incision, and on river size and mobility. The studied incised‐valley fills developed along active margins are thicker and wider, on average, than those along passive margins, suggesting that tectonic setting exerts a control on the geometry of incised‐valley fills, probably through effects on relative sea‐level change and river behaviour, and in relation to distinct characteristics of basin physiography, water discharge and modes of sediment delivery. Valley‐fill geometry is positively correlated with the associated drainage‐basin size, confirming the dominant role of water discharge. Climate is also inferred to exert a potential control on valley‐fill dimensions, possibly through modulations of temperature, peak precipitation, vegetation and permafrost, which would in turn affect water discharge, rates of sediment supply and valley‐margin stability. Shelves with slope breaks that are currently deeper than 120 m contain incised‐valley fills that are thicker and wider, on average, than those hosted on shelves with breaks shallower than 120 m. No correlation exists between valley‐fill thickness and present‐day coastal‐prism convexity, which is measured as the difference in gradient between lower coastal plains and inner shelves. These findings challenge some concepts embedded in sequence stratigraphic thinking, and have significant implications for analysis and improved understanding of ‘source to sink’ sediment route‐ways, and for attempting predictions of the occurrence and characteristics of hydrocarbon reservoirs.     

Mud dispersal across a Cretaceous prodelta: Storm‐generated,wave‐enhanced sediment gravity flows inferred from mudstone microtexture and microfacies

Determining sediment transport direction in ancient mudrocks is difficult. In order to determine both process and direction of mud transport, a portion of a well‐mapped Cretaceous delta system was studied. Oriented samples from outcrop represent prodelta environments from ca 10 to 120 km offshore. Oriented thin sections of mudstone, cut in three planes, allowed bed microstructure and palaeoflow directions to be determined. Clay mineral platelets are packaged in equant, face‐face aggregates 2 to 5 μm in diameter that have a random orientation; these aggregates may have formed through flocculation in fluid mud. Cohesive mud was eroded by storms to make intraclastic aggregates 5 to 20 μm in diameter. Mudstone beds are millimetre‐scale, and four microfacies are recognized: Well‐sorted siltstone forms millimetre‐scale combined‐flow ripples overlying scoured surfaces; deposition was from turbulent combined flow. Silt‐streaked claystone comprises parallel, sub‐millimetre laminae of siliceous silt and clay aggregates sorted by shear in the boundary layer beneath a wave‐supported gravity flow of fluid mud. Silty claystone comprises fine siliceous silt grains floating in a matrix of clay and was deposited by vertical settling as fluid mud gelled under minimal current shear. Homogeneous clay‐rich mudstone has little silt and may represent late‐stage settling of fluid mud, or settling from wave‐dissipated fluid mud. It is difficult or impossible to correlate millimetre‐scale beds between thin sections from the same sample, spaced only ca 20 mm apart, due to lateral facies change and localized scour and fill. Combined‐flow ripples in siltstone show strong preferred migration directly down the regional prodelta slope, estimated at ca 1 : 1000. Ripple migration was effected by drag exerted by an overlying layer of downslope‐flowing, wave‐supported fluid mud. In the upper part of the studied section, centimetre‐scale interbeds of very fine to fine‐grained sandstone show wave ripple crests trending shore normal, whereas combined‐flow ripples migrated obliquely alongshore and offshore. Storm winds blowing from the north‐east drove shore‐oblique geostrophic sand transport whereas simultaneously, wave‐supported flows of fluid mud travelled downslope under the influence of gravity. Effective wave base for sand, estimated at ca 40 m, intersected the prodelta surface ca 80 km offshore whereas wave base for mud was at ca 70 m and lay ca 120 km offshore. Small‐scale bioturbation of mud beds co‐occurs with interbedded sandstone but stratigraphically lower, sand‐free mudstone has few or no signs of benthic fauna. It is likely that a combination of soupground substrate, frequent storm emplacement of fluid mud, low nutrient availability and possibly reduced bottom‐water oxygen content collectively inhibited benthic fauna in the distal prodelta.